氮掺杂TiO_2可见光光催化剂的制备及性能

以尿素和钛酸丁酯为原料,通过溶胶-凝胶法低温下制备了高可见光催化活性的氮掺杂TiO2（NDT）光催化剂,采用XRD、TEM、BET和UV-Vis DRS等测试手段对其进行了表征,并在自制光催化反应器中降解甲基橙评价了样品的光催化活性。结果表明,当氮与钛的摩尔比为0.5∶1时,350℃焙烧的样品（NDT350）具有最佳的可见光光谱吸收和光催化活性,该催化剂为锐钛矿晶相,平均粒径为21 nm,比表面积为89.13 m2/g。可见光辐照下,NDT350降解甲基橙的表观反应速率常数为1.381×10-2min-1,是商业P25催化剂的16.85倍。NDT350优良的可见光催化活性与其大的比表面积和强烈的可见光光谱吸收有关。     

The preparation of Zn2+-doped TiO(2) nanoparticles by sol-gel and solid phase reaction methods respectively and their photocatalytic activities

The photocatalytic oxidation of the organic pollutants with TiO(2) as photocatalyst has been widely studied in the world, and many achievements have been made. The degradation of pollutants is highly related to the photocatalytic activity of TiO(2). It is demonstrated that doping ions to TiO(2) is one way to enhance the photocatalytic activity of TiO(2). In this paper, Zn(2+)-doped TiO(2) nanoparticles were prepared through sol-gel and solid phase reaction methods, characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by sol-gel method is close to that of pure TiO(2) particles, however, the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by solid phase reaction method is much higher than that of pure TiO(2) particles. The most efficient degradation of Rhodamine B was found with TiO(2) particles doped with 0.5% Zn(2+) in mole and calcined at 500 degrees C. Also the reason for the enhancement of the photocatalytic activity of TiO(2) by Zn(2+) doping through solid phase reaction method was discussed.     

Photocatalytic degradation of dyes on a magnetically separated photocatalyst under visible and UV irradiation

A novel kind of magnetically separable photocatalyst of TiO2/SiO2/gamma-Fe2O3 (TSF) is prepared. Scanning tunnel microscope (STM) and X-ray diffractometer (XRD) were used to characterize the structure of the photocatalyst. In the TSF photocatalyst, a TiO2 shell is for photocatalysis, a gamma-Fe2O3 core as a carrier is for separation by the magnetic field and a SiO2 membrane between the TiO2 shell and the gamma-Fe2O3 core is used to weaken the adverse influence of gamma-Fe2O3 on the photocatalysis of TiO2. Three kinds of dyes, Fluoresein, Orange II and Red acid G, were used to examine the photocatalytic activity of TSF. Due to strong UV adsorption of the gamma-Fe2O3, the photocatalytic activity of TSF was lower than that of the pure TiO2. Deducting the light absorption of the gamma-Fe2O3 particles, the photocatalytic activity of TSF was found to be higher than that of the P25 under UV irradiation. On the other hand, the photocatalytic activity of TSF under visible irradiation was much lower than that of the P25 TiO2 even deducting the visible light absorption of the gamma-Fe2O3 particles. Differences in the photocatalytic mechanisms under UV and visible irradiation lead to the differences in the photodegradation characteristics of dyes on TSF. The recycled TSF exhibited a good repeatability of photocatalytic activity.     

附载型复合光催化剂TiO2·SiO2/beads降解有机磷农药

研究以四异丙醇钛 [Ti( iso- O C3 H7) 4]、硅酸乙酯为原料 ,以空心玻璃微球为载体 ,用溶胶—凝胶法制备可漂浮附载型复合光催化剂 Ti O2 · Si O2 / beads的过程 ,利用附载型复合光催化剂降解有机磷农药。结果表明 ,复合型光催化剂 Ti O2 · Si O2 摩尔比存在最佳值 ,n ( Ti O2 ) / m ( Si O2 ) =30 / 70时 ,光催化剂活性最高 ,其活性是同样降解条件下、同样含量 Degussa P- 2 5Ti O2 的 2倍左右。该光催化剂比表面大 ,吸附性强。并用 XRD和 SEM对附载型复合光催化剂进行表征     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

外负载Ce-TiO_2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭（AC）为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明：外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

V/Ce共掺杂TiO2光催化降解甲醛的实验研究

采用溶胶-凝胶法制备了不掺杂、V掺杂、Ce掺杂、V/Ce共掺杂纳米TiO2光催化剂,并将其分别负载于瓷砖上,利用X射线衍射分析（XRD）和扫描电镜分析（SEM）技术对薄膜样品的结构和形貌进行了表征。通过对甲醛的降解实验评价光催化剂的光催化活性。实验结果表明,光催化剂的负载量、共掺杂离子的掺杂量、掺杂配比、煅烧温度影响纳米TiO2的光催化活性。V/Ce共掺杂TiO2光催化剂产生了协同效应,其光催化活性优于纯TiO2和单掺杂TiO2样品。     

溴掺杂TiO2光催化剂的制备与性能研究

以KBr和Ti（SO4）2为原料,通过水热法制备了高催化活性的溴掺杂纳米TiO2（Br-TiO2）光催化剂,利用XRD、XPS、TEM、BET和UV-Vis DRS等测试手段对其进行了表征。通过苯酚降解实验评价了Br-TiO2的光催化活性。结果表明,700℃焙烧、溴与钛的摩尔比为0.35∶1时,Br-TiO2具有最佳光催化活性。该催化剂为晶体发育完整的锐钛矿相TiO2,粒径平均大小为50 nm,比表面积为16.81 m2/g,在紫外区的吸收得到加强,光催化能力优于Degussa P-25。确定了降解苯酚的最佳条件：催化剂投加量为0.5 g/L,苯酚初始浓度为10 mg/L,pH值为6.0。     

大尺寸大孔径TiO_2/SiO_2光催化剂的制备及甲醛去除研究

以大孔径SiO2为载体,通过钛酸丁酯溶液的浸渍、原位水解以及高温煅烧制备出大尺寸、大孔径的TiO2/SiO2光催化剂。利用自制空气净化装置对室内甲醛的清除进行研究,分别考察了TiO2的百分含量、紫外光光强、温度、湿度和空气流量等不同条件下TiO2/SiO2光催化剂对除去甲醛效率的影响。结果表明,反应温度从10～50℃依次升高,去除率逐渐下降。在相对湿度为50%,TiO2负载率为55.6%,流量为8 m3/h时,甲醛的最佳除去率达96.5%;经过7周时间的考察,发现TiO2/SiO2光催化剂的催化活性没有明显的下降。     

Enhanced photocatalytic degradation of VOCs using Ln3+-TiO2 catalysts for indoor air purification

Two types of lanthanide ion-doped titanium dioxide (Ln3+-TiO2) catalysts including La3+-TiO2 and Nd3+-TiO2 were prepared by a sol-gel method. The effects of the lanthanide ion doping on the crystal structure, surface area, adsorption properties, pore size distribution, and surface chemical state of the catalysts were investigated by means of XRD, BET, and XPS. As results, the crystal size decreased significantly, while the specific surface area, t-plot total surface area, micropore volume, and the total pore volume increased owing to the lanthanide ion doping. The nitrogen adsorption-desorption isotherms of the catalysts showed that the N2 adsorption ability of the Ln3+-TiO2 catalysts was better than the TiO2 catalyst. Among them, the 0.7% Ln3+-TiO2 catalysts demonstrated the highest adsorption ability. The photocatalytic activity of the catalysts was investigated in the experiments of the photocatalytic degradation of benzene, toluene, ethylbenzene and o-xylene (BTEX) in a gaseous phase. The photocatalytic efficiency of the TiO2 catalysts with the lanthanide ion doping was remarkably enhanced by BTEX removal. The 1.2% Ln3+-TiO2 catalysts achieved the highest photocatalytic activity. The enhanced photodegradation of BTEX is possibly due to the improved adsorption ability and the enhanced electron-hole pairs separation due to the presence of Ti3+ on the surface of Ln3+-TiO2 catalysts and the electron transfer between the conduction band/defect level and lanthanide crystal field state.     

Effect of ZnFe2O4 doping on the photocatalytic activity of TiO2

The photocatalytic oxidation of the organic pollutants with the TiO2 as photocatalyst has been widely studied in the world, and many achievements have been got. The degradation of pollutants is highly related with the photocatalytic activity of TiO2. It is demonstrated that doping ions or oxides to TiO2 is one way to enhance the photocatalytic activity of TiO2. In this paper, the ZnFe2O4-doped TiO2 nanoparticles were prepared from butyl titanate by a sol-gel method and characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results showed that when TiO2 was doped with ZnFe2O4, its particle size will decrease and its crystal structure will partly transform from anatase to rutile. The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that doping ZnFe2O4 to TiO2 will enhance the photocatalytic activity of TiO2 and that ZnFe2O4-doped TiO2 in the coexistence of anatase and rutile has higher efficiency for the degradation of Rhodamine B than that in the anatase phase alone. Also the different role of O2 in the direct photolysis and photocatalysis of Rhodamine B was discussed.     

TiO2光催化对微滤去除腐殖酸的膜污染控制研究

着重研究了不同紫外灯光源和照射时间条件下，TiO2光催化（PCO）对微滤去除腐殖酸过程中的膜污染控制，并探讨了膜污染的控制机理。研究结果表明，TiO2光催化能有效提高微滤对腐殖酸的去除，同时降低膜通量的下降，起到有效控制膜污染的作用。进一步的实验分析表明，TiO2光催化控制膜污染的主要机理在于将腐殖酸降解为易于被TiO2吸附的小分子量物质，吸附腐殖酸降解产物后的TiO2聚合颗粒粒径增大，易于在膜表面形成更为松散的沉积层，并使膜污染从以膜孔堵塞和沉积层污染为主转化为以沉积层污染为主的可逆性污染。     

Photocatalytic degradation of mixed gaseous carbonyl compounds at low level on adsorptive TiO2/SiO2 photocatalyst using a fluidized bed reactor

An adsorptive silica-supported titania photocatalyst TiO(2)/SiO(2) was prepared by using nanosized titania (anatase) immobilized on silica gel by the sol-gel technique with the titanium tetra isopropoxide as the main raw material and acetic acid as the acid catalyst. Meanwhile the structure and properties of the TiO(2)/SiO(2) photocatalyst were studied by means of many modern analysis techniques such as TEM, XRD, and BET. Gas-solid heterogeneous photocatalytic decomposition of four carbonyl compounds mixture at low concentration levels over ultraviolet irradiated TiO(2)/SiO(2) photocatalyst were carried out with high degradation efficiencies in a coaxial triple-cylinder-type fluidized bed photocatalytic reactor, which provided efficient continuous contact of ultraviolet photons, silica-supported titania photocatalyst, and gaseous reactants. Experimental results showed that the photocatalyst had a high adsorption performance and a good photocatalytic activity for four carbonyl compounds mixture. Some factors influencing the photocatalytic decomposition of the mixed carbonyl compounds, i.e. the gas flowrate, relative humidity, concentration of oxygen, and illumination time, were discussed in detail. It is found that the photocatalytic reaction rate of four carbonyl compounds decreased in this order: propionaldehyde, acetone, acetaldehyde and formaldehyde.     

Fine route for an efficient removal of 2,4-dichlorophenoxyacetic acid (2,4-D) by zeolite-supported TiO2

Zeolites HY, Hbeta and HZSM-5 with different physico-chemical properties were chosen as support for TiO2 to illustrate their adsorption, dispersion and electronic structure in photocatalysis. The extent of TiO2 loading was monitored by XRD and BET surface area measurements. The adsorption capacity of HY zeolite was found to be high and hence chosen for further modification to continue the investigation. Photodegradation kinetics were carried out with 2,4-dichlorophenoxyacetic acid (2,4-D) in aqueous solution. The extent of 2,4-D degradation on TiO2/HY loading revealed the importance of adsorption in photocatalysis. Mineralisation studies on all three zeolites with 1 wt.% TiO2 loading demonstrated the good dispersion properties of TiO2/HY. Its photocatalytic activity was found to be excellent with formulated 2,4-D. Comparison of relative photonic efficiencies demonstrated that supported photocatalysts exhibited higher activity than some of the commercial photocatalysts. The high activity of supported TiO2 is due to synergistic effects of improved adsorption of 2,4-D and efficient delocalisation of photogenerated electrons by zeolite support.     

Photocatalytic activity of TiO2 films grown on different substrates

Titanium dioxide films were prepared on glass, indium-tin oxide (ITO) glass and p-type monocrystalline silicon and studied for the photocatalytic degradation of rhodamine B in an aqueous medium. Raman, AFM, and XPS spectroscopic investigations of these films indicated that microstructure of titanium oxide films were greatly affected by the substrate materials. Rutile was confirmed to be easily formed on the surface of ITO glass, and TiO2 tended to grow as closely packed particles that were elongated strips with an average size of 20 nm, and had lovely contrast with the perfectly round particles grown on p-type monocrystalline silicon. Charge transfer between the film and silicon substrate was verified by surface photovoltage spectra. This may be the real reason why the films grown on ITO glass and silicon substrates exhibit higher photocatalytic reactivity than the film on glass substrate. Moreover, the different surface properties also seem to be responsible for the different activity.     

Comparison of catalytic activity of two platinised TiO2 films towards the oxidation of organic pollutants

Two types of platinised TiO2 films, i.e., Pt-TiO2/ITO and Pt(TiO2)/ITO, were prepared by a procedure of dip-coating and subsequent photo-deposition, and photo-deposition and subsequent dip-coating, respectively. They were well characterized by DRS, XRD spectra, SEM microscopy and photoelectrochemical measurement. Their photocatalytic, dark catalytic and photoelectrocatalytic activities were investigated using formic acid as a model organic pollutants. Compared with pure TiO2/ITO film, the photocatalytic activity of the platinised TiO2 films were apparently improved. However, the improvement was considerably dependent on the preparation method of these films. Pt-TiO2/ITO not only possessed higher photocatalytic activity but also showed a dark catalytic activity towards HCOOH degradation. As a sequence, it was first emphasized that the dark catalytic effect of Pt-TiO2/ITO was partly responsible for degradation of formic acid in the photocatalytic oxidation process. Although the Pt(TiO2)/ITO film does not exhibit the dark catalytic activity, its photocatalytic degradation efficiencies towards HCOOH are higher than that of Pt-TiO2/ITO film. Therefore, in view of enhanced photocatalytic activity, the Pt(TiO2)/ITO was more favored than Pt-TiO2/ITO film.     

SO2-4/TiO2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明:随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温(<550℃)焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时(>550℃)SO42-在TiO2表面是桥式配位吸附。     

碘掺杂Ti02可见光光催化性能研究

在低于100℃温度条件下，采用溶胶一凝胶法以钛酸正丁酯为钛源，碘酸钾为碘源，制备了I掺杂纳米TiO2催化剂（I-TiO2），运用x-射线衍射（XRD）、透射电镜（TEM）及x-射线光电子能谱（XPS）等对催化剂进行表征，结果表明，TiO2及I-TiO2催化剂均为锐钛矿，I吸附并包裹在TiO2表面或以间隙进入的形式存在，并未进入TiO2晶格。通过在可见光照射下（A〉420nm）以罗丹明B（RhodamineB，RhB）的光催化降解为探针反应研究了在不同条件下制备催化剂的催化性能，结果表明，掺杂比为n1：n^ti=0．05：l，焙烧温度为400℃，降解介质条件pH=7时，l-TiO2光催化活性明显优于未掺杂的TiO2。光催化降解过程通过红外光谱（IR），总有机碳（TOC）跟踪测定，比较了TiO2掺杂前后降解RhB和对氯苯酚（4-CP）的光催化特性差异；同时采用苯甲酸荧光光度法跟踪测定体系中的氧化物种，表明在可见光下，I-TiO2光催化体系中产生·OH高活性氧化物种从而氧化降解目标化合物。     

Photocatalytic degradation of the herbicide erioglaucine in the presence of nanosized titanium dioxide: comparison and modeling of reaction kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO2 nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO2 system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir-Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm-1 and 0.984 ppm min-1, respectively. In this work, we also compared the reactivity between the commercial TiO2 Degussa P-25 and a rutile TiO2. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO2 for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO2 process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO2.