利用GPS-RIK技术进行既有线曲线整正测量研究

既有线曲线整正测量是铁路既有线提速改造和工务部门大修设计的主要任务之一。需要改造的既有铁路一般均为繁忙干线，并行车密度较高。传统的测量方法是将测量仪器安置在线路上，这样不仅在作业过程中受行车干扰，作业效率也不够高，而曲线地段通视条件差，作业难度是相当大的。同时，作业人员的安全问题也变得十分突出。笔者提出采用先进的GPS-RIK技术，对既有线曲线整正进行测量。采用该技术不仅能克服气候条件的限制，而且能以较高的频率，较高的精度测定互不通视的各被测点的坐标，克服了传统的作业方法要求置镜点与被测点之间必须通视、作业受天气影响、存在误差累积、内业计算工作量大等缺陷。该法在保证作业人员安全的前提下大大提高作业效率。     

利用GPS-RTK技术进行既有线曲线整正测量研究

既有线曲线整正测量是铁路既有线提速改造和工务部门大修设计的主要任务之一。需要改造的既有铁路一般均为繁忙干线,并行车密度较高。传统的测量方法是将测量仪器安置在线路上,这样不仅在作业过程中受行车干扰,作业效率也不够高,而曲线地段通视条件差,作业难度是相当大的。同时,作业人员的安全问题也变得十分突出。笔者提出采用先进的GPS-RTK技术,对既有线曲线整正进行测量。采用该技术不仅能克服气候条件的限制,而且能以较高的频率,较高的精度测定互不通视的各被测点的坐标,克服了传统的作业方法要求置镜点与被测点之间必须通视、作业受天气影响、存在误差累积、内业计算工作量大等缺陷。该法在保证作业人员安全的前提下大大提高作业效率。     

High beam headlamp use rates: Effects of rurality,proximity of other traffic,and roadway curvature

Objective: The few observational studies of the prevalence of high beam use indicate the rate of high beam use is about 25% when vehicles are isolated from other vehicles on unlit roads. Recent studies were limited to 2-lane rural roads and used measurement methods that likely overestimated use. The current study examined factors associated with the rate of high beam use of isolated vehicles on a variety of roadways in the Ann Arbor, Michigan area.

Methods: Twenty observation sites were categorized as urban, rural, or on a rural/urban boundary and selected to estimate the effects of street lighting, road curvature, and direction of travel relative to the city on high beam use. Sites were selected in pairs so that a majority of traffic passing one site also passed through the other. Measurement of high beams relied on video data recorded for 2 nights at each site, and the video data also were used to derive a precise measure of the proximity of other traffic. Nearly 3,200 isolated vehicles (10 s or longer from other vehicles) were observed, representing 1,500-plus vehicle pairs.

Results: Across the sample, 18% of the vehicles used high beams. Seventy-three percent of the 1,500-plus vehicle pairs used low beams at each paired site, whereas 9% used high beams at both sites. Vehicles at rural sites and sites at the boundaries of Ann Arbor were more likely to use high beams than vehicles at urban sites, but use in rural areas compared with rural/urban boundary areas did not vary significantly. Rates at all sites were much lower than expected, ranging from 0.9 to 52.9%. High beam use generally increased with greater time between subject vehicles and leading vehicles and vehicles in the opposing lane. There were mixed findings associated with street lighting, road curvature, and direction of travel relative to the city.

Conclusion: Maximizing visibility available to drivers from headlights includes addressing the substantial underuse of high beam headlamps. Advanced technologies such as high beam assist, which switches automatically between high and low beam headlamps depending on the presence of other traffic, can help to address this problem.     

基于MATLAB分析的城市道路照明环境比

基于驾驶员在行驶过程中的注意力大部分集中在车辆的正前方,忽略了道路两侧的情况的视觉特性,更容易引发交通事故的问题。环境比为评价路边物体可视度的指标,为了保证评价的准确性,尤其是保障夜间行驶的良好视觉环境,可以根据路灯设置的基本原则及照明强度与可见度的关联特性,使用MATLAB(矩阵实验室)对环境比进行模拟分析,从理论的角度研究其相关的影响因素,提出了采取减小灯具倾斜角、缩短灯具悬臂悬挑长度以及增加路灯灯杆安装位置与路缘石的距离等措施可以提高道路照明环境比的观点,可以作为路灯改造工程、路灯灯具外形的设计以及夜间行驶事故分析的理论基础。     

Inflation of subordinates' performance ratings: main and interactive effects of rater negative affectivity,documentation of work behavior,and appraisal visibility

We hypothesized that raters' tendency to deliberately inflate performance appraisal ratings of subordinates would be associated with rater negative affectivity (NA) and two characteristics of the performance appraisal context: documentation of subordinates' work behaviors and appraisal visibility. We further hypothesized interactions among these variables, such that high‐NA, but not low‐NA raters, would be more likely to inflate ratings under conditions of low documentation and high appraisal visibility. Moreover, we predicted that NA would be associated most strongly with rating inflation when documentation was low and appraisal visibility was high, simultaneously. Results from a sample of 148 supervisors from a variety of organizations supported these hypotheses. We discuss several practical implications of the results and suggest areas for future inquiry. Copyright © 1999 John Wiley & Sons, Ltd.     

Examining crash injury severity and barrier-hit outcomes from cable barriers and strong-post guardrails on Alabama’s interstate highways

Introduction: This study investigates the impact of several risk factors (i.e., roadway, driver, vehicle, environmental, and barrier-specific characteristics) on the injury severity resulting from barrier-related crashes and also on barrier-hit outcomes (i.e., vehicle containment, vehicle redirection, and barrier penetration). A total of 1,685 barrier-related crashes, which occurred on three major interstate highways (I-65, I-85, and I-20) in the state of Alabama, were collected for a seven-year period (2010–2016), and all relevant information from the police reports was reviewed. Features that were rarely explored before (e.g., median width, barrier length, barrier offset or lateral position, left shoulder width, blockout type, and number of cables) were also collected and examined. Two types of longitudinal barriers were analyzed: high-tension cable barriers installed on medians and strong-post guardrails installed on medians and/or roadsides. Method: Two separate mixed logit (MXL) models were used to analyze crash injury severity in median and roadside barrier-related crashes. Two additional MXL models were separately adopted for median and roadside barrier-related crashes to estimate the probability of three barrier-hit outcomes (vehicle containment, vehicle redirection, and barrier penetration). Results: The results of crash injury severity MXL models showed that, for both median and roadside barrier crashes, barrier penetration, female drivers, and driver fatigue were associated with a higher probability of injury or fatal crashes. The results of barrier-hit MXL models showed that longer barrier length, Brifen cable barrier system, and barrier lateral position were significant predictors of median barrier-hit outcomes, whereas dark lighting condition, driving under the influence (DUI), presence of curved freeway sections, and right shoulder width significantly contributed to roadside barrier-hit outcomes. Conclusions: The MXL model succeeded in identifying several contributing factors of crash severity and barrier-hit outcomes along Alabama’s interstate highways. Practical applications: One study application is to design longer barrier run length (greater than 1230 feet or 0.2 miles) to reduce the barrier penetration likelihood.     

真实世界和虚拟场景下行人绕障的实验研究

为了研究利用虚拟现实开展行人疏散实验的有效性以及虚拟场景里不同控制方式的优劣,开展了真实世界与三种不同控制方式(头显-鼠标(HM)、鼠标-鼠标(MM)、键盘-鼠标(KM))下虚拟场景的绕障实验。分析并比较了平均轨迹、绕障距离、绕障起始时间以及归一化时间下的横向距离。实验结果表明,当横向坐标小于1 m时,虚拟场景与真实世界实验平均轨迹的差值在10 cm之内。平均轨迹、绕障距离、绕障起始时间方面,HM更接近真实世界实验;归一化时间下的横向距离方面,MM更接近真实世界实验。     

Kinematics of the unrestrained vehicle occupants in side-impact crashes

A test series involving direct right-side impact of a moving wall on unsupported, unrestrained cadavers with no arms was undertaken to better understand human kinematics and injury mechanisms during side impact at realistic speeds. The tests conducted provided a unique opportunity for a detailed analysis of the kinematics resulting from side impact. Specifically, this study evaluated the 3-dimensional (3D) kinematics of 3 unrestrained male cadavers subjected to lateral impact by a multi-element load wall carried by a pneumatically propelled rail-mounted sled reproducing a conceptual side crash impact. Three translations and 3 rotations characterize the movement of a solid body in the space, the 6 degrees of freedom (6DoF) kinematics of 15 bone segments were obtained from the 3D marker motions and computed tomography (CT)-defined relationships between the maker array mounts and the bones. The moving wall initially made contact with the lateral aspect of the pelvis, which initiated lateral motion of the spinal segments beginning with the pelvis and moving sequentially up through the lumbar spine to the thorax. Analyzing the 6DoF motions kinematics of the ribs and sternum followed right shoulder contact with the wall. Overall thoracic motion was assessed by combining the thoracic bone segments as a single rigid body. The kinematic data presented in this research provides quantified subject responses and boundary condition interactions that are currently unavailable for lateral impact.     

Investigating lane change behaviors and difficulties for senior drivers using naturalistic driving data

Introduction: Lane changes can be a complicated maneuver occurring a dynamic environment requiring the integration of many streams of information. Older drivers may struggle with lane changes which may elevate crash risk. Methods: Real-world lane change behaviors were examined using the Second Strategic Highway Research Program Naturalistic Driving Study database. A total of 393 lane changes were observed for two age groups: middle-aged (30–49), and older (70+) drivers. Results: Older drivers were highly likely to fail to execute an over-the-shoulder glance prior to initiation of a lane change (in 98% of left lane changes and 92% for right lane changes). Older drivers also showed higher rates of OTS glance errors at any point during the lane change in 95% of left lane changes and 86% of right-lane changes. Additionally, older drivers frequently failed to activate the turn signal prior to lane change initiation (60% of lane changes for right changes and 59% for left lane changes). Of the older drivers that made side mirror glances, many occurred after the initiation of the maneuver (46% of left lane changes and 58% of right lane changes) suggesting glances were occurring while changing lanes. Conclusions: Results for older drivers showed that many key glances (particularly side mirror checks) and turn signal actuations observed in the current study occurred after the initiation of the lane change, ostensibly when this action may be too late to gather relevant information and avoid a conflict. Practical Applications: Knowledge of glance patterns during lane changes for older drivers can help older drivers maintain travel mobility as they age. Either through training to reinforce OTS and side mirror glances, or supplemental devices like convex mirrors or oversized rearview mirrors, older drivers can reduce high-risk lane change maneuvers and help older drivers to maintain their mobility and independence longer.     

Socio-demographic and experience factors affecting drivers’ runoff risk along horizontal curves of two-lane rural highway

Introduction: An improper driving strategy is one of the causative factors for a high probability of runoff and overturning crashes along the horizontal curves of two-lane highways. The socio-demographic and driving experience factors of a driver do influence driving strategy. Hence, this paper explored the effect of these factors on the driver’s runoff risk along the horizontal curves. Method: The driving performance data of 48 drivers along 52 horizontal curves was recorded in a fixed-base driving simulator. The driving performance index was estimated from the weighted lateral acceleration profile of each driver along a horizontal curve. It was clustered and compared with the actual runoff events observed during the experiment. It yielded high, moderate, and low-risk clusters. Using cross-tabulation, each risk cluster was compared with the socio-demographic and experience factors. Further, generalized mixed logistic regression models were developed to predict the high-risk and high to moderate risk events. Results: The age and experience of drivers are the influencing factors for runoff crash. The high-risk event percentage for mid-age drivers decreases with an increase in driving experience. For younger drivers, it increases initially but decreases afterwards. The generalized mixed logistic regression models identified young drivers with mid and high experience and mid-age drivers with low-experience as the high-risk groups. Conclusions: The proposed index parameter is effective in identifying the risk associated with horizontal curves. Driver training program focusing on the horizontal curve negotiation skills and graduated driver licensing could help the high-risk groups. Practical applications: The proposed index parameter can evaluate driving behavior at the horizontal curves. Driving behavior of high-risk groups could be considered in highway geometric design. Motor-vehicle agencies, advanced driver assistance systems manufacturers, and insurance agencies can use proposed index parameter to identify the high-risk drivers for their perusal.     

考虑附加效益的设备维修工作综合评价研究

分析在维修工作评价中嵌入附加效益的作用,建立一个反映维修效果和费用的维修工作评价指标体系.根据考虑附加效益的维修评价要求,采用改进的数据包络分析法(IDEA)模型对维修方案进行量化分析.评价结果给出了考虑维修附加值因素的设备维修工作综合评价的优劣排序,为维修技术性、经济性和环境协调性等方面综合权衡提供参考和依据.     

生物质液化燃油代用燃料的应用及展望

主要介绍了生物质液化燃油代用燃料的概念、特点及优势,分析了其它几种代用燃料优势与不足,并阐明了生物质液化燃油代用燃料发展的必然趋势.     

THOR dummy chest deflection response in oblique and lateral far-side sled tests

Abstract

Objective: The focus of this study is side impact. Though occupant injury assessment and protection in nearside impacts has received considerable attention and safety standards have been promulgated, field studies show that a majority of far-side occupant injuries are focused on the head and thorax. The 50th percentile male Test Device for Human Occupant Restraint (THOR) has been used in oblique and lateral far-side impact sled tests, and regional body accelerations and forces and moments recorded by load cells have been previously reported. The aim of this study is to evaluate the chestband-based deflection responses from these tests.

Methods: The 3-point belt–restrained 50th percentile male THOR dummy was seated upright in a buck consisting of a rigid flat seat, simulated center console, dashboard, far-side side door structure, and armrest. It was designed to conduct pure lateral and oblique impacts. The center console, dashboard, simulated door structure, and armrest were covered with energy-absorbing materials. A center-mounted airbag was mounted to the right side of the seat. Two 59-gage chestbands were routed on the circumference of the thorax, with the upper and lower chestbands at the level of the third and sixth ribs, respectively, following the rib geometry. Oblique and pure lateral far-side impact tests with and without airbags were conducted at 8.3 m/s. Maximum chest deflections were computed by processing temporal contours using custom software and 3 methods: Procedures paralleling human cadaver studies, using the actual anchor point location and actual alignment of the InfraRed Telescoping Rods for the Assessment of Chest Compression (IR-TRACC) in the dummy on each aspect—that is, right or left,—and using the same anchor location of the internal sensor but determining the location of the peak chest deflection on the contour confined to the aspect of the sensor; these were termed the SD, ID, and TD metrics, respectively.

Results: All deformation contours at the upper and lower thorax levels and associated peak deflections are given for all tests. Briefly, the ID metrics were the lowest in magnitude for both pure lateral and oblique modes, regardless of the presence or absence of an airbag. This was followed by the TD metric, and the SD metric produced the greatest deflections.

Conclusion: The chestbands provide a unique opportunity to compute peak deflections that parallel current IR-TRACC-type deflections and allow computation of peak deflections independent of the initial point of attachment to the rib. The differing locations of the peak deflection vectors along the rib contours for different test conditions suggest that a priori attachment is less effective. Further, varying magnitudes of the differences between ID and TD metrics underscore the difficulty in extrapolating ID outputs under different conditions: Pure lateral versus oblique, airbag presence, and thoracic levels. Deflection measurements should, therefore, not be limited to an instrument that can only track from a fixed point. For improved predictions, these results suggest the need to investigate alternative techniques, such as optical methods to improve chest deflection measurements for far-side occupant injury assessment and mitigation.     

双火源条件下的XPS火蔓延速率研究

为研究挤塑聚苯乙烯泡沫板(XPS)双火源火焰迁移规律,在不同间距(0.5cm~8cm)的情况下,进行了竖直和水平方向的系列实验。研究发现:火蔓延速率和质量损失速率均随间距先上升后缓慢下降;在竖直方向实验中,火蔓延速率极值点右偏移于质量损失极值点。基于双火源条件下所得到的热解区传热系数,计算出火蔓延速率,进而分析火蔓延速率计算式中对流项和辐射项,得出火蔓延速率随间距的变化主要受控于传热系数。依据此结论解释了火蔓延速率和质量损失趋势相似但两者极值点偏移不同的原因。     

Exploring relationships between observed activation rates and functional attributes of lane departure prevention

Objective: Drivers’ use of lane departure warning and prevention systems is lower than use of other crash avoidance technologies and varies significantly by manufacturer. One factor that may affect use is how well a system prevents unintended departures. The current study evaluated the performance of systems that assist in preventing departures by providing steering or braking input in a 2016 Chevrolet Malibu, 2016 Ford Fusion, 2016 Honda Accord, and 2018 Volvo S90. These vehicles were selected because a prior observational study found that the percentage of privately owned vehicles that had lane departure prevention systems turned on varied among these 4 automakers.

Method: In each vehicle, a test driver induced 40 lane drifts on left and right curves by steering the vehicle straight into the curve so that vehicles departed in the opposite direction and 40 lane drifts on straightaways by slight steering input to direct the vehicle to left and right lane markers.

Results: Vehicles from automakers with higher observed lane departure prevention use rates (Volvo, Chevrolet) featured systems that provided steering input earlier and more often avoided crossing lane markers by more than 35?cm compared to vehicles from automakers with lower observed use rates (Ford, Honda).

Conclusion: The study identified functional characteristics (i.e., timing of steering input, prevention of departures more than 35?cm) of lane departure prevention systems that were strongly associated with observed activation of these systems in privately owned vehicles. Although this relationship does not imply causation, the findings support the hypothesis that functional characteristics of lane departure prevention systems affect their use. Designers may be able to use these results to maximize driver acceptance of future implementations of lane departure prevention.     

Development and Validation of the Total HUman Model for Safety (THUMS) Toward Further Understanding of Occupant Injury Mechanisms in Precrash and During Crash

Objective: Active safety devices such as automatic emergency brake (AEB) and precrash seat belt have the potential to accomplish further reduction in the number of the fatalities due to automotive accidents. However, their effectiveness should be investigated by more accurate estimations of their interaction with human bodies. Computational human body models are suitable for investigation, especially considering muscular tone effects on occupant motions and injury outcomes. However, the conventional modeling approaches such as multibody models and detailed finite element (FE) models have advantages and disadvantages in computational costs and injury predictions considering muscular tone effects. The objective of this study is to develop and validate a human body FE model with whole body muscles, which can be used for the detailed investigation of interaction between human bodies and vehicular structures including some safety devices precrash and during a crash with relatively low computational costs.

Methods: In this study, we developed a human body FE model called THUMS (Total HUman Model for Safety) with a body size of 50th percentile adult male (AM50) and a sitting posture. The model has anatomical structures of bones, ligaments, muscles, brain, and internal organs. The total number of elements is 281,260, which would realize relatively low computational costs. Deformable material models were assigned to all body parts. The muscle–tendon complexes were modeled by truss elements with Hill-type muscle material and seat belt elements with tension-only material. The THUMS was validated against 35 series of cadaver or volunteer test data on frontal, lateral, and rear impacts. Model validations for 15 series of cadaver test data associated with frontal impacts are presented in this article. The THUMS with a vehicle sled model was applied to investigate effects of muscle activations on occupant kinematics and injury outcomes in specific frontal impact situations with AEB.

Results and Conclusions: In the validations using 5 series of cadaver test data, force–time curves predicted by the THUMS were quantitatively evaluated using correlation and analysis (CORA), which showed good or acceptable agreement with cadaver test data in most cases. The investigation of muscular effects showed that muscle activation levels and timing had significant effects on occupant kinematics and injury outcomes. Although further studies on accident injury reconstruction are needed, the THUMS has the potential for predictions of occupant kinematics and injury outcomes considering muscular tone effects with relatively low computational costs.     

Assessing the safety criticality of driver behavior toward cyclists at intersections

Abstract

Objective: Detailed analyses of car-to-cyclist accidents show that drivers intending to turn right at T-junctions collide more often with cyclists crossing from the right side on the bicycle lane than drivers intending to turn left. This fact has led to numerous studies examining the behavior of drivers turning left and right. However, the most essential question still has not been sufficiently answered: is the behavior of drivers intending to turn right generally more safety critical than the behavior of those intending to turn left? The purpose of this article is to provide a method that allows to determine whether a driver’s behavior toward cyclists can retrospectively be assessed as critical or non-critical.

Methods: Several theoretical considerations enriched by findings of experimental studies were employed to devise a multi-measure method. This method was applied to a dataset containing real-world approaching behavior of 48 drivers turning right and left at four T-junctions with different sight obstructions. For each driver a behavior-specific criticality was defined based on both, their driving and gaze behavior. Moreover, based on the behavior-specific criticality of each driver, the required field of view to see a cyclist from the right was defined and was set into relation with the available field of view of the T-junction.

Results: The results show that only a small portion of the drivers within the dataset would have posed an actual risk to cyclists crossing from the right side. Those situations with a higher safety criticality did not only arise when drivers intended to turn right, but also left.

Conclusion: Therefore, the analysis can only provide an explanation for the higher proportion of accidents between drivers turning right and cyclists crossing from the right side in certain situations. Further research, for example analyses of exposure data regarding the frequency of turning manoeuvers at T-junctions, is needed in order to explain the higher proportion of accidents between drivers turning right and cyclists crossing from the right side.     

Impact of perceptual countermeasures on driving behavior at curves using driving simulator

Objective: The probability of crash occurrence on horizontal curves is 1.5 to 4 times higher than that on tangent sections. A majority of these crashes are associated with human errors. Therefore, human behavior in curves needs to be corrected.

Methodology: In this study, 2 different road marking treatments, optical circles and herringbone patterns, were used to influence driver behavior while entering a curve on a 2-lane rural road section. A driving simulator was used to perform the experiment. The simulated road sections are replicas of 2 real road sections in Flanders.

Results: Both treatments were found to reduce speed before entering the curve. However, speed reduction was more gradual when optical circles were used. A herringbone pattern had more influence on lateral position than optical circles by forcing drivers to maintain a safe distance from opposing traffic in the adjacent lane.

Conclusion: The study concluded that among other low-cost speed reduction methods, optical circles are effective tools to reduce speed and increase drivers’ attention. Moreover, a herringbone pattern can be used to reduce crashes on curves, mainly for head-on crashes where the main problem is inappropriate lateral position.     

The 2001 National Household Travel Survey: a look into the travel patterns of older Americans

INTRODUCTION: The main objective of this paper is to highlight travel patterns of older adults living in the United States as depicted in the 2001 National Household Travel Survey (NHTS). The NHTS is a national data collection program sponsored by the Bureau of Transportation Statistics and the Federal Highway Administration. It is the first national comprehensive household survey of both daily and long-distance travel, allowing for analysis of the full continuum of personal travel by Americans. To better understand the transportation needs of older Americans, it is useful to examine how travel patterns differ across age groups. The intent is to present basic travel characteristics of older adults (age 65+) and allow for comparisons with younger adults (ages 19-64). Travel-related characteristics of older adults in the United States: Results of the 2001 survey showed that older Americans travel extensively and rely on personal vehicles as heavily as their younger counterparts. Older Americans conduct 89% of their travel in personal vehicles. CHARACTERISTICS OF DAILY TRIPS TAKEN BY OLDER ADULTS: Older adults tend to be less mobile in that they take fewer trips, travel shorter distances, and have shorter travel times. This pattern is even more pronounced among older women. They are also more likely to suffer from self-reported medical conditions that further limit their travel. Characteristics of long-distance travel by older adults: Older men and women take long-distance trips at about the same rates and show a strong preference for using personal vehicles. And, while men and women take an equal percentage of their trips by air, older women show a strong preference for bus travel. CONCLUSIONS: Although older Americans travel extensively, they are less mobile than their younger counterparts. This pattern is more pronounced among older women and among those with self-reported medical conditions that affect their ability to travel outside their home. Older women consistently take the least number of trips per day, have the lowest driving rates, travel the shortest distances, and are more likely to report medical conditions that limit their travel. For men and women who have to give up driving, alternative means of transportation becomes a necessity. Yet, use of alternative transportation is relatively low; excluding personal vehicle and walking, all other means of transportation account for about 2% of daily travel. Further, of those with medical conditions that affect their travel, only about 12% use special transportation services such as dial-a-ride.