柠檬酸废水处理改造工程实例

采用多级内循环厌氧反应器MIC/上升式厌氧反应器UASB串联工艺处理柠檬酸生产排放的高浓度有机废水,其中厌氧处理段的COD去除率＞94％,整体COD去除率可达98.3％左右.最终排放口出水COD平均值为190 mg/L,pH值为6～9,达到柠檬酸行业废水排放标准.     

厌氧/好氧组合工艺处理PTA生产废水

采用新研制的上旋流厌氧反应器/两级好氧组合工艺处理PTA废水,调试运行效果表明,当原水CODCr浓度在8000~14,000mg/L时,处理后出水CODCr在80~100mg/L。调试期间,上旋流厌氧反应器的处理效率可稳定达到80%以上。     

多项膜生物反应器在含盐废水处理中的应用

文章介绍了哈尔滨石化公司应用多项膜生物反应器处理炼化企业含盐废水。影响膜生物反应器的主要运行参数有电导率、溶解氧、COD,电导率适宜范围是3000～5000μS/cm,大于6000μS/cm微生物受到抑制,低于2000μS/cm时,去除率显著下降;一级好氧单元溶解氧适宜范围4.2～7.0mg/L或2.0～3.0mg/L,分别是好氧微生物和兼性微生物占据优势;当进水COD低于500mg/L,出水可稳定达到GB8978-1996《污水综合排放标准》二级标准(COD≤120mg/L)。     

玉米酒精废水的处理工艺与设计

针对酒精废水的COD高、温度高、SS高、pH低特点,主要介绍了酒精废水处理工艺路线和主要设计参数。采用高效MIC厌氧反应器和卡鲁塞尔氧化沟3000型,MIC有机负荷可达15kg CODCr/m3.d,CODCr去除率为85%以上,卡鲁塞尔氧化沟有机负荷为0.6kg CODCr/m3.d,CODCr去除率为93%以上,出水COD<150mg/L。厌氧所产生的沼气的回收价值抵去整个系统运行费用,每年可盈余1 300余万元。     

复合式厌氧反应器处理生活污水运行特性研究

本文对复合式折流板厌氧反应器处理生活污水的运行特性进行了研究,并作了灵敏度分析。结果表明:HABR反应器因其特殊的结构而具有很好的耐冲击负荷能力及很好的去除效果;当进水的CODCr在300mg/L左右,温度在16 3～30 5℃时,水力停留时间采用6h,容积负荷为1 2kgCOD/m3·d左右,COD去除率可保持在70%以上,出水CODCr可小于100mg/L,出水SS浓度在27～64mg/L之间;各操作参数对HABR反应器CODCr去除率的影响有显著性不同;HRT是系统运行过程中需严格控制的关键因素。     

水解酸化-两级接触氧化工艺在啤酒废水处理中的应用

啤酒废水具有有机物含量高、悬浮物浓度高、温度高、 pH 值变化大及可生化性较好等特点,生化处理成为国内外啤酒废水处理的主要工艺。公司采用“水解酸化-两级生物接触氧化”工艺对啤酒废水进行处理,运行结果表明,废水pH在8～9, SS、 CODCr、 NH3-N平均浓度分别为710 mg/L、1910 mg/L、49 mg/L时,处理后出水pH在6.5～8.5, SS、 CODCr、NH3-N平均浓度分别为52 mg/L、70 mg/L、11 mg/L, SS、 CODCr、 NH3-N平均去除率分别为93％、96％、77％,满足啤酒废水排放标准的要求。该工艺对废水具有较好的适应性。     

SBR中好氧颗粒污泥的培养

采用竖式SBR作为反应器,利用城市污水处理厂剩余污泥作为接种污泥,通过不间断运行培养出好氧颗粒污泥。实验结果表明,采用非限量曝气模式好氧颗粒污泥降解模拟污水的效果较好,其COD去除率可达98％以上。曝气量对好氧颗粒污泥的形成和稳定具有重要影响,当气速为26．5m／h时,好氧颗粒污泥的性状和处理有机废水效果最佳。同时好氧颗粒污泥对pH值的变化不明显,当pH为5—8范围内,其COD去除率都可达到85％以上。但是未经驯化的好氧颗粒污泥对对硝基苯酚和对氯苯酚两种芳香类有机物较敏感,而对硝基苯酚对其毒性更大。当对硝基苯酚和。对氯苯酚浓度为10mg／L时,其COD去除率仅为42．5％和52％。     

厌氧水解—高负荷生物滤池处理城镇污水的试验研究

厌氧水解－高负荷生物滤池是一种利用附着在塑料模块填料上的微生物系统对城镇污水中的污染物质进行降解处理的绿色环保技术。厌氧水解池和高负荷生物滤池采用的塑料模块填料具有高空隙率、高附着面积、高布水性能和抗堵塞的优异性能,并无须回流。当厌氧水解池水力停留时间为4小时,生物滤池水力负荷为30米^3/米^2。日,该系统处理城镇污水的CODCr去除率达80－86％,BOD5去除率达85％－95％。SS去除率达85－95％,处理后出水上述各项指标均可满足国家二级生物处理排放标准的要求。与广泛运用的活性法处理系统相比,该技术可节约基建投资20％以上,节约能耗50％以上,同时还具有流程简单、管理方便、耐冲击负荷、剩余污泥少等特点。     

混凝沉降-微电解-催化氧化法处理钻井废水

采用混凝沉降-微电解-催化氧化法对钻井废水进行处理,筛选出最佳的工艺条件。实验结果表明,该法可使原水的CODCr从5846 mg/L降至150 mg/L以下,色度去除率达到100%,出水达到排放标准。混凝沉降-微电解-催化氧化法对于处理高CODCr、高色度钻井废水是行之有效的,具有广阔的应用前景。     

催化铁应用于草甘膦废水处理工艺改造的可行性研究

针对某化工厂草甘膦废水经厌氧-好氧生物处理后出水总磷浓度高,无法达到该化工区污水纳管标准的情况,应用催化铁方法对该废水现有处理工艺进行改造以提高出水水质。考察了催化铁方法对原处理工艺不同处理工段出水中磷的去除效果,发现该法可有效地去除生物厌氧池出水的总磷及正磷盐,去除率分别达到52．7％和83．13％以上,且使废水的BOD5／COD值显著提高,可从0．08提高至0．31,增强了废水的可生物降解性,有利于后续好氧生物处理的进行。研究表明在原处理工艺的厌氧池后增加催化铁处理段能明显提高最终出水水质。     

Treatment of low-strength soluble wastewater using an anaerobic baffled reactor (ABR)

Treatment of low-strength soluble wastewater (COD approximately 500 mg/L) was studied using an eight chambered anaerobic baffled reactor (ABR). At pseudo steady-state (PSS), the average total and soluble COD values (COD(T) and COD(S)) at 8h hydraulic retention time (HRT) were found to be around 50 and 40 mg/L, respectively, while at 10h HRT average COD(T) and COD(S) values were of the order of 47 and 37 mg/L, respectively. COD and BOD (3 day, 27 degrees C) removal averaged more than 90%. Effluent conformed to Indian standards laid down for BOD (less than 30 mg/L). Reactor effluent characteristics exhibited very low values of standard deviation indicating excellent reactor stability at PSS in terms of effluent characteristics. Based on mass balance calculations, more than 60% of raw wastewater COD was estimated to be recovered as CH(4) in the gas phase. Compartment-wise profiles indicated that most of the BOD and COD got reduced in the initial compartments only. Sudden drop in pH (7.8-6.7) and formation of volatile fatty acids (VFA) (53-85 mg/L) were observed in the first compartment due to acidogenesis and acetogenesis. The pH increased and VFA concentration decreased longitudinally down the reactor. Residence time distribution (RTD) studies revealed that the flow pattern in the ABR was neither completely plug-flow nor perfectly mixed. Observations from scanning electron micrographs (SEM) suggest that distinct phase separation takes place in an ABR.     

序批式生物膜法处理油田采油废水

采用序批式生物膜(SBBR)法处理油田采油废水。研究并开发了特殊活性污泥的培养和驯化方法。在被处理的污水中加入微生物促生剂FYS-5,可迅速培养出处理采油废水的微生物,用此种方法培养出的活性污泥的活性高,去除有毒有害物质的能力强,能够提高处理效率,保持良好的微生物生长状况。在SBBR装置进水COD容积负荷为0.5kg/(m3·d)及进水COD为500mg/L左右的条件下,经过近两个月的连续运转,COD平均去除率超过80%,出水中COD低于100mg/L,符合GB8978-1996《污水综合排放标准》的要求,经过处理的污水可以直接排放。     

Combined chemical and biological oxidation of penicillin formulation effluent

Antibiotic formulation effluent is well known for its important contribution to environmental pollution due to its fluctuating and recalcitrant nature. In the present study, the chemical treatability of penicillin formulation effluent (average filtered COD(o)=830 mg/l; average soluble COD(o)=615 mg/l; pH(o)=6.9) bearing the active substances penicillin Amoxicillin Trihydrate (C(16)H(19)N(3)O(5)S.3H(2)O) and the beta-lactamase inhibitor Potassium Clavulanate (C(8)H(8)KNO(5)) has been investigated. For this purpose, the penicillin formulation effluent was subjected to ozonation (applied ozone dose=2500 mg/(lxh)) at varying pH (2.5-12.0) and O(3)+H(2)O(2) (perozonation) at different initial H(2)O(2) concentrations (=2-40 mM) and pH 10.5. According to the experimental results, the overall Chemical Oxygen Demand (COD) removal efficiency varied between 10 and 56% for ozonation and 30% (no H(2)O(2)) and 83% (20 mM H(2)O(2)) for the O(3)+H(2)O(2) process. The addition of H(2)O(2) improved the COD removal rates considerably even at the lowest studied H(2)O(2) concentration. An optimum H(2)O(2) concentration of 20 mM existed at which the highest COD removal efficiency and abatement kinetics were obtained. The ozone absorption rate ranged between 53% (ozonation) and 68% (perozonation). An ozone input of 800 mg/l in 20 min was sufficient to achieve the highest BOD(5)/COD (biodegradability) ratio (=0.45) and BOD(5) value (109 mg/l) for the pre-treated penicillin formulation effluent. After the establishment of optimum ozonation and perozonation conditions, mixtures of synthetic domestic wastewater+raw, ozonated and perozonated penicillin formulation effluent were subjected to biological activated sludge treatment at a food-to-microorganisms (F/M) ratio of 0.23 mg COD/(mg MLSSxd), using a consortium of acclimated microorganisms. COD removal efficiencies of the activated sludge process were 71, 81 and 72% for pharmaceutical wastewater containing synthetic domestic wastewater mixed with either raw, ozonated or perozonated formulation effluent, respectively. The ultimate COD value obtained after 24-h biotreatment of the synthetic domestic wastewater+pre-ozonated formulation effluent mixture was around 100 mg/l instead of 180 mg/l which was the final COD obtained for the wastewater mixture containing raw formulation effluent, indicating that pre-ozonation at least partially removed the non-biodegradable COD fraction of the formulation effluent.     

Biological treatment of anaerobically digested palm oil mill effluent (POME) using a Lab-Scale Sequencing Batch Reactor (SBR)

The production of highly polluting palm oil mill effluent (POME) has resulted in serious environmental hazards. While anaerobic digestion is widely accepted as an effective method for the treatment of POME, anaerobic treatment of POME alone has difficulty meeting discharge limits due to the high organic strength of POME. Hence, subsequent post-treatment following aerobic treatment is vital to meet the discharge limits. The objective of the present study is to investigate the aerobic treatment of anaerobically digested POME by using a sequencing batch reactor (SBR). The SBR performance was assessed by measuring Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD) and Total Suspended Solids (TSS) removal as well as Sludge Volume Index (SVI). The operating pH and dissolved oxygen concentrations were found to be 8.25–9.14 and 1.5–6.4 mg/L, respectively, throughout the experiment. The experimental results demonstrate that MLVSS, OLR and sludge loading rate (SLR) play a significant role in the organic removal efficiency of SBR systems and therefore, further investigation on these parameters was conducted to attain optimum SBR performance. Maximum COD (95–96%), BOD (97–98%) and TSS (98–99%) removal efficiencies were achieved at optimum OLR, SLR and MLVSS concentration ranges of 1.8–4.2 kg COD/m³ day, 2.5–4.6 kg TSS/m³ day and 22,000–25,000 mg/L, respectively. The effluent quality remained stable and complied with the discharge limit. At the same time, the sludge showed good settling properties with average SVI of 65. It is envisaged that the SBR process could complement the anaerobic treatment to produce final treated effluent which meets the discharge limit.     

A pilot plant using immobilized cells for dye removal from dye manufacturing wastes

A pilot plant was set up to treat dye waste water. The flow of the plant begins with a chemical pretreatment step following by an immobilized decolorizing bacteria reactor and an ordinary activated sludge reactor at the end. Results from the seven months' operation show that the decolorization effect of the immobilized cell reactor worked satisfactorily. The effluent colour always remained below 100 with the influent colour as high as 4000 or more. The COD of the effluent could also meet the discharge standard, around 60 mg L⁻¹. The immobilized cell reactor has an ability to reduce the BOD/COD ratio of the waste, suggesting that it can degrade the recalcitrant pollutants easily. The results show that it is a high-efficiency and low-cost process suitable to be developed into full-scale application.     

活性污泥法+接触氧化法工艺处理高盐度环氧丙烷生产废水的试验研究

采用活性污泥法和接触氧化两段工艺对高含盐的环氧丙烷生产废水进行处理，同时研究了不同水力停留时间的处理效果和不同的盐度对处理效果的影响。试验结果表明CODcr的去除率可以达84．38％，出水CODcr＜160mg／L，pH＜8。     

Use of constructed wetland systems with Arundo and Sarcocornia for polishing high salinity tannery wastewater

Treatment of tannery wastewater is problematic due to high and variable concentrations of complex pollutants often combined with high salinity levels. Two series of horizontal subsurface flow constructed wetlands (CWs) planted with Arundo donax and Sarcocornia fruticosa were set up after a conventional biological treatment system operating at a tannery site. The aim of the CWs was polishing organics and nitrogen from the high salinity effluent (2.2-6.6?g Cl(-)?L(-1)). Both plant species established and grew well in the CW. Arundo, however, had more vigorous growth and a higher capacity to take up nutrients. The CWs were efficient in removing COD and BOD(5) with removal efficiencies varying between 51 and 80% for COD (inlet: 68-425?mg?L(-1)) and between 53 and 90% for BOD(5) (inlet: 16-220?mg?L(-1)). Mass removal rates were up to 615?kg COD ha(-1)?d(-1) and 363 BOD(5) kg?ha(-1)?d(-1). Removal efficiencies were 40-93% for total P, 31-89% for NH(4)(+) and 41-90% for Total Kjeldahl Nitrogen. CW systems planted with salt tolerant plant species are a promising solution for polishing saline secondary effluent from the tannery industry to levels fulfilling the discharge standards.     

混凝—催化臭氧化处理垃圾渗滤液MBR出水

本文研究了混凝—催化臭氧化对垃圾渗滤液MBR出水COD、UV254和色度的去除效果及可生化性能的影响。在pH 11,FeCl3用量800 mg/L的优化条件下,COD、UV254和色度去除率分别为37.8%、61.9%和88.7%。混凝出水催化臭氧化结果表明,3%-Ce/AC催化臭氧化效率最好,COD去除率为33.6%,臭氧消耗系数为1.40 mgO3/mgCOD。经混凝—催化臭氧化处理后,MBR出水的COD、UV254及色度总去除率分别为58.7%、90.8%及98.7%,BOD5/COD从0.036提高到0.375,可生化性明显改善。