活性炭纤维吸附含溴甲烷气体的性能

采用动态吸附法在25℃下,测定了3种活性炭纤维(ACF-1、ACF-2和ACF-3)对含溴甲烷气体的吸附性能和回收效果,并对活性炭纤维的孔结构进行表征.探讨了孔结构、溴甲烷浓度、气体流量、循环使用次数等因素对活性炭纤维吸附溴甲烷性能的影响.结果表明,活性炭纤维比表面积大小及0.4～0.8 nm左右的微孔数量决定了其对溴甲烷吸附性能的优劣;气体中溴甲烷的浓度的提高使活性炭纤维对溴甲烷的穿透和饱和吸附量增加,而气体流量的增加则使活性炭纤维对溴甲烷的穿透和饱和吸附量降低,但两者均使穿透和饱和吸附时间缩短;活性炭纤维多次循环使用后,对溴甲烷的吸附容量明显地降低,循环12次后达到稳定吸附,其稳定吸附值为133.5 mg/g.     

活性炭纤维对染料的吸附性能研究

研究了聚丙烯腈活性炭纤维（P－ACF）、粘胶活性炭纤维（R－ACF）和颗粒活性炭（GAC）对5种红色染料的吸附能力,通过简单的模型,算出5种染料在两种活性炭纤维上的吸附速率常数。结果表明,尽管吸附能力随染料种类不同而有一定的差别,但总体上,聚丙烯腈活性炭纤维的吸附能力略低于颗粒活性炭,而粘胶活性炭纤维的吸附能力则远远优于前两种,对染料有着较大的吸附容量和较快的吸附速率。     

活性炭纤维的氧化处理研究

采用静态保干器法测定了活性炭纤维对乙醇、丙酮、N-甲基吡咯烷酮的吸附量。研究了酸氧化处理对活性炭纤维吸附性能的影响,并用电位滴定法确定了活性炭纤维氧化前后表面含氧官能团的变化。结果表明,活性炭纤维对3种吸附质的吸附量均随时间延长而增加,但饱和吸附量及达到饱和吸附的时间因吸附质的不同而不同。氧化处理后,活性炭纤维表面含氧官能团发生变化,对乙醇的吸附量增加18%,而对N-甲基吡咯烷酮的吸附量提高了300%。     

活性炭纤维的氧化处理研究

采用静态保干器法测定了活性炭纤维对乙醇、丙酮、N-甲基吡咯烷酮的吸附量.研究了酸氧化处理对活性炭纤维吸附性能的影响,并用电位滴定法确定了活性炭纤维氧化前后表面含氧官能团的变化.结果表明,活性炭纤维对3种吸附质的吸附量均随时间延长而增加,但饱和吸附量及达到饱和吸附的时间因吸附质的不同而不同.氧化处理后,活性炭纤维表面含氧官能团发生变化,对乙醇的吸附量增加18%,而对N-甲基吡咯烷酮的吸附量提高了300%.     

吸附法净化低浓度废气实验研究

本文探讨了用活性炭吸附低浓度苯类废气进，空塔气速和气流在吸附层的接触时间对吸附过程的影响，研究了活性炭在已经吸附若干质量的苯类物质以后的吸附。据此绘制了空塔气速一吸附效率和活性炭含苯率一吸附效率等关系曲线，工进行了活性炭再生的研究。研究表明，使用活性炭可以有效地净化低浓度苯类废气。     

银负载对活性炭纤维汞吸附性能的影响

银氨溶液浸渍活性炭纤维制得载银量14.07%的载银活性炭纤维.以筒状吸附体吸附气态Hg0的方式研究活性炭纤维银载前后的汞吸附性能,结果表明,载银后活性炭纤维汞吸附性能明显提高.实验还发现:随吸附温度升高,活性炭纤维的汞吸附效率随先增加后降低,而载银活性炭纤维的汞吸附效率随吸附温度升高而一直降低;延长停留时间和添加H2O(g)对两者汞吸附均有利.采用片状吸附体对2种吸附剂的汞饱和吸附量进行了测定,实验得出:70℃下活性炭纤维汞饱和吸附量为29.4 mg/g,载银活性炭纤维汞饱和吸附量为192.3 mg/g,即活性炭纤维载银后汞饱和吸附量提高到原来的6.54倍.扫描电镜分析发现:活性炭纤维上物理吸附汞占绝大多数,化学吸附汞很少;负载银后汞只吸附在活性炭纤维的含银活性点上,银粒子与汞结合生成银汞齐后形状趋于规则,且主要分布于活性炭纤维微晶的晶棱交界处.     

吸附法净化低浓度废气实验研究

本文探讨了用活性炭吸附低浓度苯类废气时,空塔气速和气流在吸附层的接触时间对吸附过程的影响;研究了活性炭在已经吸附若干质量的苯类物质以后的吸附性能.据此绘制了空塔气建-吸附效率和活性炭含苯率-吸附效率等关系曲线,并进行了活性炭再生的研究.研究表明:使用活性炭可以有效地净化低浓度苯类废气.     

低温等离子体改性活性炭纤维对不同极性苯系物的吸附

探究了不同改性时间下的活性炭纤维孔结构和表面化学性质的变化,并进一步研究了改性后的活性炭纤维对不同极性苯系物的吸附。通过BET比表面积、Boehm滴定分析、FTIR红外光谱对改性前后的活性炭纤维进行表征。结果表明,功率150 W,改性时间为30、60和90 min时,活性炭纤维烧失率随着改性时间延长而升高,分别达到16.5%、27.8%、45.5%。改性过程中,活性炭纤维比表面积和微孔孔容显著增加,有助于改善活性炭纤维吸附性能。在物理吸附和化学吸附作用下,改性活性炭纤维对邻二甲苯、间二甲苯和对二甲苯吸附性能有所提高,其中,改性90 min活性炭纤维对其吸附量分别增加了0.58、0.55和0.44 mg·mg-1。酸性含氧基团由原来的0.973 mmol·g-1增加到1.675 mmol·g-1,改性后酸性含氧官能团的增加使活性炭纤维表面极性增大,有利于对极性有机物邻、间二甲苯吸附量增加率的提高。     

污泥活性炭固定床吸附甲苯

采用ZnCl2化学活化法制备的污泥活性炭用于固定床吸附甲苯实验,研究了吸附剂床层厚度、甲苯初始浓度、气体线速等操作条件对其吸附性能的影响,并建立了污泥活性炭吸附甲苯的传质模型,计算不同操作条件下的传质区长度和物质总传质系数。结果表明,当床层厚度从3 cm增加到7 cm,传质区长度基本不变,物质总传质系数增加了66.66%;当甲苯初始浓度增大3.36倍,传质区长度增加了17.19%,而物质总传质系数降低了22.05%;在实验流速范围内,气体线速变为原来的2倍,物质总传质系数增加了65.27%,说明污泥活性炭对甲苯吸附属于外扩散控制。     

活性炭吸附硫化氢及微波辐照解吸研究

研究了两种活性炭对硫化氢的平衡吸附性能力,并对活性炭床层的穿透性进行了考察;吸附饱和和活性炭在微波辐射的作用下进行解吸。实验表明,解吸效率与微波作用时间及温度有关,在本实验条件下H2S解吸效率达90．1％。     

顶空气相色谱测试水中苯系混合物在不同材料上的吸附行为

设计了正交实验对5种材料吸附模拟废水中苯系混合物(苯、甲苯、二甲苯)的条件进行优化,CD02硅藻土与X型纳米分子筛以2∶1(质量比)进行复合后,对苯系混合物去除效果最好.采用顶空气相色谱法测定8种不同材料对水中苯系混合物的去除情况,结果表明复合材料对苯系混合物具有良好的去除效果,仅次于活性炭.复合材料在pH为7、搅拌时间为25 min、用量为1.8g/L时,对苯系混合物质量浓度为4.0 mg/L模拟废水的平均去除率为87.56％.经过4次再生后,复合材料的再生率仍高达84.90％,对苯系混合物的平均去除率为91.49％.     

Physico-chemical treatments for the complete removal of non-ionic surfactants from effluents

Adsorption isotherms for a selection of non-ionic surfactants on activated carbons indicated the effectiveness of the latter in the removal of these pollutants from secondary effluents. The removal efficiencies were found to be improved when the secondary effluent was first flocculated with ferric chloride. This effectively removed some 80% of the non-ionic surfactant in the effluent. Batch adsorption experiments with powdered activated carbon removed 97% of the surfactant at low carbon dosage. A granular carbon with the best adsorption capacity was selected for continuous-flow operation in which non-ionic surfactants, COD and anionic surfactant alkyl benzene sulphonate were monitored. The breakthrough capacity for the non-ionic surfactants was in excess of 6000 bed volumes throughput of flocculated, sand-filtered effluent in a laboratory scale carbon column. Such a procedure is suggested for the complete removal of such pollutants from effluents.     

Microwave regeneration of activated carbon used for removal of solvents from vented air

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

Microwave Regeneration of Activated Carbon Used for Removal of Solvents from Vented Air

ABSTRACT

A microwave regeneration of activated carbon used to remove organic solvents from vented air has been investigated. Methyl ethyl ketone (MEK), acetone, and tetrachloroethylene (TCE) vapors were removed from vented air through adsorption onto granular activated carbon. The saturated carbon was then regenerated in a microwave field, where the solvent was quickly desorbed and recovered from the inner pores of the carbon granules. The microwave-induced regeneration restored the original adsorption capacity and surface area of the activated carbon.     

可吸附有机卤化物的深度处理实验研究

可吸附有机卤化物（AOX）是人为污染的重要标志之一,北京高碑店污水处理厂二级出水中约90％的AOX为可吸附有机氧化物（AOCl),研究了自氧氧化,粒状活性炭吸附,粉末活性炭吸附3种深度处理工艺对二级出水中AOX的去除作用,臭氧的氧化反应最多可去除约38％的AOX,粒状活性炭床可运行3200床体积,吸附容量为0.14mgAOX/g GH-16型活性炭,投加木质粉末活性炭200mg/L及25mg/L的聚合氯化铝,能去除24．7％的AOX。     

Adsorption characteristics of benzene on biosolid adsorbent and commercial activated carbons

This study selected biosolids from a petrochemical waste-water treatment plant as the raw material. The sludge was immersed in 0.5-5 M of zinc chloride (ZnCl2) solutions and pyrolyzed at different temperatures and times. Results indicated that the 1-M ZnCl2-immersed biosolids pyrolyzed at 500 degrees C for 30 min could be reused and were optimal biosolid adsorbents for benzene adsorption. Pore volume distribution analysis indicated that the mesopore contributed more than the macropore and micropore in the biosolid adsorbent. The benzene adsorption capacity of the biosolid adsorbent was 65 and 55% of the G206 (granular-activated carbon) and BPL (coal-based activated carbon; Calgon, Carbon Corp.) activated carbons, respectively. Data from the adsorption and desorption cycles indicated that the benzene adsorption capacity of the biosolid adsorbent was insignificantly reduced compared with the first-run capacity of the adsorbent; therefore, the biosolid adsorbent could be reused as a commercial adsorbent, although its production cost is high.     

Removal characteristics of trace compounds of landfill gas by activated carbon adsorption

The removal characteristics of trace compounds and moisture in raw landfill gas (LFG) were studied. The LFG from the extraction well was saturated with water and moisture was eliminated by physical methods including cyclone-type dehydrator and compressor. The moisture removal efficiency of dehydrator and compressor was above 80%. As the moisture contents of LFG decreased, the toxic compounds like aromatics and chlorinated compounds were effectively removed by using the granular activated carbon. The breakthrough time and adsorption capacity of benzene, toluene, and ethyl benzene decreased rapidly when the relative humidity is over 60%. The effect of moisture was more pronounced at lower adsorbate concentrations tested than at higher concentrations. The breakthrough curves for multi-component mixtures show displacement effects. In the course of competing adsorption, adsorbates with strong interaction force to displace weakly bounded substances. Adsorption by activated carbon is in descending order of xylene, ethylbenzene, toluene, tri or tetrachloroethylene, benzene, carbon tetrachloride and chloroform in LFG, respectively.     

Adsorption Characteristics of Benzene on Biosolid Adsorbent and Commercial Activated Carbons

Abstract

This study selected biosolids from a petrochemical waste-water treatment plant as the raw material. The sludge was immersed in 0.5-5 M of zinc chloride (ZnCl₂) solutions and pyrolyzed at different temperatures and times. Results indicated that the 1-M ZnCl₂-immersed biosolids pyrolyzed at 500 °C for 30 min could be reused and were optimal biosolid adsorbents for benzene adsorption. Pore volume distribution analysis indicated that the mesopore contributed more than the macropore and micropore in the biosolid adsorbent. The benzene adsorption capacity of the biosolid adsorbent was 65 and 55% of the G206 (granular-activated carbon) and BPL (coal-based activated carbon; Calgon, Carbon Corp.) activated carbons, respectively. Data from the adsorption and desorption cycles indicated that the benzene adsorption capacity of the biosolid adsorbent was insignificantly reduced compared with the first-run capacity of the adsorbent; therefore, the biosolid adsorbent could be reused as a commercial adsorbent, although its production cost is high.     

高比表面积活性炭的制备及对Cr(Ⅵ)吸附的研究

以椰树壳为原料,运用水蒸汽和二氧化碳复合物理活化法在4 h内制备了2 162.84 m2/g的高比表面积活性炭,其孔径分布范围为1.1~2.5 nm。应用此吸附剂考察了溶液pH、吸附剂用量、接触时间和初始浓度对Cr(VI)离子吸附效果的影响,并讨论了固定吸附床中不同溶液流量对Cr(VI)去除效果的影响。结果表明:在温度为298 K、溶液pH为1.96、吸附剂用量为0.10 g、铬离子初始浓度为100 mg/L与接触时间为70 min的条件下,活性炭对铬离子具有较高的吸附容量,去除率高达99.32%;铬离子在吸附床中的穿透曲线具有陡峭的传质锋面,但随着铬离子溶液流量的增大脱除果率降低。