Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.     

Temperature dependence of hydroxyl radical formation in the hv/Fe3+/H2O2 and Fe3+/H2O2 systems

The thermal enhancement of the formation of *OH by the hv/Fe(III)/H2O2 system (including the Fe(III)/H2O2 system) was quantitatively investigated with reaction temperatures ranging from 25 to 50 degrees C. A temperature dependent kinetic model for the hv/Fe(III)/H2O2 system, incorporating 12 major reactions with no fitted rate constants or activation energies, was developed, and successfully explained the experimental measurements. Particularly, the thermal enhancement of Fe(OH)2+ photolysis which is the most significant step in the hv/Fe(III)/H2O2 system was effectively explained by two factors; (1) the variation of the Fe(OH)2+ concentration with temperature, and (2) the temperature dependence of the quantum yield for Fe(OH)2+ photolysis (measured activation energy=11.4 kJ mol(-1)). Although in both the hv/Fe(III)/H2O2 and Fe(III)/H2O2 systems, elevated temperatures enhanced the formation of *OH, the thermal enhancement was much higher in the dark Fe(III)/H2O2 system than the hv/Fe(III)/H2O2 system. Furthermore, it was found that the relative thermal enhancement of the formation of *OH in the presence of *OH scavengers (tert-butyl alcohol) was magnified in the Fe(III)/H2O2 system but was not in the hv/Fe(III)/H2O2 system.     

不同高级氧化法对水中低浓度药物甲硝唑降解过程的比较

采用UV、H₂O₂、UV/H₂O₂、Fenton、UV/Fenton和UV/TiO₂方法，对水中低浓度的药物甲硝唑进行降解。通过HPLC和UV-Vis光谱得到的甲硝唑去除率。详细讨论了Fe²⁺、TiO₂和H₂O₂的初始浓度以及溶液的初始pH值对降解效率的影响。结果表明，UV/Fenton和UV/TiO₂ 2种系统对水中低浓度甲硝唑均有很好的去除效果，但前者的光催化效率更高。在甲硝唑浓度=6 μmol/L，H₂O₂和Fe²⁺的初始浓度分别为0.5 mg/L和2.94 μmol/L，pH=4的条件下，UV/Fenton方法对甲硝唑水溶液光催化的最佳效率为95.8%。     

Quantitation of Hydroxyl Radicals from Photolysis of Fe(III)-Citrate Complexes in Aerobic Water (5 pp)

Background For their high photoreactivity, Fe(III)-carboxylate complexes are important sources of H2O2 for some atmospheric and surface waters. Citrate is one kind of carboxylate, which can form complexes with Fe(III). In our previous study, we have applied Fe(III)-citrate complexes to degrade and decolorize dyes in aqueous solutions both under UV light and sunlight. Results have shown that carboxylic acids can promote the photodegradation efficiency. It is indicated that the photolysis of Fe(III)-citrate complexes may cause the formation of some reactive species (e. g. H2O2 and ·OH). This work is attempted to quantify hydroxyl radicals generated in the aqueous solution containing Fe(III)-citrate complexes and to interpret the photoreactivity of Fe(III)-citrate complexes for degrading organic compounds. Methods By using benzene as the scavenger to produce phenol, the photogeneration of ·OH in the aqueous solution containing Fe (III)-citrate complexes was determined by HPLC. Results and Discussion In the aqueous solution containing 60.0/30.0 mM Fe(III)/citrate and 7.0 mM benzene at pH 3.0, 96.66 mM ·OH was produced after irradiation by a 250W metal halide light (l ≥ 313 nm) for 160 minutes. Effects of initial pH value and concentrations of Fe(III) and citrate on ·OH radical generation were all examined. The results show that the greatest photoproduction of ·OH in the aqueous solution (pH ranged from 3.0 to 7.0) was at pH 3.0. The photoproduction of ·OH increased with increasing Fe(III) or citrate concentrations. Conclusion In the aqueous solutions containing Fe(III)-citrate complexes, ·OH radicals were produced after irradiation by a 250W metal halide light. It can be concluded that Fe(III)-citrate complexes are important sources of ·OH radicals for some atmospheric and surface waters. Recommendations and Outlook It is believed that the photolysis of Fe(III)-citrate complexes in the presence of oxygen play an important role in producing ·OH both in atmospheric waters and surface water where high concentrations of ferric ions and citrate ions exist. The photoproduction of ·OH has a high oxidizing potential for the degradation of a wide variety of natural and anthropogenic organic and inorganic substances. We can use this method for toxic organic pollutants such as organic dyes and pesticides.     

Photo-oxidation of cork manufacturing wastewater

Several photo-activated processes have been investigated for oxidation of a cork manufacturing wastewater. A comparative activity study is made between different homogeneous (H2O2/UV-Vis and H2O2/Fe2+/UV-Vis) and heterogeneous (TiO2/UV-Vis and TiO2/H2O2/UV-Vis) systems, with degradation performances being evaluated in terms of total organic carbon (TOC) removal. Results obtained in a batch photo-reactor show that photo-catalysis with TiO2 is not suitable for this kind of wastewater while the H2O2/UV-Vis oxidation process, for which the effect of some operating conditions was investigated, allows to remove 39% of TOC after 4 h of operation (for C(H2O2)=0.59 M, pH=10 and T=35 degrees C). The combined photo-activated process, i.e., using both TiO2 and H2O2, yields an overall TOC decrease of 46% (for C(TiO2)=1.0 gl(-1)). The photo-Fenton process proved to be the most efficient, proceeds at a much higher oxidation rate and allows to achieve 66% mineralization in just 10 min of reaction time (for C(H2O2)=0.31 M, T=30 degrees C, Fe2+:H2O2=0.12 (mol) and pH=3.2).     

Kinetics of oxidation of chlorobenzenes and phenyl-ureas by Fe(II)/H2O2 and Fe(III)/H2O2. Evidence of reduction and oxidation reactions of intermediates by Fe(II) or Fe(III)

The rates of degradation of 1,2,4-trichlorobenzene (TCB), 2,5-dichloronitrobenzene (DCNB), diuron and isoproturon by Fe(II)/H2O2 and Fe(III)/H2O2 have been investigated in dilute aqueous solution ([Organic compound]0 approximately 1 microM, at 25.0 +/- 0.2 degrees C and pH < or = 3). Using the relative rate method with atrazine as the reference compound, and the Fe(II)/H2O2 (with an excess of Fe(II)) and Fe(III)/H2O2 systems as sources of OH radicals, the rate constants for the reaction of OH* with TCB and DCNB were determined as (6.0 +/- 0.3)10(9) and (1.1 +/- 0.2)10(9) M(-1) s(-1). Relative rates of degradation of diuron and isoproturon by Fe(II)/H2O2 were about two times smaller in the absence of dissolved oxygen than in the presence of oxygen. These data indicate that radical intermediates are reduced back to the parent compound by Fe(II) in the absence of oxygen. Oxidation experiments with Fe(III)/H2O2 showed that the rate of decomposition of atrazine markedly increased in the presence of TCB and this increase has been attributed to a regeneration of Fe(II) by oxidation reactions of intermediates (radical species and dihydroxybenzenes) by Fe(III).     

Degradation of polychlorinated dibenzo-p-dioxins in aqueous solution by Fe(II)/H2O2/UV system

The photodegradation of polychlorinated dibenzo-p-dioxins (PCDDs), which include tetra- to octa-CDDs (TeCDD, PeCDD, HxCDD, HpCDD and OCDD), was carried out in the presence of Fe(II) and H2O2 mixed reagent. The degradation efficiency was strongly influenced by UV irradiation, and the initial concentrations of H2O2 and Fe(II). An initial TeCDD concentration of 10 ng l(-1) was completely degraded within 20 min under the optimum conditions. All PCDDs tested were successfully degraded by Fe(II)/H2O2/UV treatment and complete degradation of TeCDD, PeCDD and HxCDD was achieved within 120 min. PCDD photodegradation rates decreased with the number of chlorine atoms. The degradation process of TeCDD by this system seems to be initiated by an oxidative reaction (OH* radical attack) because less chlorinated DDs as intermediate products were not detected. From the Frontier electron density calculation, the first OH* radical attack positions on TeCDD were found to be four C atoms neighboring two O atoms. The decomposition of TeCDD gave 4,5-dichlorocatechol as an intermediate product. A TeCDD degradation scheme was proposed based on the identified intermediate and the values of Frontier electron density. Based on these results, Fe(II)/H2O2/UV system could be useful technology for the treatment of wastewater containing persistent pollutants such as dioxins and polychlorinated biphenyls.     

Synergy of ozonation and photocatalysis to mineralize low concentration 2,4-dichlorophenoxyacetic acid in aqueous solution

Concentration of 2,4-dichlorophenoxyacetic acid (2,4-D) may affect its degradation kinetics in advanced oxidation systems, and combinations of two or more systems can be more effective for its mineralization at low concentration levels. Degradations and mineralizations of 0.045mM 2,4-D using O(3), O(3)/UV, UV/TiO(2) and O(3)/UV/TiO(2) systems were compared, and influence of reaction temperature on the mineralization in O(3)/UV/TiO(2) system was investigated. 2,4-D degradations by O(3), O(3)/UV and UV/TiO(2) systems were similar to the results of earlier investigations with higher 2,4-D concentrations. The degradations and total organic carbon (TOC) removals in the four systems were well described by the first-order reaction kinetics. The degradation and removal were greatly enhanced in O(3)/UV/TiO(2) system, and further enhancements were observed with larger O(3) supplies. The enhancements were attributed to hydroxyl radical (()OH) generation from more than one reaction pathway. The degradation and removal in O(3)/UV/TiO(2) system were very efficient with reaction temperature fixed at 20 degrees C. It was suspected that reaction temperature might have influenced ()OH generation in the system, which needs further attention.     

Simultaneous oxidation of EDTA and reduction of metal ions in mixed Cu(II)/Fe(III)-EDTA system by TiO2 photocatalysis

Both the photooxidation of EDTA and the photoreduction of metal ions in metal-EDTA systems were investigated. EDTA oxidation by TiO(2) photocatalysis occurred sequentially as Cu(II)-EDTA>Cu(II)/Fe(III)-EDTA>Fe(III)-EDTA. For Cu(II)-EDTA, EDTA was completely decomposed after only 60min of irradiation. The rate of EDTA decomposition was directly correlated with the initial Cu(II) concentration in the case of a mixed Cu(II)/Fe(III)-EDTA system. The metal ions in a single metal-EDTA complex were removed following significant decomposition of EDTA. For a mixed Cu(II)/Fe(III)-EDTA system, however, no copper was removed whereas almost all of the iron was removed. The iron and copper species deposited on the TiO(2) surface were identified via EPR and XPS as mixed FeO/Fe(3)O(4) and Cu(0)/Cu(2)O, respectively.     

Photochemical degradation and mineralization of 4-chlorophenol

INTENTION, GOAL, SCOPE, BACKGROUND: Since the intermediate products of some compounds can be more toxic and/or refractory than the original compund itself, the development of innovative oxidation technologies which are capable of transforming such compounds into harmless end products, is gaining more importance every day. Advanced oxidation processes are one of these technologies. However, it is necessary to optimize the reaction conditions for these technologies in order to be cost-effective. OBJECTIVE: The main objectives of this study were to see if complete mineralization of 4-chlorophenol with AOPs was possible using low pressure mercury vapour lamps, to make a comparison of different AOPs, to observe the effect of the existence of other ions on degradation efficiency and to optimize reaction conditions. METHODS: In this study, photochemical advanced oxidation processes (AOPs) utilizing the combinations of UV, UV/H2O2 and UV/H2O2/Fe2+ (photo-Fenton process) were investigated in labscale experiments for the degradation and mineralization of 4-chlorophenol. Evaluations were based on the reduction of 4-chlorophenol and total organic carbon. The major parameters investigated were the initial 4-chlorophenol concentration, pH, hydrogen peroxide and iron doses and the effect of the presence of radical scavengers. RESULTS AND DISCUSSION: It was observed that the 4-chlorophenol degradation efficiency decreased with increasing concentration and was independent of the initial solution pH in the UV process. 4-chlorophenol oxidation efficiency for an initial concentration of 100 mgl(-1) was around 89% after 300 min of irradiation in the UV process and no mineralization was achieved. The efficiency increased to > 99% with the UV/H2O2 process in 60 min of irradiation, although mineralization efficiency was still around 75% after 300 min of reaction time. Although the H2O2/4-CP molar ratio was kept constant, increasing initial 4-chlorophenol concentration decreased the treatment efficiency. It was observed that basic pHs were favourable in the UV/H2O2 process. The results showed that the photo-Fenton process was the most effective treatment process under acidic conditions. Complete disappearance of 100 mgl(-1) of 4-chlorophenol was achieved in 2.5 min and almost complete mineralization (96%) was also possible after only 45 min of irradiation. The efficiency was negatively affected from H2O2 in the UV/H2O2 process and Fe2+ in the photo-Fenton process over a certain concentration. The highest negative effect was observed with solutions containing PO4 triple ions. Required reaction times for complete disappearance of 100 mgl(-1) 4-chlorophenol increased from 2.5 min for an ion-free solution to 30 min for solutions containing 100 mgl(-1) PO4 triple ion and from 45 min to more than 240 min for complete mineralization. The photodegradation of 4-chlorophenol was found to follow the first-order law. CONCLUSION: The results of this study showed that UV irradiation alone can degrade 4-CP, although at very slow rates, but cannot mineralize the compound. The addition of hydrogen peroxide to the system, the so-called UV/H2O2 process, significantly enhances the 4-CP degradation rate, but still requires relatively long reaction periods for complete mineralization. The photo-Fenton process, the combination of homogeneous systems of UV/H2O2/Fe2+ compounds, produces the highest photochemical elimination rate of 4-CP and complete mineralization is possible to achieve in quite shorter reaction periods when compared with the UV/H2O2 process. RECOMMENDATIONS AND OUTLOOK: It is more cost effective to use these processes for only purposes such as toxicity reduction, enhancement of biodegradability, decolorization and micropollutant removal. However the most important point is the optimization of the reaction conditions for the process of concern. In such a case, AOPs can be used in combination with a biological treatment systems as a pre- or post treatment unit providing the cheapest treatment option. The AOP applied, for instance, can be used for toxicity reduction and the biological unit for chemical oxygen demand (COD) removal.     

Fe-exchanged zeolite as the effective heterogeneous Fenton-type catalyst for the organic pollutant minimization: UV irradiation assistance

The issue of investigations in this study was an application of heterogeneous Fenton-type catalyst, Fe-exchanged zeolite FeZSM5, for the minimization of phenol and overall organic content in the model wastewater. Applied treatment systems included variation of heterogeneous and homogeneous Fenton-type catalyst with and without the assistance of UV irradiation, FeZSM5/H2O2, Fe2+/H2O2/NH4ZSM5, Fe3+/H2O2/NH4ZSM5, UV/FeZSM5/H2O2, UV/Fe2+/H2O2/NH4ZSM5 and UV/Fe3+/H2O2/NH4ZSM5. Processes efficiency was evaluated on the basis of phenol removal, mineralization extent, H2O2 consumption and concentration of iron ions in the bulk after the treatment. By all applied systems, complete phenol removal was achieved in less than 30 min of treatment time. Systems including heterogeneous Fenton-type catalyst showed somewhat lower mineralization efficiency in comparison to the corresponding systems applying homogeneous Fenton-type catalysts and the addition of synthetic zeolite NH4ZSM5. Significantly lower concentration of iron ions in the bulk after the treatment could give these systems, particularly UV/FeZSM5/H2O2, a great advantage over the homogeneous Fenton-type systems.     

Fate of a stilbene-type fluorescent whitening agent (DSBP) in the presence of Fe(III) aquacomplexes: from the redox process to the photodegradation

The behaviour of 4,4′-bis(2-sulfostyryl)biphenyl (DSBP), a fluorescent whitening agent, was investigated in the presence of Fe(III) aquacomplexes at room temperature. In the dark, a two-step reaction was observed when adding Fe(III) to a solution of DSBP: an initial fast redox reaction between DSBP and the monomeric species Fe(OH)²⁺ and a slower reaction leading to the coagulation of oxidised DSBP and iron. This phenomenon is due to the formation of a complex or an ion-pair between Fe(II) and/or Fe(III) with oxidised DSBP and it probably occurs by charge neutralisation in our experimental conditions. The precipitation of DSBP depends on the initial concentration in Fe(OH)²⁺ and is achieved for a ratio [Fe(OH) ²⁺]/[DSBP] of 5 approximately. Under irradiation at 365 nm, a complicated behaviour was observed: a complexation of iron by oxidised DSBP favoured by irradiation and a degradation of DSBP induced by an intramolecular electron transfer in the complex or by a photoredox of Fe(OH)²⁺ species generating OH radicals in the supernatant. The complete degradation of DSBP is reached four times faster in the presence of Fe(III) with respect to the direct photolysis of DSBP alone. Moreover, the total mineralization of DSBP obtained in less than 120 h upon irradiation at 365 nm is only observed in the presence of the ferric ions, enlightening the efficiency of the method involving Fe(III) and UV irradiation.     

Comparative study of the oxidation of atrazine and acetone by H2O2/UV, Fe(III)/UV, Fe(iii)/H2O2/UV and Fe(II) or Fe(III)/H2O2

In this study, the rates of degradation of organic compounds by several AOPs (H₂O₂/UV, Fe(III)/UV, Fe(III)/H₂O₂/UV, Fe(II)/H₂O₂ and Fe(III)/H₂O₂) have been compared. Experiments were carried out at pH ≈ 3 (perchloric acid / sodium perchlorate solutions) and with UV reactors equipped with a low-pressure mercury vapour lamp (emission at 253.7 run). The data obtained with atrazine ([Atrazine]_o = 100 μg/L) showed that the rate of degradation of atrazine in very dilute aqueous solution is much more rapid with Fe(III)/UV than with H₂O₂/UV. Photo-Fenton process (Fe(III)/H₂O₂/UV) was found to be more efficient than H₂O₂/UV and Fe(II)/H₂O₂ for the mineralization of acetone ([Acetone]_o = 1 mM).     

Fresnel lens to concentrate solar energy for the photocatalytic decoloration and mineralization of orange II in aqueous solution

The decoloration and mineralization of the azo dye orange II under conditions of artificial ultraviolet light and solar energy concentrated by a Fresnel lens in the presence of hydrogen peroxide and TiO(2)-P25 was studied. A comparative study to demonstrate the viability of this solar installation was done to establish if the concentration reached in the focus of the Fresnel lens was enough to improve the photocatalytic degradation reaction. The degradation efficiency was higher when the photolysis was carried out under concentrated solar energy irradiation as compared to UV light source in the presence of an electron acceptor such us H(2)O(2) and the catalyst TiO(2). The effect of hydrogen peroxide, pH and catalyst concentration was also determined. The increase of H(2)O(2) concentration until a critical value (14.7 mM) increased both the solar and artificial UV oxidation reaction rate by generating hydroxyl radicals and inhibiting the (e(-)/h(+)) pair recombination, but the excess of hydrogen peroxide decreases the oxidation rate acting as a radical or hole scavenger and reacting with TiO(2) to form peroxo-compounds, contributing to the inhibition of the reaction. The use of the response surface methodology allowed to fit the optimal values of the parameters pH and catalyst concentration leading to the total solar degradation of orange II. The optimal pH range was 4.5-5.5 close to the zero point charge of TiO(2) depending on surface charge of catalyst and dye ionization state. Dosage of catalyst higher than 1.1 gl(-1) decreases the degradation efficiency due to a decrease of light penetration.     

Fe<Superscript>0</Superscript>-based system as innovative technology for degrading trichloromethane: Redox removal characteristics

BACKGROUND: The spent waste of aliphatic chlorinated solvents has caused severe deterioration of groundwater quality. Trichloromethane (TCM), which shows health and toxicological effects on human beings, was selected as a model compound to be dechlorinated through a redox system. METHODS: The Fe0-based system including Fe0/H2O, Fe0/UV, Fe0/H2O2, and Fe0/UV/H2O2 was explored to evaluate its performance in dechlorinating TCM. H2O2 was dosed at later reaction time points to initiate Fenton or photo-Fenton reactions. The first two systems demonstrate the reductive dechlorination of TCM by Fe0-released electrons, while the latter two show dechlorination of TCM by both electron reduction and hydroxyl radical oxidation. The system parameters of TCM remaining, Cl- buildup, Fe2+ accumulation, H2O2 residue, and ORP were measured to describe different redox characteristics of TCM dechlorination. The Cl- buildup was used as a way to describe the degree of TCM dechlorination in an open reaction system. RESULTS: Reductive dechlorination efficiencies of TCM were 5% and 6% for the systems of Fe0/H2O and Fe0/UV, respectively. In contrast, the Fe/H2O2 and Fe0/UV/H2O2 systems were capable of dechlorinating TCM reductively and oxidatively by 14% and 15%, respectively. The presence of UV light was found to retard the dissolution of Fe2+, but it enhanced the rate of chloride buildup, based on the comparison of Fe0/H2O and Fe0/UV systems. In addition, WV irradiation plays only a minor role in the Fe0/UV/H2O2 system, in view of TCM dechlorination. Application of small amount of H2O2 results in the increase of Fe2+ accumulation rate in the Fe0/H2O2 system. CONCLUSIONS: TCM was dechlorinated mostly through post Fenton oxidation; reductive reaction represents a less efficient way to dechlorinate TCM. The efficiencies of overall TCM dechlorination for the two systems of Fe0/H2O2 and Fe0/UV/ H2O2 are comparable to each other, and this implies that the presence of UV irradiation imposes no significant enhancement. RECOMMENDATIONS AND OUTLOOKS: It is highly recommended to initiate effective redox dechlorination of TCM with the system of Fe0/H2O2, where the H2O2 in excess is applied at a later reaction time point.     

Degradation of calcium lignosulfonate using gamma-ray irradiation

Gamma-ray irradiation was proven to be a promising means for the removal of calcium lignosulfonate (CaLS). At a dose rate of 55Gy min(-1), over 90% of CaLS was mineralized to CO(2), H(2)O and sulfates within 3-d irradiation. The degradation of CaLS with the initial CaLS concentrations ranging from 40 to 200mg l(-1) followed zero-order kinetics at the dose rates of 16-150Gy min(-1). The zero-order degradation rate constant was functionally related with irradiation dose rate. Experiments performed with or without addition of radical scavengers demonstrated that the role of *OH was predominant in CaLS degradation and the reductive species made minor contributions to CaLS degradation. Addition of appropriate amounts of H(2)O(2) significantly enhanced the mineralization of CaLS, e.g., addition of 10mM H(2)O(2) at a dose rate of 55Gy min(-1) elevated the mineralization rate constant by five times. The addition of Fenton's reagent to irradiated CaLS solutions facilitated the degradation of CaLS, but no obviously synergistic effect was observed.     

Fe(III)-oxalate complexes induced photooxidation of diethylstilbestrol in water

In this work, the photooxidation of diethylstilbestrol (DES), a synthetic estrogen, was investigated in a concentric reactor under a 125 W high-pressure mercury lamp (lambda > or = 365 nm). The photooxidation efficiencies were dependent on the pH values and Fe(III)/oxalate ratios of the system, with higher efficiency at pH 3.50+/-0.05 and Fe(III)/oxalate ratio 10.0/120.0 micromol l(-1). The photooxidation reactions obeyed the law of pseudo-first-order reaction at the concentration over the range of 2.0-10.0 mg l(-1) of DES. The photooxidation rates decreased with increasing the initial concentrations of DES. For 2.0 mg l(-1) DES, the observed photooxidation rate coefficient (k(obs)) was 0.00622 min(-1). By using GC-MS and LC-MS techniques, the predominant photooxidation products DES-o-catechol ([M](+), m/z 284) and DES-4-semiquinone ([M](-), m/z 267) were respectively identified and the mechanisms for the oxidative degradation were proposed. When DES reacted with OH radicals, C atoms in 3-position were added with OH radicals to produce hydrolyzed DES radical followed by two oxidation pathways: (1) dehydrolyzing to produce DES-4-semiquinone which was oxidized further to DES-4,4'-quinone; (2) undergoing peroxidation by O(2) and getting rid of HO(2) radical to produce DES-o-catechol. After that, the two H atoms on the hydroxy group of the catechol were extracted in two individual steps to form intermediates semiquinone radical and o-quinone. The catechol intermediates underwent further oxidation, benzene ring cleavage and decarboxylation, up to mineralization ultimately.     

Homogeneous degradation of 1,2,9,10-tetrachlorodecane in aqueous solutions using hydrogen peroxide, iron and UV light

The homogeneous degradation of the polychlorinated n-alkane, 1,2,9,10-tetrachlorodecane (T4C10), was studied in aqueous solutions of hydrogen peroxide, including Fenton and photo-Fenton reaction conditions. All solutions were adjusted to a pH of 2.8 and an ionic strength of 0.1 M NaClO4 prior to photolysis. T4C10 (2 x 10(-6) M) was substantially degraded by the H2O2/UV system (1.0 x 10(-2) M H2O2), with 60% disappearance in 20 min of irradiation in a photoreactor equipped with 300 nm lamps of light intensity 3.6 x 10(-5) Ein L(-1) min(-1) (established by ferrioxalate actinometry). The reaction produced stoichiometric amounts of chloride ion indicating complete dechlorination of the chlorinated n-alkane. T4C10 degraded very slowly under Fenton (Fe2+/H2O2/dark) and Fenton-like (Fe3+/H2O2/dark) conditions. However, when the same solutions were irradiated, T4C10 degraded more rapidly than in the H2O2/UV system, with 61% disappearance in 10 min of exposure. The rapid degradation is related to the enhanced degradation of hydrogen peroxide to oxidizing *OH radicals under photo-Fenton conditions. Degradation was inhibited in both the H2O2/UV and photo-Fenton systems by the addition of KI and tert-butyl alcohol due to *OH scavenging.     

Treatment of oily port wastewater effluents using the ultraviolet/hydrogen peroxide photodecomposition system.

This paper presents the nonselective degradation of mechanically pretreated oily wastewater by hydrogen peroxide (H2O2) in the presence and absence of UV irradiation. The effect of chemical oxidation on wastewater biodegradability was also examined. The exclusive use of H2O2 photolyzed by daylight results in quite efficient degradation rates for the low peroxide concentrations used. Higher hydrogen peroxide concentrations inhibit degradation of organic contaminants in the wastewater. The degradation rates of all contaminants are relatively high with an advanced oxidation system (UV/H2O2), but degradation efficiencies are not distinguishably different when 20 or 45 minutes of UV irradiation is used. The excess of H2O2 used in the process can inhibit phenolic degradation and may lead to the formation of a new phenolic fraction. The biodegradability of port wastewater did not increase significantly following the application of the advanced oxidation process.     

TiO₂ supported over SBA-15: an efficient photocatalyst for the pesticide degradation using solar light

Photocatalytic degradation and mineralization of pesticides are studied over TiO(2) supported mesoporous SBA-15 composite system using solar light. TiO(2) is immobilized over SBA-15 by solid sate dispersion method. The catalysts are characterized by XRD, surface area, UV-Vis diffused reflectance spectra, SEM and TEM. The detailed photocatalytic degradation studies are carried out over TiO(2), SBA-15 and different TiO(2) wt% supported SBA-15. The activity evaluation parameters such as catalyst amount, pH, and pollutant initial concentration are studied taking isoproturon as a model compound and established conditions for pesticide degradation. The optimum degradation is achieved over 10 wt% TiO(2)/SBA-15 within 30 min and the reaction is following pseudo-first order kinetics. The isoproturon mineralization is monitored with TOC reduction and it takes around 9h for disappearance. The commercial pesticide solutions containing imidacloprid and phosphamidon are also successfully degraded over these composites with the established conditions. The data indicates that 10 wt% TiO(2)/SBA-15 composite is an effective and highly active system for the pesticide degradations.