ESTIMATING ATRAZINE LEACHING IN THE MIDWEST1

Data from seven Management Systems Evaluation Areas (MSEA) were used to test the sensitivity of a leaching model, Pesticide Root Zone Model-2, to a variety of hydrologic settings in the Midwest. Atrazine leaching was simulated because it was prevalent in the MSEA studies and is frequently detected in the region's groundwater. Short-term simulations used site specific soil and chemical parameters. Generalized simulations used data avail. able from regional soil databases and standardized variables. Accurate short-term simulations were precluded by lack of antecedent atrazine concentrations in the soil profile and water, suggesting that simulations using data for less than five years underestimate atrazine leaching. The seven sites were ranked in order of atrazine detection frequency (concentration > 0.2 μg L^-1) in soil water at 2 m depth in simulations. The rank order of the sites based on long-term simulations were similar to the ranks of sites based on atrazine detection frequency from groundwater monitoring. Simulations with Map Unit Use File (MUUF) soils data were more highly correlated with ranks of observed atrazine detection frequencies than were short-term simulations using site-specific soil data. Simulations using the MIJUIF data for soil parameters were sufficiently similarity to observed atrazine detection to allow the credible use of regional soils data for simulating leaching with PRZM-2 in a variety of Midwest soil and hydrologic conditions. This is encouraging for regional modeling efforts because soil parameters are among the most critical for operating PRZM-2 and many other leaching models.     

Cadmium content of wheat grain from a long-term field experiment with sewage sludge

Grain Cd concentrations were determined in the wheat (Triticum aestivum L.) cultivars Soissons, Brigadier, and Hereward grown in 1994,1996, and 1999, respectively, in soils of a long-term field experiment to which sewage sludges contaminated with Zn, Cu, Ni, or Cr had previously been added. Soil pore water soluble Cd and free Cd2+ increased linearly with increasing total soil Cd (R2=0.82 and 0.84, respectively; P<0.001). Similarly, soil pore water free Cd2+ increased linearly with increasing soil pore water soluble Cd (R2=0.98; P<0.001). There was no evidence of a plateau in soil pore water Cd concentrations with increasing soil Cd concentrations. Grain Cd concentrations were significantly correlated with total soil Cd (P<0.001), soil pore water Cd (P<0.001), and free Cd2+ (P<0.001). A slight curvilinear relationship between grain Cd and soil Cd was apparent, but there was no plateau, even at the maximum soil Cd concentration of about 2.7 mg kg(-1). The relationship between soil pore water Cd and grain Cd was linear for all three cultivars. The slopes were in the order 1994 > 1996 > 1999, with more Cd being taken up into the grain by Soissons grown in 1994, and least by Hereward grown in 1999. For Soissons, Cd concentration in the grain greater than the EU limit (0.24 mg kg(-1) dry wt.) occurred at soil Cd less than the current UK limit of 3 mg kg(-1) for soils receiving sewage sludge. In contrast, for Brigadier and Hereward, grain Cd concentrations were near to and less than the EU limit, respectively, at soil Cd concentrations of 3 mg kg(-1).     

Mapping the probability of exceeding critical thresholds for cadmium concentrations in soils in The Netherlands

The probability of exceeding critical thresholds of Cd concentrations in the soil was mapped at a national scale. The critical thresholds in soil were based on food quality criteria for Cd in crops or in organs of cattle (Bos taurus), and were calculated by inverting a regression model for the Cd concentration in the crop, with the Cd concentration in soil, soil organic matter (SOM) content, clay content, and pH as predictors. The probability of exceeding the critical threshold for Cd in soil per node of a 500- x 500-m grid was approximated by Monte Carlo simulation, using the estimated cumulative distribution functions (cdf) of SOM, clay, pH, and Cd as input. The cdfs were estimated by simple indicator kriging with local prior means. For SOM, clay, and pH, detailed maps of soil type and land use were used to define subregions with assumed constant local means of the indicators (a priori distributions). The cdfs were sampled by Latin hypercube sampling. We accounted for correlation between the actual and critical Cd concentrations in soil by drawing Cd values from cdfs conditional on SOM and clay. The estimated probability for grassland is negligible, even in areas with high Cd concentrations in soil, and for maize (Zea mays L.) land the probability is almost everywhere smaller than 5%. For arable soils, however, these probabilities commonly are larger than 5% when sugar beet (Beta vulgaris L.) or wheat (Triticum aestivum L.) is taken as a reference crop, and locally exceed 50%.     

Potential risks of copper, zinc, and cadmium pollution due to pig manure application in a soil-rice system under intensive farming: a case study of Nanhu, China

Heavy metal (copper [Cu], zinc [Zn], and cadmium [Cd]) pollution of soils from pig manures in soil-rice ( L.) systems under intensive farming was investigated, taking Nanhu, China, as the case study area. Two hundred pig manures and 154 rice straws, brown rice samples, and corresponding surface soil (0-15 cm) samples were collected in paddy fields from 150 farms in 16 major villages within the study area. The mean Cu and Zn concentrations in pig manures consistently exceeded the related standard. About 44 and 60% of soil samples exceed the Chinese Soil Cu and Cd Environmental Quality Standards, respectively. The concentration of Cu, Zn, and Cd in brown rice did not exceed the Chinese Food Hygiene Standard. There was a significant positive correlation between total Cu and Zn contents in soil and application rate of pig manures. Strong correlation was observed between the extractable Cu, Zn, and Cd in soil and the Cu, Zn, and Cd contents in the brown rice. The spatial distribution maps of Cu and Zn concentrations in brown rice, straw, and extractable soil Cu and Zn concentration also showed similar geographical trends. Further analyses on heavy metals loading flux and accumulation rates from pig manure applied suggested that Cu and Cd contents in soil currently have already exceeded the maximum permissible limit, and Zn, if still at current manure application rates, will reach the ceiling concentration limits in 9 yr. This study assists in understanding the risk of heavy metals accumulating from pig manure applications to agricultural soils.     

Effect of Cadmium on Microbial Activity and a Ryegrass Crop in Two Semiarid Soils

Soil pollution with Cd is an environmental problem common in the world, and it is necessary to establish what Cd concentrations in soil could be dangerous to its fertility from toxicity effects and the risk of transference of this element to plants and other organisms of the food chain. In this study, we assessed Cd toxicity on soil microorganisms and plants in two semiarid soils (uncultivated and cultivated). Soil ATP content, dehydrogenase activity, and plant growth were measured in the two soils spiked with concentrations ranging from 3 to 8000 mg Cd/kg soil and incubated for 3 h, 20 days, and 60 days. The Cd concentrations that produced 5%; 10%;, and 50%; inhibition of each of the two soil microbiological parameter studied (ecological dose, ED, values) were calculated using two different mathematical models. Also, the effect of Cd concentration on plant growth of ryegrass (Lolium perenne, L.) was studied in the two soils. The Cd ED values calculated for soil dehydrogenase activity and ATP content were higher in the agricultural soils than in the bare soil. For ATP inhibition, higher ED values were calculated than for dehydrogenase activity inhibition. The average yields of ryegrass were reduced from 5.03 to 3.56 g in abandoned soil and from 4.21 to 1.15 g in agricultural soil with increasing concentrations of Cd in the soil. Plant growth was totally inhibited in abandoned and agricultural soils at Cd concentrations above 2000 and 5000 mg/kg soil, respectively. There was a positive correlation between the concentration of Cd in the plants and the total or DTPA-extractable concentrations of Cd in the soil.     

Site-specific phosphorus application based on the kriging fertilizer-phosphorus availability index of soils

Site-specific phosphorus management is done to optimize crop production and minimize P loss from soils. The spatial variability of the available P prior to fertilizer application and the P-fixation tendency of soil both need to be taken into account for variable-rate P application. The objectives of this research were to document the spatial variability of the fertilizer-P availability index, which shows the P-fixation tendency, and to develop a strategy that takes the spatial distribution of this index into account for site-specific phosphorus application. In this study, the spatial patterns of the fertilizer-P availability index were characterized by using geostatistics. The ordinary kriging was used for spatial interpolation of the fertilizer-P availability index. Because the fertilizer-P availability index of soil is related to oxalate-extractable Fe and Al and because measuring oxalate-extractable Fe and Al is much easier than directly determining the fertilizer-P availability index, the spatial distribution of the fertilizer-P availability index can be obtained using the oxalate-extractable Fe and Al data. The spatial distribution of Olsen-extractable P, which was used to measure the available-P status prior to fertilizer-P application, was also estimated by using ordinary kriging. The required fertilizer-P amounts were then determined using the kriging estimates of the fertilizer-P availability index and Olsen-extractable P. A fertilizer-P recommendation map for the 430-ha study site in Changhua county, Taiwan was generated by using this approach for illustration. The proposed method for generating fertilizer-P recommendation maps can be used for variable-rate application to maintain an adequate P status for crop production and to potentially reduce the P loss from soils.     

Uncertainty Assessment for Management of Soil Contaminants with Sparse Data

In order for soil resources to be sustainably managed, it is necessary to have reliable, valid data on the spatial distribution of their environmental impact. However, in practice, one often has to cope with spatial interpolation achieved from few data that show a skewed distribution and uncertain information about soil contamination. We present a case study with 76 soil samples taken from a site of 15 square km in order to assess the usability of information gleaned from sparse data. The soil was contaminated with cadmium predominantly as a result of airborne emissions from a metal smelter. The spatial interpolation applies lognormal anisotropic kriging and conditional simulation for log-transformed data. The uncertainty of cadmium concentration acquired through data sampling, sample preparation, analytical measurement, and interpolation is factor 2 within 68.3 % confidence. Uncertainty predominantly results from the spatial interpolation necessitated by low sampling density and spatial heterogeneity. The interpolation data are shown in maps presenting likelihoods of exceeding threshold values as a result of a lognormal probability distribution. Although the results are not deterministic, this procedure yields a quantified and transparent estimation of the contamination, which can be used to delineate areas for soil improvement, remediation, or restricted area use, based on the decision-makers probability safety requirement.     

Predicting cadmium concentrations in wheat and barley grain using soil properties

The entry of Cd into the food chain is of concern as it can cause chronic health problems. To investigate the relationship between soil properties and the concentration of Cd in wheat (Triticum aestivum L.) and harley (Hordeum vulgare L.) grain, we analyzed 162 wheat and 215 barley grain samples collected from paired soil and crop surveys in Britain, and wheat and barley samples from two long-term sewage sludge experiments. Cadmium concentrations were much lower in barley grain than in wheat grain under comparable soil conditions. Multiple regression analysis showed that soil total Cd and pH were the significant factors influencing grain Cd concentrations. Significant cultivar differences in Cd uptake were observed for both wheat and barley. Wheat grain Cd concentrations could be predicted reasonably well from soil total Cd and pH using the following model: log(grain Cd) = a + b log(soil Cd) - c(soil pH), with 53% of the variance being accounted for. The coefficients obtained from the data sets of the paired soil and crop surveys and from long-term sewage sludge experiments were similar, suggesting similar controlling factors of Cd bioavailability in sludge-amended or unamended soils. For barley, the model was less satisfactory for predicting grain Cd concentration (22% of variance accounted for). The model can be used to predict the likelihood of wheat grain Cd exceeding the new European Union (EU) foodstuff regulations on the maximum permissible concentration of Cd under different soil conditions, particularly in relation to the existing Directive and the proposed new Directive on land applications of sewage sludge.     

Heavy metal release from contaminated soils: comparison of column leaching and batch extraction results

Heavy metals in soils may adversely affect environmental quality. In this study, we investigated the release of Zn, Cd, Pb, and Cu from four contaminated soils by column leaching and single and sequential batch extractions. Homogeneously packed soil columns were leached with 67 mL/g 10(-2) M CaCl2 to investigate the exchangeable metal pool and subsequently with 1400 mL/g 10(-2) M CaCl2 adjusted to pH 3 to study the potential of metal release in response to soil acidification. In two noncalcareous soils (pH 5.7 and 5.1), exchange by Ca resulted in pronounced release peaks for Zn and Cd that were coupled to the exchange of Mg by Ca, and 40 to 70% of total Zn and Cd contents were rapidly mobilized. These amounts compared well with exchangeable pools determined in single and sequential batch extractions. In two soils with near-neutral pH, the effluent concentrations of Zn and Cd were several orders of magnitude lower and no pronounced elution peaks were observed. This behavior was also observed for Cu and Pb in all four soils. When the soils were leached at pH 3, the column effluent patterns reflected the coupling of CaCO3 dissolution (if present) and other proton buffering reactions, proton-induced metal release, and metal-specific readsorption within the soil column. Varying the flow rate by a factor of five had only minor effects on the release patterns. Overall, Ca exchange and subsequent acidification to pH 3 removed between 65 and 90% of total Zn, Cd, Pb, and Cu from the four contaminated soils.     

Assessment of contamination from arsenical pesticide use on orchards in the Great Valley region, Virginia and West Virginia, USA

Lead arsenate pesticides were widely used in apple orchards from 1925 to 1955. Soils from historic orchards in four counties in Virginia and West Virginia contained elevated concentrations of As and Pb, consistent with an arsenical pesticide source. Arsenic concentrations in approximately 50% of the orchard site soils and approximately 1% of reference site soils exceed the USEPA Preliminary Remediation Goal (PRG) screening guideline of 22 mg kg(-1) for As in residential soil, defined on the basis of combined chronic exposure risk. Approximately 5% of orchard site soils exceed the USEPA PRG for Pb of 400 mg kg(-1) in residential soil; no reference site soils sampled exceed this value. A variety of statistical methods were used to characterize the occurrence, distribution, and dispersion of arsenical pesticide residues in soils, stream sediments, and ground waters relative to landscape features and likely background conditions. Concentrations of Zn, Pb, and Cu were most strongly associated with high developed land density and population density, whereas elevated concentrations of As were weakly correlated with high orchard density, consistent with a pesticide residue source. Arsenic concentrations in ground water wells in the region are generally <0.005 mg L(-1). There was no spatial association between As concentrations in ground water and proximity to orchards. Arsenic had limited mobility into ground water from surface soils contaminated with arsenical pesticide residues at concentrations typically found in orchards.     

Genotoxicity is unrelated to total concentration of priority carcinogenic polycyclic aromatic hydrocarbons in soils undergoing biological treatment

A solid-phase microbiological assay was used to determine the changes in genotoxicity associated with sequestration or biodegradation of carcinogenic compounds in contaminated soils. The concentration of six carcinogenic polycyclic aromatic hydrocarbons (PAHs) did not change in 59 d in sterile soil, but the genotoxicity declined markedly. In a soil undergoing bioremediation in the field for 147 d or biodegradation in the laboratory for 180 d, the concentrations either changed little or declined at different rates, but the genotoxicity increased followed by a decline. The genotoxicity of a second soil declined as a result of biological treatment. The data show that genotoxicity of contaminated soils may be unrelated to the concentration of carcinogenic PAHs because of aging or new mutagens formed during biological treatment.     

Spatial distributions and potential risk analysis of total soil selenium in Guangdong Province, China

A total of 260 soil profiles were examined to investigate the spatial distribution of total soil selenium (Se) in Guangdong province, China. In the investigated area, the soil Se concentrations follow an approximately lognormal distribution. The soil Se geometric mean concentration of 0.23 mg kg(-1) is higher than that of Chinese soils; however, Se concentration varies over the study area. The baseline concentration of 0.13 to 0.41 mg kg(-1) indicates that the soil Se concentration is mostly in the range of deficiency to medium level for surface soils in Guangdong province. In A-, B-, and C-horizon, soil Se spatial distribution is correlated with the nature of the parent material, with high Se concentration mainly located in limestone and sandshale areas and low Se concentration associated with purple shale and granite areas. The spatial distribution pattern of soil Se concentrations suggests that potential Se deficiency may be an issue for human health in this province. Moreover, due to soil degradation and erosion, calculated soil Se exported into surrounding waters could reach approximately 23,000 kg yr(-1) in the study area.     

Prediction of zinc, cadmium, lead, and copper availability to wheat in contaminated soils using chemical speciation, diffusive gradients in thin films, extraction, and isotopic dilution techniques

To predict the availability of metals to plants, it is important to understand both solution- and solid-phase processes in the soil, including the kinetics of metal release from its binding agent (ligand and/or particle). The present study examined the speciation and availability of Zn, Cd, Pb, and Cu in a range of well-equilibrated metal-contaminated soils from diverse sources using several techniques as a basis for predicting metal uptake by plants. Wheat (Triticum aestivum L.) was grown in 13 metal-contaminated soils and metal tissue concentrations (Zn, Cd, Pb, and Cu) in plant shoots were compared with total soil metal concentrations, total soluble metal, and free metal activities (pM2+) in soil pore waters, 0.01 M CaCl2-extractable metal concentrations, E values measured by isotope dilution, and effective metal concentrations, C(E), measured by diffusive gradients in thin films (DGT). In the DGT technique, ions are dynamically removed by their diffusion through a gel to a binding resin, while E values represent the isotopically exchangeable (labile) metal pools. Free metal activities (Zn2+, Cd2+, and Pb2+) in soil pore waters were determined using a Donnan dialysis technique. Plant Zn and Cd concentrations were highly related to C(E), while relationships for Zn and Cd with respect to the other measures of metals in the soils were generally lower, except for CaCl2-extractable Cd. These results suggest that the kinetically labile solid-phase pool of metal, which is included in the DGT measurement, played an important role in Zn and Cd uptake by wheat along with the labile metal in soil solution. Plant Pb concentrations were highly related to both soil pore water concentrations and C(E), indicating that supply from the solid phase may not be so important for Pb. Predictions of Cu uptake by wheat from these soils by the various measures of Cu were generally poor, except surprisingly for total Cu.     

Modeling the environmental fate of cadmium in a large wastewater irrigation area

The fate of cadmium in soils is governed by spatially heterogeneous processes that proceed from decades to centuries. This study aimed at modeling the fate of Cd within the wastewater irrigation area (WIA) of Braunschweig (Germany). The sandy soils (mainly Dystric Cambisol or Typic Haplumbrept) at this site (28 km2) have received considerable loads of heavy metals by irrigation of municipal wastewater for up to 40 yr. The soils of the WIA are in agricultural use. The main crops are sugar beet (Beta vulgaris L.), potato (Solanum tuberosum L.), and wheat (Triticum aestivum L.). As a result of asparagus (Asparagus officinalis L.) cropping, about 15% of the soils have been converted to Rigosols. In 1996, we measured the vertical distribution (0 to 1.2 m) of soil pH, organic carbon content, and the EDTA-extractable content and the solution phase concentration of Cd at 153 sites. At sites not used for asparagus cultivation, Cd has migrated on average to a depth of about 0.5 m. Due to deep plowing, which accelerates migration, Cd has been displaced on average to about 0.7 m at the Rigosol sites. To model the fate of Cd at the scale of the WIA, we used different parallel soil column approaches. In each column the local model SEFAH was used to simulate both displacement and plant uptake of Cd. The model was fed with measured or randomly generated soil data. The results of retrospective simulations from 1957 to 1996 agreed well with observed Cd profiles. The better the spatial variability of sorption was described, the better the performance. Our simulation results show that Cd pollution of soil at first affects the soil-plant pathway. The breakthrough of Cd to the groundwater is dampened and is delayed for many decades.     

A comparison of reliability of soil cadmium determination by standard spectrometric methods

Inductively coupled plasma emission spectrometry (ICP-OES) is the most common method for determination of soil Cd, yet spectral and matrix interferences affect measurements at the available analytical wavelengths for this metal. This study evaluated the severity of the interference over a range of total soil Cd by comparing ICP-OES and inductively coupled plasma mass spectrometry (ICP-MS) measurements of Cd in acid digests. Using the emission at 226.5 nm, ICP-OES was generally unable to quantify soil Cd at low (near-background) levels and gave unreliable values compared with ICP-MS. Using the line at 228.8 nm, a marked positive bias in Cd measurement (relative to the 226.5 nm measurement) was attributable to arsenic (As) interference even at soil As concentrations below 10 mg kg. This spectral interference in ICP-OES was severe in As-contaminated orchard soils, giving a false value for soil total Cd near 2 mg kg when soil As was 100 to 150 mg kg. In attempting to avoid these ICP emission-specific interferences, this study evaluated a method to estimate total soil Cd using 1 M HNO extraction followed by determination of Cd by flame atomic absorption (FAA), either with or without preconcentration of Cd using an Aliquat-heptanone extractant. The 1 M HNO extracted an average of 82% of total soil Cd. The FAA method had no significant interferences and estimated the total Cd concentrations in all soils tested with acceptable accuracy. For Cd-contaminated soils, the Aliquat-heptanone preconcentration step was not necessary, as FAA sensitivity was adequate for quantification of extractable soil Cd and reliable estimation of total soil Cd.     

Kriging method evaluation for assessing the spatial distribution of urban soil lead contamination

Describing contaminant spatial distribution is an integral component of risk assessment. Application of geostatistical techniques for this purpose has been demonstrated previously. These techniques may provide both an estimate of the concentration at a given unsampled location, as well as the probability that the concentration at that location will exceed a critical threshold concentration. This research is a comparative study between multiple indicator kriging and kriging with the cumulative distribution function of order statistics, with both local and global variograms. The aim was to determine which of the four methods is best able to delineate between "contaminated" and "clean" soil. The four methods were validated with a subset of data values that were not used in the prediction. Method performance was assessed by calculating the root mean square error (RMSE), analysis of variance, the proportion of sites misclassified by each method as either "clean" when they were actually "contaminated" or vice versa, and the expected loss for each misclassification type. The data used for the comparison were 807 topsoil Pb concentrations from the inner-Sydney suburbs of Glebe and Camperdown, Australia. While there was very little difference between the four methods, multiple indicator kriging was found to produce the most accurate predictions for delineating "clean" from "contaminated" soil.     

Impact of unconfined sulphur-mine waste on a semi-arid environment (Almería, SE Spain)

Thirty-five soil samples were taken from unconfined mine waste, stream sediments, and surfaces unoccupied by mining and presumably unaffected by it, in a sulphur-mining zone surrounded by carbonate material and characterized by a semi-arid climate with short torrential storms. These samples were analysed and the results compared to estimate the spread of pollution in the landscape and to assess potential environmental risk. The mean concentrations of S, Zn, Cd, Pb, and As in mine waste were between 3.5-fold (As) and 50-fold (S) greater than unaffected soils. Oxidation of S led to a sharp drop in pH, strong weathering of minerals, and solubilisation of the constituent elements, forming a toxic acidic mine drainage with highly concentrated pollutants that were discharged into the drainage channels. Successive acid mine drainage into the soil on the valley floor spreads acidification and pollution downstream. The high carbonate content in surrounding soils played an important role in the increase of the pH and precipitation of S, Pb, and Al of the affected soils. Meanwhile, high mobility of Zn, Cd and As under basic conditions and a low Fe concentration explain the broad spread of these elements, as high concentrations were detected in soil more than 2000 m from the source. Only the soil solutions from near the waste dump (first 500 m) were highly phytotoxic, and moderately phytotoxic from 500 to 1500 m away. The concentration of pollutants in the leachates was clearly higher than in soil solutions, even in the soils located over 2000 m from the source, implying that the size of the polluted area will increase with time.     

Soil-to-root transfer and translocation of polycyclic aromatic hydrocarbons by vegetables grown on industrial contaminated soils

Polycyclic aromatic hydrocarbons (PAHs) are possible contaminants in some former industrial sites, representing a potential risk to human health if these sites are converted to residential areas. This work was conducted to determine whether PAHs present in contaminated soils are transferred to edible parts of selected vegetables. Soils were sampled from a former gasworks and a private garden, exhibiting a range of PAH concentrations (4 to 53 to 172 to 1263 and 2526 mg PAHs kg-1 of dry soil), and pot experiments were conducted in a greenhouse with lettuce (Lactuca sativa L. var. Reine de Mai), potato (Solanum tuberosum L. var. Belle de Fontenay), and carrot (Daucus carota L. var. Nantaise). At harvest, above- and below ground biomass were determined and the PAH concentrations in soil were measured. In parallel, plates were placed in the greenhouse to estimate the average PAH-dust deposition. Results showed that the presence of PAHs in soils had no detrimental effect on plant growth. Polycyclic aromatic hydrocarbons were detected in all plants grown in contaminated soils. However, their concentration was low compared with the initial soil concentration, and the bioconcentration factors were low (i.e., ranging from 13.4 x 10(-4) in potato and carrot pulp to 2 x 10(-2) in potato and carrot leaves). Except in peeled potatoes, the PAH concentration in vegetables increased with the PAH concentration in soils. The PAH distribution profiles in plant tissues and in soils suggested that root uptake was the main pathway for high molecular weight PAHs. On the opposite, lower molecular weight PAHs were probably taken up from the atmosphere through the leaves as well as by roots.     

Natural attenuation of residual heavy metal contamination in soils affected by the Aznalcóllar mine spill, SW Spain

Non-amended soils affected by pyritic sludge residues were monitored for 7 years to assess the long-term natural attenuation ability of these soils. The decrease in both the total concentration of elements (particularly As) and (NH(4))(2)SO(4)-extractable fractions of Mn, and Zn, below the maximum permissible levels indicate a successful natural ability to attenuate soil pollution. Soil acidification by pyrite oxidation and rainfall-enhanced leaching were the largest contributors to the reduction of metals of high (Mn, Cu, Zn and Cd) and low (Fe, Al, and As) availability. Periodic use of correlation and spatial distribution analysis was useful in monitoring elemental dispersion and soil property/element relationships.     

Cadmium and zinc in vegetation and litter of a voluntary woodland that has developed on contaminated sediment-derived soil

Vegetation that develops spontaneously on metal-contaminated soils presents an opportunity to evaluate both metal bioavailability and the risks posed to biota. The behavior of Cd and Zn in the species of a spontaneously developed woodland, colonizing a canal embankment, has been investigated. Nitric-acid-extractable metal concentrations in the sediment-derived substrate ranged between 5.0 to 376 mg kg(-1)dry wt. Cd and 83.0 to 784 mg kg(-1)dry wt. Zn. The woodland is dominated by Willow (Salix) species. Salix caprea selectively accumulated Cd in all stem tissues, in contrast to S. viminalis, which regulated tissue Cd content. Both species showed an effective regulation of tissue Zn. Cadmium uptake by S. caprea was correlated with differences in soil pH, while Zn uptake was not. There was no relationship between tissue metal concentrations and soil metal nitric acid-extractable concentrations. Other aspects of ecosystem function appeared unaffected by the elevated Cd flux in S. caprea; leaf litter organisms present represented all major groups and there was no accumulation of organic matter. The woodland represents a potentially sustainable option for remediating a low value site with difficult access that does not involve removal of the contaminated material to a landfill or making a permanent inert cover.