Detection of bacterial endotoxin in drinking tap and bottled water in Kuwait

This study was carried out to measure and compare the concentration of bacterial endotoxin in a variety of samples from drinking tap and bottled water available in Kuwait by using the Limulus Amoebocyte lysate test. A total of 29 samples were tested. Samples were collected from a variety of locations throughout the six governorates of Kuwait and 23 brands of local and imported bottled water samples were collected from the local market. The concentration of bacterial endotoxin was measured by using the standard Limulus Amoebocyte lysate test, gel clot method. This study showed that measured endotoxin concentrations in tap drinking water varied from 2.4 to 33.8?EU/ml with the average endotoxin concentration of 14.2?EU/ml. While the results of endotoxin concentrations in the bottled water were <0.03 to 20.1?EU/ml with an average of 1.96?EU/ml. The average concentration of endotoxin in bottled water is 13.5 % of the average concentration of endotoxin in tap drinking water. This experimental investigation has proved that drinking bottled water has less endotoxin as compared to tap water in Kuwait. It is also demonstrated that the endotoxin concentration did not exceed the acceptable level in drinking tap water.     

Desorption of arsenic from drinking water distribution system solids

Previous work has shown that arsenic can accumulate in drinking water distribution system (DWDS) solids (Lytle et~al., 2004) when arsenic is present in the water. The release of arsenic back into the water through particulate transport and/or chemical release (e.g. desorption, dissolution) could result in elevated arsenic levels at the consumers' tap. The primary objective of this work was to examine the impact of pH and orthophosphate on the chemical release (i.e. desorption) of arsenic from nine DWDS solids collected from utilities located in the Midwest. Arsenic release comparisons were based on the examination of arsenic and other water quality parameters in leach water after contact with the solids over the course of 168~hours. Results showed that arsenic was released from solids and suggested that arsenic release was a result of desorption rather than dissolution. Arsenic release generally increased with increasing initial arsenic concentration in the solid and increasing pH levels (in the test range of 7 to 9). Finally, orthophosphate (3 and 5 mg PO₄/L) increased arsenic release at all pH values examined. Based on the study results, utilities with measurable levels of arsenic present in their water should be aware that some water quality changes can cause arsenic release in the DWDS potentially resulting in elevated levels at the consumer's tap.     

Water quality assessment of Ogun river, South West Nigeria

The quality of Ogun river in South-West, Nigeria was studied by a field survey for a period of 1 year (covering dry season and rainy season). Water samples were collected from thirteen sites and analysed for physico-chemical and bacteriological parameters as well as heavy metals using standard methods. Generally, the values obtained for turbidity, phosphate, oil and grease, iron and faecal coliform from all the sites in both seasons were above the maximum acceptable limit set by the World Health Organization (WHO) for drinking water. Also, the manganese content from all the sites in the dry season, lead concentrations from three sites in the dry season and cadmium concentrations from some sites in both seasons were above the WHO limit. The values obtained for total dissolved solids, dissolved oxygen and chloride at site M in the dry season and nitrate at site J in the rainy season were also above the WHO limit. Pollution of Ogun river water along its course is evidenced by the high concentrations of pollution indicators, nutrients and trace metals above the acceptable limit. This poses a health risk to several rural communities who rely on the river primarily as their source of domestic water. The study showed a need for continuous pollution monitoring programme of surface waters in Nigeria.     

Evaluation of hydrochemical changes due to intensive aquifer exploitation: case studies from Mexico

The impact of intensive aquifer exploitation has been observed in numerous places around the world. Mexico is a representative example of this problem. In 2010, 101 out of the 653 aquifers recognized in the country, showed negative social, economic, and environmental effects related to intensive exploitation. The environmental effects include, among others, groundwater level decline, subsidence, attenuation, and drying up of springs, decreased river flow, and deterioration of water quality. This study aimed at determining the hydrochemical changes produced by intensive aquifer exploitation and highlighting water quality modifications, taking as example the Valle de Toluca, Salamanca, and San Luis Potosi aquifers in Mexico's highlands. There, elements such as fluoride, arsenic, iron, and manganese have been detected, resulting from the introduction of older groundwater with longer residence times and distinctive chemical composition (regional flows). High concentrations of other elements such as chloride, sulfate, nitrate, and vanadium, as well as pathogens, all related to anthropogenic pollution sources (wastewater infiltration, irrigation return flow, and atmospheric pollutants, among others) were also observed. Some of these elements (nitrate, fluoride, arsenic, iron, and manganese) have shown concentrations above Mexican and World Health Organization drinking water standards.     

Arsenic content in ground and canal waters of Punjab, North-West India

Groundwater is the primary source of drinking water for more than 95% of the population in Punjab. The world health organization and US Environment Protection Agency recently established a new maximum contaminant level of 10 ppb for arsenic in drinking water. The arsenic concentration of deep water tube wells located in Amritsar city used for domestic supply for urban population ranged from 3.8 to 19.1 ppb with mean value of 9.8 ppb. Arsenic content in hand pump water varied from 9 to 85 ppb with a mean value of 29.5 ppb. According to the safe limit of As, 54% and 97%, water samples collected from deep water tube wells and hand pumps, respectively, were not fit for human consumption. Arsenic content in canal water varied from 0.3 to 8.8 ppb with a mean value of 2.89 ppb. Canal water has got higher oxidation potential followed by deep tube well and hand pump water. The present study suggests the regular monitoring of arsenic content in deep tube well and shallow hand pump waters by water testing laboratories. The consumption of water having elevated concentration of As above the safe limit must be discouraged. In south-western districts of Punjab, it recommends the use of canal water for drinking purposes and domestic use by rural and urban populations than ground water sources.     

Arsenic exposure in Hungary, Romania and Slovakia

Inorganic arsenic is a potent human carcinogen and toxicant which people are exposed to mainly via drinking water and food. The objective of the present study was to assess current exposure to arsenic via drinking water in three European countries. For this purpose, 520 individuals from four Hungarian, two Slovakian and two Romanian countries were investigated by measuring inorganic arsenic and methylated arsenic metabolites in urine by high performance liquid chromatography with hydride generation and inductively coupled plasma mass spectrometry. Arsenic in drinking water was determined by atomic absorption spectrometry. Significantly higher concentrations of arsenic were found in both the water and the urine samples from the Hungarian counties (median: 11 and 15 microg dm(-3), respectively; p < 0.001) than from the Slovakian (median: 0.94 and 4.5 microg dm(-3), respectively) and Romanian (median: 0.70 and 2.1 microg dm(-3), respectively) counties. A significant correlation was seen between arsenic in water and arsenic in urine (R(2)= 0.46). At low water arsenic concentrations, the relative amount of dimethylarsinic acid (DMA) in urine was increased, indicating exposure via food. Also, high body mass index was associated with higher concentrations of arsenic in urine (p= 0.03), mostly in the form of DMA. Smokers had significantly higher urinary arsenic concentrations than non-smokers (p= 0.03). In conclusion, elevated arsenic exposure via drinking water was prevalent in some of the counties. Exposure to arsenic from food, mainly as DMA, and cigarette smoke, mainly as inorganic arsenic, are major determinants of arsenic exposure at very low concentrations of arsenic in drinking water.     

Arsenic and Other Metal Contamination of Groundwaters in the Industrial Area of Thessaloniki, Northern Greece

In groundwater, used for drinking water supply in the greater industrial area of Thessaloniki, in Northern Greece, concentrations of total arsenic exceeded the WHO provisional guideline value and the EU maximum contaminant level (MCL) of 10 μg/L. The concentration of total arsenic was in the range between 4–130 μg/L, whereas the median value was 36 μg/L and the average concentration 46 μg/L. Nine out of the eleven wells contained total arsenic at concentration higher than 10 μg/L and it should be stressed that 6 of them contain arsenic at concentrations between 10 (new MCL) and 50 μg/L (previous MCL). The examined groundwaters were found to contain elevated concentrations of manganese and phosphate. Arsenic had a positive correlation with the pH, indicating the possible effect of pH on arsenic mobilisation. These findings emerge the problem of contamination from arsenic, since, according to the EU directive 98/83, all drinking water sources within the European Union should have achieved compliance with the new limits by 12/2003, implying that the situation requires urgent remedial action.     

Molybdenum distributions and variability in drinking water from England and Wales

An investigation has been carried out of molybdenum in drinking water from a selection of public supply sources and domestic taps across England and Wales. This was to assess concentrations in relation to the World Health Organization (WHO) health-based value for Mo in drinking water of 70 μg/l and the decision to remove the element from the list of formal guideline values. Samples of treated drinking water from 12 water supply works were monitored up to four times over an 18-month period, and 24 domestic taps were sampled from three of their supply areas. Significant (p?p?>?0.05) were detected. Tap water samples collected from three towns (North Wales, the English Midlands, and South East England) supplied uniquely by upland reservoir water, river water, and Chalk groundwater, respectively, also showed a remarkable uniformity in Mo concentrations at each location. Within each, the variability was very small between houses (old and new), between pre-flush and post-flush samples, and between the tap water and respective source water samples. The results indicate that water distribution pipework has a negligible effect on supplied tap water Mo concentrations. The findings contrast with those for Cu, Zn, Ni, Pb, and Cd, which showed significant differences (p?England and Wales.     

Determination of trace metals in drinking water in Irbid City-Northern Jordan

Drinking water samples from Irbid, the second populated city in Jordan were analyzed for trace metals (As, Ba, Cd, Pb, Cr, Cu, Fe, Zn, Mn, Ni, and Se) content. The study was undertaken to determine if the metal concentrations were within the national and international guidelines. A total of 90 drinking water samples were collected from Al-Yarmouk University area. The samples were collected from three different water types: tap water (TW), home-purified water (HPW), and plant-purified water (PPW). All the samples were analyzed for trace metals using an inductively coupled plasma-optical emission spectrometry. All the samples analyzed were within the United States Environmental Protection Agency admissible pH limit (6.5–8.5). The results showed that concentrations of the trace metals vary significantly between the three drinking water types. The results showed that HPW samples have the lowest level of trace metals and the concentrations of some essential trace metals in these samples are less than the recommended amounts. Slight differences in the metal contents were found between HPW samples, little differences between PPW samples; however, significant differences were found between TW samples. Although some TW samples showed high levels of trace metals, however, the mean level of most elements determined in the samples were well within the Jordanian standards as well as the World Health Organization standards for drinking water.     

Nitrate,sulphate and chloride contents in public drinking water supplies in Sicily,Italy

Water samples collected from public drinking water supplies in Sicily were analysed for electric conductivity and for their chloride, sulphate and nitrate contents. The samples were collected as uniformly as possible from throughout the Sicilian territory, with an average sampling density of about one sample for every 7,600 inhabitants. Chloride contents that ranged from 5.53 to 1,302 mg/l were correlated strongly with electric conductivity, a parameter used as a proxy for water salinity. The highest values are attributable to seawater contamination along the coasts of the island. High chloride and sulphate values attributable to evaporitic rock dissolution were found in the central part of Sicily. The nitrate concentrations ranged from 0.05 to 296 mg/l, with 31 samples (4.7% of the total) exceeding the maximum admissible concentration of 50 mg/l. Anomalous samples always came from areas of intensive agricultural usage, indicating a clear anthropogenic origin. The same parameters were also measured in bottled water sold in Sicily, and they all were within the ranges for public drinking water supplies. The calculated mean nitrate intake from consuming public water supplies (16.1 mg/l) did not differ significantly from that of bottled water (15.2 mg/l). Although the quality of public water supplies needs to be improved by eliminating those that do not comply with the current drinking water limits, at present it does not justify the high consumption of bottled water (at least for nitrate contents).     

Groundwater arsenic contamination in Brahmaputra river basin: a water quality assessment in Golaghat (Assam), India

Distribution of arsenic (As) and its compound and related toxicology are serious concerns nowadays. Millions of individuals worldwide are suffering from arsenic toxic effect due to drinking of As-contaminated groundwater. The Bengal delta plain, which is formed by the Ganga?CPadma?CMeghna?CBrahmaputra river basin, covering several districts of West Bengal, India, and Bangladesh is considered as the worst As-affected alluvial basin. The present study was carried out to examine As contamination in the state of Assam, an adjoining region of the West Bengal and Bangladesh borders. Two hundred twenty-two groundwater samples were collected from shallow and deep tubewells of six blocks of Golaghat district (Assam). Along with total As, examination of concentration levels of other key parameters, viz., Fe, Mn, Ca, Na, K, and Mg with pH, total hardness, and SO $_{4}^{2-}$ , was also carried out. In respect to the permissible limit formulated by the World Health Organization (WHO; As 0.01 ppm, Fe 1.0 ppm, and Mn 0.3 ppm for potable water), the present study showed that out of the 222 groundwater samples, 67%, 76.4%, and 28.5% were found contaminated with higher metal contents (for total As, Fe, and Mn, respectively). The most badly affected area was the Gamariguri block, where 100% of the samples had As and Fe concentrations above the WHO drinking water guideline values. In this block, the highest As and Fe concentrations were recorded 0.128 and 5.9 ppm, respectively. Tubewell water of depth 180 ± 10 ft found to be more contaminated by As and Fe with 78% and 83% of the samples were tainted with higher concentration of such toxic metals, respectively. A strong significant correlation was observed between As and Fe (0.697 at p < 0.01), suggesting a possible reductive dissolution of As?CFe-bearing minerals for the mobilization of As in the groundwater of the region.     

某集中式饮用水源地保护区土壤重金属监测与评价

采用现场采样与室内测试方法测定了某大型集中式饮用水源地一级保护区土壤中Cd、Hg、As、Pb、Cr、Cu、Zn和Ni的含量,利用污染指数法、地累积指数法和潜在生态指数法对其土壤环境质量进行了评价。结果表明,上述8种重金属都存在不同程度的超标,其中Cd超标最为严重。地累积指数法评价结果表明,研究区只有Cd、Hg存在一定污染,污染程度分别为中度污染到强污染、中度污染和中度污染到强污染。潜在生态指数法结果表明:研究区土壤样品Cd的单因子潜在生态风险指数最高,轻微、中等和较高风险等级中所占比例分别为44.7%、23.7%、31.6%;其次为Hg,有89.5%的土壤样品中Hg处于轻微生态风险水平,10.5%的土壤样品处于中等生态风险水平;土壤样品中As、Pb、Cu、Ni、Zn、Cr都处于轻微生态风险水平。Cd是研究区最主要的污染和生态风险因子,其次是Hg,说明集中式饮用水源地保护区土壤已受到个别重金属的影响。虽然目前尚不存在饮用水源地水体受污染问题,但应引起高度关注。     

Statistical analysis of arsenic contamination in drinking water in a city of Iran and its modeling using GIS

In this research, probable arsenic contamination in drinking water in the city of Ardabil was studied in 163 samples during four seasons. In each season, sampling was carried out randomly in the study area. Results were analyzed statistically applying SPSS 19 software, and the data was also modeled by Arc GIS 10.1 software. The maximum permissible arsenic concentration in drinking water defined by the World Health Organization and Iranian national standard is 10 μg/L. Statistical analysis showed 75, 88, 47, and 69% of samples in autumn, winter, spring, and summer, respectively, had concentrations higher than the national standard. The mean concentrations of arsenic in autumn, winter, spring, and summer were 19.89, 15.9, 10.87, and 14.6 μg/L, respectively, and the overall average in all samples through the year was 15.32 μg/L. Although GIS outputs indicated that the concentration distribution profiles changed in four consecutive seasons, variance analysis of the results showed that statistically there is no significant difference in arsenic levels in four seasons.     

Inorganic arsenic levels in rice milk exceed EU and US drinking water standards

Under EU legislation, total arsenic levels in drinking water should not exceed 10 microg l(-1), while in the US this figure is set at 10 microg l(-1) inorganic arsenic. All rice milk samples analysed in a supermarket survey (n = 19) would fail the EU limit with up to 3 times this concentration recorded, while out of the subset that had arsenic species determined (n = 15), 80% had inorganic arsenic levels above 10 microg l(-1), with the remaining 3 samples approaching this value. It is a point for discussion whether rice milk is seen as a water substitute or as a food, there are no EU or US food standards highlighting the disparity between water and food regulations in this respect.     

Assessment of some trace heavy metals and radioactivity concentration in water of Bendimahi River Basin (Van, Turkey)

The levels of heavy metals were determined in the water of Bendimahi River Basin, statistically analysed and compared to natural gross radioactivity concentration. Fifteen samples of water were collected from Bendimahi River and Van Lake for two seasons in 2005. Water samples were analyzed for eight trace elements and concluded together with gross-alpha and gross-beta radioactivity concentrations. Atomic absorption spectrometry (AAS) was used to determine the concentrations of heavy metals in water samples collected from Bendimahi River basin. Correlation analysis was made for radioactivity and heavy metal concentrations and the Pearson correlation coefficients between gross-alpha and gross-beta radioactivity and heavy metal were determined. The concentrations of all metals were found to be higher than WHO, EC, EPA and TSE-266 guidelines for drinking water, except for Zn and Cu. Generally, the heavy metal concentrations in water samples obtained in May and in August were found to be in sequence of Fe>Zn>Pb>Cr>Cu>Mn>Co>Cd and Fe>Zn>Cu>Pb>Cr>Mn>Co>Cd, respectively. The gross-alpha and gross-beta activity concentration varies between 0.063 and 0.782, 0.021 and 0.816 Bq l(-1) in samples collected in May, and 0.009 and 0.037, 0.081 and 3.116 Bq l(-1) in samples collected in August.     

Heavy metal contamination of drinking water in Kamrup district, Assam, India

This study was undertaken to assess the heavy metal concentration of the drinking water with respect to zinc, copper, cadmium, manganese, lead and arsenic in Kamrup district of Assam, India. Ground water samples were collected from tube wells, deep tube wells and ring wells covering all the major hydrogeological environs. Heavy metals in groundwater are estimated by using Atomic Absorption Spectrometer, Perkin Elmer Analyst 200. Data were assessed statistically to find the distribution pattern and other related information for each metal. The study revealed that a good number of the drinking water sources were contaminated with cadmium, manganese and lead. Arsenic concentrations although did not exceeded WHO limits but was found to be slightly elevated. Copper and zinc concentrations were found to be within the prescribed WHO limits. An attempt has also been made to ascertain the possible source of origin of the metals. Positive and significant correlation existing between manganese with zinc and copper indicates towards their similar source of origin and mobility. In view of the present study and the level of heavy metal contamination, it could be suggested to test the potability of the water sources before using it for drinking purpose.     

Co-occurrence profiles of trace elements in potable water systems: a case study

Potable water samples (N?=?74) from 19 zip code locations in a region of Greece were profiled for 13 trace elements composition using inductively coupled plasma mass spectrometry. The primary objective was to monitor the drinking water quality, while the primary focus was to find novel associations in trace elements occurrence that may further shed light on common links in their occurrence and fate in the pipe scales and corrosion products observed in urban drinking water distribution systems. Except for arsenic at two locations and in six samples, rest of the analyzed elements was below maximum contaminant levels, for which regulatory values are available. Further, we attempted to hierarchically cluster trace elements based on their covariances resulting in two groups; one with arsenic, antimony, zinc, cadmium, and copper and the second with the rest of the elements. The grouping trends were partially explained by elements’ similar chemical activities in water, underscoring their potential for co-accumulation and co-mobilization phenomena from pipe scales into finished water. Profiling patterns of trace elements in finished water could be indicative of their load on pipe scales and corrosion products, with a corresponding risk of episodic contaminant release. Speculation was made on the role of disinfectants and disinfection byproducts in mobilizing chemically similar trace elements of human health interest from pipe scales to tap water. It is warranted that further studies may eventually prove useful to water regulators from incorporating the acquired knowledge in the drinking water safety plans.     

Suitability assessment of groundwater for drinking, irrigation and industrial use in some North Indian villages

The study comprised suitability assessment of groundwater for drinking, irrigation, and industrial use. A total of 34 groundwater samples were collected from Rewari town and its perimeter from the land chiefly used for agriculture. Physico-chemical characterization of the samples revealed that groundwater from most of the sources was not fit for drinking owing to a high concentration of calcium, magnesium, hardness and fluoride. Suitability for irrigation, too, was low since most of the sources had high value of sodium adsorption ratio (SAR), residual sodium carbonate (RSC), soluble sodium percentage (SSP) and magnesium hazard which can render salinity and alkali hazard to soils on long term use in irrigation. No source of water was found to be suitable for industrial application since it had high concentration of calcium carbonate which can precipitate very easily. It was observed that sodium, sulphate, and chloride were the chief ions present in water and based on the abundance of ions and their correlation type, most of the groundwater samples are of sodium sulphate and/or sodium chloride type. The high concentration of the chemical constituents is attributed to the lithologic composition of the area. It was observed that the water of deep meteoric percolation type was of sodium sulphate type and the shallow of sodium chloride type.     

Potability of water sources in relation to metal and bacterial contamination in some northern and north-eastern districts of India

A total of 1094 water samples from 326 springs, 207 streams, 183 dug wells, 151 piped supplies, 90 tube wells, 75 hand pumps, 60 rivers and 2 lakes were collected from eight northern and six north-eastern districts of India. Samples were analysed to assess their potability by estimating the level of heavy metals and bacterial (coliform and faecal coliform) contaminations. Iron was found in a maximum number (53%) of water samples from hand pumps, followed by lead in 43% of the tube wells, chromium in 16% of dug wells, cadmium in 13% of streams and manganese in 7% of hand pumps above their maximum admissible concentrations (MACs). Maximum metal pollution has been observed in a considerable number of water samples from Doda, followed by Almora, Mirzapur and Bankura. Hand pump water samples exhibited maximum metal pollution followed by dug well, spring, stream and river water samples. Contamination of coliform and/or faecal coliform bacteria ranged between 41% and 67% of water samples from open water sources but it was also less, i.e. 6–15% of water samples from tube wells and hand pumps. In general, 42–85% of water samples from districts surveyed, except from Jammu (18%) and Mirzapur (27%), were found to be bacteriologically unsatisfactory. Since toxic metals and pathogenic bacteria pose a risk to public health, monitoring of drinking water sources is required.     

北京某污水处理厂出水中药物和个人护理品的污染现状

通过两次采集北京某大型污水处理厂的水样,采用HPLC-MS技术对水样中的10种PPCPs进行分析.结果显示,进水口水样中PPCPs浓度为7122.92ng/L,其中咖啡因的检出浓度最高(4490.54ng/L),污水处理厂对咖啡因的去除率大于90％(浓度为78.01ng/L).与文献报道值比较发现,该污水处理厂出水水样中PPCPs的浓度与其他国家报道的浓度基本上处于同一数量级,但污水中PPCPs的去除率都普遍低于国际水平.因此,需加强对污水处理厂水样中PPCPs的监测,完善污水处理的工艺.