Sediment Production From Forest Roads in Western Montana1

Abstract: Unpaved roads are a primary sediment source in forested watersheds. Validation of erosion models and improvements to road management require information on road erosion rates and the factors controlling erosion. This study measured sediment yields from twenty ～0.05 ha unsurfaced (native) road plots in Belt Supergroup and glacial till parent materials of western Montana, and investigated the factors controlling erosion. Annual sediment yields for individual plots ranged from 0 to 96.9 Mg/ha/yr over 3 years (2002‐2004). Annual mean sediment yield ranged from 2.1 Mg/ha in 2003 to 9.9 Mg/ha in 2004 with an overall mean of 5.4 Mg/ha/yr. The mean of log‐transformed sediment yields for sites in glacial till parent materials was higher than Belt Supergroup parent materials (p = 0.063). A regression model with road slope, time since last grading, roadbed gravel content, and precipitation as predictive variables explained 68% of the variability in sediment yield (F = 28.2; p < 0.0001). Road erosion in western Montana is limited by low erodibility of the dominant parent materials and low rainfall. Management procedures such as reducing the frequency of grading can significantly reduce sediment yields from forest roads.     

Modeling of Sediment Yield From Anjeni-Gauged Watershed,Ethiopia Using SWAT Model1

Setegn, Shimelis G., Bijan Dargahi, Ragahavan Srinivasan, and Assefa M. Melesse, 2010. Modeling of Sediment Yield From Anjeni-Gauged Watershed, Ethiopia Using SWAT Model. Journal of the American Water Resources Association (JAWRA) 46(3):514-526. DOI: 10.1111/j.1752-1688.2010.00431.x Abstract: The Soil and Water Assessment Tool (SWAT) was tested for prediction of sediment yield in Anjeni-gauged watershed, Ethiopia. Soil erosion and land degradation is a major problem on the Ethiopian highlands. The objectives of this study were to evaluate the performance and applicability of SWAT model in predicting monthly sediment yield and assess the impacts of subbasin delineation and slope discretization on the prediction of sediment yield. Ten years monthly meteorological, flow and sediment data were used for model calibration and validation. The annual average measured sediment yield was 24.6 tonnes/ha. The annual average simulated sediment yield was 27.8 and 29.5 tones/ha for calibration and validation periods, respectively. The study found that the observed values showed good agreement with the simulated sediment yield with Nash-Sutcliffe efficiency (NSE) = 0.81, percent bias (PBIAS) = 28%, RMSE-observations standard deviation ratio (RSR) = 0.23, and coefficient of determination (R²) = 0.86 for calibration and NSE = 0.79, PBIAS = 30%, RSR = 0.29, and R² = 0.84 for validation periods. The model can be used for further analysis of different management scenarios that could help different stakeholders to plan and implement appropriate soil and water conservation strategies.     

Fine‐Sediment Loadings to Lake Tahoe1

Abstract: Over the past 35 years, a trend of decreasing water clarity has been documented in Lake Tahoe, attributable in part to the delivery of fine‐grained sediments emanating from upland and channel sources. The overall objective of the research reported here was to determine the amount of fine sediment delivered to Lake Tahoe from each of the 63 contributing watersheds. The research described in this report used combinations of field‐based observations of channel and bank stability with measured and simulated data on fine‐sediment loadings to estimate fine‐sediment loadings from unmonitored basins throughout the Lake Tahoe Basin. Loadings were expressed in the conventional format of mass per unit time but also in the number of particles finer than 20 μm, the latter for future use in a lake‐clarity model. The greatest contributors of fine sediment happened to be those with measured data, not requiring extrapolation. In descending order, they are as follows: Upper Truckee River [1,010 tonnes per year (T/year)], Blackwood Creek (846 T/year), Trout Creek (462 T/year), and Ward Creek (412 T/year). Summing estimated values from the contributing watersheds provided an average, annual estimate of fine‐sediment (<0.063 mm) loadings to the lake of 5,206 T/year. A total of 7.79E + 19 particles in the 5‐20 μm fraction were calculated to enter Lake Tahoe in an average year with the Upper Truckee River accounting for almost 25% of the total. Contributions from Blackwood, Ward, Trout, and Third creeks account for another 23% of these very fine particles. Thus, these five streams making up about 40% of the basin area, account for almost 50% of all fine‐sediment loadings to the lake. Contribution of fine sediment from streambank erosion were estimated by developing empirical relations between measured or simulated bank‐erosion rates with a field‐based measure of the extent of bank instability along given streams. An average, annual fine‐sediment loading from streambank erosion of 1,305 T/year was calculated. This represents about 25% of the average, annual fine‐sediment load delivered to the lake from all sources. The two largest contributors, the Upper Truckee River (639 T/year) and Blackwood Creek (431 T/year), account for slightly more than 80% of all fines emanating from streambanks, representing about 20% of the fine sediment delivered to Lake Tahoe from all sources. Extrapolations of fine‐sediment loadings to the unmonitored watersheds are based on documented empirical relations, yet contain a significant amount of uncertainty. Except for those values derived directly from measured data, reported results should be considered as estimates.     

REELFOOT LAKE SEDIMENTATION RATES AND SOURCES1

ABSTRACT: The three basins of Reelfoot Lake, which is located in northwestern Tennessee, were investigated using the Cs-137 tracer technique to determine rates of sediment deposition and to estimate the time before the basins will fill with sediment. Blue Basin, the largest of the three basins with 2922 ha, had an average annual sedimentation rate of 0.9 cm/yr from 1984 to 1984. The basin will become too shallow for most boating and recreational activities in about 200 years. Buck Basin, the central basin with 774 ha, had an average annual sedimentation rate of 1.1 cm/yr and will become too shallow for most recreational uses in about 100 years. Upper Blue Basin, the most upstream and smallest basin with 439 ha, had an average annual sedimentation rate of 1.7 cm/yr and will become too shallow for most recreational uses in about 60 years. Two important sources of sediment to Reelfoot Lake are erosion from a large number of soybean fields and channelization of many of the streams that flow into the lake. Changes in land management that would reduce erosion could increase the time the lake would remain usable for recreational activities.     

Sediment Availability and Erosion Rates on Off‐Highway Vehicle Trails in the Ouachita Mountains,USA

Factors influencing sediment availability are assessed and erosion rates are quantified for an off‐highway vehicle (OHV) trail system in the Ouachita Mountains of Arkansas. As of May 2012, the Wolf Pen Gap trail system included 77.0 km of "trails" which consist of county roads; open and closed Forest Service roads; and open and closed OHV trails. For a given trail length, the sediment volume available to be eroded is determined by bare trail width and sediment depth. Four condition types are defined that group trail sections based on statistically different trail widths or depths. Trail construction method appears to influence sediment availability differences more than erosion potential (as indexed by trail slope gradient and length). The range for annual trail erosion rates is estimated as 75 and 210 tonne/ha/yr. The high and low rates are obtained using two independent methods. The 210 tonne/ha/yr rate is computed from mean sediment capture at 30 sediment traps installed for 0.5–1.0 year. The 75 tonne/ha/yr rate is computed assuming all available trail sediment measured in a one‐time sampling is eroded over the next year. We argue in support of this assumption and suggest both rate values may be conservative. Trail erosion rates and sediment trap observations indicate frequent trap cleanout will be needed to continue sediment capture from All Terrain Vehicle trails.     

ESTIMATING NUTRIENT AND SEDIMENT THRESHOLD CRITERIA FOR BIOLOGICAL IMPAIRMENT IN PENNSYLVANIA WATERSHEDS1

ABSTRACT: This study employs a simple nonlinear statistical approach to establish nitrogen, phosphorus, and sediment concentration and unit area load thresholds to aid in the evaluation of aquatic biological health of watersheds within the state of Pennsylvania. Flow, nitrogen and phosphorus species, sediment, basin area, land cover, and biological assessment data were assembled for 29 Pennsylvania watersheds. For each watershed, rating curves depicting flow versus load relationships were developed using the U.S. Environmental Protection Agency's (USEPA's) storage and retrieval database (STORET) flow and concentration data, then applied to daily flow data obtained from U.S. Geological Survey (USGS) daily flow gauging stations to estimate daily load between 1989 and 1999. The load estimates and concentration data were then sorted into six sets of data: mean annual unit area nitrogen, phosphorus, and sediment loads; and average nitrogen, phosphorus, and sediment concentrations. Results of Mann‐Whitney tests conducted on each of the six datasets indicate that there is a statistically significant difference between the concentrations and unit area loads of nitrogen, phosphorus, and sediment in impaired and unimpaired watersheds. Concentration thresholds, calculated as the midpoint between the impaired and unimpaired watersheds’ 95 percent confidence interval for the median, were estimated to be 2.01 mg/L, 0.07 mg/L, and 197.27 mg/L for nitrogen, phosphorus, and sediment, respectively. Annual unit area load thresholds were estimated to be equal to 8.64 kg/ha, 0.30 kg/ha, and 785.29 kg/ha, respectively, for nitrogen, phosphorus, and sediment species.     

Regional scale variability in sediment and nutrient delivery from small agricultural watersheds

Although many studies have pointed out the various controlling factors of sediment and nutrient delivery on a plot or watershed scale, little is known on the spatial variability of sediment and nutrient delivery on a regional scale. This study was conducted to reveal regional variations in sediment-associated nutrient delivery in central Belgium. Sediment deposited in 13 small retention ponds was sampled and analyzed for total phosphorus (TP), K, Mg, and Ca content. The TP content of the sediment deposits varied from 510 to 2001 mg P per kg sediment. Nutrients are predominantly fixed on the very fine sediment fraction (<16 microm), which is the reason why the nutrient trap efficiency of the ponds is only a fraction of the sediment trap efficiency. Average nutrient trap efficiency of the studied ponds varies between 4 and 31%, whereas sediment trap efficiency varies between 10 and 72%. For watersheds ranging from 7 to 4873 ha, sediment yield ranged between 1.2 and 20.6 Mg ha(-1) yr(-1), whereas TP export varied from 1.8 to 39.7 kg ha(-1) yr(-1). The observed spatial variability in nutrient losses is primarily attributed to regional variations in erosion and sediment yield values and to a far lesser degree to the spatial variations in fertilizer application. Redistribution of manure in the framework of an agricultural policy may increase the rate of nutrient delivery by ways of erosion and sediment transport.     

SEDIMENT DEPOSITION ESTIMATION FROM CESIUM-137 MEASUREMENTS1

ABSTRACT The movement of fallout ¹³⁷Cs carried by soil particles was studied as an indicator of erosion and sedimentation in the Allerton watersheds and 4-H Memorial Lake located near Monticello, Illinois. Sediment deposition was greater in the waterway draining from watershed IB than in the waterway from watershed IA. At the average rate of 2.3 cm/yr of sediment deposition in the lake (from 1954 to 1979), there will be a loss of over 2 meters of water depth in the next century. However, there appears to be a decreasing rate of sediment deposition in the 4-H Memorial Lake as a result of improved conservation practices on the watersheds and the increased effectiveness of vegetated waterways and buffers for retaining sediment.     

Sediment measurement and transport modeling: impact of riparian and filter strip buffers

Well-calibrated models are cost-effective tools to quantify environmental benefits of conservation practices, but lack of data for parameterization and evaluation remains a weakness to modeling. Research was conducted in southwestern Oklahoma within the Cobb Creek subwatershed (CCSW) to develop cost-effective methods to collect stream channel parameterization and evaluation data for modeling in watersheds with sparse data. Specifically, (i) simple stream channel observations obtained by rapid geomorphic assessment (RGA) were used to parameterize the Soil and Water Assessment Tool (SWAT) model stream channel variables before calibrating SWAT for streamflow and sediment, and (ii) average annual reservoir sedimentation rate, measured at the Crowder Lake using the acoustic profiling system (APS), was used to cross-check Crowder Lake sediment accumulation rate simulated by SWAT. Additionally, the calibrated and cross-checked SWAT model was used to simulate impacts of riparian forest buffer (RF) and bermudagrass [ (L.) Pers.] filter strip buffer (BFS) on sediment yield and concentration in the CCSW. The measured average annual sedimentation rate was between 1.7 and 3.5 t ha yr compared with simulated sediment rate of 2.4 t ha yr Application of BFS across cropped fields resulted in a 72% reduction of sediment delivery to the stream, while the RF and the combined RF and BFS reduced the suspended sediment concentration at the CCSW outlet by 68 and 73%, respectively. Effective riparian practices have potential to increase reservoir life. These results indicate promise for using the RGA and APS methods to obtain data to improve water quality simulations in ungauged watersheds.     

SAGEBRUSH RANGELAND HYDROLOGY AND EVALUATION OF THE SPUR HYDROLOGY MODEL1

ABSTRACT: An excellent hydrologic record on sagebrush range-land has been developed at the Reynolds Creek Experimental Watershed in southwestern Idaho. The objectives of this paper were two-fold: (1) to analyze and describe the hydrologic record (8–18 years) from four sagebrush watersheds (1–83 ha); and (2) to evaluate the hydrology component of SPUR, a comprehensive rangeland model. The watersheds represent a gradient in elevation (1180–1658 m) and precipitation (240–350 mm/yr). Runoff was a small fraction (> 2 percent) of the total water budget for all of the watersheds. It occurred very infrequently at the three lower elevation watersheds: Summit, Flats, and Nancy Gulch. At Lower Sheep, the highest elevation watershed, runoff occurred most years for a period of 1 to 17 weeks in the winter. Frozen soil combined with rainfall or snowmelt was associated with most of the runoff from Flats and Nancy Gulch. At Summit summertime thunderstorms produced all of the runoff. The average annual sediment yield from all of the watersheds was low (17–950 kg/ha). It was highest from Summit, which had well developed alluvial channels and very steep slopes. SPUR was able to simulate runoff with reasonable accuracy only at Summit, where frozen soils were not a factor. There was poor correlation between predicted and actual annual 8ediment loss. The model tended to overpredict evapotranspiration early in the growing season and underpredict it in the late summer.     

RESERVOIR SEDIMENTATION RATES LINKED TO LONG-TERM CHANGES IN AGRICULTURAL LANI) USE1

ABSTRACT: Long-term land use and reservoir sedimentation were quantified and linked in a small agricultural reservoir-watershed system without having historical data. Land use was determined from a time sequence of aerial photographs, and reservoir sedimentation was determined from cores with ¹³⁷Cs dating techniques. They were linked by relating sediment deposition to potential sediment production which was determined by the Universal Soil Loss Equation and by SCS estimates for gullied land. Sediment cores were collected from Tecumseh Lake, a 55-ha reservoir with a 1,189-ha agricultural watershed, constructed in 1934 in central Oklahoma. Reservoir sediment deposition decreased from an average of 5,933 Mg/yr from 1934 to 1954, to 3,179 Mg/yr from 1954 to 1962, and finally to 1,017 Mg/yr from 1962 to 1987. Potential sediment production decreased from an average of 29,892 to 11,122 and then to 3,589 Mg/yr for the same time periods as above, respectively. Reductions in deposition and sediment production corresponded to reductions in cultivated and abandoned cropland which became perennial pasture. Together, cultivated and abandoned cropland accounted for 59 percent of the watershed in 1937, 24 percent in 1954, and 10 percent in 1962. Roadway erosion, stream bank erosion, stored stream channel sediment, and long-term precipitation were considered, but none seemed to play a significant role in changing sediment deposition rates. Instead, the dominant factor was the conversion of fields to perennial pastures. The effect of conservation measures on reservoir sedimentation can now be quantified for many reservoirs where historical data is not available.     

Best Management Practices Influence Modeled Erosion Rates at Forest Haul Road Stream Crossings in Virginia

Forestry best management practices (BMPs) reduce sedimentation by minimizing soil erosion and trapping sediment. These practices are particularly important in relation to road construction and use due to the heightened potential for sediment delivery at stream crossings. This study quantifies the implementation and effectiveness of BMPs at 75 randomly selected forest road stream crossings on recent timber harvests in the Mountains, Piedmont, and Coastal Plain regions of Virginia. Road characteristics at stream crossings were used to estimate erosion using the Universal Soil Loss Equation for Forests and the Water Erosion Prediction Project for Roads. Stream crossings were evaluated based on the Virginia Department of Forestry (VDOF) BMP manual guidelines and categorized as BMP?, BMP‐standard, or BMP+ based on the quality of road template, drainage, ground cover, and stream crossing structure. BMP implementation scores were calculated for each stream crossing using VDOF audit questions. Potential erosion effects due to upgrading crossings were estimated by adjusting ground cover percentage and approach length parameters in the erosion models. Results indicate that erosion rates decrease as BMP implementation scores increase (p < 0.05). BMP‐standard and BMP+ ratings made up 83% of crossings sampled, with an average erosion rate of 6.8 Mg/ha/yr. Hypothetical improvements beyond standard BMP recommendations provided minimal additional erosion prevention.     

Impacts of Land‐Cover Change on Suspended Sediment Transport in Two Agricultural Watersheds1

Schilling, Keith E., Thomas M. Isenhart, Jason A. Palmer, Calvin F. Wolter, and Jean Spooner, 2011. Impacts of Land‐Cover Change on Suspended Sediment Transport in Two Agricultural Watersheds. Journal of the American Water Resources Association (JAWRA) 47(4):672‐686. DOI: 10.1111/j.1752‐1688.2011.00533.x Abstract: Suspended sediment is a major water quality problem, yet few monitoring studies have been of sufficient scale and duration to assess the effectiveness of land‐use change or conservation practice implementation at a watershed scale. Daily discharge and suspended sediment export from two 5,000‐ha watersheds in central Iowa were monitored over a 10‐year period (water years 1996‐2005). In Walnut Creek watershed, a large portion of land was converted from row crop to native prairie, whereas in Squaw Creek land use remained predominantly row crop agriculture. Suspended sediment loads were similar in both watersheds, exhibiting flashy behavior typical of incised channels. Modeling suggested that expected total soil erosion in Walnut Creek should have been reduced 46% relative to Squaw Creek due to changes in land use, yet measured suspended sediment loads showed no significant differences. Stream mapping indicated that Walnut Creek had three times more eroding streambank lengths than did Squaw Creek suggesting that streambank erosion dominated sediment sources in Walnut Creek and sheet and rill sources dominated sediment sources in Squaw Creek. Our results demonstrate that an accounting of all sources of sediment erosion and delivery is needed to characterize sediment reductions in watershed projects combined with long‐term, intensive monitoring and modeling to account for possible lag times in the manifestation of the benefits of conservation practices on water quality.     

EFFECTS OF LAND USE AND TOPOGRAPHY ON SOME WATER QUALITY VARIABLES IN FORESTED EAST TEXAS1

ABSTRACT: Spatial variation of five water quality variables were analyzed using composite water samples collected periodically from eight small watersheds (11.4–71.6 km²) in forested East Texas during 1977 through 1980. Based on 31 observations during the four-year period the average yield of nitrate-nitrite nitrogen (NNN), total kjeldahl nitrogen (TKN), total phosphorus (PO4), chloride (CHL), and total suspended sediment (TSS) were 1.43, 21.96, 3.09, 50.11, and 90.39 ka/ha/yr, respectively. Compared to the water quality standards of the U.S. Environmental Protection Agency (1976) and the Texas Department of Water Resources (1976) for CHL, TSS, and NNN, none of the observations exceeded the limits for public water supplies. The study showed that forested watersheds normally yielded stream flow with better quality than that from agricultural watersheds. Watersheds of greater percent of pasture area, mean slope, stream segment frequency, and drainage density produced greater concentrations for these five chemical parameters in water samples. Meaningful equations were developed for estimating mean average yields for each chemical parameter for each watershed with R² ranging from 0.77 to 0.96 and standard error of estimates from 17 to 33 percent of the observed means.     

LONG-TERM PATTERNS OF WATER QUALITY IN A MANAGED WATERSHED IN OREGON: 1. SUSPENDED SEDIMENT1

The cumulative effects of forest management activities on water quality at a downstream point were monitored from 1972-1980 during development of a watershed for timber resources. Suspended sediment concentration and turbidity were measured at two hydrologic stations which bracketed a 10-km reach of the Middle Santiam River in the Western Cascades of Oregon as it flowed through an 8000-ha block of intensively managed forest land. Slope failures often accompany road building and harvesting in steep forested watersheds and pose the most serious threat to water quality. Although 180 km of road were constructed and 3400 ha of old-growth forests were harvested from slopes averaging over 60 percent, long-term changes in sediment yields remained undetectable during the period of measurement. The geologic characteristics of the basin and the road construction and maintenance techniques as prescribed by Oregon's forest practice regulations helped to minimize the occurrence of slope failures so that long-term changes in suspended sediment export rates did not occur. Throughout the nine-year measurement period, seven slope failures which added sediment directly to streams produced measurable short-term responses at the downstream sampling location, but these erosion events were too small and too infrequent to produce long-term changes in sediment yield from the watershed.     

Development and application of a GIS-based sediment budget model

Accelerated erosion and increased sediment yields resulting from changes in land use are a critical environmental problem. Resource managers and decision makers need spatially explicit tools to help them predict the changes in sediment production and delivery due to unpaved roads and other types of land disturbance. This is a particularly important issue in much of the Caribbean because of the rapid pace of development and potential damage to nearshore coral reef communities. The specific objectives of this study were to: (1) develop a GIS-based sediment budget model; (2) use the model to evaluate the effects of unpaved roads on sediment delivery rates in three watersheds on St. John in the US Virgin Islands; and (3) compare the predicted sediment yields to pre-existing data. The St. John Erosion Model (STJ-EROS) is an ArcInfo-based program that uses empirical sediment production functions and delivery ratios to quantify watershed-scale sediment yields. The program consists of six input routines and five routines to calculate sediment production and delivery. The input routines have interfaces that allow the user to adjust the key variables that control sediment production and delivery. The other five routines use pre-set erosion rate constants, user-defined variables, and values from nine data layers to calculate watershed-scale sediment yields from unpaved road travelways, road cutslopes, streambanks, treethrow, and undisturbed hillslopes. STJ-EROS was applied to three basins on St. John with varying levels of development. Predicted sediment yields under natural conditions ranged from 2 to 7Mgkm(-2)yr(-1), while yield rates for current conditions ranged from 8 to 46Mgkm(-2)yr(-1). Unpaved roads are estimated to be increasing sediment delivery rates by 3-6 times for Lameshur Bay, 5-9 times for Fish Bay, and 4-8 times for Cinnamon Bay. Predicted basin-scale sediment yields for both undisturbed and current conditions are within the range of measured sediment yields and bay sedimentation rates. The structure and user interfaces in STJ-EROS mean that the model can be readily adapted to other areas and used to assess the impact of unpaved roads and other land uses sediment production and delivery.     

ROLE OF WATERSHED SUBDIVISION ON MODELING THE EFFECTIVENESS OF BEST MANAGEMENT PRACTICES WITH SWAT1

Distributed parameter watershed models are often used for evaluating the effectiveness of various best management practices (BMPs). Streamflow, sediment, and nutrient yield predictions of a watershed model can be affected by spatial resolution as dictated by watershed subdivision. The objectives of this paper are to show that evaluation of BMPs using a model is strongly linked to the level of watershed subdivision; to suggest a methodology for identifying an appropriate subdivision level; and to examine the efficacy of different BMPs at field and watershed scales. In this study, the Soil and Water Assessment Tool (SWAT) model was calibrated and validated for streamflow, sediment, and nutrient yields at the outlet of the Dreisbach (623 ha) and Smith Fry (730 ha) watersheds in Maumee River Basin, Indiana. Grassed waterways, grade stabilization structures, field borders, and parallel terraces are the BMPs that were installed in the study area in the 1970s. Sediment and nutrient outputs from the calibrated model were compared at various watershed subdivision levels, both with and without implementation of these BMPs. Results for the study watersheds indicated that evaluation of the impacts of these BMPs on sediment and nutrient yields was very sensitive to the level of subdivision that was implemented in SWAT. An optimal watershed subdivision level for representation of the BMPs was identified through numerical simulations. For the study watersheds, it would appear that the average subwatershed area corresponding to approximately 4 percent of total watershed area is needed to represent the influence of these BMPs when using the SWAT model.     

POTENTIAL PHOSPHORUS LOAD REDUCTIONS UNDER THE LAKE OKEECHOBEE REGULATORY PROGRAM1

ABSTRACT: Nutrient loading from beef pastures located within the northern Lake Okeechobee watershed in Florida, has been identified as a source of phosphorus contributing to the accelerated eutrophication of the lake. Since 1989 within the watershed, 557 agricultural drainage sites, mainly beef pasture, have been monitored for compliance under a regulatory program. Of those sites, 154 were actively monitored for phosphorus concentrations from October 1, 1998, to September 30, 1999. Of these 154 sites, 77 were considered to be out of compliance (OOC). An OOC site is defined as having runoff with a 12‐month average phosphorus concentration exceeding the permitted discharge limit. The average annual phosphorous load from the 77 OOC sites for an eight‐year study period from October 1, 1991, to September 30, 1999, was estimated using measured concentration values and simulated runoff obtained from an agricultural nonpoint source pollution model, CREAMS‐WT. The 77 OOC sites produced an estimated average annual 46 metric tonnes of phosphorus load, of which an estimated 22 tonnes of phosphorus reached Lake Okeechobee on an average annual basis. The remaining estimated average annual 24 tonnes of phosphorus load was retained by streams and wetlands in the discharge transport system between the sites and the lake. The estimated average annual load reaching Lake Okeechobee from the OOC sites represented 11 percent of the phosphorus load above a five‐year average annual target load for the lake. However, the OOC site drainage areas represented only 3 percent of the northern watershed that drains into the lake. Of the 77 OOC sites, 12 sites had an average annual phosphorus loading rate equal to or greater than 3.0 kg/ha and were placed on the priority list for the Critical Restoration Project in the Lake Okeechobee watershed. To estimate the possible phosphorus load reductions from the 77 sites, two scenarios were modeled. The first scenario reduced phosphorus concentrations in runoff to the permitted discharge limits under the Lake Okeechobee regulatory program. The second scenario changed current land uses to native rangeland with an estimated annual offsite total phosphorus areal loading rate of 0.114 kg/ha. These two scenarios are hypothetical with assumed concentration values and loading rate. Model results showed that the first management scenario reduced the average annual phosphorus load to the lake by an estimated 15 tonnes. The second scenario reduced the average annual phosphorus load to the lake by an estimated 21 tonnes.     

Contribution of In‐Channel Processes to Sediment Yield of an Urbanizing Watershed1

Abstract: A study was conducted between September 2003 and September 2006 to obtain baseline sediment inventories and monitor sediment transport and storage along a 3.7 km length of the channel of Valley Creek within Valley Forge National Historical Park, Pennsylvania. Valley Creek is a tributary of the Schuylkill River and drains an urbanizing 60.6 km² watershed that currently has 18% impervious land cover. Numerous field methods were employed to measure the suspended sediment yield, longitudinal profile, cross‐sections, banklines, and particle size distribution of the streambed. Suspended sediment yield for the watershed was measured at a USGS gage located just upstream of the park boundary between July 2004 and July 2005, the period corresponding to field surveys of bank erosion and channel change. The estimated suspended sediment yield of 95.7 t/km²/year is representative of a year with unusually high discharge, including a storm event that produced a peak of 78 m³/s, the second highest discharge on record for the USGS gage. Based on the median annual streamflow for the 24 years of record at the USGS gage from 1983 to 2006, the median annual sediment yield is estimated to be closer to 34 t/km²/year, considerably lower than median and mean values for other sites within the region. The mass of silt, clay, and fine sand derived from bank erosion along the 3.7 km study reach during the field survey period accounts for an estimated 2,340 t, equivalent to about 43% of the suspended sediment load. The mass of fine sediment stored in the bed along the study reach was estimated at 1,500 t, with about 330 t of net erosion during the study period. Although bank erosion appears to be a potentially dominant source of sediment by comparison with annual suspended sediment load, bed sediment storage and potential for remobilization is of the same order of magnitude as the mass of sediment derived from bank erosion.