Influence of HCl on oxidation of gaseous elemental mercury by dielectric barrier discharge process

The influence of HCl on the oxidation of gaseous elemental mercury (Hg0) has been investigated using a dielectric barrier discharge (DBD) plasma process, where the temperature of the plasma reactor and the composition of gas mixtures of HCl, H2O, NO, and O2 in N2 balance have been varied. We observe that Cl atoms and Cl2 molecules, created by the DBD process, play important roles in the oxidation of Hg0 to HgCl2. The addition of H2O to the gas mixture of HCl in N2 accelerates the oxidation of Hg0, although no appreciable effect of H2O alone on the oxidation of Hg0 has been observed. The increase of the reaction temperature in the presence of HCl results in the reduction of Hg0 oxidation efficiency probably due to the deterioration of the heterogeneous chemical reaction of Hg0 with chlorinated species on the reactor wall. The presence of NO shows an inhibitory effect on the oxidation of Hg0 under DBD of 16% O2 in N2, indicating that NO acts as an O and O3 scavenger. At the composition of Hg0 (280 microg m(-3)), HCl (25 ppm), NO (204 ppm), O2 (16%) and N2 (balance) and temperature 90 degrees C, we obtain the nearly complete oxidation of Hg0 at a specific energy density of 8 J l(-1). These results lead us to suggest that the DBD process can be viable for the treatment of mercury released from coal-fired power plants.     

A combined plasma photolysis (CPP) method for removal of CS2 from gas streams at atmospheric pressure

A combined plasma photolysis (CPP) reactor that utilizes a dielectric barrier discharge (DBD) plasma and 207 nm UV radiation from discharge-driven KrBr^* excimers was designed and constructed. Gas streams containing CS₂ were treated with stand-alone DBD and CPP at atmospheric pressure. In comparison to DBD, CPP greatly enhanced the removal efficiency at the same applied voltage, waste gas concentration and gas residence time. Thus the applied voltage could be reduced to a certain extent in the plasma processing of industrial wastes. Influences of the KrBr^* radiation, inlet CS₂ concentration and gas residence time on CS₂ removal by CPP were also studied. In addition, the likely reaction mechanisms for the removal of CS₂ by CPP are suggested based on the byproducts analysis. The enhanced removal efficiency and reaction mechanisms implied that the CPP process would probably be suitable for the removal of a large number of gaseous pollutants.     

介质阻挡放电氧化降解木质素磺酸钠的动力学研究

为了有效地处理难生物降解的造纸废水，采用气相介质阻挡放电产生氧化性物质，对木质素磺酸钠进行了氧化降解研究。在不同操作条件下，对其降解动力学及矿化程度进行了研究。结果表明，介质阻挡放电能有效地降解木质素磺酸钠，其氧化降解反应遵循准一级动力学反应。当峰值电压为20 kV，被水蒸气饱和的空气为气源，流量为7 L/min时，氧化处理60 min后，木质素磺酸钠降解率达到70％。其速率常数K随峰值电压、气源、气体流量和木质素磺酸钠的初始浓度的变化而不同。气体流量越大，木质素磺酸钠的初始浓度越低，速率常数K越大，降解效果越好。随着处理时间的增加，氧化性物质能将部分木质素磺酸钠矿化使溶液TOC降低，当被水蒸气饱和的空气作为气源时，氧化处理120min，21.38%的TOC被去除。     

Oxidation of elemental mercury using atmospheric pressure non-thermal plasma

The oxidation of gas phase elemental mercury (Hg0) by atmospheric pressure non-thermal plasma has been investigated at room temperature, employing both dielectric barrier discharge (DBD) of the gas mixture of Hg0 and injection of ozone (O3) into the gas mixture of Hg0. Results have shown that the oxidative efficiencies of Hg0 by DBD and the injection of O3 are 59% and 93%, respectively, with energy consumption of 23.7 J L(-1). This combined approach has indicated that O3 plays a decisive role in the oxidation of gas phase Hg0. Also the oxidation of Hg0 by injecting O3 into the gas mixture of Hg0 proceeds with better efficiency than DBD of the gas mixture of Hg0. These results have been explained by the incorporation of the competitive reaction pathways between the formation of HgO by O3 and the decomposition of HgO back to Hg0 in the plasma environment.     

The importance of the location of sodium chlorite application in a multipollutant flue gas cleaning system

In this study, removing sulfur dioxide (SO2), nitrogen oxides (NO(x)), and mercury (Hg) from simulated flue gas was investigated in two laboratory-sized bubbling reactors that simulated an oxidizing reactor (where the NO and Hg(0) oxidation reactions are expected to occur) and a wet limestone scrubber, respectively. A sodium chlorite solution was used as the oxidizing agent. The sodium chlorite solution was an effective additive that enhanced the NO(x), Hg, and SO2 capture from the flue gas. Furthermore, it was discovered that the location of the sodium chlorite application (before, in, or after the wet scrubber) greatly influences which pollutants are removed and the amount removed. This effect is related to the chemical conditions (pH, absence/presence of particular gases) that are present at different positions throughout the flue gas cleaning system profile. The research results indicated that there is a potential to achieve nearly zero SO2, NO(x), and Hg emissions (complete SO2, NO, and Hg removals and -90% of NO(x) absorption from initial values of 1500 ppmv of SO2, 200 ppmv of NO(x), and 206 microg/m3 of Hg(0)) from the flue gas when sodium chlorite was applied before the wet limestone scrubber. However applying the oxidizer after the wet limestone scrubber was the most effective configuration for Hg and NO(x) control for extremely low chlorite concentrations (below 0.002 M) and therefore appears to be the best configuration for Hg control or as an additional step in NO(x) recleaning (after other NO(x) control facilities). The multipollutant scrubber, into which the chlorite was injected simultaneously with the calcium carbonate slurry, appeared to be the least expensive solution (when consider only capital cost), but exhibited the lowest NO(x) absorption at -50%. The bench-scale test results presented can be used to develop performance predictions for a full- or pilot-scale multipollutant flue gas cleaning system equipped with wet flue gas desulfurization scrubber.     

Effect of solution pH on SO2, NO(x), and Hg removal from simulated coal combustion flue gas in an oxidant-enhanced wet scrubber

This paper presents a study on the simultaneous removal of SO2, NO(x) and Hg (both Hg0 and Hg2+) from a simulated flue gas by oxidant injection in a bench-simulated wet limestone scrubber for a wide range of slurry pH. The slurry pH strongly influenced the chemical mechanism in the scrubber and, therefore, affected pollutant removal. This paper also examines the potential ClO2(gas) reemission from a developed multipollutant scrubber at different slurry pHs. To better understand the chemical mechanisms at each slurry pH and to apply a mass balance to the process, detailed product ion analyses were performed for all experiments. Ion analysis covered three different chlorine species (chlorite, chloride, chlorate), sulfate, nitrite and nitrate. Different NO(x) removal efficiencies and mechanisms were found in acidic and alkaline pHs in the multipollutant scrubber. The acidic solution was favorable for NO and Hg0 oxidation, but increasing the slurry pH above 7.0 was disadvantageous for NO and Hg oxidation/removal. However the rate of NO(x) absorption (by percentage) was higher for the alkaline solution.     

Simultaneous removal of nitrogen oxide/nitrogen dioxide/sulfur dioxide from gas streams by combined plasma scrubbing technology

Oxides of nitrogen (NOx) [nitrogen oxide (NO) + nitrogen dioxide (NO2)] and sulfur dioxide (SO2) are removed individually in traditional air pollution control technologies. This study proposes a combined plasma scrubbing (CPS) system for simultaneous removal of SO2 and NOx. CPS consists of a dielectric barrier discharge (DBD) and wet scrubbing in series. DBD is used to generate nonthermal plasmas for converting NO to NO2. The water-soluble NO2 then can be removed by wet scrubbing accompanied with SO2 removal. In this work, CPS was tested with simulated exhausts in the laboratory and with diesel-generator exhausts in the field. Experimental results indicate that DBD is very efficient in converting NO to NO2. More than 90% removal of NO, NOx, and SO2 can be simultaneously achieved with CPS. Both sodium sulfide (Na2S) and sodium sulfite (Na2SO3) scrubbing solutions are good for NO2 and SO2 absorption. Energy efficiencies for NOx and SO2 removal are 17 and 18 g/kWh, respectively. The technical feasibility of CPS for simultaneous removal of NO, NO2, and SO2 from gas streams is successfully demonstrated in this study. However, production of carbon monoxide as a side-product (approximately 100 ppm) is found and should be considered.     

脉冲电晕低温等离子体提高一氧化氮氧化效率的实验研究

提高一氧化氮（NO）的氧化效率对于提高生物法处理该类废气的净化效率具有重要意义。实验研究了低温等离子体在脉冲电晕条件下氧化废气中NO的过程，考察了不同峰值电压、氧气含量、气体停留时间和添加有机物等因素对提高NO氧化效率的影响。结果表明：低温等离子法可有效地提高NO的氧化效率，主要产物为NO₂；室温条件下，当进气NO浓度590 mg/m³、脉冲频率50 Hz时，增大峰值电压、气体停留时间和进气中的氧气含量可提高NO的氧化效率；在最适峰值电压15 kV，气体停留时间5 s时，NO氧化效率为20%；在进气NO中添加甲苯、乙醇后，NO氧化效率可增加至30%以上，甲苯的效果要好于乙醇。     

电极尺寸对介质阻挡放电冷等离子体去除NO的影响

设计了一套高压电源装置以及相应的同轴圆柱 筒介质阻挡放电管 ,研究了放电管中心电极直径以及介质层管内径变化对放电冷等离子体去除NO的影响。实验结果表明 ,这 2种电极尺寸的变化对NO去除率有显著的影响。中心电极直径的增加 ,有助于增强放电 ,但同时减小了反应空间 ;介质层管内径增加 ,延长停留时间的同时放电的强度却相应减弱了。所以中心电极的直径或介质层的内径均应有一最佳值 ,使得其他条件不变的情况下NO的去除效果最佳。     

Effects of sulfur dioxide and nitric oxide on mercury oxidation and reduction under homogeneous conditions

This paper is particularly related to elemental mercury (Hg0) oxidation and divalent mercury (Hg2+) reduction under simulated flue gas conditions in the presence of nitric oxide (NO) and sulfur dioxide (SO2). As a powerful oxidant and chlorinating reagent, Cl2 has the potential for Hg oxidation. However, the detailed mechanism for the interactions, especially among chlorine (Cl)-containing species, SO2, NO, as well as H2O, remains ambiguous. Research described in this paper therefore focused on the impacts of SO2 and NO on Hg0 oxidation and Hg2+ reduction with the intent of unraveling unrecognized interactions among Cl species, SO2, and NO most importantly in the presence of H2O. The experimental results demonstrated that SO2 and NO had pronounced inhibitory effects on Hg0 oxidation at high temperatures when H2O was also present in the gas blend. Such a demonstration was further confirmed by the reduction of Hg2+ back into its elemental form. Data revealed that SO2 and NO were capable of promoting homogeneous reduction of Hg2+ to Hg0 with H2O being present. However, the above inhibition or promotion disappeared under homogeneous conditions when H2O was removed from the gas blend.     

滤料负载粉尘层对气态汞脱除性能的实验研究

通过不同性能纤维滤料负载燃煤飞灰粉尘层,来模拟袋式除尘器滤袋表面粉尘附着层,进而研究袋滤器用不同性能纤维滤料和粉尘附着层对燃煤烟气中Hg0的联合脱除性能。在固定床实验系统上分别进行了不同纤维滤料和燃煤飞灰粉尘层,以及经实验优选得到的华博特滤料负载燃煤飞灰粉尘层脱除燃煤烟气中Hg0的实验研究。结果表明,燃煤飞灰粉尘层和华博特滤料对Hg0分别有一定的脱除作用,脱除效率可达35%和42.5%,它们对Hg0的脱除是物理吸附和化学吸附共同作用的结果;同时,华博特滤料负载燃煤飞灰粉尘层对Hg0的联合脱除效率受到吸附反应温度、入口汞浓度和烟气停留时间等因素的影响,最佳脱汞率可达64.4%;吸附反应温度越高,脱除效率越低;烟气停留时间越大,脱除效率越高;入口汞浓度的提高并不一定提高华博特滤料负载飞灰粉尘层的脱汞效果。     

Abatement of sulfur hexafluoride emissions from the semiconductor manufacturing process by atmospheric-pressure plasmas

Sulfur hexafluoride (SF6) is an important gas for plasma etching processes in the semiconductor industry. SF6 intensely absorbs infrared radiation and, consequently, aggravates global warming. This study investigates SF6 abatement by nonthermal plasma technologies under atmospheric pressure. Two kinds of nonthermal plasma processes--dielectric barrier discharge (DBD) and combined plasma catalysis (CPC)--were employed and evaluated. Experimental results indicated that as much as 91% of SF6 was removed with DBDs at 20 kV of applied voltage and 150 Hz of discharge frequency for the gas stream containing 300 ppm SF6, 12% oxygen (O2), and 40% argon (Ar), with nitrogen (N2) as the carrier gas. Four additives, including Ar, O2, ethylene (C2H4), and H2O(g), are effective in enhancing SF6 abatement in the range of conditions studied. DBD achieves a higher SF6 removal efficiency than does CPC at the same operation condition. But CPC achieves a higher electrical energy utilization compared with DBD. However, poisoning of catalysts by sulfur (S)-containing species needs further investigation. SF6 is mainly converted to SOF2, SO2F4, sulfur dioxide (SO2), oxygen difluoride (OF2), and fluoride (F2). They do not cause global warming and can be captured by either wet scrubbing or adsorption. This study indicates that DBD and CPC are feasible control technologies for reducing SF6 emissions.     

K2Cr2O7溶液同时脱硫脱硝实验研究

采用K2Cr2O7溶液作为吸收液,在自制的鼓泡反应器内,对模拟烟气进行同时脱硫脱硝的实验研究,考察多种因素对SO2脱除率(即脱硫率)和NO脱除率(即脱硝率)的影响。实验结果表明:K2Cr2O7浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱硫率、脱硝率影响显著;当烟气流量为0.4L/min,气相中O2体积分数为6%,SO2体积分数为0.09%,NO体积分数为0.100%,K2Cr2O7摩尔浓度为10mmol/L,反应温度为40℃时,脱硫率、脱硝率分别达到100%和64.3%。     

介质阻挡放电和水吸收联合降解挥发性有机化合物

依据介质阻挡放电(DBD)和溶液吸收处理气态污染物的原理,设计出一种DBD和水吸收联合降解挥发性有机化合物(VOCs)的实验装置.研究其对甲苯的降解效果.考察了放电电压、甲苯初始浓度、模拟废气流量对甲苯降解效果的影响.分析了DBD和水吸收的相互作用.结果表明.DBD和水吸收联合可以提高甲苯的降解率.在放电电压为15.9 kV时甲苯的降解率为81.5%.比单独放电时提高了13.3百分点;甲苯的降解率随着放电电压增大而升高,随着气体流量和甲苯初始浓度增大而降低.该技术可以作为放电等离子体前处理工艺,为高效处理上业废气提供参考.     

Removal mechanism of elemental mercury by using non-thermal plasma

The removal mechanism of elementary mercury (Hg(0)) by non-thermal plasma (NTP) has been investigated, where dielectric barrier discharge and O(3) injection methods as oxidation techniques are employed, together with the analysis of mercury species deposited on the reactor surface using temperature-programmed desorption and dissociation (TPDD) and scanning electron microscopy-energy dispersive spectroscopy. The removal of Hg(0) by NTP is found to be time-dependent and proceed through three domains; the Hg(0) concentration just slightly decreases as soon as NTP is initiated and then becomes constant for several minutes (Region 1), thereafter starts to decrease rapidly for 1h (Region 2) and, after passing fall-off region, very slowly decreases for about 4h (Region 3). The deposited mercury species on the reactor surface were conglomerated like islands, rather than dispersed uniformly, and their ratio of Hg(0) to O composition is observed to be 1:2. Additionally, the new peak in TPDD spectra observed in the region of 260-380°C is proposed as HgO(3). These results lead us to conclude that the deposited mercury species by NTP have extra O atoms to oxidize the adsorbed Hg(0), resulting in the acceleration of removal rate as the oxidation of Hg(0) proceeds.     

H2O2溶液同时脱硫脱硝实验研究

二氧化硫和氮氧化物是电厂产生的主要大气污染物，研究焦点越来越集中在在一个反应器内实现同时脱硫脱硝。实验以H2O溶液作为吸收液，在自制的鼓泡反应器内，对模拟烟气进行同时脱硫脱硝的实验研究，实验结果表明：H2O浓度、反应温度、NO浓度、SO2浓度、烟气流量对脱除率影响显著，pH、氧含量对脱硝率影响不大。在整个实验范围内脱硫效率总是保持在98．5％以上，脱硝效率最高达到67．4％。     

等离子体协同MnOx/SBA-15催化降解正己醛的研究

采用浸渍法制备了MnOx/SBA-15催化剂,利用BET、XRD和SEM等对催化剂进行表征。考察了介质阻挡放电等离子体协同MnOx/SBA-15催化剂对正己醛的降解性能。结果显示,负载MnOx后的SBA-15仍然保持介孔结构,且MnOx均匀地分散在SBA-15中;等离子体与催化剂表现出较好的协同作用,干燥条件下7.5 kV的放电电压结合10%MnOx/SBA-15时降解效果最佳,正己醛去除率达99%;相比干燥条件,相对湿度低于20%时正己醛去除率变化不明显,但高于20%时催化效果明显下降;该催化剂具有很强的O3分解能力,O3在催化剂表面的分解不仅促进了正己醛的氧化,同时也提高了CO2的选择性。     

Structural effect of the in situ generated titania on its ability to oxidize and capture the gas-phase elemental mercury

Structural effect of the in situ generated TiO(2) sorbent particle was examined for its ability to capture elemental mercury under UV irradiation in a simulated combustion flue gas. Titania particles were prepared by thermal gas-phase oxidation of Titanium (IV) isopropoxide (TTIP) using a high temperature electric furnace reactor. The structural characteristics of the in situ generated TiO(2) at various synthesis temperatures were investigated; size distribution and the geometric mean diameter were measured using a scanning mobility particle sizer, while fractal dimension and radius of gyration were evaluated from the transmission electron microscopy images. Results from the Hg(0) capture experiment show that with increasing titania synthesis temperature, the overall aggregate size increases and the morphology becomes more open-structured to gas-phase Hg(0) and UV light, resulting in the improved mercury removal capability.     

鼓泡反应器中液相络合催化同时脱硫脱硝的研究

在鼓泡反应器中考察了[Co(en)3]2+同时吸收去除SO2和NO的影响因素,实验结果表明,pH值和脱硫剂种类是影响乙二胺合钴同时脱除NO和SO2的最重要影响因素,烟气中的氧促进乙二胺合钴吸收NO和SO2,烟气中的SO2,CO2和NO2对乙二胺合钴吸收NO具有抑制作用。在实验条件温度为20℃,pH为13.0,[Co(en)3]2+浓度为0.025 mol/L,加入1 g NH3.H2O的脱硝率更好,连续吸收60 min,脱硝率均保持在93.5%,加入NaOH和NH3.H2O的脱硫效果最好。乙二胺合钴络合同时脱除NO和SO2完全可以在一个装置中完成。