油页岩循环流化床锅炉底渣和飞灰中重金属元素浸出毒性研究

为了研究我国桦甸油页岩65 t/h循环流化床锅炉的底渣和飞灰中重金属元素Cr、Cu、Pb和Zn的赋存状态及不同酸度条件下的浸出特性,分别进行了逐级提取实验和分批浸出的淋滤实验。逐级提取实验结果表明,这4种元素在底渣和飞灰中具有基本相当的赋存状态。硫化物结合态和稳定的残渣态是各元素的主要赋存状态,元素的潜在浸出能力大小表现为:PbCrCuZn,飞灰中各元素的潜在浸出能力大于底渣中的。浸出实验结果表明,元素的赋存状态决定了其浸提能力,浸提液的pH值对各元素浸出能力的影响不尽相同,各元素的浸出能力随浸提时间的延长都会趋于平衡,Cr和Pb的浸出浓度都高于地表水和饮用水的国家标准。     

Arrested municipal solid waste incinerator fly ash as a source of heavy metals to the UK environment

Arrested fly ash samples from most currently operating municipal solid waste (MSW) incinerators in the UK have been analysed for a range of elements. Some of the more important heavy metals ranged in concentration as follows: Cd, 21-4646 (median = 271) mg kg(-1); Cu, 296-1307 (642) mg kg(-1); Cr, 44-1328 (574) mg kg(-1); Ni, 45-2204 (74) mg kg(-1); Pb, 447-9704 (4337) mg kg(-1); and Zn, 2285-13,500 (9232) mg kg(-1). These concentrations represent considerable enrichments relative to median UK soil concentrations. Enrichment ratios (defined as median fly ash: median UK soil) were as follows: Mn 1.6; Co 2.6; Ni 3.3; Ba 11; Sr 11; Cr 15; Cu 35; Pb 108; Zn 113; Cd 387. It is estimated that MSW incinerator ash contributes c. 15 t Cd and 241 t Pb to UK landfill sites per annum. These figures compare with previous studies by Hutton & Symon (Hutton, M. & Symon, C. (1986). The quantities of cadmium, lead, mercury and arsenic entering the UK environment from human activities. Sci. Total Environ., 57, 129-50.) which estimated that annual inputs to UK landfills from coal fly ash are c. 60 t Cd and 1270 t Pb. However, it is argued that metals associated with MSW ashes are potentially of greater environmental significance than in coal ashes, because they are much more available and present at much higher concentrations.     

Heavy metal leaching from coal fly ash amended container substrates during Syngonium production

Coal fly ash has been proposed to be an alternative to lime amendment and a nutrient source of container substrates for ornamental plant production. A great concern over this proposed beneficial use, however, is the potential contamination of surface and ground water by heavy metals. In this study, three fly ashes collected from Florida, Michigan, and North Carolina and a commercial dolomite were amended in a basal substrate. The formulated substrates were used to produce Syngonium podophyllum Schott 'Berry Allusion' in 15-cm diameter containers in a shaded greenhouse. Leachates from the containers were collected during the entire six months of plant production and analyzed for heavy metal concentrations. There were no detectable As, Cr, Hg, Pb, and Se in the leachates; Cd and Mo were only detected in few leachate samples. The metals constantly detected were Cu, Mn, Ni, and Zn. The total amounts of Cu, Mn, Ni, and Zn leached during the six-month production period were 95, 210, 44, and 337 microg per container, indicating that such amounts in leachates may contribute little to contamination of surface and ground water. In addition, plant growth indices and fresh and dry weights of S. podophyllum 'Berry Allusion' produced from fly ash and dolomite-amended substrates were comparable except for the plants produced from the substrate amended with fly ash collected from Michigan which had reduced growth indices and fresh and dry weights. Thus, selected fly ashes can be alternatives to commercial dolomites as amendments to container substrates for ornamental plant production. The use of fly ashes as container substrate amendments should represent a new market for the beneficial use of this coal combustion byproduct.     

Leaching characteristics of stabilized/solidified fly ash generated from ash-melting plant

This study was designed to elucidate the leaching characteristics of stabilized/solidified (S/S) fly ash generated by ash-melting. For this study, pH-dependent leaching tests, sequential extraction procedures, and column leaching tests were carried out. The pH-dependent leaching test results for Pb, Cu, and Zn showed that the heavy metal concentrations in the high-pH range were lower than the predicted values for hydroxide and carbonate. During sequential extraction, Cu and Pb were principally distributed in the S/S ashes' organic matter fraction in the chelating agent, suggesting that metals bind to the chelating agent. The percentage of the water-soluble fraction for Pb and Cu was low (<0.2 %). The fly ashes treated with a chelating agent and cement had low leachability potential for metals in the high-pH range. Column tests for S/S fly ashes showed that two leaching stages were distinguishable: one for short time, corresponding to faster metal leaching, and another for the leaching rate. Kinetic speciation was then applied to data obtained from column leaching tests. The first-order reaction/diffusion model showed a better fit for Ca, Pb, and Cu, suggesting that the initial dissolution of soluble compounds, such as metal chloride, was controlled by the first-order reaction (surface wash off). Subsequently, insoluble compounds such as hydroxide or carbonate might penetrate into the porous matrix by diffusion.     

Edaphological characteristics of unweathered and weathered fly ashes from Gondwana and lignite coal

Naturally weathered and unweathered samples of fly ashes produced from Gondwana and lignite coals were characterized for their edaphological properties. The particle size distribution in these fly ashes varied widely, and the percentage of [Formula: see text] size particles governed their water holding capacity. All fly ashes were noncoherent in the dry state and had lower particle density than quartz and mulite. The fly ashes were low in available N, but were sufficient in available P, K, Ca, Mg, S, Cu, Fe, Mn, Zn and B. Among the fly ashes, unweathered lignite fly ash was the richest source of K, Ca, Mg, S and Fe, while weathered lignite fly ash had the highest amounts of Mn, Zn and B. The pH of the fly ashes was closely related to the ratio of exchangeable Ca to exchangeable Al. The fly ashes were high in soluble salt, but were poor in cation exchange capacity. As an amendment to correct soil pH, the fly ashes had a poor buffering capacity. Weathering decreased the total Fe, available S and exchangeable Na percentages, but increased the organic C content of the fly ashes. Invariably, an excess of soluble salts and exchangeable Na could limit plant growth on fly ash dumps. Toxic levels of B and Al existed in only some fly ashes.     

SGA对垃圾焚烧飞灰中重金属的固化性能研究

根据EPA1311、HJ／T299—2007、HJ／T300—2007和HJ557—2009等国内外不同标准，研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性，探讨了六硫代胍基甲酸（sixthioguanidineacid，SGA）、二甲基二硫代氨基甲酸盐（sodiumdimethyldithiocarbamate，SDD）和Ca（OH）2浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明，随着浸提液pH的降低，该厂焚烧飞灰中大部分金属元素的浸出量增大，焚烧飞灰浸出液中的cd、Ni、Ph和zn浓度分别超过国家危险废物鉴别标准（GB5085．3—2007）规定值的4．75倍、1．47倍、6．72倍和2．20倍，属于危险废弃物，必须进行稳定化处理。当固化剂SGA加入量为0．1mol／kg时，稳定化后的重金属浸出浓度已经低于危险废物鉴别标准，且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）2；当固化剂SGA、SDD和Ca（OH）2加入量为0．5mol／kg时，稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB5085．3-2007）中的规定值。与SDD和Ca（OH）：相比，SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

Removal of heavy metals from anaerobically digested sewage sludge by isolated indigenous iron-oxidizing bacteria

The removal of heavy metals (Cr, Cu, Zn, Ni and Pb) from anaerobically digested sludge from the Yuen Long wastewater treatment plant, Hong Kong, has been studied in a batch system using isolated indigenous iron-oxidizing bacteria. The inoculation of indigenous iron-oxidizing bacteria and the addition of FeSO4 accelerated the solubilization of Cr, Cu, Zn, Ni and Pb from the sludge. pH of the sludge decreased with an increase in Fe2+ concentrations and reached a low pH of 2-2.5 for treatments receiving both bacterial inoculation and FeSO4. After 16 days of bioleaching, the following heavy metal removal efficiencies were obtained: Cr 55.3%, Cu 91.5%, Zn 83.3%, Ni 54.4%, and Pb 16.2%. In contrast, only 2.6% of Cr, 42.9% of Cu, 72.1% of Zn, 22.8% of Ni and 0.56% of Pb were extracted from the control without the bacterial inoculation and addition of FeSO4. The residual heavy metal content in the leached sludge was acceptable for unrestricted use for agriculture. The experimental results confirmed the effectiveness of using the isolated iron-oxidizing bacteria for the removal of heavy metals from sewage sludge.     

Emission of heavy metals from animal carcass incinerators in Taiwan

The metal emissions from three incinerators burning different feedstock in Taiwan were characterized in this study. It was found that the Incinerators A and B, treating pig carcasses and animal (including pigs) carcasses, respectively, had much higher metal concentrations in stack flue gases than Incinerator C that combusted medical wastes. However, Incinerator A obtained relative lower metal contents in fly ash and bottom ash than the other two incinerators, mainly because the former used a much lower feedstock rate (although burning at a lower temperature) than the latter. For all the incinerators, (1) Fe, Ni, Pb, and Zn were dominant in both the fly ash and bottom ash while most of the Cd and Pb (more volatile) were present in the fly ash; (2) Fe emission factor was the highest and Zn/Pb/Ni/Cr emission factors were greater than those of Mn/Cd/Cu; (3) the Cu emission factors in bottom ash were relatively higher in comparison with those in fly ash; and (4) indicatory metals were the same (Fe, Zn, Pb, and Cu). The metal emission factors obtained from the livestock incinerators were much higher than those reported from MSW incinerators. Likewise, crematories that burn human cadavers must create similar pollution issues since metal supplements are part of human's normal diets. This causes an environmental concern and this work has important ramifications both in technical and regulatory decisions.     

水泥对垃圾焚烧飞灰的固化处理试验研究

对垃圾焚烧飞灰的化学成分、重金属物质的含量及浸出浓度进行测试分析.结果表明,飞灰中Pb和Cr等重金属物质浸出量超过浸出毒性标准,因而被认为是危险废物,必须进行固化处理.还考察了水泥对焚烧飞灰中重金属物质固化的效果,研究表明当飞灰掺量适当时,重金属物质的固化效果良好.重金属物质通过物理固封、替代,沉淀反应和吸附等形式可固化进水泥水化产物结构中.     

SGA对垃圾焚烧飞灰中重金属的固化性能研究简

根据EPA 1311、HJ/T 299-2007、HJ/T 300-2007和HJ 557-2009等国内外不同标准，研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性，探讨了六硫代胍基甲酸（sixthio guanidine acid，SGA）、二甲基二硫代氨基甲酸盐（sodium dimethyl dithio carbamate，SDD）和Ca（OH）₂浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明，随着浸提液pH的降低，该厂焚烧飞灰中大部分金属元素的浸出量增大，焚烧飞灰浸出液中的Cd、Ni、Pb和Zn浓度分别超过国家危险废物鉴别标准（GB5085.3-2007）规定值的4.75倍、1.47倍、6.72倍和2.20倍，属于危险废弃物，必须进行稳定化处理。当固化剂SGA加入量为0.1 mol/kg时，稳定化后的重金属浸出浓度已经低于危险废物鉴别标准，且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）₂；当固化剂SGA、SDD和Ca（OH）₂加入量为0.5 mol/kg时，稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB 5085.3-2007）中的规定值。与SDD和Ca（OH）₂相比，SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

城市生活垃圾焚烧处理过程中重金属迁移规律研究

通过采集厦门2个垃圾焚烧发电厂进厂垃圾、渗滤液、飞灰、炉渣和烟气样品，分析垃圾组成成分及各组分的重金属含量，结果表明，垃圾中以厨余、橡塑类和纸类为主，共占到垃圾干基的78．08％，重金属含量大小次序为Zn〉Cu〉Pb〉Cr〉Ni〉Cd〉Hg；垃圾渗滤液中除Zn外，其他金属的含量都较低，一厂渗滤液中重金属Ni、Zn迁移量较大，分别达到24．46％和8．52％。二厂渗滤液中重金属的迁移有相同的趋势，但含量相对较高。垃圾焚烧后其重金属主要分布在飞灰和废渣中，烟气中的含量非常少，不同金属的含量均有差别，这与金属的性质有很大关系；通过浸出毒性分析，飞灰中重金属酸溶态含量多，容易浸出，属于危险废物。同时，不同烟气处理工艺产生的飞灰的重金属浸出量有很大差别。     

Influence of solution acidity and CaCl2 concentration on the removal of heavy metals from metal-contaminated rice soils

Soil washing is considered a useful technique for remediating metal-contaminated soils. This study examined the release edges of Cd, Zn, Ni, Cr, Cu or Pb in two contaminated rice soils from central Taiwan. The concentrations exceeding the trigger levels established by the regulatory agency of Taiwan were Cu, Zn, Ni and Cr for the Ho-Mei soil and Pb for the Nan-Tou soil. Successive extractions with HCl ranging from 0 to 0.2 M showed increased release of the heavy metals with declining pH, and the threshold pH value below which a sharp increase in the releases of the heavy metals was highest for Cd, Zn, and Ni (pH 4.6 to 4.9), intermediate for Pb and Cu (3.1 to 3.8) and lowest for Fe (2.1), Al (2.2) and Cr (1.7) for the soils. The low response slope of Ni and Cr particularly for the rice soils make soil washing with the acid up to the highest concentration used ineffective to reduce their concentrations to below trigger levels. Although soil washing with 0.1 M HCl was moderately effective in reducing Cu, Pb, Zn and Cd, which brought pH of the soils to 1.1+/-0.1 (S.D.), the concurrent release of large quantities of Fe and Al make this remediation technique undesirable for the rice soils containing high clay. Successive washings with 0.01 M HCl could be considered an alternative as the dissolution of Fe and Al was minimal, and between 46 to 64% of Cd, Zn, and Cu for the Ho-Mei soil and 45% of Pb in the Na-Tou soil were extracted after four successive extractions with this dilute acid solution. The efficacy of Cd extraction improved if CaCl2 was added to the acid solution. The correlation analysis revealed that Cr extracted was highly correlated (P < 0.001) with Fe extracted, whereas the Cu, Ni, Zn, Cd or Pb extracted was better correlated (P < 0.001) with Al than with Fe extracted. It is possible that the past seasonal soil flooding and drainage in the soils for rice production was conducive to incorporating Cr within the structure of Fe oxide, thereby making them extremely insoluble even in 0.2 M HCl solution. The formation of solid solution of Ni with Al oxide was also possible, making it far less extractable than Cd, Zn, Cu, or Pb with the acid concentrations used.     

An ultrasonic assisted extraction method to release heavy metals from untreated sewage sludge samples

A rapid ultrasound accelerated sequential extraction procedure has been used to develop sequential extraction proposed by BCR protocol (the community Bureau of Reference now the European Union "Measurement and Testing Programme"). The effects of the ultrasonic treatment on the extraction of Cu, Cd, Cr, Pb, Ni and Zn from untreated sewage sludge collected from industrial site of Hyderabad city (Pakistan) were compared with those obtained from conventional sequentional extraction procedure of modified BCR protocol. In BCR method, each extraction steps takes 10h, where as with the use of compromise sonication conditions in ultrasonic bath, steps 1-3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 30, 30 and 30 min, respectively. Extractable Cd, Cr, Pb and Ni contents were obtained by both comparable methodologies were measured by electrothermal atomic absorption spectrometry (ETAAS), while for Cu and Zn Flame atomic absorption spectrometry (FAAS) was used. The validations of both methods were compared by the analysis of certified reference material of soil amended with sewage sludge (BCR 483). According to statistical evaluation of the results, the proposed accelerated extraction method is valid alternative to conventional shaking with much shorter extraction time with p value <0.05. The overall metal recoveries in steps 1-3 (excluding residual step) were 95-100% of those obtained with the conventional BCR protocol, except for Cu extracted (91.6%) as related to indicative values of Cu in BCR 483 obtained in 1-3 steps. The results of the partitioning study of untreated industrial waste water sewage sludge, indicate that more easily mobilized forms (acid exchangeable) were predominant for Cd and Zn, in contrast, the largest amount of Pb and Cr was associated with the iron/manganese oxide and organic matter/sulphide fractions.     

Stabilisation of MSWI bottom ash with sulphide-rich anaerobic effluent

Effluent of an anaerobic sulphate-reducing wastewater treatment process was used to stabilise bottom ash. The effect of stabilisation on the concentration and binding of Ca, P, S, Cu, Pb, Zn, As, Cr, and Mo were studied by comparing results of sequential extraction from fresh and stabilised bottom ash. The stabilisation treatment improved the retention of Ca, Cu, Pb, S, and Zn in bottom ash compared to a treatment with ion-exchanged water. In addition to retention, Cu, S, and Zn were accumulated from the anaerobic effluent in the bottom ash. Concentrations of As, Cr, and Mo remained on the same level, whereas leaching of P increased compared to control treatment with ion-exchanged water. Improved retention and accumulation were the result of increased binding to less soluble fractions. The highest increases were in the sulphide and organic carbon bound fraction and in the carbonate fraction. Enhanced carbonation was probably due to CO2 deriving from the degradation of organic carbon. Flushing of stabilised bottom ash with ion-exchanged water ensured that the observed changes were not easily reversed. Most of the sulphide in the anaerobic effluent was removed when it was passed through bottom ash. The objective was to study the feasibility of sulphide-rich anaerobic effluent in bottom ash stabilisation and changes in the binding of the elements during stabilisation. In addition, the ability of the process to remove sulphide from the effluent was observed.     

高温堆肥与蚯蚓堆肥对城市污泥重金属形态的影响

采用高温堆肥和蚯蚓堆肥工艺，研究了城市污泥与锯末、粉煤灰或磷矿粉按不同比例混合堆肥前后重金属（Cu、Pb、Zn、Cd和As）交换态、碳酸盐结合态、铁锰氧化物结合态、有机结合态和残留态的变化。研究表明：高温堆肥和蚯蚓堆肥前后各试验污泥的重金属形态和含量呈现出不同的变化，都可以降低污泥中交换态Cu、Pb、Zn、Cd和As的含量；对于Cu和Pb，高温堆肥优于蚯蚓堆肥；对于Zn、Cd和As，蚯蚓堆肥优于高温堆肥。2种堆肥方式中，粉煤灰用量为10%的钝化效果优于20%，磷矿粉的钝化效果同粉煤灰一样。     

Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

Element distribution in a combined fly ash and bottom ash from combustion of copper chromate arsenate (CCA) treated wood waste was investigated by scanning electron microscopy (SEM/EDX) before and after electrodialytic extraction. The untreated ash contained various particles, including pieces of incompletely combusted wood rich in Cr and Ca, and irregular particles rich in Si, Al and K. Cr was also found incorporated in silica-based matrix particles. As was associated with Ca in porous (char) particles, indicating that Ca-arsenates had been formed during combustion. Cu was associated with Cr in the incompletely combusted wood pieces and was also found in almost pure form in a surface layer of some matrix particles - indicating surface condensation of volatile Cu species. In treated ash, Ca and As were no longer found together, indicating that Ca-arsenates had been dissolved due to the electrodialytic treatment. Instead particles rich in Ca and S were now found, indicating precipitation of Ca-sulphates due to addition of sulphuric acid in connection with the electrodialytic treatment. Cu and Cr were still found associated with incompletely combusted wood particles and incorporated in matrix particles. Chemical analyses of untreated and treated ash confirmed that most As, but only smaller amounts of Cu and Cr was removed due to the electrodialytic extraction. Overall metal contents in the original ash residue were: 1.4 g As, 2.76 g Cu and 2.48 g Cr, after electrodialytic extraction these amounts were reduced by 86% for As, 15% for Cu and 33% for Cr.     

Heavy metal levels and solid phase speciation in street dusts of Delhi,India

Street dust samples were collected from three different localities (industrial, heavy traffic and rural) situated in the greater Delhi area of India. The samples analyzed for Cd, Zn, Pb, Ni, Cu, and Cr indicated remarkably high levels of Cr, Ni, and Cu in the industrial area, whilst Pb and Cd did not show any discernible variations between the three localities. A multivariate statistical approach (Principal Component Analysis) was used to define the possible origin of metals in dusts. The street dusts were sequentially extracted so that the solid pools of Cd, Zn, Pb, Ni, Cu, Cr could be partitioned into five operationally defined fractions viz. exchangeable, bound to carbonates, bound to Fe-Mn oxides, bound to organic matter and residual. Metal recoveries in sequential extractions were +/- 10% of the independently measured total metal concentrations. Cd was the only metal present appreciably (27.16%) in the exchangeable fraction and Cu was the only metal predominantly associated (44.26%) with organic fraction. Zn (45.64%) and Pb (28.26%) were present mainly in the Fe-Mn oxide fraction and the residual fraction was the most dominant solid phase pool of Cr (88.12%) and Ni (70.94%). Assuming that the mobility and bioavailability are related to the solubility of geochemical forms of the metals and decrease in order of extraction, the apparent mobility and potential metal bioavailability for these highly contaminated street dust samples is: Cd>Zn approximately equal Pb>Ni>Cu>Cr.     

Remediation of metal-contaminated soils with the addition of materials - part II: leaching tests to evaluate the efficiency of materials in the remediation of contaminated soils

The effect of the addition of materials on the leaching pattern of As and metals (Cu, Zn, Ni, Pb, and Cd) in two contaminated soils was investigated. The examined materials included bentonites, silicates and industrial wastes, such as sugar foam, fly ashes and a material originated from the zeolitization of fly ash. Soil + material mixtures were prepared at 10% doses. Changes in the acid neutralization capacity, crystalline phases and contaminant leaching over a wide range of pHs were examined by using pH_stat leaching tests. Sugar foam, the zeolitic material and MX-80 bentonite produced the greatest decrease in the leaching of pollutants due to an increase in the pH and/or the sorption capacity in the resulting mixture. This finding suggests that soil remediation may be a feasible option for the reuse of non-hazardous wastes.     

Metal contamination and solid phase partitioning of metals in urban roadside sediments

This study was undertaken to assess the anthropogenic impact on metal concentrations of urban roadside sediments (N = 633) in Seoul city, Korea and to estimate the potential mobility of selected metals (Zn, Cu, Pb, Cr, Ni, and Cd) using sequential extraction. Comparison of metal concentrations in roadside sediments with mean background values in sediments collected from first- or second-order streams in Korea shows that Zn, Cu and Pb are most affected by anthropogenic inputs. The 206Pb/207Pb ratios of roadside sediments (range = 1.1419-1.1681; mean 1.1576 +/- 0.0068) suggest that Pb is mainly derived from industrial sources rather than from leaded gasoline. A five-step sequential extraction of roadside sediments showed that Zn, Cd and to a lesser degree Ni occur predominantly in the carbonate bound fraction, while Pb is highest in the reducible fraction, Cu in the organic fraction, and Cr in the residual fraction. It was found that the concentrations in the readily available exchangeable fraction were generally low for most metals examined, except for Ni whose exchangeable fraction was appreciable (average 15.2%). Considering the proportion of metals bound to the exchangeable and carbonate fractions, the comparative mobility of metals probably decreases in the order of Zn > Ni > Cd > Pb > Cu > Cr. As potential changes of redox state and pH may remobilize the metals bound to carbonates, reducible, and/or organic matter, and may release and flush them through drain networks into streams, careful monitoring of environmental conditions appears to be very important. With respect to ecotoxicity, it is apparent the Zn and Cu pollution is of particular concern in Seoul city.     

Bioleaching of metal from municipal waste incineration fly ash using a mixed culture of sulfur-oxidizing and iron-oxidizing bacteria

We investigated the behavior and characteristics of metal leaching from municipal solid waste incineration (MSWI) fly ash among pure cultures of a sulfur-oxidizing bacterium (SOB) and an iron-oxidizing bacterium (IOB) and a mixed culture. The IOB has a high metal-leaching ability, though its tolerability against the ash addition is low. The SOB might better tolerate an increase in ash addition than the IOB, though metal leaching ability of the SOB is limited. Mixed culture could compensate for these deficiencies, and high metal leachability was exhibited in the 1% ash culture, i.e., 67% and 78% of leachabilities for Cu and Zn, respectively, and 100% for Cr and Cd. Furthermore, comparably high leachabilities such as 42% and 78% for Cu and Zn were observed even in the 3% ash cultures. Characterization of metal leaching by the mixed culture revealed that the acidic and oxidizing condition had remained stable thorough the experimental period. Ferric iron remained in the mixed culture, and the metal leaching was enhanced by redox mechanisms coupling with the leaching by sulfate. An increase of ferrous iron enhanced the Cr, Cu, and As leaching. The optimum concentration of sulfur existed for As and Cr (5 gl(-1)) and Cu (2 gl(-1)). The presence of the degradable and non-degradable organic compound that must be existed in the natural environment or waste landfills made no significant change in the leachability of metals other than Zn. These results suggested that bioleaching using a mixed culture of SOB and IOB is a promising technology for recovering the valuable metals from MSWI fly ash.