汽车尾气中NOx再燃烧过程的动力学

为了阐明汽车尾气中ＮＯｘ再燃烧的动力学进程,以甲醛和ＮＯ２作为探针分子,通过ＦＴ－ＩＲ跟踪研究了反应体系不听民 ＨＣＯ自由基与ＮＯ２反应的动力学。结果表明,反应的主要产物中包括ＣＯ、ＣＯ２、ＮＯ、ＨＯＮＯ和Ｈ２Ｏ等分子,经长时间的反应,当体系中的ＮＯ２基本耗尽时,才有少量的Ｎ２Ｏ生成,这些产物分子分别是在几个不同的途径的连串反应在形成的。从体系中ＣＯ和ＣＯ２的生成量,测定了主反应的歧化反应速率比,     

汽车排气净化催化剂的研究

研究了ＣｕＯ／ｒ－Ａｌ２Ｏ３催化剂对正已烷的氧化活性及ＣｕＯ负载量对活性的影响；通过ＣＯ－流动法技术考察了在ＣｕＯ／ｒ－Ａｌ２Ｏ３上添加稀土ＣｅＯ２在贫氧和富氧条件下对ＣＯ的氧化活性。结果表明稀土ＣｅＯ２的添加提高了催化剂在贫氧条件下的氧化活性；该催化剂台架试验结果亦表明，催化剂具有较好的一氧化碳（ＣＯ）和烃类（ＨＣ）的氧化能力。     

负载型金催化剂用于室温下CO的消除

从催化活性、抗潮湿、抗硫中毒、稳定性等方面考察了负载型金催化剂对于ＣＯ氧化反应的性能。筛选出的２－３催化剂可在－２２℃下完全消除ＣＯ，并且在催化活性、抗潮湿、抗硫中毒、稳定性等方面具有现行催化剂无法比拟的优点。     

Fe^2＋—H2O2氧化法处理氨基J酸工业废水的研究

用Ｆｅ＾２＋－Ｈ２Ｏ２氧化法处理氨基Ｊ酸工业废水。结果表明,当溶液ｐＨ＝１－３,Ｈ２Ｏ２和Ｆｅ＾２＋用量分别为Ｈ２Ｏ２：Ｆｅ＾２＋１０：１,Ｈ２Ｏ２：ＣＯＤＣｒ＝２ｇ：ｇ时,Ｊ酸废水的ＣＯＤＣｒ去除率达６６．７％,氨基去除率达６８．４％。处理后的废水ＢＯＤ５／ＣＯＤＣｒ＝０．５,已达到生化处理的要求。该法可作为氨基Ｊ酸废水的预处理方法。     

共存离子对硫酸盐还原菌（SRB）处理含铬废水的影响研究

报道了用硫酸盐还原菌（ＳＲＢ）处理含铬（ＶＩ）废水时，共存离子Ｓｒ＾２＋，Ｃｄ＾２＋，Ｚｎ＾２＋，ＵＯ＾２＋２，Ａｇ＾＋和Ｃｌ＾－，ＳＯ２－４，ＣＯ＾２－３，ＳｉＦ＾２－６，ＥＤＴＡ柠檬酸根等存在的时的影响，在铬（ＶＩ）为５０μｇ／ｍＬ，菌量一定的条件下，铬的去除率可达８５％以上，共存离子与铬（ＶＩ）的摩尔比为４时影响较为显著，Ｃｄ＾２＋和Ａｇ＾＋使铬的去除量降低，ＵＯ＾２＋２，Ｓｒ＾２＋，Ｚｎ＾     

A^2／O生物膜法在油脂厂废水处理中的应用

Ａ＾２／Ｏ生物膜法是一种高浓度易降解有机废水处理的新工艺。用于油脂厂废水的处理,经过半年多的试运行,处理效果良好,在进水ＣＯＤ、超过设计水质时,出水ＣＯＤｃｒ超过设计水质时,出水ＣＯＤｃｒ仍能达到排放标准,ＮＨ４＾＋－Ｎ的去除率可达９０％以上,基本无污染冰生。     

载银TiO2半导体催化剂对印染废水的光降解研究

以新型载银ＴｉＯ２为催化剂，采用高压汞灯为光源对实际印染废水进行了光催化降解的研究。研究结果表明，用新型载银催化剂（简称ＴＳＡ）对印染废水和精炼废水进行深度处理的效果比用ＴｉＯ２为好。在光照１２０分钟条件下，用ＴＳＡ催化剂对印染和精炼废水生化处理出水进行光催化降解，废水的ＣＯＤｃｒ去除率分别达到７５．３％和８３．４％，比同样光降解条件下用单一ＴｉＯ２催化剂时废水的ＣＯＤｃｒ去除率提高２２．９％和２     

ZSM—5分子筛负载Pt,Pd催化剂上甲烷选择还原一氧化氮反应性？…

研究了ＺＳＭ－５分子筛负载Ｐｔ、Ｐｄ催化剂对ＣＨ４还原ＮＯ催化反应的性能。实现表明，Ｐｔ催化剂在３００－５０℃温度下，显示出较高的反应活性和Ｎ２选择性，ｄ和Ｐｔ－Ｐｄ催化剂在４００－５００℃温度下具有较好的反应性能。其活性选择性大小次序为：Ｐｔ〉Ｐｔ－Ｐｄ〉Ｐｄ。用铂氨络离子制备的催化剂反应性能优于用氯铂酸制备的催化剂。     

掺入CO催化活化CO2加氢合成甲醇的研究

用ＴＰＤ,ＴＰＳＲ－ＭＳ活性评价等方法,用Ｃｕ－Ｚｎ－Ａｌ催化剂,对ＣＯ２加氢合成甲醇的原料气掺入适量ＣＯ２进行了研究。结果表明ＣＯ２能占据催化剂表面部分ＣＯ２的吸附位,能抑制ＣＯ２加氢的逆水汽变换反应和促进甲醇合成,从而大大提高了ＣＯ２加事成甲醇的选择性和收率。     

接枝羧基淀粉去除水体中有毒重金属离子的研究

以可溶性淀粉为基体，经环氧氯丙烷交联，制备了交联淀粉。以Ｆｅ＾２＋－Ｈ２Ｏ为引发剂将丙烯腈单体接枝到交联淀粉上，再经过皂化制得水不溶性接枝羧基淀粉聚合物（ＩＳＣ）。通过红外光谱表征结构。用静态法和动态法研究ＩＳＣ去除水体中Ｃｄ＾２＋、Ｐｂ＾２＋、Ｃｕ＾２＋、Ｈｇ＾２＋、Ｃｒ２＋等离子的效果及ＰＨ值对去除效果的影响，并对其作用机理进行探讨。     

Preparation of the Mn/Co mixed oxide catalysts for low-temperature CO oxidation reaction

The Mn/Co mixed powders with various Mn/Co molar ratios were prepared by the coprecipitation method and used in low-temperature CO oxidation. The physicochemical characteristics of these powders were characterized using the Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), temperature-programmed reduction (TPR), and scanning electron microscopy (SEM) analyses. The results demonstrated that the Mn/Co molar ratio significantly affected both the textural and catalytic properties and the sample with a Mn/Co = 1:1 possessed a BET area of 123.7 m²g⁻¹ with a small mean pore size of 6.44 nm. The catalytic results revealed that the pure cobalt and manganese catalysts possessed the low catalytic activity and the pure Co catalyst is not active at temperatures lower than 140 °C. The highest catalytic activity was observed for the catalyst with a Mn/Co = 1. The obtained results showed that the incorporation of Pd into the Mn/Co catalyst significantly enhanced the catalytic activity for oxidation of carbon monoxide and the highest CO conversion was observed for the catalyst with 1 wt.% Pd and this catalyst exhibited a CO conversion of 100% at 80 ^°C.

     

Catalytic reduction of N2O over Ag-Pd/Al2O3 bimetallic catalysts

A study of the catalytic conversion of N2O to N2 over a bimetallic Ag-Pd catalyst is described in this article. Several Ag-Pd catalytic systems were prepared supported on Al2O3 with different ratios and their catalytic activity for the direct decomposition of N2O and their reduction with CO was measured. Based on the experimental results, it was observed that Ag-Pd bimetallic catalyst (5-0.5%) was the most active for both nitrous oxide reduction and direct decomposition. This high activity seems to be connected with a synergistic effect between Ag and Pd.     

Catalytic Reduction of Nitrogen Oxides in Automobile Exhaust

The catalytic reduction of oxides of nitrogen from leaded automobile exhaust has been demonstrated to be technically feasible. These studies made with copper-containing catalysts are based upon the reducing nature of exhaust caused by the carbon monoxide present. The reaction involves 2 CO + 2 NO → + N₂ + CO₂ + 178.5 Kcal.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

Catalytic oxidation of organic compounds in incineration flue gas by a commercial palladium catalyst

The object of this study is to investigate the effect of different operation conditions on the catalytic oxidation of trace organic compounds [i.e., benzene, toluene, ethylbenzene, and xylene (BTEX); and polyaromatic hydrocarbons (PAHs)] in incineration flue gas. A commercial Pd-based honeycomb catalyst, which is applied to treat flue gas with low organic concentrations and high gas velocity, is employed in this study. The investigated parameters include (1) effect of different space velocities, (2) effect of heavy metals, (3) effect of acid gas, and (4) effect of water vapor and ash particles. In this work, an effective catalyst oxidation system is constructed and expected to purify the incineration flue gas. Catalyst oxidation is a potential purification system that will meet the stricter regulations on the emissions of incineration systems. Experimental results showed that the destruction efficiency of PAHs and BTEX in Pd catalyst was generally greater than 80%. Decreasing the space velocity increased the decomposition efficiency of organic compounds. When the feedstock contained the heavy metals Pb and Cr, the oxidation of organic compounds was not inhibited. But the presence of Cd significantly decreased the oxidation efficiency. The acid gases SO2 and HCl in the flue gas could have influenced the crystal structure of PdO and subsequently deactivated/poisoned the Pd catalyst. The effect of water vapor on the catalytic destruction of PAHs and BTEX was not obvious.     

Technical Session Preliminary Schedule Announced for 1988 APCA Annual Meeting

ABSTRACT

Stable heterogeneous catalysts for the oxidative removal of CO from air at ambient temperatures have been developed. An alumina support impregnated with PdCl₂, CuCl₂, and CuSO₄ is described. Optimal activity was obtained with Pd 0.020 mol/kg, Cu 0.50 mol/kg, CuCl₂ 20-30% of total Cu, a 2- to 24-hr soak, filtration of surplus raffinate, and a 2- to 4-hr firing in air at 200-350 °C. The catalysts are effective at 20-26 °C and relative humidities in the 15-90% range. They are reversibly deactivated by completely dry or water-saturated air streams. These catalysts have been tested at space velocities up to 30,000 hr^-1. In contact with <100 ppm CO, they are highly efficient, removing ~99% of the CO with contact times of ~120 msec (pseudo-first order k' > 25 sec^-1). At much higher CO concentrations, the maximum CO loading rate—limited by the Cu(I) reoxidation rate—is approximately 17 m mol CO per Limol Pd per hour.     

铈改性Al2O3担载Pd催化剂的CO氧化性能研究

浸渍法制备了Al2O3＋CeO2为载体的Pd催化剂，对制备中各因素对催化剂效果的影响作了初步研究。考察了活性组分含量与催化剂性能的关系以及焙烧温度、水蒸气对催化剂活性的影响。结果表明，稀土Ce元素的存在使催化剂的性能得到明显改善。制备过程中焙烧步骤对催化剂的活性影响很大，催化剂制备必须高于600℃焙烧。     

Structure relationship for catalytic dechlorination rate of dichlorobenzenes in water

Three isomers of dichlorobenzene (o-, m- and p-DCB) were dechlorinated by Pd/Fe catalyst in aqueous solutions through catalytic reduction. The dechlorination reaction took place on the surface site of the catalyst via a pseudo-first-order kinetics, and resulted in benzene as the final reduction product. The rate constants of the reductive dechlorination for the three dichlorobenzenes (DCBs) in the presence of Pd/Fe as a catalyst were measured experimentally. In all cases, the reaction rate constants were found to increase with the decrease in the Gibbs free energy of the formation of DCBs. The reaction rate constant for o-, m- and p-DCBs in the presence of 0.020% (w/w) Pd/Fe at 25 °C was determined to be 0.0213, 0.0223, and 0.0254 min⁻¹, respectively. While the activation energy of each dechlorination reaction was measured to be 102.5, 96.6 and 80.0 kJ mol⁻¹ for o-, m- and p-DCBs, respectively. The results demonstrated that p-DCBs were reduced more easily than o- or m-DCBs, and the order of the tendency of the dechlorination was p-DCB > m-DCB > o-DCB. The presented data show the catalytic reduction using Pd/Fe as a catalyst is a fast and easy approach for the dechlorination of DCBs.     

Catalytic dechlorination kinetics of p-dichlorobenzene over Pd/Fe catalysts

p-Dichlorobenzene (p-DCB) was dechlorinated using Pd/Fe bimetallic catalytic reductants synthesized by chemical deposition. Batch experiments demonstrated that the Pd/Fe bimetallic particles could effectively dechlorinate p-DCB, p-DCB and its intermediate chlorobenzene were removed completely at a Pd loading of 0.02% (weight ratio of Pd to Fe) and Pd/Fe power to solution ratio about 4g 75 ml-1 in 90 min. Dechlorination was affected by various factors such as the reaction temperature, pH, Pd loading percentage over Fe and the introduction of Pd/Fe catalysts et al. Chlorobenzene represents partially stable dechlorinated intermediates in the generation of benzene and part of p-DCB was dechlorinated to benzene indirectly on the surface of Pd/Fe. The dechlorination of p-DCB took place on the surface of the Pd/Fe bimetallic particles in a pseudo-first-order reaction, the activation energy of the dechlorination reaction was determined to be 80.0 kJ mol-1 at the temperature range of 287-313 K.     

Degradation of dyes in aqueous solutions by the Fenton process

Degradation of 20 different dyes in aqueous solutions by the Fenton process was performed. These dyes include 6 types: acidic, reactive, direct, cationic, disperse and vat dyes. The former four types of dyes were decolorized and their TOC values were decreased greatly, while the color and TOC removals of the latter two types were lower. The catalytic activities of four metal ions on the degradation efficiencies of Vat Blue BO, which was chosen as a model dye because of its lowest color and TOC removals, were compared in the dark and under the ultraviolet light irradiation. The catalytic ability of different metals was Fe2+>Cu2+>Mn2+>Ag+ in the dark, and the same sequence was obtained under irradiation condition with greater degradation efficiency. Furthermore, the efficiencies of three oxidation processes, including H2O2/UV, Fe2+/H2O2 and Fe2+/H2O2/UV were compared. The results showed that the oxidation by Fe2+/H2O2/UV was the strongest, and even greater than the arithmetic sum of the other two processes, which suggests the synergistic effect of ultraviolet and ferrous ions on the degradation reaction.