Sulfamethoxazole sorption by sediment fractions in comparison to pyrene and bisphenol A

The environmental behavior of antibiotics has attracted great research attention. However, their sorption mechanisms in soils/sediments are still unknown. Comparison of the sorption properties between the widely-studied hydrophobic organic contaminants (HOCs) and antibiotics may provide valuable insight to antibiotic sorption mechanisms. Thus, in this study batch experiments for pyrene (PYR), bisphenol A (BPA), and sulfamethoxazole (SMX) sorption were conducted on a sediment sample and its separated fractions. Our results showed the high sorption of PYR on black carbon and organic matter. Although high sorption of SMX was observed for both separated organic fractions (humic acids) and inorganic mineral particles, the original sediment particles showed relatively low sorption. Competitive sorption between SMX and dissolved humic acid on mineral particles was observed in this study. This competitive interaction is a unique process for antibiotic sorption in soils/sediments compared with apolar HOCs and may be one of the important factors controlling the antibiotic sorption.     

Removal of sulfamethoxazole and sulfapyridine by carbon nanotubes in fixed-bed columns

Sulfamethoxazole (SMX) and sulfapyridine (SPY), two representative sulfonamide antibiotics, have gained increasing attention because of the ecological risks these substances pose to plants, animals, and humans. This work systematically investigated the removal of SMX and SPY by carbon nanotubes (CNTs) in fixed-bed columns under a broad range of conditions including: CNT incorporation method, solution pH, bed depth, adsorbent dosage, adsorbate initial concentration, and flow rate. Fixed-bed experiments showed that pH is a key factor that affects the adsorption capacity of antibiotics to CNTs. The Bed Depth Service Time model describes well the relationship between service time and bed depth and can be used to design appropriate column parameters. During fixed-bed regeneration, small amounts of SMX (3%) and SPY (9%) were irreversibly bonded to the CNT/sand porous media, thus reducing the column capacity for subsequent reuse from 67.9 to 50.4 mg g^?1 for SMX and from 91.9 to 72.9 mg g^?1 for SPY. The reduced column capacity resulted from the decrease in available adsorption sites and resulting repulsion (i.e., blocking) of incoming antibiotics from those previously adsorbed. Findings from this study demonstrate that fixed-bed columns packed with CNTs can be efficiently used and regenerated to remove antibiotics from water.     

Gamma irradiation-induced decomposition of sulfamethoxazole in aqueous solution: the influence of additives,biological inhibitory,and degradation mechanisms

Sulfamethoxazole (SMX) was decomposed by using gamma irradiation in the presence of different additives such as NO₃ ⁻, NO₂ ⁻, Cr(VI), 2-propanol, and tert-butanol. The results demonstrated that NO₃ ⁻, NO₂ ⁻, 2-propanol, and tert-butanol inhibited SMX radiolytic removal. However, there existed a synergetic effect for radiolytic removal of the mixture containing SMX and Cr(VI). At an absorbed dose of 150 Gy, the removal percentages of SMX and Cr(VI) in the mixture were 73.5 and 84.6%, respectively, which was higher than the removal percentages of 70.6 and 4.1% for the single component of SMX and Cr(VI). This provides us an insight into treating the combined pollution in micro-polluted water. The SMX radiolytic removal followed a pseudo first-order reaction kinetic model, and the rate constant ratios of ·OH, e_aq ⁻, and H· towards SMX radiolysis were 10.4:1:2.9. In addition, 24-h bio-inhibitory to the macroalgae of SMX solution during gamma irradiation reached the maximum of 0.85 at an adsorbed dose of 100 Gy, then gradually decreased with the increasing adsorbed dose. Based on LC-MS analysis and quantum chemical calculation, the degradation intermediates were determined and concluded that SMX radiolytic removal was mainly via ·OH radical attack and direct decomposition of SMX molecule by gamma ray.

     

Changes in water-extractability of soil inorganic phosphate induced by chloride and sulfate salts

GOAL, SCOPE AND BACKGROUND: One of the principal experimental variables which effect the results of phosphorus (P) sorption studies is the ionic composition, in addition to both species and concentrations of the contacting solution. In spite of the realization that ionic species, concentrations and their compositions effect P sorption and/or desorption, most of the salt-related studies are confined to Cl- (anion) in association with different cations. While the knowledge about the comparative response of P to Cl- and SO4(2-) ions was lacking, the current study was conducted to evaluate the comparative effects of anions (in association with cations) on inorganic P release and P fractions in the soil. METHODS: The test soil was amended with livestock compost manure (OP); KH2PO4 (IPk) or Ca(H2PO4)2 (IPc) at a rate of 1ppm. Soil was subjected to one salt and nine subsequent water extractions and different P fractions were measured. Four salt types, NaCl, Na2SO4, KCl and K2SO4, were used at levels of 0.5 M. RESULTS: Irrespective of P sources, P release was substantially increased in the salt-pretreated soil as compared to the non-saline soil. Sulfate salts released more P in subsequent water extractions than Cl-. Phosphorus release decreased for salt types with Na2SO4 > NaCl > K2SO4 > KCl and for P sources with OP approximately IPk > Control (without P application) > IPc, respectively. DISCUSSION: No previous study was found to compare the results of more P release by SO4(2-) than Cl- salt. Most of the previous studies focused on anion sorption capacities, but the mechanism for their adsorption is not fully known. Most of the authors suggested that the mechanisms of SO4(2-) and PO4(3-) adsorption are similar, and that both ions compete for the same sorption sites (Kamprath et al. 1956, Couto et al. 1979, Pasricha and Fox 1993). Although adsorbed SO4(2-) does not compete strongly with PO4(3-), there is likely to be some competition for sorption between these anions which may cause comparatively more P release by SO4(2-) than Cl- salts. Higher P release by Na-saturation could be due to the release of P associated with oxide surfaces or due to dissolution of Ca-P phases (Curtin et al. 1987). CONCLUSIONS: Study clearly showed that not only cations species differ for P desorption capacity, but associated anions also play a vital role in the fate of P under saline environments. Synergetic effects exist between Na and SO4(2-) ions which enhanced the P release. This study has also confirmed the fact that P from organic sources is available as well as from inorganic P sources. However, P release depends more on the type of P source applied than on total P. RECOMMENDATIONS AND PERSPECTIVES: It is highly recommended that more than one anion species must be used in the research plans for evaluating the P response in a saline environment. The results have important implications from the point of view of research, as most of the researchers focus on different cations only for evaluating P response to salts from an environmental point of view. However, our study has made it clear that anions in association with cations differed for their effects on P release.     

Adsorption behaviours and transfer simulation of levofloxacin in silty clay

Fluoroquinolone antibiotics in soil can cause serious antibiotic pollution. Adsorption is the main factor that influences their destination and transport of antibiotics. Therefore, research on the behaviour of antibiotics once they reach the soil environment is meaningful to design appropriate measures to reduce their potential risks. This research took levofloxacin (LVFX) as the research object and used a static adsorption experiment to study the adsorption behaviour of the vadose zone of silty clay on the North China Plain. The results showed that LVFX had high retention in silty clay, with an average adsorption ratio of more than 90%. Adsorption of LVFX on silty clay reached equilibrium in 24 h with an adsorption amount of 93.5 mg/kg at an initial LVFX concentration of 10 mg/L. Acidity, cations and soil organic matter could affect the adsorption of LVFX, with adsorption variation ratio of 3.3%, 3.4% and 0.6%, respectively. In addition, numerical simulation with Hydrus-1D was utilized, and the results show that LVFX may infiltrate into underground water through silty clay after 28 days and completely penetrate in 100 days.

     

The non-target organism Caenorhabditis elegans withstands the impact of sulfamethoxazole

The widespread usage of antibiotics in agriculture leads to releases into the environment, but there is insufficient knowledge of the side-effects on non-target organisms. Therefore, we investigated the effects of the sulfonamide-antibiotic sulfamethoxazole (SMX) on Caenorhabditis elegans at phenotypic, biochemical and molecular biological levels. Multiple endpoints, including life history traits, thermal stress resistance and lipid peroxidation, as well as gene expression profiles, were determined after exposure of the nematodes to SMX. In contrast to expectations, SMX prolonged the lifespan and increased both the body size and pharynx pumping rate. On the other hand, SMX delayed reproductive timing and caused lipid peroxidation. The total number of offspring and thermal stress resistance were unaffected. The up-regulation of hsp-16.1 indicated stress in general and the increased lipid peroxidation oxidative stress in particular. This oxidative stress indicated that mitohormesis was the likely cause of the longevity and that enhanced pumping frequency was probably the reason for the increased growth. The sole adverse effect was delayed initial reproduction. This delay, however, can be crucial for r-strategists, such as the bacterivorous model animal used, in sustaining their populations in the environment in the presence of predators. Bacterivorous animals, in turn, are essential to maintaining nutrient recycling via the microbial loop.     

SMX degradation by ozonation and UV radiation: a kinetic study

The rate constants of sulfamethoxazole (SMX) degradation by ozonation and UV₂₅₄ radiation were investigated under various parameters including influent ozone gas concentration, initial SMX concentration, UV light intensity, ionic strength, water quality in terms of varying anions (bicarbonate, sulfate and nitrate), humic acid (HA) and pH. The results indicated that the removal of SMX by ozonation and UV₂₅₄ radiation fitted well to a pseudo first-order kinetic model and the rate constants were in the range of (0.9-9.8) × 10⁻³ and (1.7-18.9) × 10⁻³ s⁻¹, respectively. The second-order rate constants of SMX with ozone (k_O3), under varying operational parameters, were also determined and varied in the range of (0.60-3.38) ± 0.13 × 10⁵ M⁻¹ s⁻¹. In addition, SMX degradation through UV pretreatment followed by ozonation in the presence of HA was proved to be an effective method which can remove SMX with a low ozone dose. The results suggested that ozonation of SMX was more affected by concentration of influent ozone gas, alkalinity, and HA, while incident UV light intensity, pH, and HA were the dominant factors influencing UV degradation of SMX.     

Cadmium (Cd2+) removal by nano zerovalent iron: surface analysis, effects of solution chemistry and surface complexation modeling

Nano zerovalent iron (nZVI) is an effective remediant for removing various organic and inorganic pollutants from contaminated water sources. Batch experiments were conducted to characterize the nZVI surface and to investigate the effects of various solution properties such as pH, initial cadmium concentration, sorbent dosage, ionic strength, and competitive ions on cadmium removal by nZVI. Energy-dispersive X-ray and X-ray photoelectron spectroscopy results confirmed removal of Cd²⁺ ions by nZVI through adsorption. Cd²⁺ adsorption decreased in the presence of competitive cations in the order: Zn²⁺?>?Co²⁺?>?Mg²⁺?>?Mn²⁺?=?Cu²⁺?>?Ca²⁺?>?Na²⁺?=?K⁺. Higher concentrations of Cl^? significantly decreased the adsorption. Cadmium removal increased with solution pH and reached a maximum at pH 8.0. The effects of various solution properties indicated Cd²⁺ adsorption on nZVI to be a chemisorption (inner-sphere complexation) process. The three surface complexation models (diffuse layer model, constant capacitance model, and triple layer model) fitted well to the adsorption edge experimental data indicating the formation of nZVI–Cd bidentate inner-sphere surface complexes. Our results suggest that nZVI can be effectively used for the removal of cadmium from contaminated water sources with varying chemical conditions.     

Dissipation of sulfamethoxazole and trimethoprim antibiotics from manure-amended soils

In this study, the dissipation of two antibiotics, sulfamethoxazole (SMX) and trimethoprim (TRM), in three soils under both aerobic and anaerobic conditions are evaluated. Under aerobic conditions, SMX dissipated rapidly through biodegradation but TRM was more persistent. Within the first 20 days in biologically active soils, >50% of the SMX was lost from the clay loam and loamy sand soils, and >80% loss was noted in the loam soil. Anaerobic dissipation of both compounds was more rapid than aerobic dissipation. The addition of manure to the soil only slightly increased the initial dissipation rate of the two compounds. Little effect was found on glucose mineralisation in soil following the addition of SMX and TRM, even as mixtures at high concentrations.     

Dissipation of sulfamethoxazole and trimethoprim antibiotics from manure-amended soils

In this study, the dissipation of two antibiotics, sulfamethoxazole (SMX) and trimethoprim (TRM), in three soils under both aerobic and anaerobic conditions are evaluated. Under aerobic conditions, SMX dissipated rapidly through biodegradation but TRM was more persistent. Within the first 20 days in biologically active soils, >50% of the SMX was lost from the clay loam and loamy sand soils, and >80% loss was noted in the loam soil. Anaerobic dissipation of both compounds was more rapid than aerobic dissipation. The addition of manure to the soil only slightly increased the initial dissipation rate of the two compounds. Little effect was found on glucose mineralisation in soil following the addition of SMX and TRM, even as mixtures at high concentrations.     

天然沸石吸附氨氮的影响因素

对比研究了沸石对生活污水和人工配制氯化铵溶液中氨氮的吸附特性,考察了沸石投加量、反应时间、悬浮物、阳离子和阴离子对沸石吸附氨氮的影响。结果表明,沸石对生活污水中氨氮的吸附能力明显低于人工配制氯化铵溶液,氨氮去除率随着沸石投加量的增加而增加,但单位质量沸石的氨氮吸附量却随之减小,吸附过程呈现快速吸附,缓慢平衡的特点。生活污水中悬浮物的存在,会削减沸石对氨氮的吸附能力。不同类型的阳离子和阴离子的加入都能导致人工配制氯化铵溶液中氨氮在沸石上的吸附量存在差异。阳离子的影响趋势主要为价态的影响,即价态越高,对氨氮吸附阻碍作用越显著,当阳离子当量浓度〉2meq／L时,影响吸附强弱的顺序为Ca2＋〉Mg2＋ 〉Na＋;阴离子影响沸石吸附强弱的顺序受初始氨氮的浓度影响较大。Langmuir等温方程式较Freundich、DubininRadushkevich、KobleCorrigan和Temkin等温方程式更好地描述沸石吸附氨氮的行为。     

Enhanced removal of tetracycline via advanced oxidation of sodium persulfate and biochar adsorption

Advanced oxidation of antibiotic tetracycline (TC) is becoming an accessible and efficient technology. The removal of TC from the complex wastewater needs to be lucubrated. In this study, a TC removal system involving degradation and adsorption was established. TC degradation was accomplished by enhanced advanced oxidation via the addition of sodium persulfate (SP) and biochar into simulated wastewater containing Mn²⁺ and TC wastewater. The adsorption of TC and its derivatives was removed by biochar. The results indicate that the optimized reaction parameters were 3.0 g/L of biochar prepared at 600 °C (B600) and 400 mg/L of SP under acidic condition, and the removal percentage of TC was 87.48%, including 74.23% of degradation and 13.28% of adsorption; the anions Cl^?, NO₃^?, and H₂PO₄^? had negligible effects on the removal of TC in this Mn²⁺/B600/SP system. The system also functioned well with an aqueous solution with a high chemical oxygen demand (COD) concentration. Electron paramagnetic resonance (EPR) analysis indicated that ·OH and SO₄^? free radicals were present in the Mn²⁺/B600/SP system. Based on the testing and analysis results, a removal mechanism and potential TC degradation pathway for this system were proposed. TC can be degraded by ·OH and SO₄^? via three degradation pathways. Mn²⁺ can be precipitated as MnO₂, and a part of the TC and its derivatives can be adsorbed on the biochar surface. The Mn²⁺/B600/SP system also performed satisfactorily for a complex aqueous solution with various cations and antibiotics.

     

Risk assessment of antibiotic residues in different water matrices in India: key issues and challenges

Global detection of antibiotic substances in water matrices has considerably increased in the recent past. However, in India research on this issue is limited or generalised in the literature. Risks associated with the presence of antibiotics in the environment can be quantified using a hazard quotient (HQ) approach. Here, HQs were developed using the measured environmental concentration (MEC) approach for antibiotic residues in Indian water matrices previously reported in the literature. In the present study, environmental risk assessment, using the HQ index [HQ?=?measured environmental concentration (MEC)/predicted no effect concentration (PNEC)] for different antibiotics, was performed according to the guidelines of European Medicine Evaluation Agency (EMEA). MEC and PNEC levels were obtained from the literature. PNEC values were also calculated from EC₅₀ using a safety factor when no PNECs were reported in the literature. HQs were obtained for industrial effluents (HQ?=?10⁴) that were greater than any previously reported values. Ciprofloxacin, a fluoroquinolone antibiotic, seemed to present the greatest risk in India. The HQ indices for Indian water matrices were in the following order: industrial effluents?>?lake water?>?river water?>?hospital effluents?>?treated sewage ? groundwater. A very high HQ represents a potential environmental concern for aquatic environments in India and demands that immediate attention be devoted to regulating these compounds, especially in pharmaceutical industrial wastewater.     

一种新型复合除砷材料的制备及其性能

将锆的水合氧化物固载于大孔螯合树脂D401上制备出一种新型除砷材料,并研究了不同实验条件下复合吸附剂D401-Zr对水溶液中As(V)的吸附性能。研究结果表明,在pH<5.2时D401-Zr对As(V)都具有较强的吸附性能;其吸附等温线与Langmuir吸附模型具有较高的吻合度;吸附动力学研究表明,D401-Zr对砷的吸附均遵循二级动力学方程;竞争吸附实验表明,与SO24-、Cl-共存时,D401-Zr对砷的去除率大于90%,而与PO34-、F-竞争离子共存时,其去除率明显下降。     

不同老化条件对聚酰胺6微塑料吸附磺胺噻唑的影响

聚酰胺类微塑料(PA-MPs)和磺胺类抗生素(SAs)均为新兴污染物且已广泛检出,其中聚酰胺6微塑料由常用的聚酰胺6塑料产生,磺胺噻唑(ST)是典型的SAs.由于微塑料在环境暴露中普遍易老化,因此探究了聚酰胺6微塑料在未老化、紫外老化、紫外和H2 O2老化(分别记为PA6、PA6-UV、PA6-UV+H2 O2)下对S...     

核桃壳粉对水溶液中Pb2＋的吸附

实验通过间歇吸附方式研究了核桃壳粉对水溶液中Pb^2＋的吸附特性,探讨了核桃壳粉粒径及用量、溶液pH、Pb^2＋初始浓度等参数对吸附的影响,并讨论了吸附过程的热力学和动力学特征。结果表明,核桃壳粉对Pb^2＋吸附的最佳pH为5．0,去除率随吸附剂粒径的减小、用量的增加、Pb^2＋初始浓度的减小而增加。优化实验条件下,0～0．3mm15g／L的吸附剂在298K时,对pH=5的50mL50mg／LPb^2＋溶液的去除率达96．98％。核桃壳粉对Pb^2＋的吸附等温线符合Sips模型,在283、293和303K的最大吸附量分别为18．25、18．27和20．94mg／g。吸附过程是放热的、混乱度减小的自发过程,且符合准二级动力学模型。吸附速率常数随温度升高而减小,在293和303K时分别在90和120min基本达到平衡。结合FTIR和SEM手段发现核桃壳对Pb^2＋的吸附以物理吸附为主,同时包括离子交换、螯合等化学吸附以及颗粒内扩散步骤,是一个复杂的过程。     

Preparation and characterization of surfactant-modified hydroxyapatite/zeolite composite and its adsorption behavior toward humic acid and copper(II)

A novel composite material, i.e., surfactant-modified hydroxyapatite/zeolite composite, was used as an adsorbent to remove humic acid (HA) and copper(II) from aqueous solution. Hydroxyapatite/zeolite composite (HZC) and surfactant-modified HZC (SMHZC) were prepared and characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and field emission scanning electron microscope. The adsorption of HA and copper(II) on SMHZC was investigated. For comparison purposes, HA adsorption onto HZC was also investigated. SMHZC exhibited much higher HA adsorption capacity than HZC. The HA adsorption capacity for SMHZC decreased slightly with increasing pH from 3 to 8 but decreased significantly with increasing pH from 8 to 12. The copper(II) adsorption capacity for SMHZC increased with increasing pH from 3 to 6.5. The adsorption kinetic data of HA and copper(II) on SMHZC obeyed a pseudo-second-order kinetic model. The adsorption of HA and copper(II) on SMHZC took place in three different stages: fast external surface adsorption, gradual adsorption controlled by both film and intra-particle diffusions, and final equilibrium stage. The equilibrium adsorption data of HA on SMHZC better fitted to the Langmuir isotherm model than the Freundlich isotherm model. The equilibrium adsorption data of copper(II) on SMHZC could be described by the Langmuir, Freundlich, and Dubinin–Radushkevich isotherm models. The presence of copper(II) in solution enhanced HA adsorption onto SMHZC. The presence of HA in solution enhanced copper(II) adsorption onto SMHZC. The mechanisms for the adsorption of HA on SMHZC at pH 7 may include electrostatic attraction, organic partitioning, hydrogen bonding, and Lewis acid–base interaction. The mechanisms for the adsorption of copper(II) on SMHZC at pH 6 may include surface complexation, ion exchange, and dissolution–precipitation. The obtained results indicate that SMHZC can be used as an effective adsorbent to simultaneously remove HA and copper(II) from water.     

Cosorption of organic chemicals with different properties: their shared and different sorption sites

Complementary sorption of different chemicals was expected and investigating the relationship between the sorption inhibition of primary sorbate (ΔQ(pri)) and sorption of secondary sorbate (Q(sec)) could provide a new angle to understand coadsorption of different chemicals. This study used bisphenol A (BPA) as the primary adsorbate, sulfamethoxazole (SMX) as the competitor, and carbon nanotubes as model adsorbents to study their complementary and competitive adsorption. At low BPA concentrations, the sorption of SMX (Q(sec)) exceeded BPA sorption inhibition (ΔQ(pri)), indicating that these two chemicals complementarily adsorbed on their respectively preferred sorption sites. At high BPA concentrations, higher ΔQ(pri) was observed in comparison to Q(sec), which may be resulted from different packing efficiencies of the adsorbed SMX and BPA. This study emphasized that both competitive and complementary sorption should be discussed in binary sorption system.     

Thermodynamic analysis of fatty acid harvesting by novel carbon-based adsorbent

In this study, separation and concentration of fatty acids (FA) from the synthetic food processing wastewater containing low concentration of FA (250 mg/L) were investigated using expanded graphite (EG) as a novel adsorbent at different temperatures (298~318 K). The adsorption results were further analyzed to verify adsorption mechanisms and thermodynamics of FA onto EG. Results show that the adsorption of FA onto EG was explained well by the Langmuir model with the maximum adsorption capacity up to 8.01 g FA/g EG at 298 K, and considerably affected by temperature. The adsorption kinetics fitted with pseudo-second-order kinetic model and the adsorption mechanism analysis showed that the intraparticle diffusion was not the rate-limiting step, but the coalescence of FA droplets played the significant role for novel adsorption of FA onto EG. The calculated activation energy and thermodynamic parameters such as Gibbs free energy change (ΔG⁰), enthalpy change (ΔH⁰), and entropy change (ΔS⁰) indicated that the adsorption of FA onto EG was very feasible, was highly spontaneous, occurred physically, was exothermic in nature, and was stable in aquatic environmental changes. Overall, FA can be effectively harvested and concentrated from the food processing wastewater by EG even at low concentration.     

Biosolid-borne tetracyclines and sulfonamides in plants

Tetracyclines and sulfonamides used in human and animal medicine are released to terrestrial ecosystems from wastewater treatment plants or by direct manure application. The interactions between plants and these antibiotics are numerous and complex, including uptake and accumulation, phytometabolism, toxicity responses, and degradation in the rhizosphere. Uptake and accumulation of antibiotics have been studied in plants such as wheat, maize, potato, vegetables, and ornamentals. Once accumulated in plant tissue, organic contaminants can be metabolized through a sequential process of transformation, conjugation through glycosylation and glutathione pathways, and ultimately sequestration into plant tissue. While studies have yet to fully elucidate the phytometabolism of tetracyclines and sulfonamides, an in-depth review of plant and mammalian studies suggest multiple potential transformation and conjugation pathways for tetracyclines and sulfonamides. The presence of contaminants in the vicinity or within the plants can elicit stress responses and defense mechanisms that can help tolerate the negative effects of contaminants. Antibiotics can change microbial communities and enzyme activity in the rhizosphere, potentially inducing microbial antibiotic resistance. On the other hand, the interaction of microbes and root exudates on pharmaceuticals in the rhizosphere can result in degradation of the parent molecule to less toxic compounds. To fully characterize the environmental impacts of increased antibiotic use in human medicine and animal production, further research is essential to understand the effects of different antibiotics on plant physiology and productivity, uptake, translocation, and phytometabolism of antibiotics, and the role of antibiotics in the rhizosphere.