双极性高压脉冲介质阻挡放电脱硝实验参数优化研究

为提高机动车尾气中NO_x的去除率,采用了介质阻挡放电对NO_x进行处理,研究了介质阻挡放电反应器在不同介质参数、放电参数和气体参数条件下对NO_x去除的影响,优化了双极性高压脉冲放电的反应参数。结果表明:当放电极为直径10mm的螺纹铜棒,介质管为内径16mm、介质厚度1.5mm的石英玻璃管,放电间隙为3mm,放电长度为28cm,放电频率为60Hz,O_2体积分数为6%,NO_x初始质量浓度为536mg/m~3,气体流量为1.1L/min,单向脉冲电压为12kV,C_2H_2与NOx质量浓度比为1.5时,NO转化率和NO_x去除率分别为64.56%和22.57%。     

壳聚糖-纳米金属絮凝剂絮凝沉降水华蓝藻研究

研究了壳聚糖与纳米钛、纳米铁或妫水湖沉积物絮凝剂絮凝沉降水华蓝藻的效果。结果表明:在壳聚糖浓度为3 mg/L情况下,与妫水湖沉积物和纳米钛相比,纳米铁絮凝沉降蓝藻细胞的效果最好,在10 min内可以絮凝沉降79.5%以上的水华蓝藻细胞。进一步研究显示,在pH值为5~9的范围内,随着pH值的降低,絮凝沉降藻细胞的效率逐渐提高,pH值为5时10 min内可以絮凝去除89.6%以上的水华蓝藻细胞,具有重要的研究价值与应用价值。     

低温等离子体氧化水中难降解有机物研究

实验将介质阻挡放电与电晕放电组合在同一个反应器内,实验废水为直接大红染料溶液,将高压电极上通人50 Hz交流高压电,介质阻挡放电系统的电极间距为30 mm、电晕放电系统电极间距为25 mm、电源电压20 kV,利用常压空气中形成的雾化水电极介质阻挡放电/电晕放电低温等离子体及其活性基团作用于难降解有机物分子.实验分析了...     

高压脉冲放电等离子体对水中土霉素的降解

采用针-板式高压脉冲放电等离子体降解水中土霉素,考察了放电输出功率、空气流量、电极间距、溶液初始浓度、初始pH、初始电导率和添加Fe2+的量对土霉素去除率的影响。实验结果表明,高压脉冲放电等离子体对水中土霉素有较好的去除效率,在初始浓度200 mg/L,放电功率64 W,电极间距8 mm,空气流速0.05 m3/h,初始pH为2.6,初始电导率1.083 mS/cm条件下,反应12 min后,土霉素的去除率可达97%。向溶液中添加Fe2+,可提高土霉素的去除率。TOC随着反应时间的延长逐渐减小,反应12 min时,TOC去除率可达57%,说明大分子物质被降解为小分子物质,部分被完全矿化为CO2和H2O。     

介质阻挡放电联合催化臭氧化降解甲苯

采用介质阻挡放电区后结合MnOx/Al2O3/发泡镍去除甲苯,考察甲苯进气方式、臭氧产生方法及湿度对甲苯与O3同时去除的影响。结果表明,O3是等离子体区后催化降解甲苯的主要物种,介质阻挡放电联合催化臭氧化可实现甲苯及O3的同时高效去除。输入电压为9.0 kV时,甲苯的去除效率达92.8%,在80 min内O3的去除效率维持在99%以上。水蒸气对催化剂催化分解臭氧的活性没有直接的影响,O3浓度较高时湿度对甲苯降解效率的影响很小。GC-MS分析结果表明,甲苯降解的主要气相副产物有烷烃、酸、酮和含苯环有机物,提出了甲苯的降解途径。     

介质阻挡放电氧化降解木质素磺酸钠的动力学研究

为了有效地处理难生物降解的造纸废水，采用气相介质阻挡放电产生氧化性物质，对木质素磺酸钠进行了氧化降解研究。在不同操作条件下，对其降解动力学及矿化程度进行了研究。结果表明，介质阻挡放电能有效地降解木质素磺酸钠，其氧化降解反应遵循准一级动力学反应。当峰值电压为20 kV，被水蒸气饱和的空气为气源，流量为7 L/min时，氧化处理60 min后，木质素磺酸钠降解率达到70％。其速率常数K随峰值电压、气源、气体流量和木质素磺酸钠的初始浓度的变化而不同。气体流量越大，木质素磺酸钠的初始浓度越低，速率常数K越大，降解效果越好。随着处理时间的增加，氧化性物质能将部分木质素磺酸钠矿化使溶液TOC降低，当被水蒸气饱和的空气作为气源时，氧化处理120min，21.38%的TOC被去除。     

ZSM-5分子筛的低温等离子体再生特性

低温等离子体再生法是一种新型的吸附材料再生方法,具有快速、高效等优势。运用管式单介质阻挡放电反应器产生的低温等离子体对吸附了苯的ZSM-5分子筛进行再生处理,考察了输入功率、放电时间、密闭放电时间对吸附材料再生效果的影响,同时记录并分析了放电过程中放电状态的变化。实验结果表明:随着输入功率提高,再生效果不断提高,当输入功率达到50 W、放电时间30 min时,吸附材料基本可以达到完全再生;考察了放电时间对再生效果的影响,研究发现将放电时间压缩到15 min,再生效率仍可达70.7%;一定程度的密闭放电操作有利于脱附效率的提高。     

电晕-介质阻挡协同放电低温等离子体降解大流量甲苯废气的研究

利用自制电晕-介质阻挡协同放电低温等离子体降解大流量甲苯废气,运用均匀设计法优化获得甲苯降解的适宜条件,探究了各因素及因素间交互作用对甲苯降解的影响,并开展甲苯降解动力学分析。结果表明:降解甲苯的最佳条件为工作电压13kV、放电频率6.5kHz、废气流量为1.0L/min,甲苯初始质量浓度924mg/m~3,在此条件下甲苯气体降解率为94.93%,能量效率为0.63g/(kW·h);甲苯降解符合一级反应动力学,甲苯降解反应速率常数与输入功率具有良好线性关系。     

Fenton-like/TiO_2催化介质阻挡放电体系对活性艳蓝的降解

为了提高等离子放电对染料的降解效率,研究了Fenton-like/TiO_2耦合催化介质阻挡放电体系对活性艳蓝(X-BR)的脱色效果及降解机理。结果表明,投加Fe~(2+)或Fe~(3+)与TiO_2组成的耦合催化体系可以显著提高X-BR的脱色率。反应10 min后,紫外可见扫描光谱和阴离子(Cl~-、NO_3~-、SO_4~(2-))产量分析表明,介质阻挡放电体系可以有效破环蒽醌发色基团,耦合催化体系不仅强化了蒽醌结构的破坏,同时更加有效地破坏了苯环和萘环结构从而提高了TOC降解率。最后,比较研究了投加Mn~(2+)和Cu~(2+)对X-BR的脱色效果,在投加浓度均为0.5 mmol/L条件下,两者对X-BR的脱色起到抑制作用,因此,两者不适合作为耦合催化介质阻挡放电体系的添加离子。     

电晕放电等离子体对水中邻苯二甲酸二甲酯的降解

采用电晕放电等离子体降解水中的邻苯二甲酸二甲酯,研究了放电输出功率、溶液初始浓度、空气流量、初始p H、Fe2+和羟基自由基清除剂对邻苯二甲酸二甲酯去除效率的影响,并对其降解动力学进行了初步模拟。结果表明,电晕放电等离子体对水中邻苯二甲酸二甲酯有较好的去除效果。在放电功率45 W、初始浓度50 mg·L~(-1)、空气流速2 L·h-1、初始p H 6.31、初始电导率4.05μS·cm-1的条件下,反应30 min,邻苯二甲酸二甲酯的去除率可达到95%。酸性条件下有利于邻苯二甲酸二甲酯的降解。添加Fe2+,在反应初期可显著提高邻苯二甲酸二甲酯的降解率。羟基自由基清除剂的加入在一定程度上抑制了邻苯二甲酸二甲酯的降解。电晕放电等离子体降解邻苯二甲酸二甲酯的过程基本符合一级反应动力学。     

海南火山岩滤料曝气生物滤池工艺优化研究

本研究基于上向流曝气生物滤池污水处理系统,研究了该工艺不同气水比、不同水力停留时间、不同滤料高度层、反冲洗强度对污染物的处理效能的影响。结果表明,气水比为4∶1、水力停留时间2 h时,BAF出水中COD、NH+4-N和SS指标达到最佳;沿程污染物去除率随着滤料层高度的增加逐渐增大,当滤料高度大于1.6 m时趋于稳定,COD、NH+4-N和SS平均去除率分别达到80%、99%和80.3%。建议曝气生物滤池的反冲洗推荐程序为:先气冲(18 L/(m2·s)),单独气洗2~3 min;再气冲(18 L/(m2·s))加水冲(5 L/(m2·s)),联合反冲洗3~5 min;最后水冲(5 L/(m2·s)),漂洗5~8 min。     

腐殖酸树脂处理含Pb2+、CU2+、Ni2+废水的研究

利用泥炭为原料制备腐殖酸树脂.在动态条件下,研究了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附效果及吸附条件.同时探讨了腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的吸附与解吸再生机理,吸附机理研究表明,腐殖酸树脂对重金属离子Pb2+、Cu2+和Ni2+的主要吸附形式为离子交换吸附和络合吸附.结果表明,在废水pH值为5.0～7.0,Pb2+、Cu2+和Ni2+浓度分别为50 mg/L,经腐殖酸树脂处理,Pb2+、Cu2+和Ni2+去除率可达98%以上,且处理后废水近中性.含Pb2+、Cu2+和Ni2+电镀废水经腐殖酸树脂处理后,废水中Pb2+、Cu2+和Ni2+含量显著低于国家排放标准.     

A combined plasma photolysis (CPP) method for removal of CS2 from gas streams at atmospheric pressure

A combined plasma photolysis (CPP) reactor that utilizes a dielectric barrier discharge (DBD) plasma and 207 nm UV radiation from discharge-driven KrBr^* excimers was designed and constructed. Gas streams containing CS₂ were treated with stand-alone DBD and CPP at atmospheric pressure. In comparison to DBD, CPP greatly enhanced the removal efficiency at the same applied voltage, waste gas concentration and gas residence time. Thus the applied voltage could be reduced to a certain extent in the plasma processing of industrial wastes. Influences of the KrBr^* radiation, inlet CS₂ concentration and gas residence time on CS₂ removal by CPP were also studied. In addition, the likely reaction mechanisms for the removal of CS₂ by CPP are suggested based on the byproducts analysis. The enhanced removal efficiency and reaction mechanisms implied that the CPP process would probably be suitable for the removal of a large number of gaseous pollutants.     

凹凸棒土对腐殖酸的低温吸附性能研究

首次研究凹凸棒土对饮用水中腐殖酸的低温吸附性能,考察5℃条件下,吸附时间与腐殖酸初始浓度、吸附剂投加量、pH对凹凸棒土吸附腐殖酸的影响,确定吸附剂的吸附等温线、吸附动力学和热力学等相关理论参数,研究凹凸棒土对腐殖酸的吸附性能与机理。结果表明,江苏盱眙凹凸棒土在温度5℃、pH=4、水中腐殖酸初始浓度为5 mg/L,投加量为15 g/L的条件下,吸附180 min后对腐殖酸的去除率可达97.26%。凹凸棒土对腐殖酸的吸附符合二级吸附动力学方程与Freundlich吸附等温式,吸附过程由孔隙内扩散过程控制,吸附为自发的吸热过程,包括物理吸附与化学吸附。根据Fre-undlich吸附等温式拟合计算,5℃、pH=7时理论最大吸附量为9 mg/g,说明凹凸棒土对于低温饮用水中腐殖酸具有良好的吸附效果。     

An integrated method for removal of harmful cyanobacterial blooms in eutrophic lakes

As the eutrophication of lakes becomes an increasingly widespread phenomenon, cyanobacterial blooms are occurring in many countries. Although some research has been reported, there is currently no good method for bloom removal. We propose here a new two-step integrated approach to resolve this problem. The first step is the inactivation of the cyanobacteria via the addition of H(2)O(2). We found 60 mg/L was the lowest effective dose for a cyanobacterial concentration corresponding to 100 μg/L chlorophyll-a. The second step is the flocculation and sedimentation of the inactivated cyanobacteria. We found the addition of lake sediment clay (2 g/L) plus polymeric ferric sulfate (20 mg/L) effectively deposited them on the lake bottom. Since algaecides and flocculants had been used separately in previous reports, we innovatively combined these two types of reagents to remove blooms from the lake surface and to improve the dissolved oxygen content of lake sediments.     

Removal of Microcystins by Phototrophic Biofilms. A Microcosm Study (6 pp)

Background, Aims and Scope Microcystins (MCs) are a family of natural toxins produced by cyanobacteria (blue-green algae). As a result of eutrophication, massive cyanobacterial blooms occur more frequently and MCs represent important contaminants of freshwater ecosystems. Bacterial biodegradation is considered a main mechanism for MC breakdown in environmental conditions. While existing studies were mostly focused on MC biodegradation by planktonic bacteria, our experiments examined the fate and kinetics of MC degradation in river-originated phototrophic biofilms and investigated factors influencing the rate of MC removal. Methods The fate of dissolved MCs was studied in laboratory microcosms with different composition (containing water only, water with phytoplankton and/or phototrophic biofilms). Biofilms originated from river ecosystem were pre-incubated under various conditions (with/without presence of cyanobacterial biomass or model organic substrates: glucose and protein - casein). Changes in MC concentration (0-14 days) in water columns were measured by HPLC DAD after external additions of purified MCs (160 μg L-1, MC-LR and MC YR), and halftimes (t1/2) of MC removal were estimated. Results and Discussion The slow degradation of MC was revealed in tap water (t1/2 ~ 14 days) and river water without cyanobacteria (t1/2 ~ 8 days). Enhanced removal occurred in the presence of natural planktonic cyanobacteria (t1/2 ~ 44 h), most probably due to microorganisms associated with the biomass of cyanobacterial bloom. More rapid MC elimination occurred in the variants containing phototrophic biofilms, and was particularly pronounced at those biofilms pre-cultivated in the presence of cyanobacterial blooms (t1/2 ~ 20 h). Much slower removal was observed in the variants simulating possible substrate-dependent induction of microorganism metabolism (biofilms pre-incubated with glucose: t1/2 ~ 35 h, and casein: t1/2 ~ 80 h). After termination of experiments, total amounts of MCs accumulated in the biofilms were below 5% of the initial toxin level revealing significant biodegradation processes. Conclusion The microcosm studies contributed to understanding of the environmental fate of MCs and revealed a rapid biodegradation by phototrophic biofilms. The rate of MC elimination depends on history of biofilm community, previous contact with cyanobacteria seems to be a selective factor improving the biodegradation potential. Recommendation and Outlook Our results experimentally showed a positive role of biofilms in MC elimination during water treatment processes such as bank filtration or slow sand filtration, and could eventually serve for further research of biofilm-based technological applications for MCs removal in small-scale drinking water treatment facilities.     

微波促进含Cr(VI)-H2O2体系降解甲基橙溶液的研究

研究了微波辐射下Cr(VI)－H₂O₂催化降解甲基橙溶液的行为，探索了微波功率、微波辐射时间、pH值、H₂O₂浓度、Cr(VI)等对甲基橙溶液脱色率和COD去除率的影响。研究结果表明，Cr(VI)-H₂O₂能形成类Fenton体系；微波辐射可提高H₂O₂产生羟基自由基(·OH)的效率。1000 mg/L的甲基橙溶液，在Cr(VI)浓度为10.0 mmol/L、pH值为2.5、H₂O₂浓度为20.0 mmol/L、微波功率为700W下加热2 min，甲基橙溶液的脱色率为99.2%，COD去除率为82.8%。     

气水比对曝气生物活性炭处理原水的影响

针对从臭氧-活性炭工艺中开发出来的预臭氧-曝气生物活性炭,在不同气水比工况下进行实验,分析了不同气水比对曝气生物活性炭处理微污染原水的影响与作用。结果表明:在滤速为8～12 m/h,空床接触时间为11.5～15.4 min,装填密度为510 g/L条件下,不同气水比对去除氨氮的影响大于对CODMn的影响。气水比为0.3∶1时,对氨氮浓度为1.65～2.10 mg/L范围的进水平均去除率为81.9%,亚硝酸盐氮平均积累率为1.4%,CODMn去除率为70.6%。当气水比逐渐增加时,氨氮平均去除率有所提高,亚硝酸盐氮积累率则有所下降,对较低浓度的CODMn影响不大。     

Removal of gaseous elemental mercury by dielectric barrier discharge

The removal of elemental mercury (Hg(0)) with the reactive species produced from dielectric barrier discharge (DBD) was studied. The effects of the operating parameters, such as the applied voltage, residence time, initial concentration and co-existence of other pollutants, were investigated. The removal of Hg(0) was significantly promoted by an increase in the applied voltage of the DBD reactor system. The presence of NO gas decreased the Hg(0) removal efficiency within the range of input powers tested compared to the case of Hg(0)-only due to the competition for ozone between Hg(0) and NO gas in the DBD reactor.