电解催化降解有机污染物机理的高效液相色谱研究(Ⅰ)——原理和实验结果

目前对电解催化降解有机污染物的机理存有争议。本文用苯酚作为 HO·的捕集剂 ,采用高效液相色谱法对形稳阳极电解处理有机废水的机理进行了研究 ,表明在电解过程中产生了对苯二酚和邻苯二酚等羟基化产物 ,这正是HO·和芳环类化合物之间的特征反应。实验结果说明电解催化体系能够产生氧化能力极强的 HO· ,可以氧化降解废水中的有机污染物 ,即有机污染物以间接氧化的方式降解 ,这是电解催化氧化技术的主要机理。由于上述原因 ,电解催化氧化技术也属于高级氧化技术的范畴     

一种新型电化学体系降解苯酚的机理研究

通过使用自制的碳聚四氟乙烯(CPTFE)气体扩散电极作为阴极,TiIrO2RuO2材料为阳极,研究了隔膜电解槽中电化学降解苯酚的机理.结果表明,在阴极室,CPTFE气体扩散阴极通过外界曝气提供的O2在阴极还原产生H2O2,电解80min后H2O2的稳定浓度达到8.3mg·L-1.采用电子自旋共振法(ESR)在阴极室中检测到羟自由基(HO·)的存在.采用高效液相色谱(HPLC)在阴极室检测到羟基加合物对苯二酚,证明HO·参与了苯酚的降解过程.在该电化学体系中苯酚的降解是在阳极直接、间接氧化及阴极产生的H2O2、HO·的氧化共同作用下完成的.阴极室检测到了对苯二酚、苯醌等苯环化合物和顺丁烯二酸、反丁烯二酸、丙烯酸、丙二酸、草酸、乙酸、甲酸等短链羧酸,据此提出了苯酚降解的可能历程,并对阴、阳极室中苯酚降解途径之间的差异进行了初步比较.     

掺锑二氧化锡多孔钛阳极对苯酚的催化氧化

研究了掺锑二氧化锡多孔钛基阳极对苯酚的催化氧化,分析了溶液pH值、温度、苯酚初始浓度、盐含量及表观电流密度对苯酚降解效果的影响,并对苯酚的氧化降解历程及动力学特征进行了讨论,紫外分光光度法、高效液相色谱法（HPLC）及化学方法（COD）测试结果表明,苯酚的催化降解中间产物有对苯二酚、苯醌、丁烯二酸、草酸等,最终产物为二氧化碳．苯酚在掺锑二氧化锡多孔钛阳极上的降解动力学方程符合表观拟一级反应。     

水相中苯酚光催化降解的全额光子效率

为定量评价光催化反应器的性能,利用主辐射波长为207 nm的KrBr*准分子灯降解水相中的苯酚,测定了光解和光催化降解2种体系中苯酚和TOC去除率,并计算了苯酚降解的ξ_g(全额光子效率),探讨了其影响因素. 结果表明:①延长反应时间、加入适量催化剂、降低初始c(苯酚)能提高苯酚和TOC去除率. 采用动力学模型对苯酚的降解进行拟合,表明光解和光催化降解体系中苯酚的降解均符合准一级动力学模型. ②加入催化剂和提高初始c(苯酚)均可以获得较高的ξ_g,而光源的辐射功率与ξ_g没有线性相关性;在辐射功率为0.76 W、初始c(苯酚)为1.10 mmol/L、催化剂投加量(以ρ计)为0.8 g/L的条件下,ξ_g为5.56%. ③采用高效液相色谱对光催化降解体系中生成的中间产物的变化规律进行研究发现,4种中间产物表现为c(对苯二酚)＞c(邻苯二酚)＞c(对苯醌)＞c(间苯二酚);通过建立苯酚及中间产物的拟一级降解动力学模型,证实苯酚光催化降解历程为苯酚→芳香烃中间产物→最终产物.      

Pd/C气体扩散电极用于电生成H2O2降解苯酚的研究

采用自制的Pd/C气体扩散阴极和Ti/IrO2/RuO2阳极,在无隔膜电解槽中对苯酚模拟废水降解效果及机制进行了研究,采用电子自旋共振法(ESR)对电解体系中产生的羟自由基(·OH)进行了检测.结果表明,在Pd/C气体扩散体系中掺杂Pd催化剂可以促进H2 O2的生成(H2 O2的稳定浓度是7.5 mg/L),有利于·OH的产生.经电化学氧化处理120 min后,苯酚和COD的去除率分别达到97.2%和50%,表明在电催化氧化过程中苯酚被氧化生成了大量低分子量中间产物.废水的BOD5/COD值达到0.73是处理前的9.1倍,苯酚废水的可生化降解性通过电化学氧化处理后显著提高.在该电化学体系中苯酚的降解是在阳极直接、间接氧化及阴极产生的H2 O2、·OH的氧化共同作用下完成的.通过对紫外扫描光谱图的分析推断出苯酚在电解过程中有醌类物质生成;由GC-MS检测到了邻苯二酚、对苯二酚、苯醌等芳香族化合物和己二酸、顺丁烯二酸、反丁烯二酸、丁二酸、丙二酸、乙二酸等短链羧酸,据此提出了苯酚降解的可能历程.     

苯酚在氯离子体系中的电化学氧化研究

研究了用Ti/RuO2-IrO2三元电极作阳极电解处理人工合成苯酚废水时Cl-初始浓度对处理效果的影响。结果表明,在一定的电解时间范围内苯酚在阳极上的电化学氧化符合一级动力学关系;废水中Cl-的初始浓度越大,苯酚完全被电化学氧化所需的时间也越短,其表观速度常数越大,电解中间体的生成和降解速率也越大。采用HPLC、GC/MS等方法鉴定出苯酚在Cl-体系下降解的中间产物主要有4-氯苯酚,1-氯苯酚,2,4-二氯苯酚,2,6二氯苯酚,2,4,6-三氯苯酚、各种短链脂肪酸及氯代醇等;最终产物是CO2、CHCl2和CHCl3。依此推导出了苯酚在Cl-体系下电化学降解的途径。     

苯酚降解菌红球菌PNAN5菌株(Rhodococcus sp.strain PNAN5)的分离鉴定、降解特性及其开环双加氧酶性质研究

分离到一株能以苯酚、苯甲酸、对甲酚、萘为唯一碳源和能源生长、具有同时降解单环和双环芳烃能力的细菌菌株,经生理生化、16SrRNA基因序列分析等鉴定为红球菌PNAN5菌株(Rhodococcussp.strainPNAN5).在实验条件下和在温度为20～40℃、pH7 0～9 0范围内菌株PNAN5降解苯酚的效率保持在80%～100%之间,苯酚浓度在2～10mmol·L-1范围内变化对降解效率没有明显的影响.该菌株通过邻苯二酚1,2 双加氧酶催化的开环途径降解芳烃,不同于已知的浑浊红球菌(R.opacus)是通过邻苯二酚2,3 双加氧酶催化芳烃降解.以细胞裂解液测定该酶的酶促反应动力学常数Km值为35 94μmol·L-1,Vmax为0 84μmol·L-1·min-1·mg-1.     

TiO2光催化联合技术降解苯酚机制及动力学

主要研究了TiO2光催化体系结合H2O2或外加电催化(EC)体系对苯酚催化降解效率的影响,评价比较TiO2/UV、H2O2/UV、TiO2/UV/H2O2、TiO2/UV/EC体系下苯酚降解机制及动力学.结果表明,TiO2/UV/H2O2和TiO2/UV/EC体系下苯酚降解效率明显高于TiO2/UV体系,当苯酚溶液pH值为6,TiO2质量浓度0.2 g·L-1,紫外光照2 h,光催化降解效果达到86%,当电流密度为12 mA·cm-2,则苯酚可达到100%去除.比较了不同催化体系下的能量利用率,苯酚降解15 min,TiO2/UV/EC体系能量利用率最大为0.030 6 g·(kW·h)-1,其能量消耗为0.0640 kW·h-1,说明采用TiO2/UV/EC体系能更多地利用能量降解苯酚.通过不同催化体系下中间产物分析,建立苯酚及其中间产物对苯二酚、邻苯二酚和苯醌的拟一级降解动力学模型,通过模型验证各催化体系下苯酚的降解历程,同时也说明了TiO2/UV/EC体系有利于苯酚及其中间产物的降解.     

铁铜催化剂非均相Fenton降解苯酚及机制研究

通过浸渍法制备了负载于活性炭(AC)上的金属催化剂Fe/AC、Cu/AC和Fe-Cu/AC,并通过X射线衍射(XRD)、物理吸附仪及X射线光电子能谱(XPS)对其进行了表征.研究了非均相Fenton反应催化H2O2降解苯酚废水的工艺参数,并通过中间产物分析和电子自旋共振谱(ESR)探讨了过程反应机制.实验表明,Cu/AC催化剂中铜主要以CuO形式存在,Fe/AC中铁以多价态形式存在,以无定形形态分散于活性炭中.Fe/AC、Cu/AC和Fe-Cu/AC催化过氧化氢降解苯酚60 min内降解率分别达到96.7%、77.5%和99%;Cu/AC和Fe-Cu/AC催化剂中活性组分铜和铁有一定溶出,而Fe/AC中活性组分铁溶出很少,苯酚降解主要是以非均相催化为主,同时在三轮循环实验后的苯酚降解率仍然高达93%以上,显示了良好的催化稳定性.在优化条件pH=3、T=303 K及初始H2O2为4.38 mmol.L-1下,Fe/AC催化过氧化氢对苯酚和TOC去除率分别达到97%和53%,没有催化剂时苯酚几乎不降解.ESR结果表明Fe/AC催化过氧化氢产生了羟基自由基,证明苯酚降解是以羟基自由基氧化为主;通过高效液相色谱(HPLC)检测苯酚降解中间产物主要有邻苯二酚、对苯二酚和对苯醌,推测苯酚降解途径主要为邻位和对位的羟基取代反应.     

高效复合菌群JHD降解苯酚的特性及其动力学研究

为了获得能降解苯酚的高效微生物菌群,研究了不同条件(温度、pH、接种量、振荡速率及初始苯酚浓度等)对复合菌群JHD降酚性能的影响.结果表明,32℃、pH=7.0、接种量为10%和振荡速率为150 r·min-1,初始苯酚浓度为1000 mg·L-1时降解苯酚16 h,降酚率高达99.97%,残余苯酚浓度低于0.28 mg-L-1,远低于国家一级排放标准.采用Andrews方程对复合菌群JHD降解苯酚的过程进行拟合,其动力学参数为qmax=0.41 h-1,K=55.44 mg·L-1,Ki=970.06 mg·L-1,复合菌群JHD降解苯酚的最佳初始苯酚浓度为231.90 mg·L-1,实验数据与该动力学方程拟合较好.     

Enhanced photocatalytic activity of TiO2 by surface fluorination in degradation of organic cationic compound

Experiments were carried out to investigate the influence of TiO2 surface fluorination on the photodegradation of a representative organic cationic compound, Methylene Blue （MB）. The eleetropositive MB shows poor adsorption on TiO2 surface; its degradation performs a HO. radical-mediated mechanism. In the F-modified system, the kinetic reaction rate enlarged more than 2.5 fold that was attributed mainly to the accumulating adsorption of MB and the increased photogenerated hole available on the F-modified TiO2 surface.     

形稳阳极电解处理有机废水的机理研究

采用简便易行的方法对用形稳阳极电解处理有机废水的机理进行了研究，表明在电解过程中能够产生氧化能力极强的ＨＯ·自由基，可以氧化降解废水中的有机污染物，即有机污染物以间接氧化的方式降解，这是电解催化氧化技术的主要机理。由于上述原因，电解催化氧化技术也属于高级氧化技术的范畴。     

Experimental study on agitated drying characteristics of sewage sludge under the effects of different additive agents

Drying experiments of dewatered sewage sludge（DSS） were conducted on a agitated paddle dryer, and the effects of additive agents, i.e., CaO, pulverized coal（PC）, heavy oil（HO）, and dried sludge（＂DS＂ through back mixing） on the agitated drying characteristics of DSS were investigated. The results indicated that CaO can significantly increase the drying rate of DSS.The drying rate at CaO/DSS（mass ratio） = 1/100 was 135% higher than that of CaO/DSS = 0.Pulverized coal has no obvious effect on drying rate, but the increase of PC/DSS can promote breaking up of sludge lump. Heavy oil was found to be slightly effective in improving the drying rate of DSS in the examined experimental range of HO/DSS = 0-1/20. It is also found that HO can reduce the torque of the dryer shaft, due to its lubrication effect. Back mixing of DS was found to be effective in alleviating the unfavorable effect of the lumpy phase by improving the mixing effect of the paddle dryer. There was a marked increase of drying rate with an increase of the DS/DSS in the experimental range of DS/DSS = 0-1/3.     

Determination of photochemically-generated reactive oxygen species (ROS) in natural water

Reactive oxygen species (ROS) can be produced by interactions between sunlight and light-absorbing substances in natural water environment. ROS may participate in the indirect photolysis of trace organic pollutants, therefore resulting in the changing of their environmental fates and ecological risks in natural water system. Bisphenol A (BPA), an endocrine-disrupting chemical, exits widely in natural water. The photodegradation of BPA promoted by ROS (·OH, 1O2, HO2·/O2·-) which were produced on the excitation of ubiquitous constituents (such as nitrate ion, humic substances and Fe(III)-oxalate complexes) in natural water under simulated solar radiation was investigated. Both molecular probe method and electron spin resonance (ESR) test were used for the determine the characterization of generated ROS. It was found that ·OH was photochemically produced with the presence of nitrate ion, humic substances and Fe(III)-oxalate complexes and 1O2 was produced with the presence of humic substances. The steady-state concentrations of ·OH was 1.27×10-14 mol/L in nitrate ion, and the second-order rate constant of BPA with ·OH was 1.01×1010L/( mol·s).     

穿透式碳纳米管电极的制备及其高效降解水中抗生素的性能和机理

为实现水中四环素类抗生素的高效降解,本文设计开发了一种基于电活性碳纳米管(CNT)电极的穿透式电芬顿系统,采用水热法制得纳米铁和二硫化钼共修饰的CNT阴极材料(Fe-MoS₂@CNT),分析不同因素对电芬顿催化降解四环素性能的影响. 结果表明:基于改性CNT电极的穿透式电芬顿系统对四环素表现出良好的去除性能,电压和流速等对四环素的降解动力学具有显著影响. 该系统的最优试验条件:Fe掺杂量为0.3 mmol/L、外加电压为-2.5 V、流速为0.85 cm3/(min·cm2). 在最优试验条件下,反应60 min内四环素的降解率可达到95%,羟基自由基为主导的活性物种. 连续运行240 min后,该系统对四环素的降解率仍保持在85%以上,且在实际湖水环境水基质中对四环素降解率也可达到87.2%. 研究显示,Fe-MoS₂@CNT膜电极具有优异的催化性能及可重复利用性,可以高效降解水中四环素类抗生素.      

Mechanism of enhanced removal of quinonic intermediates during electrochemical oxidation of Orange Ⅱ under ultraviolet irradiation

The effect of ultraviolet irradiation on generation of radicals and formation of intermediates was investigated in electrochemical oxidation of the azo-dye Orange I1 using a TiO2-modified β- PbO2 electrode. It was found that a characteristic absorbance of quinonic compounds at 255 nm, which is responsible for the rate-determining step during aromatics degradation, was formed only in electrocatalytic oxidation. The dye can be oxidized by either HO radicals or direct electron transfer. Quinonic compounds were produced concurrently. The removal of TOC by photo-assisted electrocatalytic oxidation was 1.56 times that of the sum of the other two processes, indicating a significant synergetic effect. In addition, once the ultraviolet irradiation was introduced into the process of electrocatalytic oxidation, the degradation rate of quinonic compounds was enhanced by as much as a factor of two. The more efficient generation of HO radicals resulted from the introduction of ultraviolet irradiation in electrocatalytic oxidation led to the significant synergetic effect as well as the inhibiting effect on the accumulation of quinonic compounds.     

Conversion characteristics and mechanism analysis of gaseous dichloromethane degraded by a VUV light in different reaction media

The photodegradation of gaseous dichloromethane (DCM) by a vacuum ultraviolet (VUV) light in a spiral reactor was investigated with different reaction media and initial concentrations. Through the combination of direct photolysis, O₃ oxidation and HO. oxidation, DCM was ultimately mineralized into inorganic compounds (such as HCl, CO₂, H₂O, etc.) in the air with relative humidity (RH) of 75%-85%. During the photodegradation process, some small organic acids (including formic acid, acetic acid) were also detected and the intermediates were more soluble than DCM, providing a possibility for its combination with subsequent biodegradation. Based on the detected intermediates and the confirmed radicals, a photodegradation pathway of DCM by VUV was proposed. With RH 75%-80% air as the reaction medium, the DCM removal followed the second-order kinetic model at inlet concentration of 100-1000 mg/m³. Kinetic analysis showed that the reaction media affected the kinetic constants of DCM conversion by a large extent, and RH 80% air could cause a much lower half-life for its conversion. Such results supported the possibility that VUV photodegradation could be used not only for the mineralization of DCM but also as a pretreatment before biodegradation.     

Atmospheric and kinetic studies of OH and HO2 by the FAGE technique

A new FAGE setup has recently been built at the University of Lille, France. It permits the quantification of OH and HO₂ in the atmosphere with a detection limit of 3×10⁵ molecules/(cm³·min) for OH and 1×10⁶ molecules/(cm⁵·min) for HO₂. Its coupling to a photolysis cell enables the measurement of the total reactivity of the hydroxyl radical in ambient air and kinetic studies in laboratory. Two configurations have been considered: one with the photolysis cell at 90° to the FAGE nozzle, the other on line with the FAGE nozzle. The two configurations have been tested and validated by measuring the well known rate constants of OH with CH₄, C₃H₈ and CO. The advantages and drawbacks of each configuration have been evaluated. The “on line” configuration limits losses and permits measurements over a larger reactivity range but is affected by OH formation from the laser beam striking the FAGE nozzle, thus limiting the ability to carry out energy dependence studies which can, in contrast, be successfully performed in the 90° configuration.     

Experimental study on agitated drying characteristics of sewage sludge under the effects of different additive age

Drying experiments of dewatered sewage sludge (DSS) were conducted on a agitated paddle dryer, and the effects of additive agents, i.e., CaO, pulverized coal (PC), heavy oil (HO), and dried sludge ("DS" through back mixing) on the agitated drying characteristics of DSS were investigated. The results indicated that CaO can significantly increase the drying rate of DSS. The drying rate at CaO/DSS (mass ratio) = 1/100 was 135% higher than that of CaO/DSS = 0. Pulverized coal has no obvious effect on drying rate, but the increase of PC/DSS can promote breaking up of sludge lump. Heavy oil was found to be slightly effective in improving the drying rate of DSS in the examined experimental range of HO/DSS = 0-1/20. It is also found thatHOcan reduce the torque of the dryer shaft, due to its lubrication effect. Back mixing of DS was found to be effective in alleviating the unfavorable effect of the lumpy phase by improving the mixing effect of the paddle dryer. There was a marked increase of drying rate with an increase of the DS/DSS in the experimental range of DS/DSS = 0-1/3.