临兴致密砂岩气压裂返排液再利用技术

针对临兴区块致密砂岩气井压裂返排液的性能特点,结合压裂返排液中的有害指标,制定了压裂返排液复配压裂液的水质标准,形成了一套压裂返排液经适度处理后复配压裂液的低成本处理模式。结果表明:临兴区块压裂液配置水指标应满足pH值7～10、矿化度60 000mg/L、钙离子浓度600mg/L、镁离子浓度900mg/L、硼离子浓度10mg/L;经过破胶、pH值调整、絮凝和过滤工艺处理后的压裂返排液的主要有害指标COD、钙离子、镁离子、硼离子浓度大幅度下降,满足临兴区块压裂液配置水指标要求;根据处理工艺研制的压裂返排液处理装置在临兴区块LX-*1井和LX-*2井成功完成现场实验,复配压裂液满足压裂液现场施工要求。     

酸洗作业对三元复合驱采出液油水分离特性的影响

采用现场三元复合驱采出液,以及室内制备的模拟采出液和采出液为介质,研究了酸洗液添加剂和酸洗作业油井投产初期产出水中的沉淀物形成离子对北二西试验区三元复合驱采出液油水分离特性的影响,确定井筒酸洗作业油井投产初期产出液造成北二西试验区三元复合驱采出液油水分离效果恶化的主要原因是其水相中含有大量Fe2+,其与地面掺水中的S2-作用产生硫化亚铁微粒,后者吸附在油珠表面上形成阻碍油珠间相互聚并的空间位阻。     

气田压裂返排液回用影响因素研究

针对气田压裂返排液回用配制压裂液的水质要求,研究了pH值、金属离子、细菌和泡沫对处理后液体配制压裂液的影响。结果表明,通过调节pH值、控制金属离子浓度、加入杀菌剂和消泡剂可以达到回用配制压裂液的要求。其中,pH值应控制在6.5左右;当Na2CO3和NaOH的复配比为800/600、NaOH投加量为300mg/L时,能有效去除Ca2+、Mg2+、Fe3+等离子的影响;杀菌剂采用气田压裂专用杀菌剂;消泡剂采用二甲基硅油。实验在气井井场采用撬装微涡流混凝装置处理气田压裂返排液,并对上清液回用配液,回用率达到98.4%。     

让纳若尔油田采出水处理汽提脱硫阻垢技术

让纳若尔油田采出水处理汽提脱硫工艺,高温工况下结垢严重,筛选合适的阻垢剂并对其进行应用评价,使脱硫塔达到良好的运行效果。文章分析了汽提脱硫装置结垢原因,进行了常规阻垢剂筛选评价、新型合成阻垢剂性能评价、化学平衡防垢技术的研究。结果表明：现场试运行实验投加有机复合酸离子调整剂A40mg／L、新型合成阻垢剂G－3为30mg／L,作为适合本工程的阻垢剂。     

臭氧气浮／微涡流絮凝分级处理含聚采出水

含聚合物采出水的有效处理和达标回注是解决油田环保风险和生产压力的关键问题。文章通过对长庆油田陇东区域某试验站的采出水水质进行调研和评价,发现处理后的含聚采出水平均悬浮固体含量高达102.5mg/L,无法达到Q/SY CQ 08011—2019《陇东油田采出水处理水质指标及分析方法》中规定的悬浮物≤50mg/L的回注标准。针对上述问题,分析了聚合物分子量及浓度对悬浮物去除的影响,根据聚合物含量提出不同的采出水处理工艺：针对聚合物浓度≥50mg/L的,形成高含聚合物废水的臭氧气浮处理技术,聚合物降解效率≥60％;针对聚合物浓度＜50mg/L的,形成了微涡流絮凝固液分离技术;在最佳搅拌条件和加药量下,处理后聚合物浓度≤10mg/L,悬浮物含量≤25mg/L,可达到 Q/SY CQ 08011—2019的回注标准。研究成果可以为后续开展含聚采出水现场治理提供技术支撑。     

蓄热式氧化技术在火驱烟道气处理中的应用

以红山嘴油田红浅1井区火驱先导试验烟道气处理为例,火驱烟道气中非甲烷总烃(NMHC)含量及H_2S浓度无法满足GB 16297—1996《大气污染物综合排放标准》、GB 14554—1993《恶臭污染物排放标准》,必须对此进行处理。文章对比分析了常用处理工艺技术特点,提出蓄热式氧化工艺处理烟道气具有对NMHC、H_2S、CO等摧毁效率高;对火驱低热值含硫采出气处理负荷调节范围大,处理后烟气满足环保排放标准等技术优势;经过矿场试验,验证了热氧化工艺处理含H2S低浓度烷烃气体的可行性,处理后的气体满足上述标准排放要求,为后续火驱开发提供了技术支持,具有一定的应用价值。     

一体化采出水处理装置研究及应用

长庆油田采出水处理站具有点多面广的特点.为满足油田低成本开发的需求,研发了一体化采出水处理装置,该装置具有橇装化、集成化、自动化和数字化等特点.现场应用结果表明：经该装置处理后水质达标.处理过程不投加药剂、运行费用低、污泥产生量少,现场管理方便,适合边远中小型站场采出水处理.     

破乳剂对化学驱采出液的作用规律

研究了破乳剂对化学驱采出液体系微观结构以及油水界面性质的影响,观测了不同浓度破乳剂加入前后采出液体系中分散相水滴粒径变化,并通过比较破乳剂对乳状液脱水率以及油水界面性质的影响,探讨了破乳剂对化学驱采出液的作用机理。实验结果表明:破乳剂能加快水滴聚并进程,使分散相水滴聚并明显,而破乳剂对这一过程影响的关键在于对乳状液油水界面剪切黏度的改变。     

强碱三元复合驱采出水处理工艺技术研究

常规的"沉降+过滤"方式用于三元复合驱采出水处理,聚合物或黏度对石油类和SS的高效去除有较大影响,处理思路应以脱稳降黏为主。文章探索了采用的"气浮沉降+生化氧化+高级氧化+二级过滤"工艺,达到石油类≤800 mg/L,SS≤350 mg/L,黏度≤12 mPa·s,PAM≤800 mg/L,使采出水处理稳定达到回注水要求,降低滤池冲洗难度,降低了固液分离难度,提高了工艺运行稳定性。对于采出水进一步开展膜深度处理,采出水实现回注低渗透层等具有重要意义。     

含油废水处理工艺优化研究

在已开发的含油废水处理装置的基础上,对其整体结构、旋分分离部分进行改进,并筛选出性能优良的填料。将原处理装置的单向旋分器改进为双向旋分器、采用YS填料之后,对石油类浓度低于400mg/L的含油废水,经该装置处理后,石油类的去除率达到90%以上;石油类浓度低于80mg/L的含油废水,经该装置处理后,石油类的去除率达95%,石油类的浓度小于10mg/L,达到国家《污水综合排放标准》(GB8798-1996)二级标准的要求。改进后的装置对高、中、低不同浓度石油类的含油废水均有较好的处理效果。     

高含氯采油废水生物治理技术研究

采用SBR活性污泥法,选用从海水、采油废水及长期受原油污染的土壤中筛选的耐盐有机物优势降解菌来处理高含氯采油废水。现场中试试验证明:在氯离子浓度小于10000 mg/L时,用该法可使处理后的高含氯采油废水达标排放。研究表明,解决高含氯采油废水生物治理的前提是驯化具有良好有机物降解性能的耐盐微生物。     

SEMIPERMEABLE MEMBRANE DEVICES USED TO ESTIMATE BIOCONCENTRATION OF POLYCHLORINATED BIPHENYLS1

ABSTRACT: Aquatic organisms passively accumulate hydrophobic organic compounds, such as polychlorinated biphenyls, even when ambient water concentrations of the contaminant are below analytical detection limits. However, contaminant concentrations in tissue samples are subject to an inherently high level of variability due to differences in species, life stage, and gender bioconcentration potentials. Semipermeable membrane devices (SPMDs) were used to sample Aroclor 1254, a mixture of readily bioconcentrated polychlorinated biphenyls (PCBs), in a contaminated wetland near Flat Top, WV. The devices consisted of triolein, a lipid found in fish, enclosed in a polyethylene membrane. SPMDs were deployed in the water column and in direct contact with wetland sediments along a previously identified concentration gradient of PCBs. The devices were retrieved after a 25-day exposure period. Analytes were recovered by dialyzing the devices in nanograde hexane. Hexane dialysates were condensed and analyzed by gas chromatography. All deployed devices sequestered quantifiable amounts of Aroclor 1254. Water-column SPMDs accumulated PCBs far in excess of ambient water concentrations. The devices contacting sediments accumulated PCBs at all sites, though accumulated concentrations did not exceed concentrations in sediment. Patterns of PCB concentration in the devices corresponded to the identified gradient at the site. Results from the water-column SPMDs were used to estimate the concentration of the dissolved, bioavailable fraction of PCBs present in the water column. These concentrations ranged from 0.01 to 0.09 μg/L of bioavailable Aroclor 1254.     

QUALITY STUDY OF GRAYWATER TREATMENT SYSTEMS1

ABSTRACT: A residential single family dwelling was retrofitted to recycle graywater for landscape irrigation and toilet flushing. The objective of this study was to determine improvements in graywater quality by evaluating five simple graywater treatment systems that were easily adapted to the household plumbing. The treatment systems consisted of (1) water hyacinths and sand filtration, (2) water hyacinths, copper ion disinfection, and sand filtration, (3) copper ion disinfection and sand filtration, (4) copper/silver ion disinfection and sand filtration, and (5) 20–μm cartridge filtration. Water quality parameters measured were fecal and total coliform indicator bacteria, nitrates, suspended solids, and turbidity. Reductions in bacterial concentration, suspended solids and turbidity were achieved by all systems tested. Treatment reduced nitrate concentrations to an average of 2.6 mg/liter. Reductions in suspended solids, and turbidity were influenced more by the quality of the graywater entering the treatment system than the efficiency of the systems themselves. The water hyacinths and sand filtration system provided the best graywater quality in terms of the concentrations of fecal indicator bacteria. The system providing the best water quality in regard to average suspended solids after treatment was the water hyacinths, copper ion, and sand filtration system, and the best average turbidity was achieved by the copper/silver ion generating unit with sand filtration. All systems were capable of significant reductions in fecal indicator bacteria, suspended solids, and turbidity; however, additional treatment or disinfection would be necessary to further reduce the level of coliform and fecal coliform bacteria to achieve regulatory standards in the State of Arizona.     

适用于弱碱性条件下使用的防垢剂研究

在防垢剂防垢性能测评中,对适于弱碱性条件下的防垢剂进行了实验研究。研究结果表明,在pH值为8时,有机膦酸、膦羧酸类防垢剂均具有很好的防垢性能;加入量为5mg/L时,对碳酸钙的防垢率可达95%以上。在pH值为9时,复配防垢剂有较好的防垢效果。例如FG-01与HPAA按1∶1复配后,加入量为5mg/L时,防垢率可达71.3%;加入量为10mg/L时,防垢率可达78.1%。     

Application of cavitational reactors for water disinfection: current status and path forward

Cavitational reactors are a novel and promising form of multiphase reactors, based on the principle of release of large magnitude of energy due to the violent collapse of the cavities. An overview of cavitational reactors in the specific area of water disinfection, in terms of the basic mechanism, different reactor designs including recommendations for optimum operating parameters and applicability of the cavitation phenomena for disinfection of different micro-organisms have been presented. A design of a pilot scale sonochemical reactor has been presented, which forms the basis for development of industrial scale reactors. Economic analysis for comparison of cavitation phenomena with other conventional techniques of disinfection has been discussed. It appears that though cavitation is quite successful in treatment of water at laboratory scale operations, comparatively higher cost of treatment as compared to the conventional chemical methods is a hindrance in its industrial scale application. Intensification of cavitational activity and efficient design of industrial scale hydrodynamic cavitation reactors is required for ensuring successful application of cavitational reactors at industrial scale operation.     

Biosorption of Cu and Zn from aqueous solutions by dried marine green macroalga Chaetomorpha linum

The biosorption of the heavy metals Cu²⁺ and Zn²⁺ by dried marine green macroalga (Chaetomorpha linum) was investigated. The biosorption capacities of the dried alga for copper and zinc were studied at different solution pH values (2–6), different algal particle sizes (100–800 μm) and different initial metal solution concentrations (0.5–10 mM). An optimum pH value of 5 was found suitable for both metal ions biosorption for both metal ions. At the optimum particle size (100–315 μm), biosorbent dosage (20 g/l) and initial solution pH (pH 5), the dried alga produced maximum copper and zinc uptakes values (q_max) of 1.46 and 1.97 mmol/g respectively (according to the Langmuir model). The kinetic data obtained at different initial metal concentrations indicated that the biosorption rate was fast and most of the process was completed within 120 min. This study illustrated an alternative technique for the management of unwanted biological materials using processed algal material. C. linum is one of the fast-growing marine algae in the lake of Tunis and could be utilized as a biosorbent for the treatment of Cu²⁺ and Zn²⁺ contaminated wastewater streams.     

Preceding crop affects grain cadmium and zinc of wheat grown in saline soils of central Iran

Enhanced Cd concentrations in wheat (Triticum aestivum L.) grain produced on saline soils of central Iran have been recently reported. Because wheat bread is a major dietary component for the Iranian people, practical approaches to decrease Cd concentration in wheat grain were investigated. This study investigated the influence of sunflower-wheat vs. cotton-wheat rotations on extractable Cd and on Cd uptake by wheat in these salt-affected soils. Two fields with different levels of Cd contamination (1.5 and 3.2 mg total Cd kg(-1) dry soil) were cropped with different rotations (cotton-wheat and sunflower-wheat) in Qom province, central Iran. Seeds of cotton (Gossypium L.) or sunflower (Helianthus annuus L. cv. Record) were planted in plots. After harvesting of the plants and removal of crop residues, wheat (cv. Rushan) was seeded in all plots. For both studied soils, the concentrations of Cd extracted by 0.04 M EDTA and 1 M CaCl(2) were significantly (P < or = 0.05) greater after cotton than after sunflower. Accordingly, the total amount of Cd in sunflower shoot was significantly (P < or = 0.05) greater than in the cotton shoot. Shoot Cd content in wheat plants grown after cotton and sunflower were significantly different; wheat shoots after cotton accumulated more Cd (two to four times) than after sunflower. Wheat grain Cd concentration after sunflower was much lower (more than seven times) than after cotton. The results of this study showed that sunflower in rotation with wheat in salt-affected soils of central Iran significantly reduced the risk of Cd transfer to wheat grain.     

Optimizing phosphorus characterization in animal manures by solution phosphorus-31 nuclear magnetic resonance spectroscopy

A procedure involving alkaline extraction and solution 31P nuclear magnetic resonance (NMR) spectroscopy was developed and optimized for the characterization of P in animal manures (broiler, swine, beef cattle). Inclusion of ethylenediaminetetraacetic acid (EDTA) in the alkaline extraction solution recovered between 82 and 97% of the total P from the three manures, which represented a significant improvement on recovery in NaOH alone. Low concentrations of paramagnetic ions in all manure extracts meant that relatively long delay times (> 5 s) were required for quantitative analysis by solution 31P NMR spectroscopy. The manures contained inorganic orthophosphate, orthophosphate monoesters, orthophosphate diesters, and inorganic polyphosphates, but results were markedly influenced by the concentration of NaOH in the extractant, which affected both spectral resolution and the apparent P composition of the extracts. For example, extraction of swine manure and broiler litter with 0.5 M NaOH + 50 mM EDTA produced remarkable spectral resolution that allowed accurate quantification of the four signals from phytic acid, the major organic P compound in these manures. In contrast, more dilute NaOH concentrations produced considerable line broadening that obscured individual signals in the orthophosphate monoester region of the spectra. Spectral resolution of cattle manure extracts was relatively unaffected by NaOH concentration. Improvements in spectral resolution of more concentrated NaOH extracts were, however, compromised by the disappearance of phospholipids and inorganic polyphosphates, notably in swine and cattle manure extracts, which indicated either degradation or a change in solubility. The optimum extraction conditions will therefore vary depending on the manure type and the objectives of the study. Phytic acid can be accurately quantified in swine manure and broiler litter by extraction with 0.5 M NaOH + 50 mM EDTA, while a more dilute NaOH concentration should be used for complete P characterization or comparison among different manure types.     

Changes in negative air ions concentration under different light intensities and development of a model to relate light intensity to directional change

The purpose of this research was to determine changes in negative air ion (NAI) concentrations produced by plants grown under different light intensities. NAI concentrations were observed and analyzed in an outdoor green space with five plant species (Aloe arborescens, Clivia miniata, Chlorophytum comosum, Opuntia brunnescens, Crassula portulacea) and A. arborescens was then grown under controlled-light conditions in an enclosed space for the subsequent light intensity experiment.