Efficacy of surface sampling methods for different types of beryllium compounds

The objective of the research work was to evaluate the efficiency of three different sampling methods (Ghost Wipe?, micro-vacuum, and ChemTest?) in the recovery of Be dust by assessing: (1) four Be compounds (beryllium acetate, beryllium chloride, beryllium oxide and beryllium aluminium), (2) three different surfaces (polystyrene, glass and aluminium) and (3) inter-operator variation. The three sampling methods were also tested on site in a laboratory of a dental school for validation purposes. The Ghost Wipe? method showed recovery ranging from 43.3% to 85.8% for all four Be compounds and for all three quantities of Be spiked on Petri dishes, while recovery with the micro-vacuum method ranged from 0.1% to 12.4%. On polystyrene dishes with 0.4 μg Be, the recovery ranged from 48.3% to 81.7%, with an average recovery of 59.4% for Operator 1 and 68.4% for Operator 2. The ChemTest? wipe method with beryllium acetate, beryllium chloride, and AlBeMet? showed analogous results that are in line with the manufacturer's manual, but collection of beryllium oxide was negative. In the dental laboratory, Ghost Wipe? samplings showed better recovery than the micro-vacuum method. The ratios between the recovered quantities of Be in each location where the Ghost Wipe? was tested differed substantially, ranging from 1.45 to 64. In the dental laboratory, a faint blue color indicating the presence of Be was observed on the ChemTest? wipes used in two locations out of six. In summary, the Ghost Wipe? method was more efficient than micro-vacuuming in collecting the Be dust from smooth, non-porous surfaces such as Petri dishes by a factor of approximately 18. The results obtained on site in a dental laboratory also showed better recovery with Ghost Wipes?. However, the ratio of Be recovered by Ghost Wipes? versus micro-vacuuming was much lower for surfaces where a large amount of dust was present. Wet wiping is preferred over micro-vacuuming for beryllium forms, but this conclusion probably applies to the ultra-low particulate loading levels (0.4 micrograms or less) which was tested in this study.     

Vacuum sampling techniques for industrial hygienists, with emphasis on beryllium dust sampling

The U.S. Department of Energy (DOE) Chronic Beryllium Disease Prevention Program Rule, 10 CFR Part 850 became effective in 2000 in response to the prevalence of Chronic Beryllium Disease (CBD) in workers. The rule requires surface and air monitoring for beryllium to determine exposure levels and the evaluation of the effectiveness of controls used to minimize or eliminate that risk. The most common methods for surface sampling use wet or dry wipes. Wipe sampling techniques may be impractical for many surfaces common to most buildings such as cinder block, textured wall surfaces, fabric and carpet. Vacuum sampling methods have been developed for the evaluation of lead or pesticides on residential surfaces such as carpets, bare floors and window sills. However, the current vacuum methods may be impractical for many workplace situations such as sampling of protective clothing, complex facility structures, or equipment surfaces. Recent work using vacuum sampling for potential bio-terrorism agents such as anthrax spores may have significant application to industrial hygiene evaluations of the workplace and may be extendable for use in sampling of metals such as beryllium. Validated vacuum sampling methods that provide meaningful data would be of great value to industrial hygienists in identifying areas having surface contamination, evaluating existing controls and work practices and determining the potential of toxic material on surfaces to become airborne and present a potential risk to workers and the public. This article discusses various vacuum sampling methodologies and recommends harmonization of sampling methods.     

沙颍河流域抗生素污染特征与生态风险评价

于2018年7月 (丰水期)、11月 (枯水期) 和2019年3月(平水期)对沙颍河流域5种抗生素磺胺吡啶(SPD)、磺胺氯哒嗪(SCP)、磺胺嘧啶(SDZ)、环丙沙星(CIP)和四环素(TCL)的污染状况和空间分布进行了研究，并对其生态风险进行了评价。结果表明，沙颍河流域5种抗生素在丰水期、枯水期和平水期均有检出，丰水期CIP、枯水期SPD和SDZ以及平水期SCP的检出率均>50%，平水期SCP的检出率最高达到70.97%，CIP在丰水期的检出值最高(655 ng/L)，5种抗生素累积浓度为：丰水期>平水期>枯水期。对比国内其他地区水体环境，沙颍河流域5种抗生素浓度总体处于一般水平，但丰水期CIP检出浓度较高。相关性分析显示抗生素浓度与水质参数硬度、NH₃-N和电导率显著相关。5种抗生素的水生态风险为：丰水期>枯水期>平水期，其中CIP和TCL均为高风险。提出，应加强监测评估与预警管理，有效控制其水生态风险。     

珠三角典型河道49种抗生素污染现状及风险评估

为评估抗生素在珠三角地表水中的生态及健康风险,在石岐河布设20个监测点位,分别采集丰水期和枯水期样品,用固相萃取/超高效液相色谱-质谱法对4大类共49种抗生素进行检测。结果显示,在丰水期和枯水期样品中共检出抗生素30种,检出种类和抗生素总浓度都呈现出枯水期明显大于丰水期的现象。从总量上看,喹诺酮类是影响石岐河生态环境安全的主要抗生素类别。石岐河抗生素浓度在枯水期主要受污水处理设施出水的影响,在丰水期主要受沿岸养殖业排水的影响。采用风险熵法对生态风险进行评估,发现枯水期生态风险高于丰水期,头孢匹啉、克林霉素、诺氟沙星3种抗生素处于高生态风险级别,罗红霉素、磺胺二甲异恶唑和奥索利酸3种抗生素处于中等生态风险级别,另有4种抗生素处于低生态风险级别,应引起重视。采用健康风险评价模型对人群健康风险进行评价,发现石岐河抗生素致癌风险和非致癌风险皆处于可接受的健康风险范围内。     

Characterization of physicochemical properties of beryllium aerosols associated with prevalence of chronic beryllium disease

Little is known about the physicochemical properties of beryllium aerosols associated with increased risk of beryllium sensitization and chronic beryllium disease (CBD). Such information is needed to evaluate whether airborne mass of beryllium is the appropriate metric of exposure or alternatively to provide a scientific basis for using information on particle size, surface area, and chemistry to support an improved exposure limit based on bioavailability through the inhalation and dermal routes of exposure. Thus, we used a suite of analytical techniques to characterize aerodynamically size-fractionated beryllium particles and powders that have been associated in epidemiological studies with higher prevalence of CBD. Aerosol particles were sampled from the ventilation systems of production lines for powders of beryllium metal and beryllium oxide and for ingots of copper-beryllium alloy. End product powders from the metal and oxide production lines were also collected.Particles released during production of beryllium metal were found to be complex, having heterogeneous composition, including reactive species such as fluorine. Powders from beryllium metal production were of high purity with only a minor component of beryllium oxide. Both particles and powders from oxide production were high-purity oxide. Particles released during production of copper-beryllium alloy were heterogeneous, being predominantly copper oxides. Thus, all particles and powders contain at least some beryllium in the form of beryllium oxide.These data justify efforts to thoroughly characterize beryllium aerosol properties when performing exposure assessments. The data also suggest that differences in particle chemical composition, size, number, and surface area may influence bioavailability of beryllium and contribute to risk of CBD. However, a scientific basis does not yet exist to replace mass as the current metric of exposure.     

Distribution and sources of polycyclic aromatic hydrocarbons in the surface water of Taizi River, Northeast of China

Spatial and seasonal distribution and sources of 16 polycyclic aromatic hydrocarbons (PAHs), identified as priority pollutants by the US Environmental Protection Agency, were investigated in the surface water of the Taizi River in Liaoning Province, northeast of China. Samples were collected from the mainstream, and tributaries of the Taizi River in dry, wet, and normal seasons. Five important industrial point sources were also monitored. The total PAH concentrations ranged from 454.5 to 1,379.7 ng l^?1 in the dry season, 1,801.6 to 5,868.9 ng l^?1 in the wet season, and 367.0 to 5,794.5 ng l^?1 in the normal season. The total PAH concentrations were significantly increased in the order of wet season > normal season > dry season. The profile of PAHs in the surface water samples was dominated by low molecular weight PAHs particularly with two- and three-ring components in the three seasons, suggesting that the PAHs were from a relatively recent local source. Source identification inferred that the PAHs in the surface water of the Taizi River came from both petrogenic inputs and pyrogenic sources.     

Atmospheric deposition of major ions and trace metals near an industrial area,Jordan

Al, Cd, Cr, Cu, Fe, Mn, Pb, Zn, NH4+, Mg2+, Ca2+, Na+, K+, Cl-, NO3- and SO4(2-), along with pH were determined in wet and dry deposition samples collected at Al-Hashimya, Jordan. Mean trace metal concentrations were similar or less than those reported for other urban regions worldwide, while concentrations of Ca2+ and SO4(2-) were the highest. The high Ca2+ concentrations were attributed to the calcareous nature of the local soil and to the influence of the Saharan dust, while the high concentrations of SO4(2-) were attributed to the influence of anthropogenic sources and Saharan dust soil. Except for SO4(2-), NO3-, and Ca2+, dry deposition fluxes of measured metals and ions were higher than their corresponding wet deposition fluxes. The high annual average pH values recorded for wet and dry deposition samples were attributed to the neutralization of acidity by alkaline species. Cd, Cr, Cu, Pb, Zn, NO3- and SO4(2-) were enriched in wet and dry deposition samples relative to crustal material, and a significant anthropogenic contribution to these elements and ions is tentatively suggested. Finally, the possible sources and the main factors affecting the concentrations of the measured species are discussed.     

Substrate influence on epiphytic lichens

The origin of the presence of soil elements in the epiphytic lichen Lecanora conizaeoides was investigated in an area of heavily polluted soil (The Broekpolder The Netherlands). Analysis results of lichens, bark and tree rings of the supporting trees indicated that for As, Co, Cr, Cu, Fe, Hg, Sc and V the levels in lichens may be considered to originate from wet and dry deposition. The Cd, Mn and Zn levels in lichens might have originated from both wet and dry deposition and the substrate bark. For these three elements, in particular, accumulation characteristics in lichens should be further investigated.     

Preparation, certification and interlaboratory analysis of workplace air filters spiked with high-fired beryllium oxide

Occupational sampling and analysis for multiple elements is generally approached using various approved methods from authoritative government sources such as the National Institute for Occupational Safety and Health (NIOSH), the Occupational Safety and Health Administration (OSHA) and the Environmental Protection Agency (EPA), as well as consensus standards bodies such as ASTM International. The constituents of a sample can exist as unidentified compounds requiring sample preparation to be chosen appropriately, as in the case of beryllium in the form of beryllium oxide (BeO). An interlaboratory study was performed to collect analytical data from volunteer laboratories to examine the effectiveness of methods currently in use for preparation and analysis of samples containing calcined BeO powder. NIST SRM(?) 1877 high-fired BeO powder (1100 to 1200 °C calcining temperature; count median primary particle diameter 0.12 μm) was used to spike air filter media as a representative form of beryllium particulate matter present in workplace sampling that is known to be resistant to dissolution. The BeO powder standard reference material was gravimetrically prepared in a suspension and deposited onto 37 mm mixed cellulose ester air filters at five different levels between 0.5 μg and 25 μg of Be (as BeO). Sample sets consisting of five BeO-spiked filters (in duplicate) and two blank filters, for a total of twelve unique air filter samples per set, were submitted as blind samples to each of 27 participating laboratories. Participants were instructed to follow their current process for sample preparation and utilize their normal analytical methods for processing samples containing substances of this nature. Laboratories using more than one sample preparation and analysis method were provided with more than one sample set. Results from 34 data sets ultimately received from the 27 volunteer laboratories were subjected to applicable statistical analyses. The observed performance data show that sample preparations using nitric acid alone, or combinations of nitric and hydrochloric acids, are not effective for complete extraction of Be from the SRM 1877 refractory BeO particulate matter spiked on air filters; but that effective recovery can be achieved by using sample preparation procedures utilizing either sulfuric or hydrofluoric acid, or by using methodologies involving ammonium bifluoride with heating. Laboratories responsible for quantitative determination of Be in workplace samples that may contain high-fired BeO should use quality assurance schemes that include BeO-spiked sampling media, rather than solely media spiked with soluble Be compounds, and should ensure that methods capable of quantitative digestion of Be from the actual material present are used.     

Interlaboratory evaluation of an extraction and fluorescence method for the determination of trace beryllium in soils

Analytical methods for the determination of trace beryllium in soils are needed so that anthropogenic sources of this element can be distinguished from native (background) levels of beryllium. In this work, a collaborative interlaboratory evaluation of a new extraction and fluorescence-based procedure for determining beryllium in soil samples was carried out to fulfil method validation requirements for ASTM International voluntary consensus standard test methods. A Canadian reference material, CCRMP Till-1 soil, with a background beryllium concentration of 2.4 microg g(-1), was selected for study. This certified reference material (CRM) was spiked and homogenized with varying levels of beryllium oxide in order to give batches of material with beryllium concentrations of 4.36 +/- 0.69, 11.5 +/- 0.7, 124 +/- 7 and 246 +/- 16 microg g(-1) (+/- values are standard deviations). In the interlaboratory study (ILS), which was carried out in accordance with an applicable ASTM International standard practice (ASTM E691), samples of these spiked soils were subjected to extraction in dilute ammonium bifluoride at approximately 90 degrees C for 40 h. Fluorescence measurement of the extracted beryllium was carried out via detection using the high quantum yield fluorophore, hydroxybenzoquinoline sulfonate (HBQS). Interlaboratory precision estimates from six participating laboratories ranged from 0.048 to 0.103 (relative standard deviations) for the five different beryllium concentrations. Pooled bias estimates resulting from this ILS were between -0.049 and 0.177 for the various beryllium levels. These figures of merit support promulgation of the analytical procedure as an ASTM International standard test method.     

Validation of a standardized portable fluorescence method for determining trace beryllium in workplace air and wipe samples

Beryllium is widely used in industry for its unique properties; however, occupational exposure to beryllium particles can cause potentially fatal disease. Consequently, exposure limits for beryllium particles in air and action levels on surfaces have been established to reduce exposure risks for workers. Field-portable monitoring methods for beryllium are desired in order to facilitate on-site measurement of beryllium in the workplace, so that immediate action can be taken to protect human health. In this work, a standardized, portable fluorescence method for the determination of trace beryllium in workplace samples, i.e., air filters and dust wipes, was validated through intra- and inter-laboratory testing. The procedure entails extraction of beryllium in 1% ammonium bifluoride (NH(4)HF(2), aqueous), followed by fluorescence measurement of the complex formed between beryllium ion and hydroxybenzoquinoline sulfonate (HBQS). The method detection limit was estimated to be less than 0.02 microg Be per air filter or wipe sample, with a dynamic range up to greater than 10 microg. The overall method accuracy was shown to satisfy the accuracy criterion (A< or = +/-25%) for analytical methods promulgated by the US National Institute for Occupational Safety and Health (NIOSH). Interferences from numerous metals tested (in >400-fold excess concentration compared to that of beryllium) were negligible or minimal. The procedure was shown to be effective for the dissolution and quantitative detection of beryllium extracted from refractory beryllium oxide particles. An American Society for Testing and Materials (ASTM) International voluntary consensus standard based on the methodology has recently been published.     

Seasonal effect on trace metal elements behaviour in a reservoir of northern Thailand

Trace metal elements (TME) can be real threats for living organisms. However, few studies dealt with TME in reservoirs in rural areas where farming practises could induce negative effects. Mae Thang reservoir (northern Thailand) has been studied for 3 years to understand the seasonal behaviour of dissolved TME: Fe, Mn, Cd, Al, Pb, V, Cr, Co, Ni, Cu, Zn, Mo, U and As and associated physicochemical parameters. In situ measurements of these parameters were done during the dry and the wet seasons as well as water samples along the water column for further analyses and TME determination by inductively coupled plasma-mass spectrometry (ICP-MS). In the dry season, the water column was characterized by a strong stratification and anoxic conditions in the hypolimnion. High rain and water input from the watershed during the wet season induced mixing of the water. All TME, except Ni, Co and Cr were less concentrated in the wet season indicating a dilution effect by water input. There was thus no important dissolved pollution coming from the watershed. The anoxic conditions in the dry season enhanced the reduction of Fe and Mn and the desorption processes. Depth, and thus oxic–anoxic conditions were the main drivers of TME in the dry season, while in the wet season, dissolution processes from parent rocks of watershed were favoured. The average concentrations of TME in the reservoir were in the limit of the international and Thai standards. Only localized values in the bottom of the reservoir for Fe and Mn were higher than the limits.     

The contribution of roadside soil to phosphorus loading in the eutrophic Lagos Lagoon, Nigeria

Roadside soils were sampled from the Lagos Lagoon catchment during the wet and dry seasons over the period 2005-2009. Lagoon sediment samples were also collected within the same period. All samples were digested with aqua regia to determine total phosphorus and extracted with 0.5 M sodium bicarbonate to determine the bioavailable fraction (Olsen-P). A segmented flow analyser method was used for analysis and good accuracy was demonstrated for two reference soils (SO-2 from CCMET and SRM 2711 from NIST). The Lagos Lagoon is a hypereutrophic water body (1270 ± 1170 μg P L(-1)), with significant areas of anoxia and water hyacinth growth. The total phosphorus concentrations in roadside soils (16 sites; mean ± 2 S.D.) were 285 ± 279 mg kg(-1) in the wet season and 424 ± 629 mg kg(-1) in the dry season, indicating that rainwater leaching is a major source of phosphorus in the lagoon. The bioavailable fractions were 5.17 ± 3.47 mg kg(-1) (2.1 ± 1.5% of the total) in the wet season and 13.0 ± 8.7 mg kg(-1) (4.3 ± 4.5% of the total) in the dry season.     

Study of the Climate Change Impacts on Water Quality in the Upstream Portion of the Cau River Basin,Vietnam

This paper presents simulations of climate change impacts on water quality in the upstream portion of the Cau River Basin in the North of Vietnam. The integrated modeling system GIBSI was used to simulate hydrological processes, pollutant and sediment wash-off in the river basin, and pollutant transport and transformation in the river network. Three projections for climate change based on emission scenarios B1, B2, and A2 of IPCC Special Report on Emission Scenarios (SRES) were considered. By assuming that the input pollution sources and watershed configuration were constant, based on 2008 data, water quality in the river network was simulated up to the terminal year 2050. For each climate change scenario, patterns of precipitation in wet and dry year were considered. The change in annual and monthly trends for dissolved oxygen (DO), biochemical oxygen demand (BOD), and ammonium ions (NH4+) load and concentration for different portions of the watershed have been analyzed. The results of these simulations show that climate change has more impact on changing the seasonal water quality parameters than on altering the average annual load of the pollutants. The percent change and change pattern in water quality parameters are different for wet and dry year, and the changes in wet year are smaller than those in dry year.     

Classification of moisture and aeration regimes in sub-boreal forest soils

One hundred and two white spruce (Picea glauca (Moench) Voss) stands were studied in the Sub-boreal Spruce zone of British Columbia and were quantitatively classified into seven soil moisture regimes (moderately dry, slightly dry, fresh, moist, very moist, wet, and very wet) according to actual/potential evapotranspiration ratio, depth to gleyed layer or prominent mottling, and depth to groundwater table. The delineated soil moisture regimes demonstrated strong relationships with the composition of understory vegetation and white spruce foliar nutrients and site index. These relationships implied that the three differentiating characteristics used in the classification provided a good estimation of growing-season soil water supply. In addition to soil moisture regimes, three soil aeration regimes (adequate, restricted, and deficient) were delineated according to presence or absence of gleyed horizons and groundwater table, slope gradient, and soil texture. These soil aeration regimes helped in explaining the variation in white spruce site index, especially on water-surplus sites. Thus, an integrated classification of soil moisture-aeration regimes was proposed to explain the effect of soil moisture and aeration on white spruce productivity.The results of this study gave further evidence that soil moisture and aeration regimes, differentiated on the basis of climatic data and soil morphological properties, are useful measures of soil moisture and aeration conditions in sub-boreal forest soils.     

Sources and seasonal variation of PAHs in the sediments of drinking water reservoirs in Hong Kong and the Dongjiang River (China)

The main objective of this study was to investigate occurrence of polycyclic aromatic hydrocarbons (PAHs) in the sources of the drinking water supply of Hong Kong. The main emphasis was on the Dongjiang River in mainland China which is the major source, supplying 80% of the total consumption in Hong Kong (the remaining 20% is obtained from rain water). Sediments were collected from four sites along the Dongjiang River and four reservoirs in Hong Kong during both the dry and wet weather seasons. The concentrations of total PAHs in the sediments ranged between 36 and 539 microg/kg dry wt. The lower levels were detected at the upstream site on the Dongjiang River and at the reservoirs in Hong Kong (44-85 microg/kg dry wt), while the mid- and downstream sites on the Dongjiang River were more polluted (588-658 microg/kg dry wt). Examination of the PAH profiles revealed that the mid- and downstream sections of the Dongjiang River contained high percentages of 4,5,6-ring PAHs, similar to the amounts of atmospheric particulate matter and road dust collected during the dry weather season from the Pearl River Delta region as reported in the literature. Seasonal changes were revealed in the reservoirs of Hong Kong, with higher PAH levels in the wet weather season than in the dry weather season. For those reservoirs in Hong Kong that store water from the Dongjiang River, a distinct seasonal pattern was also observed, namely, that under dry weather season conditions the PAHs found in the sediments were primarily from petrogenic source, while under wet weather season conditions they were from pyrolytic sources. No such pattern was detected in the reservoirs which stored only rain water.     

刘家峡水库藻类群落特征与水质的关系

2009年—2010年，研究了刘家峡水库的藻类群落特征。共鉴定出8门11纲 16目33科55 属114种藻。丰水期优势类群是金藻门（占27%），次优势类群是硅藻门（21.5%）；枯水期优势类群是硅藻门，占总数34%（羽纹纲占33%），次优势类群是金藻门（18%）。对刘家峡水库水质初步评价结果显示：水库上游水质较清洁（1#—2#站点），中下游为轻度—偏中度污染（3#—4#站点），下游为中度—偏重度污染（5#—6#站点）。对藻类群落特征与6项水环境因子的Pearsong相关性分析表明，枯水期影响藻类群落特征的环境因子依次是DO﹥TN﹥pH值﹥T﹥Mcb(粪大肠杆菌)；丰水期则是DO﹥Mcb﹥pH值﹥TN。     

Total estrogenic activity and nonylphenol concentration in the Donggang River, Taiwan

We report a survey on the occurrence and distribution of nonylphenol (NP) and 17β-estradiol equivalent quotient (EEQ) concentrations in Donggang River, Taiwan. Concentrations of NP were measured with a high-performance liquid chromatography/fluorescent system and EEQs were carried with an MVLN cell line. Concentrations of NP ranged from less than 93 to 511 ng/L; EEQs ranged from less than 0.16 to 8.64 ng-E2/L. Concentrations of NP were higher in the dry season than in the wet season, which was affected by a high flow rate. In the main watercourse, higher EEQ occurred in the wet season than in the dry season; rainfall may have flushed substances containing estrogenic activity. NP and EEQ concentrations occurred in seawater only in the dry season, especially high EEQ values, and were not detected in the wet season. The reasons are not clear at this moment. Furthermore, NP concentrations provided low contribution to the total estrogenic activity.     

Contributions of dry and wet depositions of polychlorinated dibenzo-p-dioxins and dibenzofurans to a contaminated site resulting from a penetachlorophenol manufacturing process

The soils at a factory for manufacturing pentachlorophenol were heavily contaminated by polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). In order to verify the contributions of dry and wet deposition of PCDD/Fs from the ambient air, the concentration of PCDD/Fs in ambient air and soil were measured, the partition of particle- and gas-phases of atmospheric PCDD/Fs was calculated, and the annual fluxes of total dry and wet PCDD/F depositions were modeled. Average atmospheric PCDD/F concentration was 1.24 ng Nm^???3 (or 0.0397 ng I-TEQ Nm^???3). Moreover, over 92.8% of total PCDD/Fs were in the particle phase, and the dominant species were high chlorinated congeners. The total PCDD/F fluxes of dry and wet deposition were 119.5 ng m^???2 year^???1 (1.34 ng I-TEQ m^???2 year^???1) and 82.0 ng m^???2 year^???1 (1.07 ng I-TEQ m^???2 year^???1), respectively. By scenario simulation, the total fluxes of dry and wet PCDD/F depositions were 87.1 and 68.6 ng I-TEQ, respectively. However, the estimated PCDD/F contents in the contaminated soil were 839.9 ?? g I-TEQ. Hence, the contributions of total depositions of atmospheric PCDD/F were only 0.02%. The results indicated that the major sources of PCDD/F for the contaminated soil could be attributed to the pentachlorophenol manufacturing process.     

大连市中心城区地下水“三氮”污染分析

依据《地下水质量标准》(GB/T 14848-1993),对大连市中心城区2006-2010年地下水"三氮"监测资料进行分析。结果表明,"三氮"的检出率(最高为100%)和超标率(最高为58.8%)都较高,其中亚硝酸盐氮超标显著。氨氮浓度各年均值均超标,呈波动变化;亚硝酸盐氮浓度各年均值均超标,并呈上升趋势;硝酸盐氮各年均值波动变化,总体呈上升趋势。除2009年以外,其他4年中丰水期的硝酸盐氮浓度都比枯水期高;除2007年外,其他4年中的丰水期氨氮浓度都比枯水期低。"三氮"最高浓度值主要出现在中心城区周边区域。