Methane/coal dust/air explosions and their suppression by solid particle suppressing agents in a large-scale experimental tube

Methane/coal dust/air explosions under strong ignition conditions have been studied in a 199 mm inner diameter and 30.8 m long horizontal tube. A fuel gas/air manifold assembly was used to introduce methane and air into the experimental tube, and an array of 44 equally spaced dust dispersion units was used to disperse coal dust particles into the tube. The methane/coal dust/air mixture was ignited by a 7 m long epoxypropane mist cloud explosion. A deflagration-to-detonation transition (DDT) was observed, and a self-sustained detonation wave characterized by the existence of a transverse wave was propagated in the methane/coal dust/air mixtures.The suppressing effects on methane/coal dust/air mixture explosions of three solid particle suppressing agents have been studied. Coal dust and the suppressing agent were injected into the experimental tube by the dust dispersion units. The length of the suppression was 14 m. The suppression agents examined in this study comprised ABC powder, SiO₂ powder, and rock dust powder (CaCO₃). Methane/coal dust/air explosions can be efficiently suppressed by the suppression agents characterized by the rapid decrease in overpressure and propagating velocity of the explosion waves.     

Study of dust cloud behaviour in the modified Hartmann tube using the image subtraction method (ISM)

A dispersion of fine particles in the air is needed for a dust explosion to occur since an explosion is the fast combustion of particles in the air. When particles are poorly dispersed, agglomerated, or their concentration is low, the combustion velocity decreases, and deflagration would not occur. The combustion rate is strictly related to dust concentration. Therefore, the maximum explosion pressure rise occurs at dust concentration close to stoichiometric. Conversely, Minimum Explosion Concentration (MEC) is the lower limit at which self-sustained combustion and a pressure rise are possible. Dust explosion tests are designed to reproduce the dispersion and generation of dust clouds in industrial ambiences by using dispersion devices activated by pressurised air pulses. The resulting dust cloud, which has a marked transient character, is considered representative of real clouds by current standards. Over time, several studies have been carried out to optimise these devices (e.g. to reduce the inhomogeneity of the cloud in the 20 L sphere). The Minimum Ignition Energy (MIE) of dust is measured using the Mike3 modified Hartmann tube, where the ignition attempt is made 60–180 ms after dust dispersion regardless of dust characteristics.This work investigates the dust clouds’ actual behaviour inside the modified Hartmann tube before ignition using high-velocity video movies and a new image post-treatment method called Image Subtraction Method (ISM). Movies are recorded with high-speed cameras at a framerate of 2000 fps and elaborated with an on-purpose developed LabVIEW® code. Concentration (mass per volume) and dispersion pressure are varied to evaluate their effect on dust clouds. Maise starch, iron powder and silica powder are chosen to investigate the effect of particle density and size on the cloud structure and turbulence. This approach will help to investigate the structure of the dust cloud, the shape and size of the particle lumps and the change in dust concentration over time. In addition, information on the actual concentration and cloud turbulence at the ignition location and delay time were obtained, which may help identify the local turbulence scale and widen the characterisation of the cloud generated in the Hartmann tube.     

Experimental investigation and modelling of aluminum dusts explosions in the 20 L sphere

An experimental investigation was carried out on the influences of dust concentration, particle size distribution and humidity on aluminum dust explosion. Tests were mainly conducted thanks to a 20 L explosion sphere. The effect of humidity was studied by storing the aluminum particles at constant relative humidity until the sorption equilibrium or by introducing water vapour in the explosion vessel. The tested particles sizes ranged from a volume median diameter of 7 to 42 μm and the dust concentrations were up to 3000 g m^?3.Among other results, the strong influence of the particle size was pointed out, especially when the Sauter mean diameter is considered. These results stressed the predominance of the specific surface area on the mass median particle diameter.The effect of water on aluminum dust explosion was decoupled: on the one hand, when water adsorption occurs, hydrogen generation leads to an increase of the explosion severity; on the other hand, when the explosion of dried aluminum powder occurs in a humid atmosphere, the inhibiting effect of humidity is put forward.A model based on mass and heat balances, assuming a shrinking core model with chemical reaction limitation, leads to a satisfactory representation of the pressure evolution during the dust explosion.     

彩虹粉引燃危险性实验研究

为了研究彩虹粉引燃危险性,应用固体燃烧速率试验仪初步甄别了彩虹粉传播燃烧能力,发现堆垛状彩虹粉固体火焰传播危险性较低;采用粉尘爆炸筛选装置,判定彩虹粉具有爆炸性;应用最小点火能测定装置测定彩虹粉粉尘云的最小点火能在24~60 mJ之间,最优爆炸浓度为1 167 g/m3;应用快速筛选量热仪测试,彩虹粉在227℃开始分解;固体自燃点测试仪显示彩虹粉在250℃附近会发生自燃。向彩虹粉内添加不同比例相近粒径分布的食用盐粉体进行抑爆研究,结果证明食用盐对彩虹粉具有明显的抑爆效果。     

多孔球形材料阻火抑爆性能影响因素数值模拟研究

为探究影响多孔球形材料阻火抑爆性能的主要因素,采用气体爆炸模拟软件FLACS建立多孔球形结构中湍流燃烧模型,对填充多孔球形材料后丙烷/空气预混气体燃烧爆炸过程进行数值模拟。研究结果表明:多孔球形材料能够有效衰减爆燃压力波、阻隔火焰传播,起到阻火抑爆作用,且压力波衰减程度和火焰阻隔效果与多孔球形材料的尺寸、孔径及填充密度密切相关。当多孔球形材料的直径为25 mm、孔径为3 mm、填充密度为20层时,压力波衰减程度最大,火焰阻隔效果最明显,说明直径和孔径越小,填充密度越大,材料的阻火抑爆性能越强。     

混合药物粉尘输运过程静电特性实验研

兽药制药粉尘加工工艺过程中,由于粉尘颗粒之间或颗粒与设备、管壁之间的碰撞、摩擦,导致装置内部静电荷量积聚,激发静电放电,粉尘燃烧或爆炸的事故频发。实验主要通过包括粉尘与管材摩擦的漏电电流测试和静电放电火花对粉尘云点燃敏感性测试两部分。结果表明:单一药物药粉的静电漏电电流随着管材管径的增大,管长的增长,静电漏电电流逐渐变大;随着倾斜角的增大,静电漏电电流先增大后降低;镀锌铁管的漏电电流大于PVC管,电荷逸散速度更快。单一兽药粉的粉尘云放电火花最小点燃能量随质量浓度的变化,呈现二次曲线的变化趋势。混合兽药粉与单一兽药粉的漏电电流和粉尘云放电火花最小点燃能量的测试结果的变化趋势是一致的。     

激波诱导下煤粉的爆炸压力测试

因气体爆炸导致沉积粉尘的二次爆炸的威力远大于单纯的气体或者粉尘爆炸产生的威力,利用自制的装置,诱导煤粉爆炸的激波由甲烷气体爆炸产生,对激波诱导下煤粉的爆炸压力Pmax、爆炸压力上升速率(dp/dt)max进行了实验研究。该实验分别研究煤粉浓度及煤粉粒度对爆炸指数的影响,其结果表明:对于不同的煤粉浓度,存在一个理想煤粉浓度值,在这个浓度下的煤粉爆炸压力值最大;随着煤粉粒度的减小,其爆炸压力不断升高。     

The effect of admixed material on the minimum explosible concentration of oil shale

The minimum explosible concentration (MEC) in the air atmosphere at the boundary between an explosion and no explosion in a dust cloud, has been investigated for several particle sizes of oil shale and for mixtures of oil shale and inert powder of different particle size. Limestone, stone dust and coarse particle size of oil shale were used as inert materials. Measurements were made in a standard small vertical tube apparatus. The results obtained indicated that the minimum explosible concentration is dependent on the particle size, i.e., values of MEC decrease with a decrease in the size of the particles. Below 70 μm, values of MEC become almost constant. Admixture of limestone as low as 5% to oil shale is sufficient to reduce the MEC values significantly.     

超细CaCO3惰化剂对铝合金抛光伴生粉尘爆炸的防控效果*

为探究超细粉体惰化剂对铝合金抛光伴生粉尘爆炸特性的影响规律,利用标准化实验装置及自行搭建的实验平台,在对爆炸基本参数进行测试的基础上,分别研究超细CaCO3粉体对抛光废弃物粉尘点燃敏感度的钝化作用以及对爆炸火焰传播进程的惰化效果,并在相同条件下与同等粒径高纯度铝粉的实验效果进行比对。研究结果表明:铝合金抛光废弃物粉尘最小点火能量为280 mJ,而同等粒径高纯度铝粉最小点火能量为35 mJ;在铝合金抛光废弃物粉尘质量浓度为300 g/m3条件下,发生爆炸的火焰传播速度峰值为7.4 m/s,约为高纯度铝粉的57%,铝合金抛光废弃物粉尘的爆炸敏感度及猛烈度均低于高纯度铝粉;当超细CaCO3粉体的惰化比为30%时,可将铝合金抛光废弃物粉尘的最小点火能量钝化至约1 J,爆炸火焰失去持续传播能力,惰化作用效果充分显现。     

混合金属粉尘爆炸最小点火能量影响因素研究*

为探究混合金属粉尘爆炸危险性及与单一粉体爆炸特性差异，确保车间安全生产，采用粉尘云点火能量测试系统对车间混合金属粉尘及铝粉最小点火能量在不同影响因素下的变化规律及2种粉尘火焰变化特征进行测试。研究结果表明:混合金属粉尘和铝粉最小点火能量在一定范围内（38~96 μm）与粒径呈正相关性，当混合金属粉尘粒径大于75 μm时，所需最小点火能量大于1 000 mJ，其爆炸敏感性迅速降低，此时铝粉仍有较强爆炸敏感性；2种粉尘最小点火能量随质量浓度增加呈先降低后升高的趋势，最小点火能分别为295，15 mJ，对应的敏感质量浓度为600，1 000 g/m3，混合金属粉尘在质量浓度为500~700 g/m3时具有较大爆炸危险性；同铝粉相比，混合金属粉尘点火能量更高、火焰燃烧时间更短、火焰高度更低、爆炸剧烈程度更弱。     

Structure of flames propagating through aluminum particles cloud and combustion process of particles

Structure of flames propagating through aluminum particles clouds and combustion processes of the particles have been examined experimentally to understand the fundamental behavior of a metal dust explosion. The combustion process of individual aluminum particles in a flame propagating through the aluminum particles cloud has been recorded by using a high-speed video camera with a microscopic optical system, and analyzed. The flame is shown to be consisted of a preheat zone of about 3 mm thick, followed by a combustion zone of 5–7 mm thick. In the combustion zone, discrete gas phase flames are observed around each aluminum particle. Also an asymmetric flame around a particle is observed, which might be caused by an ejection of aluminum vapor from a crack of oxide shell surrounding the particle.     

抛光铝粉爆炸及ABC粉体抑爆特性的实验研究

为研究抛光铝粉的爆炸危险和ABC粉体的抑爆特性，在对实验粉体粒径分布进行分析的基础上，采用20 L粉尘爆炸特性实验装置，分别对不同铝粉尘浓度、不同抑爆剂浓度条件下的爆炸特性参数进行测试。研究结果表明:在实验条件下，铝粉的爆炸下限为45 g/m3＜C＜60 g/m3；随铝粉浓度增加，爆炸烈度呈现出先增强后减弱的变化趋势，在浓度为400 g/m3时爆炸烈度最大。ABC抑爆剂能够有效抑制铝粉爆炸超压和爆炸反应进程，随着惰性粉体浓度的增加，抑制效果愈加明显，爆炸逐渐减弱。当ABC惰性粉体的质量占比增加到50%时，相较单一铝粉爆炸，反应过程时间由72 ms增加至785 ms，爆炸最大压力、最大压力上升速率分别下降了61.7%，89.5%；当ABC粉体质量占比为53%时，铝粉被完全惰化，未发生爆炸。     

基于20 L球罐的多相混合物扩散模拟

为更好地探索多相混合物的爆炸特性，以铝粉、乙醚、空气为研究对象，基于20 L球型爆炸罐建立三维计算模型，对气固两相和气液固三相混合物的分散过程进行数值模拟，以分析不同多相混合物分散过程的差异，并为测量多相混合物爆炸下限时的点火延迟时间设定提供参考。监测分析铝粉浓度粒子分布、流场内部湍流动能以及液相体积百分数等的演化过程，讨论混合物分散效果的差异，并确定测量爆炸下限的点火延迟时间。研究结果表明:实验工况下，液相的存在会降低粉尘云团的湍流动能、降低其扩散速度，并使粉尘云内部浓度更均匀。测量多相混合物爆炸下限时，三相混合物的最佳点火延迟时间早于气固两相混合物10~20 ms。     

CO2-超细水雾对瓦斯/煤尘爆炸抑制特性研究

为了解CO2-超细水雾对瓦斯/煤尘爆炸抑制特性，用自行搭建的实验系统，从超压、火焰传播速度和火焰结构3个方面研究了CO2-超细水雾形成的气液两相介质对9.5%瓦斯/煤尘复合体系爆炸的抑爆效果、影响因素与原因。研究结果表明:随着CO2体积分数和超细水雾质量浓度的增加，爆炸火焰最大传播速度、爆炸超压峰值均出现明显下降，火焰到达泄爆口时间显著延迟；尤其当CO2体积分数达到14%与超细水雾的共同抑爆效果凸显，瓦斯/煤尘复合体系爆炸超压的“震荡平台”消失，同时火焰结构呈现“整体孔隙化”。所得结论为煤矿井下高效防爆抑爆技术进行了完善和增强。     

网状铝合金抑爆材料抑爆性能研究

为评价网状铝合金材料的阻隔防爆性能,基于多孔材料的阻隔防爆机理,采用抑爆材料抑爆性能测试装置和可燃气体爆炸箱及高速摄像机,研究材料在不同填充密度、不同留空率下对液化石油气的燃爆压力的影响,及液化石油气火焰在填充材料的爆炸箱中的传播过程。试验结果表明:填充密度为35 kg/m3、留空率为5%时,材料抑爆性能最好;当抑爆材料在容器内的填充密度一定时,其燃爆压力随留空率增加而增加;与未填充材料相比,填充材料后火焰衰减;此外,得到填充密度、留空率和燃爆压力间的数学拟合公式。降低留空率、增加填充密度能够更好地提高阻隔防爆性能。     

超细聚苯乙烯微球粉体的燃爆特性研究

为研究超细聚苯乙烯微球粉体的燃爆特性,通过粉尘层最低着火温度测试装置、MIE-D1.2最小点火能测试装置、20 L球形爆炸测试装置,对其最低着火温度、最大爆炸压力、最小点火能量(MIE)等爆炸特性参数进行测定,探讨了加热温度、点火延滞时间、粉尘质量浓度、粉尘粒径对粉体燃爆特性的影响。结果表明:超细聚苯乙烯微球粉尘层在350℃左右时会发生无焰燃烧,且加热温度越高,粉体粒径越小,粉尘层发生着火时所需的时间越短;当粉体质量浓度为250 g/m3时,最大爆炸压力达到0.65 MPa,质量浓度为500 g/m3时,最大爆炸压力的上升速率达90 MPa/s以上;随点火延滞时间增加,最小点火能表现出先缓慢减小再急剧增大的规律;随粉尘质量浓度增加,最小点火能逐渐降低,当粉尘质量浓度超过500g/m3后逐渐趋于稳定。     

Suppression effects of ammonium dihydrogen phosphate dry powder and melamine pyrophosphate powder on an aluminium dust cloud explosion

Selecting a suitable flame-retardant powder is essential for preventing or reducing the risk of aluminium dust cloud explosions. Two types of retardant materials were studied, namely ABC powder (a flame-retardant powder mainly composed of ammonium dihydrogen phosphate dry powder) and melamine pyrophosphate powder (MPP). A specially designed rectangular pipe was used to examine the influences and mass fractions of the aforementioned flame retardants and the effects of compounds on maximum explosion pressure and maximum explosion pressure rate of increase. The results showed that the explosion-suppression effects of MPP powder were superior to those of ABC powder. Furthermore, the suppression effects of combining ABC and MPP to form compounds in various ratios were explored. The explosion-suppression effects of the single flame-retardant powders and flame-retardant powder compound were compared, which revealed that the effects of the flame-retardant compound were intermediate to those of ABC and MPP used separately. No synergistic effect was observed in the compound retardant. However, component mass fractions influenced the retardant properties of the compound. The suppression mechanism was investigated through thermal analysis, which revealed that the decomposition of the two flame-retardant powders was an endothermic process that generated inert gas. The addition of flame-retardant powder delayed the time required by aluminium to break through its oxide film. However, the thermal analysis curve of the compound overlapped those of the two single powders, and no new chemical reaction occurred. Thus, no change was observed in the efficacy of the flame-retardant properties.     

外部条件对玉米淀粉粉尘爆炸特性的影响

为了探明外部条件对玉米淀粉粉尘爆炸特性参数的影响,利用20 L球形爆炸装置进行试验测试,探讨了点火能量及粉尘含水量对粉尘爆炸特性的影响,对比研究了CaCO_3和Al(OH)_3两种惰性介质的抑爆效果。结果表明:随点火能量增加,粉尘最大爆炸压力和最大升压速率呈线性上升,在高质量浓度下,粉尘爆炸压力受点火能量的影响更显著;添加CaCO_3和Al(OH)_3能够降低玉米淀粉的爆炸压力,相对于CaCO_3的物理抑爆,Al(OH)_3的物理-化学抑爆效果更佳;玉米淀粉粉尘的最大爆炸压力及爆炸升压速率随粉尘含水量降低而不断增大。     

纳米粉体抑制矿井瓦斯爆炸的实验研究

针对目前粉体抑爆剂抑制矿井瓦斯爆炸的局限性,采用自主改进的20 L近球型瓦斯抑爆实验系统进行纳米粉体的抑爆实验。其结果表明:同微米级粉体相比,纳米粉体的抑爆效果更好,甲烷最大爆炸压力、压力上升平均速率分别下降了70.5%和90%以上,爆炸压力峰值时间延长了3倍多;依据纳米粉体表面效应理论,从对爆炸过程中自由基的抑制作用分析了纳米粉体特殊的阻燃抑爆作用,并对纳米粉体及相关技术抑爆进行了展望。     

抑爆粉剂浓度及粒度对瓦斯爆炸抑制效果的影响

抑爆粉剂的参数指标是影响隔抑爆装置抑制瓦斯爆炸效果的重要因素之一。通过20 L球形爆炸特性实验装置对多种不同抑爆粉剂浓度及粒度条件下的瓦斯爆炸特性参数进行了测试。研究表明:随着抑爆剂浓度的逐渐增加，瓦斯爆炸最大压力降低，最大压力上升速率降低，压力到达峰值时间延迟；在20 L密闭环境，粉剂粒度＜15 μm的条件下，当抑爆粉剂浓度增加到225 g/m3时，瓦斯混合气体被完全惰化，失去爆炸性；在15~80 μm抑爆粉剂粒度范围内，随着粒度的减小，抑爆性能先减弱后增强，在抑爆粉剂浓度为200 g/m3时，15 μm 与70~80 μm粉剂粒度最大爆炸压力分别下降了19.8%，17.8%，而40~50 μm粒度爆炸压力下降了6.4%。