CdS-TiO_2/MWCNTs结构表征及其光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管(MWCNTs)负载的双组分复合半导体光催化剂CdS-TiO2/MWCNTs。通过透射电镜(TEM)、比表面分析(BET)、X射线衍射(XRD)和紫外-可见吸收光谱(UV-vis)等分析方法对光催化剂进行了结构表征,并考察了CdS-TiO2/MWCNTs对甲苯降解的光催化性能。结果表明:纳米活性粒子CdS-TiO2均匀负载于MWCNTs上,比表面积、光吸收阈值和强度增大,活性粒子间以及活性粒子与载体之间具有协同作用,有利于光催化性能的提高,CdS-TiO2/MWCNTs在主波长为254 nm紫外光照射下对甲苯的降解效果较好,去除率可达55.3%。     

Fate of citalopram during water treatment with O3, ClO2, UV and Fenton oxidation

In the present study we investigate the fate of citalopram (CIT) at neutral pH using advanced water treatment technologies that include O₃, ClO₂ oxidation, UV irradiation and Fenton oxidation. The ozonation resulted in 80% reduction after 30 min treatment. Oxidation with ClO₂ removed >90% CIT at a dosage of 0.1 mg L⁻¹. During UV irradiation 85% reduction was achieved after 5 min, while Fenton with addition of 14 mg L⁻¹ (Fe²⁺) resulted in 90% reduction of CIT. During these treatment experiments transformation products (TPs) were formed from CIT, where five compounds were identified by using high resolution and tandem mass spectrometry. Among these desmethyl-citalopram and citalopram N-oxide have been previously identified as human metabolites, while three are novel and published here for the first time. The three TPs are a hydroxylated dimethylamino-side chain derivative, a butyrolactone derivative and a defluorinated derivative of CIT.     

Biosafety assessment of titanium dioxide nanoparticles in acutely exposed nematode Caenorhabditis elegans with mutations of genes required for oxidative stress or stress response

We used Caenorhabditis elegans to investigate whether acute exposure to TiO₂-NPs at the concentration of 20 μg L⁻¹ reflecting predicted environmental relevant concentration and 25 mg L⁻¹ reflecting concentration in food can cause toxicity on nematodes with mutations of susceptible genes. Among examined mutants associated with oxidative stress and stress response, we found that genes of sod-2, sod-3, mtl-2, and hsp-16.48 might be susceptible for TiO₂-NPs toxicity. Mutations of these genes altered functions of both possible primary and secondary targeted organs in nematodes exposed to 25 mg L⁻¹ of TiO₂-NPs for 24-h. Mutations of these genes caused similar expression patterns of genes required for oxidative stress in TiO₂-NPs exposed mutant nematodes, implying their similar mechanisms to form the susceptible property. Nevertheless, acute exposure to 20 μg L⁻¹ of TiO₂-NPs for 24-h and 25 mg L⁻¹ of TiO₂-NPs for 0.48-h or 5.71-h did not influence functions of both possible primary and secondary targeted organs in sod-2, sod-3, mtl-2, and hsp-16.48 mutants. Therefore, our results suggest the relatively safe property of acute exposure to TiO₂-NPs with certain durations at predicted environmental relevant concentrations or concentrations comparable to those in food in nematodes with mutations of some susceptible genes.     

Perfluorinated compounds in Haihe River and Dagu Drainage Canal in Tianjin, China

In this study, nine perfluorinated compounds (PFCs) were investigated in water and sediment of Haihe River (HR) and Dagu Drainage Canal (DDC), Tianjin, China. The total PFCs in water samples from DDC (40-174 ng L⁻¹) was much greater than those from HR (12-74 ng L⁻¹). PFC contamination was severe at lower reaches of HR due to industry activities, while high PFCs were found in the middle of DDC due to the effluents from wastewater treatment plants. Perfluorohexanoic acid (PFHxA), perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were the predominant PFCs in aqueous phase. The total PFCs in sediments from DDC (1.6-7.7 ng g⁻¹ dry weight) were lower as compared to HR (7.1-16 ng g⁻¹), maybe due to the dredging of sediment in DDC conducted recently. PFOS was the major PFC in HR sediments followed by PFOA; while PFHxA was the major PFC in DDC sediments. Organic carbon calibrated sediment-water distribution coefficients (K_OC) were calculated for HR. The Log K_OC ranged from 3.3 to 4.4 for C7-C11 perfluorinated carboxylic acids, increasing by 0.1-0.6 log units with each additional CF₂ moiety. The log K_OC for 8:2 fluorotelomer unsaturated acid was reported for the first time with a mean value of 4.0. The log Koc of PFOS was higher than perfluoronanoic acid by 0.8 log units.     

Photocatalytic degradation of gaseous toluene over Ag-doping TiO₂ nanotube powder prepared by anodization coupled with impregnation method

In this work, Ag-doping TiO₂ nanotubes were prepared and employed as the photocatalyst for the degradation of toluene. The TiO₂ nanotube powder was produced by the rapid-breakdown potentiostatic anodization of Ti foil in chloride-containing electrolytes, and then doped with Ag through an incipient wetness impregnation method. The samples were characterized by scanning electron microscope, high-resolution transmission electron microscopy, X-ray diffraction, surface photovoltage measurements, X-ray photoelectron spectroscopy and N₂ adsorption. The nanotubular TiO₂ photocatalysts showed an outer diameter of approximately 40 nm, fine mesoporous structure and high specific surface area. The photocatalytic activity of Ag-doping TiO₂ nanotube powder was evaluated through photooxidation of gaseous toluene. The results indicated that the degradation efficiency of toluene could get 98% after 4 h reaction using the Ag-doping TiO₂ nanotubes as the photocatalyst under UV light illumination, which was higher than that of the pure TiO₂ nanotubes, Ag-doping P25 or P25. Benzaldehyde species could be observed during the photocatalytic oxidation monitored by in situ FTIR, and the formed benzaldehyde intermediate during reaction would be partially oxidized into CO₂ and H₂O.     

Photocatalytic removal of organic pollutants in aqueous solution by Bi(4)Nb(x)Ta((1-x))O(8)I

In this work, Bi₄Nb_xTa_(1−x)O₈I photocatalysts have been synthesized by solid state reaction method and characterized by powder X-ray diffraction, scanning electron microscope and UV-Vis near infrared diffuse reflectance spectroscopy. The photocatalytic activity of these photocatalysts was evaluated by the degradation of methyl orange (MO) in aqueous solutions under visible light, UV light and solar irradiation. The effects of catalyst dosage, initial pH and MO concentration on the removal efficiency were studied, and the photocatalytic reaction kinetics of MO degradation as well. The results indicated that Bi₄Nb_xTa_(1−x)O₈I exhibited high photocatalytic activity for the removal of MO in aqueous solutions. For example, the removal efficiency of MO by Bi₄Nb_0.1Ta_0.9O₈I was as high as 92% within 12 h visible light irradiation under the optimal conditions: initial MO concentration of 5-10 mg L⁻¹, catalyst dosage of 6 g L⁻¹ and natural pH (6-8), the MO molecules could be completely degradated by Bi₄Nb_0.1Ta_0.9O₈I within 40 min under UV light irradiation, and the photodegradation efficiency reaches to 60% after 7 h solar irradiation. Furthermore, the photocatalytic degradation of Bisphenol A (BPA) was also investigated under visible light irradiation. It is found that 99% BPA could be mineralized by Bi₄Nb_0.1Ta_0.9O₈I after 16 h visible light irradiation. Through HPLC/MS, BOD, TOC, UV-Vis measurements, we determined possible degradation products of MO and BPA. The results indicated that MO was degradated into products which are easier to be biodegradable and innocuous treated, and BPA could be mineralized completely. Furthermore, the possibility for the photosensitization effect in the degradation process of MO under visible light irradiation has been excluded.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

Photocatalytic degradation with immobilised TiO(2) of three selected neonicotinoid insecticides: imidacloprid, thiamethoxam and clothianidin

This research focused on photocatalytic degradation of imidacloprid, thiamethoxam and clothianidin employing a tailor-made photoreactor with six polychromatic fluorescent UVA (broad maximum at 355 nm) lamps and immobilised titanium dioxide (TiO₂) on glass slides. The disappearance was followed by high pressure liquid chromatography (HPLC-DAD) analyses, wherein the efficiency of mineralization was monitored by measurements of total organic carbon (TOC). Within 2 h of photocatalysis, all three neonicotinoids were degraded following first order kinetics with rate constants k = 0.035 ± 0.001 min⁻¹ for imidacloprid, k = 0.019 ± 0.001 min⁻¹ for thiamethoxam and k = 0.021 ± 0.000 min⁻¹ for clothianidin. However, the rate of mineralization was low, i.e. 19.1 ± 0.2% for imidacloprid, 14.4 ± 2.9% for thiamethoxam and 14.1 ± 0.4% for clothianidin. This indicates that several transformation products were formed instead. Some of them were observed within HPLC-DAD analyses and structures were proposed according to the liquid chromatography-electro spray ionization tandem mass spectrometry analyses (LC-ESI-MS/MS). The formation of clothianidin, as thiamethoxam transformation product, was reported for the first time.     

Photodegradation of malachite green and malachite green carbinol under irradiation with different wavelength ranges

The dye malachite green (MG) is used worldwide as a fungicide in aquaculture. It is a toxic substance which in aqueous solutions is partly converted into its non-ionic colorless form (leucocarbinol). The equilibrium between these two forms is pH-dependent (pK = 6.9). To assess the photodegradation of MG under sunlight conditions, both species were irradiated separately in aqueous solutions with different pH values (4.0 and 12.0) using various ultraviolet and visible wavelength ranges (UV/VIS). A 700 W high-pressure mercury lamp with special filters was used. No artificial photooxidizers such as H₂O₂ or TiO₂ were added. MG leucocarbinol proved to be much more sensitive to irradiation than the dye form. Quantum yields Φ were calculated for some wavelength ranges as follows: MG carbinol: Φ_(280-312nm) is 4.3 × 10⁻³, Φ_(313-410nm) is 5.8 × 10⁻³, and MG dye: Φ_(280-312nm) is 4.8 × 10⁻⁵, Φ_(313-365nm) is 1.1 × 10⁻⁵, and Φ_(>365nm) is 0, respectively. Therefore, the solar photolysis of MG is an important sink and primarily depends on the photodegradation of the colorless leucocarbinol. During the irradiation of MG leucocarbinol with wavelengths >365 nm, an intermediate was formed which has photocatalytical properties.     

Removal of Rhodamine B under visible irradiation in the presence of Fe⁰, H₂O₂, citrate and aeration at circumneutral pH

A new Vis-Fe⁰-H₂O₂-citrate-O₂ system comprising zero-valent iron, hydrogen peroxide, citrate anion and aeration at circumneutral pH under visible irradiation was studied. 21 μmol L⁻¹ of Rhodamine B (RhB) was chosen as the substrate to be tested. Experiments were conducted under conditions of 2.9 mmol L⁻¹ of H₂O₂, 12.6 g of Fe⁰ and 1.0 mmol L⁻¹ of citrate at pH 7.5. Results showed that, in 1 h reaction, 54% of RhB was removed with corresponding 26% of COD reduced. Meanwhile, the amount of released dissolved irons from Fe⁰ surface was found to be at a very low level as <5.4 μmol L⁻¹. Extinguishing tests with isopropanol suggested that RhB oxidation by hydroxyl radicals was the main process taken place in Vis-Fe⁰-H₂O₂-citrate-O₂ system, which accounted for 75% of substrate removal in 3 h reaction. Control and factor influencing experiments showed that the prohibitive extents of individual factor importance on RhB removal followed a decreasing order of Fe⁰ > H₂O₂ > citrate > Vis > O₂. This study showed an excellent system that could remove refractory organic compounds from water in laboratory researches, and also provided a good idea to reduce secondary contamination by dissolved irons in future investigations.     

Photodegradation of quinestrol in waters and the transformation products by UV irradiation

Quinestrol is synthetic estrogen used in contraceptive and hormone replacement therapy and occasionally for treating breast cancer and prostate cancer. It can make its way into the environment through sewage discharge and waste disposal produced by human excretions. In this study, the photodegradation kinetics of quinestrol in various conditions was investigated by UV and solar irradiation. The affecting factors were studied including concentration of hydrogen peroxide, different water types, and the initial concentrations of quinestrol. Concurrently, the transformation products and presumed pathways of quinestrol in distilled water by UV irradiation were identified and proposed. The results showed that the degradation of quinestrol in both irradiation conditions followed the pseudo-first-order kinetics. More rapid degradation was observed by UV irradiation (k = 0.018 min⁻¹) than solar irradiation (k = 0.004 h⁻¹), and the photodegradation rate of quinestrol depended on the concentration of hydrogen peroxide, the initial concentration of quinestrol and water types. The transformation products of quinestrol in distilled water were identified by gas chromatography/mass spectrometry. When exposed to UV irradiation, quinestrol in aqueous solution was rapidly degraded, giving at least ten photodegradation products. The chemical structures of ten degradation products were identified on the basis of mass spectrum interpretation and literature data.     

Adsorption behavior of perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) on boehmite

Understanding the interaction of perfluorochemicals, persistent pollutants with known human health effects, with mineral compounds in surface water and groundwater environments is essential to determining their fate and transport. Kinetic experiments showed that adsorption equilibrium can be achieved within 48 h and the boehmite (AlOOH) surface is receptive to perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) adsorption. The adsorption isotherms estimated the maximum adsorption capacities of PFOS and PFOA on boehmite as 0.877 μg m⁻² and 0.633 μg m⁻², respectively. Compared to the adsorption capacity on γ-alumina, the abundant hydroxyl groups on boehmite surfaces resulted in the 2-3 times higher adsorption of PFOS and PFOA. Increasing solution pH led to a moderate decrease in PFOS and PFOA adsorption, owing to an increase in ligand exchange reactions and the decrease of electrostatic interactions. The presence of NaCl and CaCl₂ in solution demonstrated negative effects for PFOS and PFOA adsorption on boehmite surfaces, with potential mechanisms being electrical double layer compression, competitive adsorption of chloride, and the Ca²⁺ bridging effect between perfluorochemicals.     

Background levels of Persistent Organic Pollutants in humans from Taiwan: Perfluorooctane sulfonate and perfluorooctanoic acid

Perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) have recently received attention due to their widespread contamination of the environment. PFOS and PFOA are stable in the environment and resistant to metabolism, hydrolysis, photolysis and biodegradation. PFOS and PFOA have been found in human blood and tissue samples from both occupationally exposed workers and the general worldwide population. This study aimed to determine the background levels of PFOS and PFOA in the Taiwanese population, investigate related factors, and compare exposure in Taiwan to that in other countries. The concentration of PFOS in the 59 serum samples collected from the general population in Taiwan ranged from 3.45 to 25.65 ng mL⁻¹ (median: 8.52), and the concentration of PFOA ranged from 1.55 to 7.69 ng mL⁻¹ (median: 3.22). There was a significant positive correlation (r = 0.51; p < 0.0001) between PFOS and PFOA concentrations. Males had higher concentrations of PFOA and PFOS than females. PFOS levels in serum increased with age. This study is the first investigation to reveal the PFOS and PFOA levels of serum samples in the general population of Taiwan. The levels of PFOS and PFOA in Taiwanese serum samples were comparable with those from other countries (PFOS: 5.0–35 ng mL⁻¹, PFOA: 1.5–10 ng mL⁻¹).     

Persistent organic pollutants in sea bass (Dicentrarchus labrax L.) in two fish farms in the Mediterranean Sea

We analyzed polychlorobiphenyls (PCBs), perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) in the edible part of farmed sea bass reared in two fish farms in Liguria (Northern Italy). The aim was to determine the contamination levels and human exposure to these chemicals through fish consumption. Concentrations of “dioxin-like” PCBs (DL-PCBs) ranged from 0.033 to 0.759 pg Σ_TEQ-PCB g⁻¹ whole weight (w.w.) in fish farm 1 and from 0.032 to 1.60 pg Σ_TEQ-PCB g⁻¹ w.w. in fish farm 2, and the six indicators of “non-dioxin-like” (NDL-PCBs) from 0.538 to 9.33 ng Σ_6PCB g⁻¹ w.w. and from 1.62 to 27.6 ng Σ_6PCB g⁻¹ w.w. Concentrations were generally lower in farm 1 than in farm 2. One reason for this difference might be the proximity of farm 2 to the seaport of La Spezia, which could be a punctual source of pollutants influencing the contamination of the water in the farm. Principal component analysis (PCA) showed differences also in the congeners profiles for the two sites, with higher-chlorinated PCBs more abundant in farm 1, and lower-chlorinated PCBs were more abundant in farm 2. Most of the concentrations of PFOS and PFOA were below the limit of detection (LOD 0.05 ng g⁻¹ w.w.). Only about 10% of the samples analyzed had levels slightly higher than the LOD. Assessments of exposure using these data showed that consumption of farmed fish may contribute significantly to PCBs through the diet, whereas the contribution of PFOS and PFOA seems to be low.     

Toxicity of nanoparticulate and bulk ZnO, Al2O3 and TiO2 to the nematode Caenorhabditis elegans

Limited information is available on the environmental behavior and associated potential risk of manufactured oxide nanoparticles (NPs). In this research, toxicity of nanoparticulate and bulk ZnO, Al₂O₃ and TiO₂ were examined to the nematode Caenorhabditis elegans with Escherichia coli as a food source. Parallel experiments with dissolved metal ions from NPs were also conducted. The 24-h median lethal concentration (LC₅₀) and sublethal endpoints were assessed. Both NPs and their bulk counterparts were toxic, inhibiting growth and especially the reproductive capability of the nematode. The 24-h LC₅₀ for ZnO NPs (2.3 mg L⁻¹) and bulk ZnO was not significantly different, but significantly different between Al₂O₃ NPs (82 mg L⁻¹) and bulk Al₂O₃ (153 mg L⁻¹), and between TiO₂ NPs (80 mg L⁻¹) and bulk TiO₂ (136 mg L⁻¹). Oxide solubility influenced the toxicity of ZnO and Al₂O₃ NPs, but nanoparticle-dependent toxicity was indeed observed for the investigated NPs.     

Nitrous oxide and methane emission from a flooded rice field as influenced by separate and combined application of herbicides bensulfuron methyl and pretilachlor

Combination of divergent active principles to achieve broad-spectrum control is gaining popularity to manage the weed menace in intensive agriculture. However, such application could have non-target impacts on the soil processes affecting soil ecology and environmental interactions. A field experiment was conducted to investigate the impact of separate and combined applications of herbicides bensulfuron methyl and pretilachlor on the emission of N₂O and CH₄, and related soil and microbial parameters in a flooded alluvial field planted to rice cv Lalat. Single application of the herbicide bensulfuron methyl or pretilachlor resulted in a significant reduction of N₂O and CH₄ emissions while the combination of these two herbicides distinctly increased N₂O and CH₄ emissions. Cumulative N₂O emissions (kg N₂O-N) followed the order of bensulfuron methyl (0.35 kg ha⁻¹) < pretilachlor (0.36 kg ha⁻¹) < control (0.45 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (0.49 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (0.54 kg ha⁻¹). Cumulative CH₄ emissions (kg CH₄), on the other hand, followed the order of bensulfuron methyl (47.89 kg ha⁻¹) < pretilachlor (73.17 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (93.50 kg ha⁻¹) < control (106.54 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (124.67 kg ha⁻¹). The inhibitory effect of separate application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% on N₂O emission was linked to lower mineral N, lower denitrifying and nitrifying activity and low denitrifier and nitrifier populations. Inhibitory effect on CH₄ emission, on the contrary, was linked to prevention in the drop of redox potential, lower readily mineralizable carbon (RMC) and microbial biomass carbon (MBC) contents as well as lower methanogenic and higher methanotrophic bacterial population. Admittedly, stimulatory effect of combined application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% at double dose on N₂O and CH₄ emission was related to reversal of the identified indicators of inhibition. Results indicate that while individual application of herbicides bensulfuron methyl 0.6% or pretilachlor 6.0% can reduce N₂O and CH₄ emission from flooded soil planted to rice, their combined application at normal dose can keep the emission at a comparatively lower level with significantly higher grain yield as compared to the herbicides applied alone.     

Partitioning of perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS) and perfluorooctane sulfonamide (PFOSA) between water and sediment

Laboratory partitioning experiments were conducted to elucidate the sorption behaviour and partitioning of perfluoroalkyl compounds (PFCs). Three different sediment types were used and separately spiked with perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS) and perfluorooctane sulfonamide (PFOSA) at low environmentally realistic concentrations. PFOA, PFOS and PFOSA were mainly distributed in the dissolved phase at low suspended solid concentrations, indicating their long-range transport potential in the marine environment. In all cases, the equilibrium isotherms were linear and the organic carbon normalised partition coefficients (K_OC) decreased in the following order: PFOSA (log K_OC = 4.1 ± 0.35 cm³ g⁻¹) > PFOS (3.7 ± 0.56 cm³ g⁻¹) > PFOA (2.4 ± 0.12 cm³ g⁻¹). The level of organic content had a significant influence on the partitioning. For the sediment with negligible organic content the density of the sediment became the most important factor influencing the partitioning. Ultimately, data on the partitioning of PFCs between aqueous media and suspended solids are essential for modelling their transport and environmental fate.     

Nano-TiO2 enhances the toxicity of copper in natural water to Daphnia magna

The acute toxicity of engineered nanoparticles (NPs) in aquatic environments at high concentrations has been well-established. This study demonstrates that, at a concentration generally considered to be safe in the environment, nano-TiO₂ remarkably enhanced the toxicity of copper to Daphnia magna by increasing the copper bioaccumulation. Specifically, at 2 mg L⁻¹ nano-TiO₂, the (LC₅₀) of Cu²⁺ concentration observed to kill half the population, decreased from 111 μg L⁻¹ to 42 μg L⁻¹. Correspondingly, the level of metallothionein decreased from 135 μg g⁻¹ wet weight to 99 μg g⁻¹ wet weight at a Cu²⁺ level of 100 μg L⁻¹. The copper was found to be adsorbed onto the nano-TiO₂, and ingested and accumulated in the animals, thereby causing toxic injury. The nano-TiO₂ may compete for free copper ions with sulfhydryl groups, causing the inhibition of the detoxification by metallothioneins.