平板膜MBR处理生活污水试验研究

采用平板膜MBR工艺处理小区生活污水,研究了MBR工艺对COD、BOD、NH4+-N、SS及浊度等去除效果,在进水COD、BOD平均浓度为325mg/L、274mg/L的情况下,出水达到20mg/L和8mg/L,去除率在93%以上,SS及浊度去除率达到100%和98%,NH4+-N去除率79%,出水NH4+-N小于10mg/L。通过研究系统三氮转化可知,该系统没有发生反硝化反应,出水NO2--N和NO3--N浓度较高。通过投加葡萄糖人为改变容积负荷,在容积负荷变化3.2kgCOD/m·3d情况下,系统受负荷冲击影响较小,COD去除率仍能保持在88%以上。通过对膜通量的研究发现,膜通量在连续运行的前3天变化不大,第3天后,膜通量迅速降低,第10天后膜污染达到极限,因此清洗周期设定为3～4天。     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｃｏｎｔａｉｎｓａｌｏｔｋｉｎｄｓｏｆｐｏｌｌｕｔａｎｔｓ,ｓｕｃｈａｓａｃｉｄｉｃｄｙｅｓ,ｄｉｓｐｅｒｓｅｄｙｅｓ,ｍｏｒｄａｎｔｄｙｅｓ,ａｕｘｉｌｉａｒｉｅｓ,ｓａｌｔｓａｎｄｓｏｏｎ .Ｔｈｅｅｆｆｌｕｅｎｔｓｆｒｏｍｗａｓｔｅｗａｔｅｒｔｒｅａｔｍｅｎｔｐｌａｎｔｓｆｏｒｔｒｅａｔｍｅｎｔｏｆｔｈｅｄｙｅｉｎｇｗａｓｔｅｗａｔｅｒｏｆｗｏｏｌｅｎｍｉｌｌｓｗｉｔｈｎｏｒｍａｌｂｉｏｌｏｇｉｃａｌｐｒｏｃｅ…     

膜生物反应器处理毛纺废水的中试研究

采用中试规模(10t/d)的厌氧-好氧膜生物反应器(A/O MBR)处理毛纺印染废水.当HRT为7h,进水COD、BOD₅分别为179～358mg/L和44.8～206mg/L,试验系统对COD、BODs、色度、浊度的平均去除率分别为92.1%、98.4%、60.7%、98.9%,出水水质浓度或指标值分别为20.2mg/L、1.6mg/L、25倍、0.51 NTU.出水水质指标达到建设部生活杂用水水质标准(CJ25.1-89).A/O MBR工艺处理毛纺印染废水技术可行、操作简单、易于管理,可为工业规模应用提供技术参考.     

Treatment of a dyeing wastewater from a woolen mill using an A/O membrane bio-reactor

An anaerobic/oxic membrane bioreactor (A/O MBR) was used for treatment of dyeing wastewater from a woolen mill.COD and color of the wastewater were 54-473 mg/L and 40-400 dilution time (DT) respectively. The ratio of BOD5/COD was less than 0.13. By the A/O MBR process, the average removal of COD, BOD5, color and turbidity was 82％, 96％, 71％ and 99％, respectively. The average COD, BOD5, color and turbidity of effluent was 37 nag/L, 0.8 mg/L, 40 DT and 0.44 NUT respectively. The effluent COD met the local standard of reuse water in Beijing, China. The average COD volume load of the anaerobic biological tank was 0. 0483 kgCOD/(m3·d) and that of the aeration tank of the MBR was 0. 3589 kgCOD/(m3·d). The sludge load of the MBR was 0.19 kgCOD/(kg· MLSS· d) on average and the maximum of that was 0.4 kgCOD/( kg· MLSS· d).The flux of the A/O membrane bioreactor could be remained at larger than 50 L/(h· m2· 0.1MPa). The results indicated that A/O membrane bioreactor has technical feasibility for treatment of woolen mill wastewater.     

厌氧反应器与好氧MBR组合工艺处理毛纺印染废水试验研究

采用厌氧反应器与膜生物反应器(MBR)组合工艺处理毛纺印染废水,结果表明,当进水COD、BOD₅和色度分别为128～321 mg/L、36～95 mg/L和40～70倍时,出水COD、BOD₅、色度、浊度的平均值分别为36.9 mg/L、3.7 mg/L、21倍、0.24 NTU,平均去除率分别达到80.3%%、95%、59%、99.3%,达到生活杂用水水质标准.在本研究中,开发了一种新型的利用生物反应器内液位水头重力驱动连续出水的重力出流式膜生物反应器.在保留MBR处理效率高等优点的同时,省去传统的一体式MBR出水抽吸泵及复杂的反冲洗设备.整个系统结构紧凑,投资少,操作简便.选择合适的曝气量有助于提高膜通量,且可降低膜阻力的上升速率,有利于膜污染的控制.     

颗粒活性炭对膜生物反应器脱氮性能的影响

为了考察投加颗粒活性炭(GAC)对膜生物反应器(MBR)运行过程和处理效果的影响,研究了MBR和GAC-MBR透膜压差、膜通量的变化情况和脱氮性能,并采用ASM1模型对2个反应器进行数学模拟.结果表明,MBR和GAC-MBR的运行周期分别为75,150h,说明GAC的加入能够显著减缓MBR膜污染的速度,延长MBR的运行周期.MBR和GAC-MBR氨氮浓度分别为0.5,6mg/L;硝氮浓度分别为4.5,2mg/L;总氮浓度分别为5,10mg/L,出水COD均低于20mg/L,出水能符合《城镇污水处理厂污染物排放标准(GB 18918-2002)》中的一级A标准.采用ASM1进行工艺数学模拟,模拟出水与实际测量值基本吻合,2个反应器中主要微生物为异养菌和氨氧化菌,异养菌在MBR和GAC-MBR中的质量分数分别为95.5%和97.7%;好氧氨氧化菌分别为4.4%和2.3%,说明投加颗粒活性炭能有效的缓解膜污染,并对污染物具有良好的处理效果.     

平板膜-生物反应器工程化应用研究

为了加快平板膜-生物反应器的工程化应用步伐,以上海白龙港水质净化厂400 t/d的示范工程为依托,对平板膜-生物反应器的污染物去除效果、膜污染情况和清洗效果等进行了研究。平板膜-生物反应器的出水COD在20 mg/L左右,浊度小于5 NTU,氨氮小于5 mg/L,基本满足杂用水水质标准（GB/T18920-2002）,可以回用作厂区内冲厕和绿化用水等。正交实验结果表明,对在线清洗效果影响较大的因素是曝气量和清洗点的跨膜压力,影响较小的是清洗时间;跨膜压力为45 kPa,停抽时间为2 h,曝气量为100 m3/h为在线清洗的最佳操作条件。     

垃圾渗滤液处理工程实例

利用厌氧UASB+膜生物反应器MBR+纳滤工艺处理垃圾填埋场产生的垃圾渗滤液,介绍了各处理阶段的设计、运行参数和经济技术指标,设计处理规模为100 m3/d。在进水ρ(COD)为10 000 mg/L,ρ(BOD5)为5 000 mg/L,经处理后,出水ρ(COD)达到60 mg/L,ρ(BOD5)约为20 mg/L,去除率分别达到99.4%、99.6%,且出水稳定,达到地方标准DB 11/307-2005《北京市水污染排放标准》中二级排放标准。     

气升循环分体式膜生物反应器再生回用厕所污水的研究

研究了分体浸没式膜生物反应器及其应用于厕所污水的再生回用.试验结果表明,在人水浓度COD440～970mg/L、BOD₅ 307～612mg/L、NH₃-N59～111mg/L的情况下,出水水质稳定,平均COD＜47mg/L、BOD₅＜8.5mg/L、NH₃-N＜20mg/L,处理水质达到建设部颁布的生活杂用水回用标准.研究了动力学参数污泥负荷、容积负荷和HRT对出水COD的影响,确定本试验较佳的污泥负荷和容积负荷分别为0.1kg/(kg·d)和1kg/(m³·d),HRT为7～8h.本文对污泥浓度、温度和产水时间与间歇时间比对膜通量的影响进行了测定与探讨.     

一种垃圾渗滤液的处理技术

本文采用厌氧反应器UASB+膜生物反应器MBR+纳滤工艺处理垃圾填埋场废水,设计处理能力为100m3/d,在进水CODs:和BODs分别为10 000 mg/L和5 000 mg/L时,经处理后,出水CODc:和BODs分别为60mg/L和20mg/L,其去除率分别为99.4%和99.6%,且出水稳定,达到了<北京市水...     

SAF-化学絮凝-微滤膜组合工艺处理高浓度生活污水的试验研究

采用SAF-化学絮凝-微滤分离膜组合工艺对高浓度生活污水进行处理.SAF处理系统对污染物的去除效果良好,CODCr,BOD5,SS和NH4 -N的去除率分别为92%,93%,90%和98%.SAF生物处理系统的出水再经化学絮凝和微滤分离膜深度处理后,CODCr,BOD5,NH4 -N,PO43--P的浓度分别低于40 mg/L,10mg/L,4mg/L,0.3mg/L;浊度小于0.5NTU,色度小于10度.试验结果表明该组合工艺处理后的污水水质优良,可满足生活杂用和市政杂用.     

兼氧型MBR工艺对污泥自消化效果的研究

研究了兼氧型MBR工艺中,当溶解氧控制在0.1～3.0 mg/L时,兼性厌氧菌和厌氧菌所占比例达80%。实验进水COD浓度为60～600 mg/L,COD去除率平均达93%;MLVSS浓度一直保持稳定,平均值为11 090 mg/L,而无机灰分浓度逐渐积累,实验开始时为3 107 mg/L,实验结束时达5 830 mg/L。结果表明,兼氧型MBR工艺可实现污泥自消化,不排放有机性污泥。兼氧型MBR工艺还对膜组件有一定自清洁作用,运行周期可达4个月。实验证明,兼氧型MBR工艺具有处理效率高、不排放有机污泥以及减轻膜污染的特点,是一种创新性的污水处理技术。     

平板陶瓷膜深度处理石化废水试验研究

采用平板陶瓷膜中试装置处理石化废水,分析了处理效果与膜污染情况,获得了平板陶瓷膜稳定运行条件下的工艺参数。结果表明:在COD为50~100 mg/L、浊度为2~11 NTU的进水条件下,平板陶瓷膜出水COD与浊度分别为20~42 mg/L和0.05~0.2 NTU,与双层过滤器+中空纤维超滤工艺出水水质较为接近;在运行通量40 L/(m 2·h)、反洗周期45 min、反洗时间60 s的条件下,采用浓度为100~150 mg/L的次氯酸钠每7小时进行1次化学清洗,平板陶瓷膜系统运行较为稳定。     

Pollutants removal and simulation model of combined membrane process for wastewater treatment and reuse in submarine cabin for long voyage

A laboratory scale test was conducted in a combined membrane process (CMP) with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage. Removal performance of chemical oxygen demand (COD), ammonia nitrogen (NH4 +-N), turbidity and anionic surfactants (LAS) was investigated under di erent conditions. It was observed that the e uent COD, NH4 +-N, turbidity and LAS flocculated in ranges of 0.19–0.85 mg/L, 0.03–0.18 mg/L, 0.0–0.15 NTU and 0.0–0.05 mg/L, respectively in spite of considerable fluctuation in corresponding influent of 2120–5350 mg/L, 79.5–129.3 mg/L, 110–181.1NTU and 4.9–5.4 mg/L. The e uent quality of the CMP could meet the requirements of mechanical water and hygiene water according to the class I water quality standards in China (GB3838-2002). The removal rates of COD, NH4 +-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradation is indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network (BPNN) theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4 +-N was 5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The results indicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4 +-N, turbidity and LAS. It also suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters in submarine.     

混凝-MBR组合技术净化洗车废水试验研究

研究混凝-MBR组合技术净化洗车废水,首先对该技术净化CODcr、UV254、NH3 -N和浊度的效果进行了考察,实验结果表明,当废水温度大于22℃时、溶解氧浓度大于4.8 mg/L时、pH值在6到8之间的条件下,该组合技术对CODcr、NH3 -N和浊度的净化效果较好,平均净化率分别达到90.2%、96.4%和98%以上,高于传统MBR技术和常规技术,出水CODcr约为20 mg/L,NH3 -N基本在0.7 mg/L以下,浊度也小于0.5NTU,水质优于中国建设部生活杂用水水质标准( CJ25.1-89).     

臭氧-MBR工艺深度处理印染废水中试研究

采用臭氧-膜式生物反应器(MBR)工艺对某工业园印染废水二级生化处理出水进行了深度处理,达到企业回用水要求。结果表明,在进水COD低于100 mg/L、色度为40倍的条件下,当臭氧投加量为15～20 mg/L、MBR的水力停留时间为4～6 h、气水比为15∶1时,出水COD<40 mg/L、色度为2倍,出水水质可满足企业对回用水的水质要求。     

微电解/A/O工艺处理浆纱废水的试验研究

研究采用微电解/A/O工艺处理浆纱废水。试验结果表明:经过微电解处理后的废水可生化性得到明显改善;经过系统处理后,出水COD和BOD5浓度分别为126 mg/L和42 mg/L,COD和BOD5的总去除率分别达到94.5%和73.8%,出水符合国家污水综合排放标准。     

抗生素化学合成生产废水可生化性改善试验研究

采用水解酸化与Fenton试剂分别处理高浓度抗生素化学合成废水的厌氧出水,并采用MBR验证其生化性的改善。试验表明:在废水ρ(COD)平均为4 084 mg/L时,水解酸化COD去除率平均为26.2%,ρ(BOD5)/ρ(COD)从0.23提高到0.31,但无法保证MBR出水ρ(COD)<120 mg/L。Fenton试剂反应条件为:ρ(H2O2)=5 000 mg/L,ρ(Fe2+)=4 000 mg/L,pH=7,反应时间1 h,COD去除率达50%。混合废水经MBR处理后,出水ρ(COD)平均为98.4 mg/L,可稳定达《制药工业水污染物排放标准》。     

United membrane biological reactor in the treatment of wastewater

The united membrane biological reactor(UMBR) was studied for the treatment of some simulate and municipal wastewater. The removal efficiency for COD and turbidity are greater than 80% and 99% respectively. Effluent COD is less than 100 mg/L while turbidity less than 5. The removal of LAS in bath wastewater is greater than 70%. In treatment of dinning-hall wastewater, removal of fatty oil is greater than 90%, and its concentration in effluent is less than 5 mg/L. The match of biological reactor and the membrane separation component were calculated. The stable performance of wastewater treatment can be maintained by the optimization of operation conditions and the eleanout of membranes.     

膜生物膜工艺处理含盐工业废水

采用了膜生物膜工艺处理含盐羧甲基纤维素生产废水。接种污泥为普通污泥,经驯化使其适应含盐废水,在污泥驯化阶段,生物膜表现出极佳的盐度冲击后恢复能力。通过较长的水力停留时间(5～15 d)和较低的COD有机负荷(平均1.6 kg/(m3·d)左右),生物膜COD去除率基本达90%。膜池内,悬浮固体浓度基本保持在5 000 mg/L以内;通过聚偏氟乙烯中空纤维膜过滤,出水悬浮固体浓度保持在5 mg/L以内。膜污染可通过重复的气水反洗和定期的化学清洗得以缓解。