Recovery of volatile fatty acids via membrane contactor using flat membranes: Experimental and theoretical analysis

Volatile fatty acid (VFA) separation from synthetic VFA solutions and leachate was investigated via the use of a membrane contactor. NaOH was used as a stripping solution to provide constant concentration gradient of VFAs in both sides of a membrane. Mass flux (12.23 g/m² h) and selectivity (1.599) observed for acetic acid were significantly higher than those reported in the literature and were observed at feed pH of 3.0, flow rate of 31.5 ± 0.9 mL/min, and stripping solution concentration of 1.0 N. This study revealed that the flow rate, stripping solution strength, and feed pH affect the mass transfer of VFAs through the PTFE membrane. Acetic and propionic acid separation performances observed in the present study provided a cost effective and environmental alternative due to elimination of the use of extractants.     

Changes in cadmium mobility during composting and after soil application

The effect of twelve weeks of composting on the mobility and bioavailability of cadmium in six composts containing sewage sludge, wood chips and grass was studied, along with the cadmium immobilization capacity of compost. Two different soils were used and Cd accumulation measured in above-ground oat biomass (Avena sativa L.). Increasing pH appears to be an important cause of the observed decreases in available cadmium through the composting process. A pot experiment was performed with two different amounts of compost (9.6 and 28.8 g per kg of soil) added into Fluvisol with total Cd 0.255 mg kg^?1, and contaminated Cambisol with total Cd 6.16 mg kg^?1. Decrease of extractable Cd (0.01 mol l^?1 CaCl₂) was found in both soils after compost application. The higher amount of compost immobilized an exchangeable portion of Cd (0.11 mol l^?1 CH₃COOH extractable) in contaminated Cambisol unlike in light Fluvisol. The addition of a low amount of compost decreased the content of Cd in associated above-ground oat biomass grown in both soils, while a high amount of compost decreased the Cd content in oats only in the Cambisol.     

Changes in the microbial communities during co-composting of digestates

Anaerobic digestion is a waste treatment method which is of increasing interest worldwide. At the end of the process, a digestate remains, which can gain added value by being composted. A study was conducted in order to investigate microbial community dynamics during the composting process of a mixture of anaerobic digestate (derived from the anaerobic digestion of municipal food waste), green wastes and a screened compost (green waste/kitchen waste compost), using the COMPOCHIP microarray. The composting process showed a typical temperature development, and the highest degradation rates occurred during the first 14 days of composting, as seen from the elevated CO₂ content in the exhaust air. With an exception of elevated nitrite and nitrate levels in the day 34 samples, physical–chemical parameters for all compost samples collected during the 63 day process indicated typical composting conditions. The microbial communities changed over the 63 days of composting. According to principal component analysis of the COMPOCHIP microarray results, compost samples from the start of the experiment were found to cluster most closely with the digestate and screened compost samples. The green waste samples were found to group separately. All starting materials investigated were found to yield fewer and lower signals when compared to the samples collected during the composting experiment.     

Utilization of solar energy in sewage sludge composting: Fertilizer effect and application

Three reactors, ordinary, greenhouse, and solar, were constructed and tested to compare their impacts on the composting of municipal sewage sludge. Greenhouse and solar reactors were designed to evaluate the use of solar energy in sludge composting, including their effects on temperature and compost quality. After 40 days of composting, it was found that the solar reactor could provide more stable heat for the composting process. The average temperature of the solar reactor was higher than that of the other two systems, and only the solar reactor could maintain the temperature above 55 °C for more than 3 days. Composting with the solar reactor resulted in 31.3% decrease in the total organic carbon, increased the germination index to 91%, decreased the total nitrogen loss, and produced a good effect on pot experiments.     

The effects of apple pomace,bentonite and calcium superphosphate on swine manure aerobic composting

The effects of additives such as apple pomace, bentonite and calcium superphosphate on swine manure composting were investigated in a self-built aerated static box (90 L) by assessing their influences on the transformation of nitrogen, carbon, phosphorous and compost maturity. The results showed that additives all prolonged the thermophilic stage in composting compared to control. Nitrogen losses amounted to 34–58% of the initial nitrogen, in which ammonia volatilization accounted for 0.3–4.6%. Calcium superphosphate was helpful in facilitating composting process as it significantly reduced the ammonia volatilization during thermophilic stage and increased the contents of total nitrogen and phosphorous in compost, but bentonite increased the ammonia volatilization and reduced the total nitrogen concentration. It suggested that calcium superphosphate is an effective additive for keeping nitrogen during swine manure composting.     

Effect of temperature on bacterial emissions in composting of swine manure

Swine manure was subjected to laboratory scale composting in order to quantify bioaerosols, i.e., airborne culturable bacteria and endotoxin, in the exhaust gas, which provided details on the effect of temperature on bacterial emissions. The concentration of airborne bacteria reached 31,250 colony-forming units (CFU)/m³ during the thermophilic stage of composting, and positively correlated with the temperature profile of the compost pile. Initially, the endotoxin concentration was 1820 endotoxin units (EU)/m³, but it decreased exponentially as the composting process proceeded. The temperature can be an excellent indicator of bacterial emissions during the composting process, indicating that the composting process requires a consistently high temperature to ensure sanitization of both compost and bacterial emissions. The cumulative emission data showed that emission factors was 11.2?13.5 CFU/g dry swine manure and that of endotoxin was 0.5?0.9 EU/g dry swine manure. The bacterial diversity in the bioaerosol was analyzed by polymerase chain reaction-denaturing gradient gel electrophoresis, revealing the presence of various gram-negative bacterial consortia.     

Evaluation of batch anaerobic co-digestion of palm pressed fiber and cattle manure under mesophilic conditions

Palm pressed fiber (PPF) and cattle manure (CM) are the waste which can be managed properly by anaerobic co-digestion. The biogas production in co-digested PPF and CM at three volatile solids (VS) ratios of 3:1, 1:1, and 1:3 was investigated in a series of batch experiments at an organic loading rate of 30.0 g VS/L under mesophilic (37 ± 1 °C) conditions. The highest daily biogas yield of PPF and CM only, was 90.0 mL/g VS_added at day 12 and 23.4 mL/g VS_added at day 7. For co-digestion of PPF/CM at mixing ratios of 3:1, 1:1 and 1:3, there were 93.6 mL/g VS_added at day 11, 86.8 and 26.4 mL/g VS_added at day 8. VS removal rate for PPF, CM, and co-digestion at mixing ratio of 3:1, 1:1, and 1:3 were 91.1%, 86.0% and 71.0%, respectively. The anaerobic digestion of PPF and CM and their co-digestion systems were stable in operation with low range of volatile fatty acids (VFA)/TIC (total inorganic carbon) of (0.035–0.091). The main volatile fatty acids were propionic, and iso-butyric acids for PPF, iso-butyric and n-butyric acids for CM. The VFAs and ammonium inhibition were not occurred. The modified Gompertz model can be used to perform a better prediction with a lower difference between the measured and predicted biogas yields. A VS ratio of 3:1 is recommended for practice.     

Co-composting rice hulls and/or sawdust with poultry manure in NE Argentina

Rice hulls and sawdust are two common C-rich wastes derived from rice and timber agro-industries in subtropical NE Argentina. An alternative to the current management of these wastes (from bedding to uncontrolled burning) is composting. However, given their C-rich nature and high C/N ratio, adequate composting requires mixing with a N-rich waste, such as poultry manure. The effect of different proportions of poultry manure, rice hulls and/or sawdust on composting efficiency and final compost quality was studied. Five piles were prepared with a 2:1 and 1:1 ratio of sawdust or rice hulls to poultry manure, and 1:1:1 of all three materials (V/V). Different indicators of compost stability and quality were measured. Thermophilic phase was shorter for piles with rice hulls than for piles with sawdust (60 days vs. 105 days). Time required for stability was similar for both C-rich wastes (about 180 days). Characteristics of final composts were: pH 5.8–7.2, electrical conductivity 2.5–3.3 mS/cm, organic C 20–26%, total N 2.2–2.9%, lignin 19–22%, total Ca 18–24 g/kg, and extractable P 6–8 g/kg, the latter representing 60% of total P. Nitrogen conservation was high in all piles, especially in the one containing both C-rich wastes. Piles with sawdust were characterized by high total and available N, while piles with only rice hulls had higher Si, K and pH. Extractable P was higher in 1:1 piles, and organic C in 2:1 piles.     

Evaluation of laboratory-scale in-vessel co-composting of tobacco and apple waste

Efficient composting process requires set of adequate parameters among which physical–chemical properties of the composting substrate play the key-role. Combining different types of biodegradable solid waste it is possible to obtain a substrate eligible to microorganisms in the composting process. In this work the composting of apple and tobacco solid waste mixture (1:7, dry weight) was explored. The aim of the work was to investigate an efficiency of biodegradation of the given mixture and to characterize incurred raw compost. Composting was conducted in 24 L thermally insulated column reactor at airflow rate of 1.1 L min^?1. During 22 days several parameters were closely monitored: temperature and mass of the substrate, volatile solids content, C/N ratio and pH-value of the mixture and oxygen consumption. The composting of the apple and tobacco waste resulted with high degradation of the volatile solids (53.1%). During the experiment 1.76 kg of oxygen was consumed and the C/N ratio of the product was 11.6. The obtained temperature curve was almost a “mirror image” of the oxygen concentration curve while the peak values of the temperature were occurred 9.5 h after the peak oxygen consumption.     

Chemical characterization of emissions from a municipal solid waste treatment plant

Gaseous emissions are an important problem in municipal solid waste (MSW) treatment plants. The sources points of emissions considered in the present work are: fresh compost, mature compost, landfill leaks and leachate ponds. Hydrogen sulphide, ammonia and volatile organic compounds (VOCs) were analysed in the emissions from these sources. Hydrogen sulphide and ammonia were important contributors to the total emission volume. Landfill leaks are significant source points of emissions of H₂S; the average concentration of H₂S in biogas from the landfill leaks is around 1700 ppmv. The fresh composting site was also an important contributor of H₂S to the total emission volume; its concentration varied between 3.2 and 1.7 ppmv and a decrease with time was observed. The mature composting site showed a reduction of H₂S concentration (<0.1 ppmv). Leachate pond showed a low concentration of H₂S (in order of ppbv). Regarding NH₃, composting sites and landfill leaks are notable source points of emissions (composting sites varied around 30–600 ppmv; biogas from landfill leaks varied from 160 to 640 ppmv).Regarding VOCs, the main compounds were: limonene, p-cymene, pinene, cyclohexane, reaching concentrations around 0.2–4.3 ppmv.H₂S/NH₃, limonene/p-cymene, limonene/cyclohexane ratios can be useful for analysing and identifying the emission sources.     

Time domain reflectometry measured moisture content of sewage sludge compost across temperatures

Time domain reflectometry (TDR) is a prospective measurement technology for moisture content of sewage sludge composting material; however, a significant dependence upon temperature has been observed. The objective of this study was to assess the impacts of temperature upon moisture content measurement and determine if TDR could be used to monitor moisture content in sewage sludge compost across a range of temperatures. We also investigated the combined effects of temperature and conductivity on moisture content measurement. The results revealed that the moisture content of composting material could be determined by TDR using coated probes, even when the measured material had a moisture content of 0.581 cm³ cm^?3, temperature of 70 °C and conductivity of 4.32 mS cm^?1. TDR probes were calibrated as a function of dielectric properties that included temperature effects. When the bulk temperature varied from 20 °C to 70 °C, composting material with 0.10–0.70 cm³ cm^?3 moisture content could be measured by TDR using coated probes, and calibrations based on different temperatures minimized the errors.     

Effects of composing on sorption capacity of bagasse-based chars

A fresh bagasse sample (0-month) and two composted bagasse and pig manure mixed samples (1-month and 6-month) were used to produce carbon chars. Sample pyrolysis showed greater carbon char yields were obtained from the compost samples than from the bagasse sample. Fourier transform infrared spectra suggested that the chemical structures of the bagasse sample and the two compost samples were quite different, but that the three carbon chars obtained from those precursors were similar. Among the three pyrolyzed chars, the 0-month bagasse char displayed the largest sorption capacity of 3333 mg kg^?1 for the hydrophilic pollutant phenol, presumably resulting from its greater carbon content and O/C ratio. However, the sorption capacities for the hydrophobic pollutant naphthalene of the tow compost chars (3-month, 2001 mg kg^?1; 6-month, 1667 mg kg^?1) were greater than that of the 0-month bagasse char (1428 mg kg^?1). The results indicate that the compost chars had a greater preferential affinity for naphthalene than that in the bagasse char, suggesting that the compost chars possessed greater hydrophobicity.     

Effects of bulking agent addition on odorous compounds emissions during composting of OFMSW

The effects of rice straw addition level on odorous compounds emissions in a pilot-scale organic fraction of municipal solid waste (OFMSW) composting plant were investigated. The cumulative odorous compounds emissions occurred in a descending order of 40.22, 28.71 and 27.83 mg/dry kg of OFMSW for piles with rice straw addition level at ratio of 1:10, 2:10 and 3:10 (mixing ratio of rice straw to OFMSW on a wet basis), respectively. The mixing ratio of rice straw to OFMSW had a statistically significant effect on the reduction of malodorous sulfur compounds emissions, which had no statistically significant effect on the reduction of VFAs, alcohols, aldehydes, ketones, aromatics and ammonia emissions during composting, respectively. The cumulative emissions of malodorous sulfur compounds from piles with the increasing rice straw addition level were 1.17, 1.08 and 0.88 mg/dry kg of OFMSW, respectively. The optimal mixing ratio of rice straw to OFMSW was 1:5. Using this addition level, the cumulative malodorous sulfur compounds emissions based on the organic matter degradation were the lowest during composting of OFMSW.     

Field scale evaluation of volatile organic compound production inside biosecure swine mortality composts

Emergency mortality composting associated with a disease outbreak has special requirements to reduce the risks of pathogen survival and disease transmission. The most important requirements are to cover mortalities with biosecure barriers and avoid turning compost piles until the pathogens are inactivated. Temperature is the most commonly used parameter for assessing success of a biosecure composting process, but a decline in compost core temperature does not necessarily signify completion of the degradation process. In this study, gas concentrations of volatile organic compounds (VOCs) produced inside biosecure swine mortality composting units filled with six different cover/plant materials were monitored to test the state and completion of the process. Among the 55 compounds identified, dimethyl disulfide, dimethyl trisulfide, and pyrimidine were found to be marker compounds of the process. Temperature at the end of eight weeks was not found as an indicator of swine carcass degradation. However, gas concentrations of the marker compounds at the end of eight weeks were found to be related to carcass degradation. The highest gas concentrations of the marker compounds were measured for the test units with the lowest degradation (highest respiration rates). Dimethyl disulfide was found to be the most robust marker compound as it was detected from all composting units in the eighth week of the trial. Concentration of dimethyl disulfide decreased from a range of 290–4340 ppmv to 6–160 ppbv. Dimethyl trisulfide concentrations decreased to a range of below detection limit to 430 ppbv while pyrimidine concentrations decreased to a range of below detection limit to 13 ppbv.     

Rapid estimation of compost enzymatic activity by spectral analysis method combined with machine learning

The aim of this study was to investigate the feasibility of using visible near-infrared (VisNIR) diffuse reflectance spectroscopy (DRS) as an easy, inexpensive, and rapid method to predict compost enzymatic activity, which traditionally measured by fluorescein diacetate hydrolysis (FDA-HR) assay. Compost samples representative of five different compost facilities were scanned by DRS, and the raw reflectance spectra were preprocessed using seven spectral transformations for predicting compost FDA-HR with six multivariate algorithms. Although principal component analysis for all spectral pretreatments satisfactorily identified the clusters by compost types, it could not separate different FDA contents. Furthermore, the artificial neural network multilayer perceptron (residual prediction deviation = 3.2, validation r² = 0.91 and RMSE = 13.38 μg g^?1 h^?1) outperformed other multivariate models to capture the highly non-linear relationships between compost enzymatic activity and VisNIR reflectance spectra after Savitzky–Golay first derivative pretreatment. This work demonstrates the efficiency of VisNIR DRS for predicting compost enzymatic as well as microbial activity.     

A comparative study of two composts as filter media for the removal of gaseous reduced sulfur compounds (RSCs) by biofiltration: Application at industrial scale

This work presents the use of two composts as filter media for the treatment by biofiltration of odors emitted during the aerobic composting of a mixture containing sewage sludge and yard waste. The chemical analysis of the waste gas showed that the malodorous compounds at trace level were the reduced sulfur compounds (RSCs) which were dimethyl sulfide (Me₂S), methanethiol (MeSH) and hydrogen sulfide (H₂S). Laboratory tests for biofiltration treatment of RSCs were performed in order to compare the properties of two filter media, consisted of a mature compost with yard waste (YW) and a mixture of mature compost with sewage sludge and yard waste (SS/YW). The maximum elimination capacity (EC) values obtained with the YW mature compost as packing material were 12.5 mg m^?3 h^?1 for H₂S, 7.9 mg m^?3 h^?1 for MeSH and 34 mg m^?3 h^?1 for Me₂S, and the removal efficiency decreased in the order of: H₂S > MeSH > Me₂S. Moreover, the YW compost filter medium had a better behavior than the filter medium based on SS/YW in terms of acclimation of the microbial communities and moisture content. According to these results, a YW mature compost as packing material for an industrial biofilter were designed and this industrial biofilter was found effective under specified conditions (without inoculation and addition of water). The results showed that the maximum EC value of RSCs was 935 mg m^?3 h^?1 (100% removal efficiency, RE) for an inlet loads (IL) between 0 and 1000 mg m^?3 h^?1. Thus, YW compost medium was proven efficient for biofiltration of RSCs both at laboratory and industrial scale.     

The effect of dust emissions from open storage piles to particle ambient concentration and human exposure

The current study focus on the determination of dust emissions from piles in open storage yards of a municipal solid waste (MSW) composting site and the subsequent atmospheric dust dispersion. The ISC3-ST (Industrial Source Complex Version 3 – Short Term) model was used for the evaluation of the PM₁₀ ambient concentrations associated with the dispersion of MSW compost dust emissions in air. Dust emission rates were calculated using the United States Environmental Protection Agency proposed dust resuspension formulation from open storage piles using local meteorological data. The dispersion modelling results on the spatial distribution of PM₁₀ source depletion showed that the maximum concentrations were observed at a distance 25–75 m downwind of the piles in the prevailing wind direction. Sensitivity calculations were performed also to reveal the effect of the compost pile height, the friction velocity and the receptor height on the ambient PM₁₀ concentration. It was observed that PM₁₀ concentrations (downwind in the prevailing wind direction) increased with increasing the friction velocity, increasing the pile height (for distances greater than 125 m from the source) and decreasing the receptor height (for distances greater than 125 m from the source). Furthermore, the results of ISC3-ST were analysed with the ExDoM (Exposure Dose Model) human exposure model. The ExDoM is a model for calculating the human exposure and the deposition dose, clearance, and finally retention of aerosol particles in the human respiratory tract (RT). PM₁₀ concentration at the composting site was calculated as the sum of the concentration from compost pile dust resuspension and the background concentration. It was found that the exposure to PM₁₀ and deposited lung dose for an adult Caucasian male who is not working at the composting site is less by 20–74% and 29–84%, respectively, compared to those for a worker exposed to PM concentrations at the composting site.     

Anaerobic co-digestion of food waste and landfill leachate in single-phase batch reactors

In order to investigate the effect of raw leachate on anaerobic digestion of food waste, co-digestions of food waste with raw leachate were carried out. A series of single-phase batch mesophilic (35 ± 1 °C) anaerobic digestions were performed at a food waste concentration of 41.8 g VS/L. The results showed that inhibition of biogas production by volatile fatty acids (VFA) occurred without raw leachate addition. A certain amount of raw leachate in the reactors effectively relieved acidic inhibition caused by VFA accumulation, and the system maintained stable with methane yield of 369–466 mL/g VS. Total ammonia nitrogen introduced into the digestion systems with initial 2000–3000 mgNH₄–N/L not only replenished nitrogen for bacterial growth, but also formed a buffer system with VFA to maintain a delicate biochemical balance between the acidogenic and methanogenic microorganisms. UV spectroscopy and fluorescence excitation–emission matrix spectroscopy data showed that food waste was completely degraded.We concluded that using raw leachate for supplement water addition and pH modifier on anaerobic digestion of food waste was effective. An appropriate fraction of leachate could stimulate methanogenic activity and enhance biogas production.     

Temperature and deactivation of microbial faecal indicators during small scale co-composting of faecal matter

Small scale co-composting of faecal matter from dry toilet systems with shredded plant material and food waste was investigated in respect to heat development and deactivation of faecal indicators under tropical semiarid conditions. Open (uncovered) co-composting of faecal matter with shredded plant material alone did not generate temperatures high enough (<55 °C) to reduce the indicators sufficiently. The addition of food waste and confinement in chambers, built of concrete bricks and wooden boards, improved the composting process significantly. Under these conditions peak temperatures of up to 70 °C were achieved and temperatures above 55 °C were maintained over 2 weeks. This temperature and time is sufficient to comply with international composting regulations. The reduction of Escherichia coli, Enterococcus faecalis and Salmonella senftenberg in test containment systems placed in the core of the compost piles was very efficient, exceeding 5 log₁₀-units in all cases, but recolonisation from the cooler outer layers appeared to interfere with the sanitisation efficiency of the substrate itself. The addition of a stabilisation period by extending the composting process to over 4 months ensured that the load of E. coli was reduced to less than 10³ cfu^?g and salmonella were undetectable.