Study of PCDD/Fs distribution in fly ash,ash deposits,and bottom ash from a medical waste incinerator in China

Over the past decades in China, the number of medical waste incinerators (MWIs) has been rising rapidly, causing emissions of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs). In this study, samples of fly ash, ash deposits, and bottom ash from typical MWIs were analyzed for PCDD/Fs and their distribution characteristics. Results showed international toxic equivalent (I-TEQ) values in the range of 6.9–67 ng I-TEQ/g in fly ash and ash deposits, whereas the concentration in bottom ash was extremely low (only 1.33 pg I-TEQ/g), yet the generation of PCDD/Fs was mostly de novo synthesis in fly ash and ash deposits according to the ratio of PCDFs to PCDDs; the major distribution differences of PCDD/Fs in fly ash was manifested by the content of toxic furan 2,3,7,8-TCDF, but other toxic PCDD/Fs showed similar distribution. Other findings are that 2,3,4,7,8-PeCDF had the most contribution to TEQ concentration, and that the most abundant toxic furan congener is 1,2,3,4,6,7,8-HpCDF. Correlation analysis showed that there was no significant correlation between PCDD/Fs concentration and several other physical and chemical parameters.

Implications: This paper is of interest because it presents the emission performances of PCDD/Fs in ash from medical waste incineration in China. PCDD/F contents in fly ash and ash deposits vary between 6.9 and 67.3 ng I-TEQ/g. However, the concentration in bottom ash was extremely low (only 1.33?×?10^?3 ng I-TEQ/g). The fingerprints of PCDD/Fs in fly ash are almost similar, except for 2,3,7,8-TCDF. There is no marked correlation between PCDD/Fs and other physicochemical properties.

Supplemental Materials: Supplemental materials are available for this paper. Go to the publisher's online edition of the Journal of the Air & Waste Management Association.     

CFBC固硫灰和粉煤灰复掺作水泥混合材的研究

循环流化床燃烧技术是一种节能环保的先进燃烧煤技术,但其燃烧产物固硫灰的综合利用是个重要难题.将CFBC固硫灰和普通粉煤灰复合化处理,研究了复合混合材对水泥胶砂物理性能和水泥净浆膨胀性能的影响.实验结果表明:固硫灰和粉煤灰复掺存在超叠加效应,在合适的互掺比例和细度下复合混合材具有比单掺更好的水泥胶砂强度;掺加30%复合混...     

A comparison between sludge ash and fly ash on the improvement in soft soil

In this study, the strength of soft cohesive subgrade soil was improved by applying sewage sludge ash as a soil stabilizer. Test results obtained were compared with earlier tests conducted on soil samples treated with fly ash. Five different proportions of sludge ash and fly ash were mixed with soft cohesive soil, and tests such as pH value, compaction, California bearing ratio, unconfined compressive strength (UCS), and triaxial compression were performed to understand soil strength improvement because of the addition of both ashes. Results indicate that pH values increase with extending curing age for soil with sludge ash added. The UCS of sludge ash/soil were 1.4-2 times better than untreated soil. However, compressive strength of sludge ash/soil was 20-30 kPa less than fly ash/soil. The bearing capacities for both fly ash/soil and sludge ash/soil were five to six times and four times, respectively, higher than the original capacity. Moreover, the cohesive parameter of shear strength rose with increased amounts of either ash added. Friction angle, however, decreased with increased amounts of either ash. Consequently, results show that sewage sludge ash can potentially replace fly ash in the improvement of the soft cohesive soil.     

Effects of the basicity on the comelting conditions of municipal solid waste incinerator fly ash and sewage sludge ash

In this study, the effects of the basicity on the pouring point of the municipal solid waste incinerator fly ash-sewage sludge ash mixture is investigated. Four kinds of sewage sludge ash, which were collected from several primary and secondary sewage treatment plants and were produced by different processes and sludge conditioning alternatives, were used as modifiers. The results indicate that the pouring point of the mixture increased with increasing basicity, within the range of 0.65-1.90. The pouring point is affected by the contents of the mixtures (CaO, SiO2, Al2O3, and the flux). It is suggested that an increase in the CaO content tends to raise the pouring point, whereas an increase in the SiO2 and/or the Al2O3 contents cause as adverse reaction. The prediction equation, obtained by multilinear regression (significant level is 0.05), is as follows: pouring temperature = 1189.6 + 4.19 CaO - 0.96 SiO2 - 4.33 Al2O3 (R2 = 0.91). In general, the pouring point decreased when the basicity was < 1. The pouring point apparently increased when the basicity was > 1.2. The regression squares for the different basicities were between 0.84 and 0.91. From these relationships, we note that a basicity index of 5 gave the best R2 (0.91). From the results of this study, it can be concluded that the modification of the basicity of the fly ash by the addition of sewage sludge ash to lower the pouring point is feasible and leads to a more energy-efficient melting process. In addition, these synthetic slags have a good pozzolanic reactive activity.     

对火电厂粉煤灰平衡湿含量的试验和分析

对粉煤灰的平衡湿含量在各影响因素下进行了试验研究 ,并且利用半经验公式对实验数据进行了回归 ,得到了较好的拟合效果 ;为相关的理论及试验研究提供了计算公式及实验数据     

垃圾焚烧厂焚烧底灰的处理研究

系统地研究了常州市环境卫生综合厂垃圾焚烧车间的底灰。研究结果表明，根据中国现行的污染控制标准，该厂的底灰属于一般废物，可以以建筑垃圾的方式处理。但对底灰的分选和分类研究结果表明，底灰含有一定量的未燃烬的有机废物，也有一些可回收利用的废物。因此，底灰应该先分选后，再对无利用价值的渣土作填埋或其他处置。     

Pozzolanic reactivity of the synthetic slag from municipal solid waste incinerator cyclone ash and scrubber ash

This study investigates the pozzolanic reactions and compressive strength of the blended cement manufactured using synthetic slag obtained from municipal solid waste incinerator (MSWI) cyclone ash and scrubber ash as partial replacement of portland cement. The synthetic slag was made by co-melting the MSWI scrubber ash and cyclone ash mixtures at 1400 degrees C for 30 min. Following pulverization, the different types of slag were blended with cement as cement replacement at ratios ranging from 10 to 40 wt %. The synthetic slag thus obtained was quantified, and the characteristics of the slag-blended cement pastes were examined. These characteristics included the pozzolanic activity, compressive strength, hydration activity, crystal phases, species, and microstructure at various ages. The 90-day compressive strength developed by slag-blended cement pastes with 10 and 20 wt % of the cement replaced by the synthetic slag outperformed ordinary portland cement by 1-7 MPa. X-ray diffraction species analyses indicated that the hydrates in the slag-blended cement pastes were mainly portlandite, the calcium silicate hydrate gels, and calcium aluminate hydrate salts, similar to those found in ordinary portland cement paste. Differential thermal and thermogravimetric analysis also indicated that the slag reacted with portlandite to form calcium silicate hydrate gels.     

火电灰渣场自然恢复下灰渣养分及重金属含量研究

对自然恢复下4类不同年代样地的灰渣养分含量及重金属含量进行研究,通过对比分析发现,有机质、全氮、全钾、全磷含量随着自然恢复时间的增加呈现递增的趋势,全磷含量在各恢复阶段与对照样地之间并不存在显著差异(P0.05)。pH随着恢复时间的增加呈现递减的趋势。对灰渣综合质量指数进行研究发现,自然恢复长期、中期、短期与自然恢复初期对比均有显著提高(P0.05),且随着自然恢复时间的增加灰渣综合质量指数逐渐提高。对灰渣场锌、铅、铜3种重金属研究后发现,在自然恢复下随着时间的增加,灰渣中重金属含量均呈现递减的趋势。     

Comparison of 2,4,6-trichlorophenol conversion to PCDD/ PCDF on a MSWI-fly ash and a model fly ash

We performed experiments on two different matrices with 2,4,6-trichlorophenol as precursor to Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD)/F. A municipal solid waste incinerators (MSWI) and a model fly ash were spiked in two different ways. The experiments demonstrated a three times higher formation potential of the trichlorophenol to PCDD on MSWI fly ash compared with the model fly ash used. For both fly ashes the PCDD yield was higher when gaseous trichlorophenol was fed continuously compared to mixing the fly ashes prior to the experiments with the total amount of the precursor. Despite dilution of the fly ashes tenfold with an inactive matrix the conversion of the chlorophenol was very high.     

流化床飞灰固化焚烧飞灰效果及微观分析

以深圳某垃圾焚烧厂焚烧飞灰为例分析了焚烧飞灰的性质和重金属毒性.结果表明,飞灰中 Pb 和 Cr 超出TCLP 阈值,必须进行稳定化处理.以流化床飞灰为主要成分配制固化材料,按不同比例掺人焚烧l￡灰进行固化实验,结果表明,实验范围内重金属固定效果良好.微观测试显示,固化过程主要产物有水化硅酸钙凝胶、钙矾石等,通过物理包胶、物理吸附、复分解沉淀反应和同晶替代等作用抑制重金属浸出.     

粉煤灰资源化的一种有效途径

本文对影响粉煤灰泡沫玻璃质量的主要因素:玻璃软化温度与发泡剂的选择、发泡温度与发泡时间、发泡剂生成气体的温度、坯体成型压力等关键问题进行了探索,这些问题的探索对提高粉煤灰泡沫玻璃质量,获得性能优良的粉煤灰泡沫玻璃具有十分重要的意义。     

Filtration of fly ash using a fluidized-bed filter

This study focuses on the control of particulates with a fluidized-bed filter in exhaust gas stream. The fluidized-bed filter classified in the granular bed filtration technology was employed to demonstrate the performance for removal of fly ash at indicated operating velocities, fixed bed heights, and bed temperatures; then the collecting mechanisms of particulates by fluidized-bed filter were studied. The size distribution of fly ash passing through the fluidized-bed filter was also analyzed. The results indicate that at higher operating velocities and fixed bed heights, the removal of fly ash is more efficient and inertial impaction is the main mechanism when the fluidized-bed is operated at room temperature (25 degrees C). While operating at higher temperatures (200 degrees C), efficiency of 93.2% to 99.4% can be achieved for submicron particles. It is supposed to be the diffusion mechanism that is responsible for collecting such small particles, and high temperature is a favorable condition because of diffusion.     

Glazed tiles manufactured from incinerated sewage sludge ash and clay

Sewage sludge incineration is applied extensively in highly populated cities as a final sludge treatment. In this study, incinerated ash was utilized as an additive to clay to manufacture glaze tiles. Four different amounts of ash (0, 15, 30, and 45%) were added, and five glaze concentrations (0.03, 0.06, 0.1, 0.15, and 0.2 g/cm2) were applied on the surface of biscuit tiles to study the effects of ash additive and glaze concentration on properties of fired samples. Sewage sludge was dehydrated and incinerated into ash at 800 degrees C. Subsequently, tile specimens were manufactured and fired at 800 degrees C to make biscuit tiles. Fritted glazes and iron oxide were used as the fundamental glaze and colorant, respectively. Finally, glaze was applied on the surface of biscuit tiles and then fired at 1050 degrees C to sinter them into glazed tile specimens. Tests were performed to analyze properties, including water absorption, firing shrinkage, weight loss on ignition, abrasion resistance, bending resistance, acid-alkali resistance, and aging resistance on specimens of glaze tile. To further understand more about the microstructural behavior of glazed tile specimens, analysis of energy dispersive spectrometer, scanning electron microscopy, and X-ray were carried out in this study.     

Geotechnical engineering properties of incinerator ash mixes

The incineration of solid waste produces large quantities of bottom and fly ash. Landfilling has been the primary mode of disposal of these waste materials. Shortage in landfill space and the high cost of treatment have, however, prompted the search for alternative uses of these waste materials. This study presents an experimental program that was conducted to determine the engineering properties of incinerator ash mixes for use as construction materials. Incinerator ash mixes were tested as received and around optimum compacted conditions. Compaction curves, shear strength, and permeability values of fly ash, bottom ash, and their various blends were investigated. Bottom ash tends to achieve maximum dry density at much lower water content than does fly ash. The mixes displayed a change in their cohesion and friction angle values when one of the two mix components was altered or as a result of the addition of water. The permeability of bottom ash is quite comparable to that of sand. The permeability of fly ash lies in the range of those values obtained for silts and clays. A 100% bottom ash compacted at the optimum water content has a lower density value and yields a higher friction angle and cohesion values than most construction fills. This would encourage the use of bottom ash as a fill or embankment material because free drainage of water will prevent the buildup of pore water pressures.     

粉煤灰和电石渣对聚丙烯塑料裂解的影响研究

研究了粉煤灰和电石渣对聚丙烯塑料裂解的影响,讨论了加入量对裂解速度和裂解产物的影响.结果表明:粉煤灰和电石渣都使裂解产物中的轻质部分(汽油和裂解气)增加、重油降低;粉煤灰比电石渣更能加快反应的进行,而且加入量越多,反应越快,需时越短;粉煤灰比电石渣对聚丙烯塑料的裂解具有明显的催化促进效果.     

Fluidized-bed-combustion ash for the solidification and stabilization of a metal-hydroxide sludge

Fluidized-bed-combustion (FBC) ash is a by-product from a developing technology for coal-fired power plants that will economically reduce air emissions to meet requirements of the Clean Air Act. FBC ash has physical and chemical properties similar to Portland cement, but only has moderate success as a pozzolan in concrete applications due to low compressive strengths. However, FBC ash has proven effective for use as a binder for the solidification and stabilization (S/S) of metal-bearing sludges. Physical and chemical characterization procedures were used to analyze FBC ash and a metal-bearing sludge obtained from a hazardous waste treatment facility to develop 12 different S/S mix designs. The mix designs consist of four binder designs to evaluate sludge-to-binder ratios of approximately 0, 0.5, and 1. Portland cement is used as a control binder to compare unconfined compressive strengths and Toxicity Characteristic Leaching Procedure (TCLP) analyses from different ratios of the FBC ash streams: fly ash, char, and spent bed material (SBM). Compressive strengths ranging from 84 lbs per square inch (psi) to 298 psi were obtained from various mix designs containing different sludge-to-ash ratios cured for 28 days. All the mix designs passed the TCLP. Recoveries from leaching for each metal were less than 5% for most mix designs. Results of unconfined compressive strengths, TCLP, and percent recovery calculations indicate that the mix design containing approximately a 1:1 ratio of fly ash to char-and-sludge is the best mix design for the S/S of the metal-bearing sludge.     

Dehalogenation potential of municipal waste incineration fly ash

BACKGROUND, AIMS AND SCOPE: It is well known that the fly ash from filters of municipal waste incinerators (MWI-FA) shows dehalogenation properties after heating it to 240-450 degrees C. However, this property is not general, and fly ash samples do not possess dehalogenation ability at all in many cases. Fly ash has a very variable composition, and the state of the fly ash matter therefore plays the decisive role. In the present paper, the function of important components responsible for the dehalogenation activity of MWI-FA is analysed and compared with the model fly ash. METHODS: With the aim of accounting for the dehalogenation activity of MWI-FA, the following studies of hexachlorobenzene (HCB) dechlorination were performed: The role of copper in dehalogenation experiments was evaluated for five types of metallic copper. The gasification of carbon in MWI-FA was studied in the 250-350 degrees C temperature range. Five different kinds of carbon were used, combined with conventional Cu(o) and activated nanosize copper powder. The dechlorination experiments were also carried out with Cu(II) compounds such as CuO, Cu(OH)2, CuCl2 and CuSO4. The results were discussed from the standpoint of thermodynamics of potential reactions. Based on these results, the model of fly ash was proposed, containing silica gel, metallic copper and carbon. The dechlorination ability of MWI-FA and the model fly ash are compared under oxygen-deficient atmosphere. CONCLUSIONS: The results show that, under given experimental conditions, copper acts in the dechlorination as a stoichiometric agent rather than as a catalyst. The increased surface activity of copper enhances its dechlorination activity. It was found further that the presence of copper leads to a decrease in the temperature of carbon gasification. The cyclic valence change from Cu(o) to Cu+ or Cu2+ is a prerequisite for the dehalogenation to take place. RECOMMENDATION AND OUTLOOK: Thermodynamic analysis of the dechlorination effect, as well as the comparison of dechlorination pathways on MWI-FA and model fly ash, can provide a deeper understanding of the studied reaction.     

Time-resolved leaching of cadmium and manganese from lignite and incinerator fly ash

Fly ashes from a lignite fired power plant and a municipal incinerator were leached for 3 hours using 0.1N HC1. Leachate was analyzed for Cd and Mn and plots of concentration versus time for these elements show Cd, a surface adsorbed element in the combustion process, to be rapidly removed from the ash particles in the initial four or five minutes of leaching. Manganese, a fly ash matrix element, is leached at a more constant rate as the ash praticles are dissolved. Total Cd and Mn concentrations in the incinerator fly ash are greater than total concentrations of these elements in the lignite fly ash.     

Combined glassification of EAF dust and incinerator fly ash

Stainless steelmaking dust contains large amount of heavy metals, such as Cr and Ni. If these hazardous materials are not treated properly, they will cause detrimental secondary contamination. Preliminary study on recycling stainless steelmaking dust employed the thermal molten technology. Glass-ceramics were formed by combination stainless steel dust and incinerator fly ash with the ratio of 1:9. The major phases were Augite, Akermanite, and Donathite. It was found that the glass-ceramics shows the best characteristic at 900 degrees C after 5 h of heat treatment. This product can be used as building materials or refractory materials.     

Biogenic cements from rice hull ash doped with aluminum and iron

This work describes the use of rice hull as starting material for the synthesis of cements doped with iron and aluminum. Rice hull contains about 10-20% of silica along with organic material. In many countries rice hull represents an environmental problem since this material is merely burned at rice fields, rendering suspended silica particles in the air. Dicalcium silicate (beta-Ca(2)SiO(4)) is the second most important component of Portland cement and presents many environmental advantages over commercial cement. It can be prepared at lower temperatures saving energy and raw-materials. In this work we describe the synthesis beta-Ca(2)SiO(4) using silica derived from rice hull ash. Silica was obtained from heating rice hull at 600 degrees C. Starting materials (silica, calcium oxide, barium chloride, iron or aluminum oxide) were weighed in stoichiometric proportions and aqueous dispersions having water:solid ratio of approximately 20:1 were prepared and treated in an ultrasonic bath for 60min. After this, an intermediate silicate and the excess of calcium hydroxide were obtained. Finally solids were dried, grounded and heated up to 800 degrees C. It was observed that beta-Ca(2)SiO(4) was obtained when dopant concentration was limited to 1%.