A two-region nonequilibrium model for solute transport in solution conduits in karstic aquifers

A two-region nonequilibrium model was used to calibrate initial solute-transport parameter estimates generated from tracer-breakthrough curves (TBCs) developed from tracer tests conducted in uni-axial solution conduits in karstic aquifers. Two-region nonequilibrium models account for partitioning of solute into mobile- and immobile-fluid regions to produce a more representative model fit to the strong tails associated with TBCs than do equilibrium models. The nonequilibrium model resulted in an increase in average flow velocities and a decrease in longitudinal dispersion coefficients over comparable estimates using an equilibrium model. Increases in velocity and decreases in dispersion were obtained at the expense of including parameters that describe solute partitioning and mass transfer rate for the mobile- and immobile-fluid regions. In addition, nonidentifiable sorption and mass transfer parameters for the immobile-fluid regions could only be described in terms of upper and lower bounds using readily determined identifiable ratios representing solute partitioning and system constraints based on known physical properties. The identifiable ratios and system constraints serve to minimize model nonuniqueness and renders the nonidentification problem trivial.     

Nonequilibrium transport of organic chemicals: The impact of pore-water velocity

The impact of variations in pore-water velocity on the nonequilibrium sorption and transport of organic chemicals was investigated. Miscible displacement experiments were performed with four organic chemicals (dichlorobenzene, naphthalene, tetrachloroethene and p-xylene) and three aquifer materials having low organic-carbon contents (0.02–0.1%). The results of the experiments were analyzed by using a one-dimensional advective-dispersive transport model, wherein sorption is considered instantaneous for a fraction of the sorbent and rate-limited for the remainder. An inverse relationship between the reverse sorption rate constant and the equilibrium sorption constant was evident for each of two velocities. However, there was an order-of-magnitude difference between the rate constants obtained at the two velocities. This suggests the existence of a time-scale effect, which must be accounted for when modeling the transport of organic solutes.     

Prediction of mass-transfer coefficient for solute transport in porous media

Several previously reported laboratory studies related to transport of solutes through packed columns were utilized to develop predictive relationships for mass-transfer rate coefficient. The data were classified into two groups: those obtained under rate-limited mass transfer between mobile and immobile water regions (physical nonequilibrium conditions), and those derived from rate-limited mass transfer between instantaneous and slow sorption sites (sorption nonequilibrium conditions). The mass-transfer coefficient in all these studies was obtained by fitting breakthrough data to a transport model employing a first-order rate limitations with a "constant" mass-transfer coefficient, independent of flow conditions. This study demonstrated that the mass-transfer coefficient in these models is dependent on system parameters including pore-water velocity, length-scale, retardation coefficient, and particle or aggregate size. Predictive relationships were developed, through regression analysis, relating mass-transfer coefficient to residence time. The developed relationships adequately estimated previously reported field mass-transfer values. Successful simulations of field desorption data reported by Bahr [J. Contam. Hydrol. 4 (1989) 205] further demonstrate the potential applicability of the developed relationships.     

Comparison of nonideal sorption formulations in modeling the transport of phthalate esters through packed soil columns

Sorption of dimethyl phthalate (DMP), diethyl phthalate (DEP) and dipropyl phthalate (DPP) to two soil materials that vary in organic matter content was investigated using miscible displacement experiments under saturated flow conditions. Generated breakthrough curves (BTCs) were inversely simulated using linear, equilibrium sorption (LE), nonlinear, equilibrium sorption (NL), linear, first-order nonequilibrium sorption (LFO), linear, radial diffusion (LRD), and nonlinear, first-order nonequilibrium sorption (NFO) models. The Akaike information criterion was utilized to determine the preferred model. The LE model could not adequately describe phthalate ester (PE) BTCs in higher organic matter soil or for more hydrophobic PEs. The LFO and LRD models adequately described the BTCs but a slight improvement in curve-fitting was gained in some cases when the NFO model was used. However, none of the models could properly describe the desorptive tail of DPP for the high organic matter soil. Transport of DPP through this soil was adequately predicted when degradation or sorption hysteresis was considered. Using the optimized parameter values along with values reported by others it was shown that the organic carbon distribution coefficient (K(oc)) of PEs correlates well with the octanol/water partition coefficient (K(ow)). Also, a strong relationship was found between the first-order sorption rate coefficient normalized to injection pulse size and compound residence time. A similar trend of timescale dependence was found for the rate parameter in the radial diffusion model. Results also revealed that the fraction of instantaneous sorption sites is dependent on K(ow) and appears to decrease with the increase in the sorption rate parameter.     

Sorption of hydrophobic organic pollutants in saturated soil systems

Sorption equilibria and rates were characterized for a matrix of four aquifer sands and two slightly to moderately hydrophobic organic solutes (nitrobenzene and lindane), and the effects of sorption on the behavior of these solutes in saturated systems of the soils were determined. Experimental data were used to test and evaluate a variety of mathematical models for predicting contaminant fate and transport in groundwater systems.Observed equilibrium relationships between soil and solution phase solute concentrations were found to be described best by the nonlinear Freundlich isotherm model. It was further determined that the sorption process in the systems tested is rate controlled, requiring several days to approach equilibrium in completely mixed batch reactors. Subsequent modeling of solute transport in continuous flow soil column reactors was found to be most successful when rate-controlled models were used, the best results were obtained with a dual-resistance model incorporating the coupled mass transport steps of boundary-layer and intraparticle diffusion.     

Description of sorbing tracers transport in fractured media using the lattice model approach

The transport of contaminants in fractured media is a complex phenomenon with a great environmental impact. It has been described with several models, most of them based on complex partial differential equations, that are difficult to apply when equilibrium and nonequilibrium dynamics are considered in complex boundaries. With the aim of overcoming this limitation, a combination of two lattice Bathnagar, Gross and Krook (BGK) models, derived from the lattice Boltzmann model, is proposed in this paper. The fractured medium is assumed to be a single fissure in a porous rock matrix. The proposed approach permits us to deal with two processes with different length scales: advection-dispersion in the fissure and diffusion within the rock matrix. In addition to the mentioned phenomena, sorption reactions are also considered. The combined model has been tested using the experimental breakthrough curves obtained by Garnier et al. (Garnier, J.M., Crampon, N., Préaux, C., Porel, G., Vreulx, M., 1985. Tra?age par 13C, 2H, I- et uranine dans la nappe de la craie sénonienne en écoulement radial convergent (Béthune, France). J. Hidrol. 78, 379-392.) giving acceptable results. A study on the influence of the lattice BGK models parameters controlling sorption and matrix diffusion on the breakthrough curves shape is included.     

Nonequilibrium sorption of phenols onto geosorbents: the impact of pH on intraparticle mass transfer

While the pH effect on sorption equilibrium of weak acids on natural sorbents was investigated in a number of studies, less is known about the pH dependence of sorption kinetics. This paper investigates the impact of pH on sorption kinetics during the transport of some selected phenols through a sandy aquifer material. Breakthrough curves measured in column experiments were analyzed using a mass transfer based nonequilibrium model designated as dispersed flow, film and particle diffusion model (DF-FPDM). In this model, the rate limiting intraparticle diffusion is characterized by the mass transfer coefficient, kSaV, which can be determined from breakthrough curves by curve fitting. The experimental results indicate that the kSaV is pH-dependent and inversely correlated with the pH-dependent distribution coefficient, K(d,app). Regression equations are presented that may be used to estimate approximate values of intraparticle mass transfer coefficients on the basis of experimentally determined or LFER predicted distribution coefficients.     

Description of sorbing tracers transport in fractured media using the lattice model approach

The transport of contaminants in fractured media is a complex phenomenon with a great environmental impact. It has been described with several models, most of them based on complex partial differential equations, that are difficult to apply when equilibrium and nonequilibrium dynamics are considered in complex boundaries. With the aim of overcoming this limitation, a combination of two lattice Bathnagar, Gross and Krook (BGK) models, derived from the lattice Boltzmann model, is proposed in this paper. The fractured medium is assumed to be a single fissure in a porous rock matrix. The proposed approach permits us to deal with two processes with different length scales: advection–dispersion in the fissure and diffusion within the rock matrix. In addition to the mentioned phenomena, sorption reactions are also considered. The combined model has been tested using the experimental breakthrough curves obtained by Garnier et al. (Garnier, J.M., Crampon, N., Préaux, C., Porel, G., Vreulx, M., 1985. Traçage par ¹³C, ²H, I⁻ et uranine dans la nappe de la craie sénonienne en écoulement radial convergent (Béthune, France). J. Hidrol. 78, 379–392.) giving acceptable results. A study on the influence of the lattice BGK models parameters controlling sorption and matrix diffusion on the breakthrough curves shape is included.     

Modelling the solute transport under nonequilibrium conditions on the basis of mass transfer equations

A solute transport model that describes nonequilibrium adsorption in soil/groundwater systems by mass transfer equations for film and intraparticle diffusion is presented. The model is useful in cases where breakthrough curve spreading cannot be explained by dispersion only. To evaluate its validity, the model was applied to several data sets from column experiments. The validity was also proved by a comparison with an analytical solution for the limiting case of predominating dispersion. Furthermore, a sensitivity analysis was performed to illustrate the influence of different process and sorption parameters (pore water velocity, intraparticle mass transfer coefficient, isotherm nonlinearity) on the shape of the calculated breakthrough curves. The application of the proposed model is discussed in comparison to the widely used dispersed flow/local equilibrium model, and a relationship between both models, which is based on a lumped parameter approach, is shown.     

Dual-domain solute transfer and transport processes: evaluation in batch and transport experiments

Soil macropore networks establish a dual-domain transport scenario in which water and solutes are preferentially channeled through soil macropores while slowly diffusing into and out of the bulk soil matrix. The influence of macropore networks on intra-ped solute diffusion and preferential transport in a soil typical of subsurface-drained croplands in the Midwestern United States was studied in batch- and column-scale experiments. In the batch diffusion studies with soil aggregates, the estimated diffusion radius (length) of the soil aggregates corresponded to the half-spacing of the aggregate fissures, suggesting that the intra-ped fissures reduced the diffusion impedance and preferentially allowed solutes to diffuse into the soil matrix. In the column-scale solute transport experiments, the average diffusion radius (estimated from HYDRUS-2D simulations and a first-order diffusive transfer term) was nearly double that of the batch-scale study. This increase may be attributed to a loss of pore continuity and a compounding of the small diffusion impedance through macropores at the larger scale. The column-scale solute transport experiments also suggest that two preferential networks exist in the soil. At and near soil saturation, a primary network of large macropores (possibly root channels and earthworm burrows) dominate advective transport, causing a high degree of physical and sorption nonequilibrium and simultaneous breakthrough of a nonreactive (bromide) and a reactive (alachlor) solute. As the saturation level decreases, the primary network drains, while transport through smaller macropores (possibly intra-ped features) continues, resulting in a reduced degree of nonequilibrium and separation in the breakthrough curves of bromide and alachlor.     

Continuous time random walk model better describes the tailing of atrazine transport in soil

Contaminant transport in soils is complicated and involves some physical and chemical nonequilibrium processes. In this research, the soil column displacement experiments of Cl⁻ and atrazine under different flow velocities were carried out. The data sets of Cl⁻ transport in sandy loam fitted to the convection dispersion equation (CDE) and the two-region model (TRM) indicated that the effects of physical nonequilibrium process produced by immobile water on the breakthrough curves (BTCs) of Cl⁻ and atrazine transport through the repacking soil columns were negligible. The two-site model (TSM) and the continuous time random walk (CTRW) were also used to fit atrazine transport behavior at the flow rate of 19.86 cm h⁻¹. The CTRW convincingly captured the full evolution of atrazine BTC in the soil column, especially for the part of long tailing. However, the TSM failed to characterize the tailing of atrazine BTC in the soil column. The calculated fraction of equilibrium sorption sites, F, ranging from 0.78 to 0.80 for all flow rates suggested the contribution of nonequilibrium sorption sites to the asymmetry of atrazine BTCs. Furthermore, the data sets for the flow rates of 6.68 cm h⁻¹ and 32.81 cm h⁻¹ were predicted by the TSM and the CTRW. As to the flow rate of 6.68 cm h⁻¹, the CTRW predicted the entire BTC of atrazine transport better than the TSM did. For the flow rate of 32.81 cm h⁻¹, the CTRW characterized the late part of the tail better, while the TSM failed to predict the tailings of atrazine BTC.     

Application of the method of temporal moments to interpret solute transport with sorption and degradation

In this note, we applied the temporal moment solutions of [Das and Kluitenberg, 1996. Soil Sci. Am. J. 60, 1724] for one-dimensional advective-dispersive solute transport with linear equilibrium sorption and first-order degradation for time pulse sources to analyse soil column experimental data. Unlike most other moment solutions, these solutions consider the interplay of degradation and sorption. This permits estimation of a first-order degradation rate constant using the zeroth moment of column breakthrough data, as well as estimation of the retardation factor or sorption distribution coefficient of a degrading solute using the first moment. The method of temporal moment (MOM) formulae was applied to analyse breakthrough data from a laboratory column study of atrazine, hexazinone and rhodamine WT transport in volcanic pumice sand, as well as experimental data from the literature. Transport and degradation parameters obtained using the MOM were compared to parameters obtained by fitting breakthrough data from an advective-dispersive transport model with equilibrium sorption and first-order degradation, using the nonlinear least-square curve-fitting program CXTFIT. The results derived from using the literature data were also compared with estimates reported in the literature using different equilibrium models. The good agreement suggests that the MOM could provide an additional useful means of parameter estimation for transport involving equilibrium sorption and first-order degradation. We found that the MOM fitted breakthrough curves with tailing better than curve fitting. However, the MOM analysis requires complete breakthrough curves and relatively frequent data collection to ensure the accuracy of the moments obtained from the breakthrough data.     

Sorption and desorption by ideal two-compartment systems: unusual behavior and data interpretation problems

This paper examines the current practices of fitting curves to sorption, desorption, and equilibrium data obtained from laboratory experiments. Systems of equations incorporating Freundlich isotherms and first-order kinetics for two different idealized sorbents, one "fast" and one "slow," were solved numerically to produce "data". Two-compartment curves were then fit to the data by nonlinear regression, and the parameters computed by the regression are compared with the original parameters used to produce the data. The results show that a sorbent with fast kinetics will not steadily accumulate sorbate until it reaches the equilibrium value but will overshoot equilibrium, accumulating an excess of sorbate. This overshoot will cause the sorption rates for both sorbents and the distribution between the fast and slow sorbents to be estimated incorrectly. The system may appear to be at equilibrium by external measures, but sorbate will slowly be redistributing from the fast to the slow sorbent. An isotherm constructed from data acquired during this process will have an incorrect coefficient and exponent. Consequently, the meaning of the results obtained by curve fitting may often be questionable and may say little about the phenomena occurring within the sorbate-sorbent-liquid system. Possible physical explanations for the effects observed are offered.     

Cesium migration in saturated silica sand and Hanford sediments as impacted by ionic strength

Large amounts of 137Cs have been accidentally released to the subsurface from the Hanford nuclear site in the state of Washington, USA. The cesium-containing liquids varied in ionic strengths, and often had high electrolyte contents, mainly in the form of NaNO3 and NaOH, reaching concentrations up to several moles per liter. In this study, we investigated the effect of ionic strengths on Cs migration through two types of porous media: silica sand and Hanford sediments. Cesium sorption and transport was studied in 1, 10, 100, and 1000 mM NaCl electrolyte solutions at pH 10. Sorption isotherms were constructed from batch equilibrium experiments and the batch-derived sorption parameters were compared with column breakthrough curves. Column transport experiments were analyzed with a two-site equilibrium-nonequilibrium model. Cesium sorption to the silica sand in batch experiments showed a linear sorption isotherm for all ionic strengths, which matched well with the results from the column experiments at 100 and 1000 mM ionic strength; however, the column experiments at 1 and 10 mM ionic strength indicated a nonlinear sorption behavior of Cs to the silica sand. Transport through silica sand occurred under one-site sorption and equilibrium conditions. Cesium sorption to Hanford sediments in both batch and column experiments was best described with a nonlinear Freundlich isotherm. The column experiments indicated that Cs transport in Hanford sediments occurred under two-site equilibrium and nonequilibrium sorption. The effect of ionic strength on Cs transport was much more pronounced in Hanford sediments than in silica sands. Effective retardation factors of Cs during transport through Hanford sediments were reduced by a factor of 10 when the ionic strength increased from 100 to 1000 mM; for silica sand, the effective retardation was reduced by a factor of 10 when ionic strength increased from 1 to 1000 mM. A two order of magnitude change in ionic strength was needed in the silica sand to observe the same change in Cs retardation as in Hanford sediments.     

Evaluating equilibrium and non-equilibrium transport of bromide and isoproturon in disturbed and undisturbed soil columns

In this study, displacement experiments of isoproturon were conducted in disturbed and undisturbed columns of a silty clay loam soil under similar rainfall intensities. Solute transport occurred under saturated conditions in the undisturbed soil and under unsaturated conditions in the sieved soil because of a greater bulk density of the compacted undisturbed soil compared to the sieved soil. The objective of this work was to determine transport characteristics of isoproturon relative to bromide tracer. Triplicate column experiments were performed with sieved (structure partially destroyed to simulate conventional tillage) and undisturbed (structure preserved) soils. Bromide experimental breakthrough curves were analyzed using convective-dispersive and dual-permeability (DP) models (HYDRUS-1D). Isoproturon breakthrough curves (BTCs) were analyzed using the DP model that considered either chemical equilibrium or non-equilibrium transport. The DP model described the bromide elution curves of the sieved soil columns well, whereas it overestimated the tailing of the bromide BTCs of the undisturbed soil columns. A higher degree of physical non-equilibrium was found in the undisturbed soil, where 56% of total water was contained in the slow-flow matrix, compared to 26% in the sieved soil. Isoproturon BTCs were best described in both sieved and undisturbed soil columns using the DP model combined with the chemical non-equilibrium. Higher degradation rates were obtained in the transport experiments than in batch studies, for both soils. This was likely caused by hysteresis in sorption of isoproturon. However, it cannot be ruled out that higher degradation rates were due, at least in part, to the adopted first-order model. Results showed that for similar rainfall intensity, physical and chemical non-equilibrium were greater in the saturated undisturbed soil than in the unsaturated sieved soil. Results also suggested faster transport of isoproturon in the undisturbed soil due to higher preferential flow and lower fraction of equilibrium sorption sites.     

Multi-process herbicide transport in structured soil columns: experiments and model analysis

Model predictions of pesticide transport in structured soils are complicated by multiple processes acting concurrently. In this study, the hydraulic, physical, and chemical nonequilibrium (HNE, PNE, and CNE, respectively) processes governing herbicide transport under variably saturated flow conditions were studied. Bromide (Br-), isoproturon (IPU, 3-(4-isoprpylphenyl)-1,1-dimethylurea) and terbuthylazine (TER, N2-tert-butyl-6-chloro-N4-ethyl-1,3,5-triazine-2,4-diamine) were applied to two soil columns. An aggregated Ap soil column and a macroporous, aggregated Ah soil column were irrigated at a rate of 1 cm h(-1) for 3 h. Two more irrigations at the same rate and duration followed in weekly intervals. Nonlinear (Freundlich) equilibrium and two-site kinetic sorption parameters were determined for IPU and TER using batch experiments. The observed water flow and Br- transport were inversely simulated using mobile-immobile (MIM), dual-permeability (DPM), and combined triple-porosity (DP-MIM) numerical models implemented in HYDRUS-1D, with improving correspondence between empirical data and model results. Using the estimated HNE and PNE parameters together with batch-test derived equilibrium sorption parameters, the preferential breakthrough of the weakly adsorbed IPU in the Ah soil could be reasonably well predicted with the DPM approach, whereas leaching of the strongly adsorbed TER was predicted less well. The transport of IPU and TER through the aggregated Ap soil could be described consistently only when HNE, PNE, and CNE were simultaneously accounted for using the DPM. Inverse parameter estimation suggested that two-site kinetic sorption in inter-aggregate flow paths was reduced as compared to within aggregates, and that large values for the first-order degradation rate were an artifact caused by irreversible sorption. Overall, our results should be helpful to enhance the understanding and modeling of multi-process pesticide transport through structured soils during variably saturated water flow.     

Modelling of diffusion-limited retardation of contaminants in hydraulically and lithologically nonuniform media

A new reactive transport modelling approach and examples of its application are presented, dealing with the impact of sorption/desorption kinetics on the spreading of solutes, e.g. organic contaminants, in groundwater. Slow sorption/desorption is known from the literature to be strongly responsible for the retardation of organic contaminants. The modelling concept applied in this paper quantifies sorption/desorption kinetics by an intra-particle diffusion approach. According to this idea, solute uptake by or release from the aquifer material is modelled at small scale by a "slow" diffusion process where the diffusion coefficient is reduced as compared to the aqueous diffusion coefficient due to (i) the size and shape of intra-particle pores and (ii) retarded transport of solutes within intra-particle pores governed by a nonlinear sorption isotherm. This process-based concept has the advantage of requiring only measurable model parameters, thus avoiding fitting parameters like first-order rate coefficients.In addition, the approach presented here allows for modelling of slow sorption/desorption in lithologically nonuniform media. Therefore, it accounts for well-known experimental findings indicating that sorptive properties depend on (i) the grain size distribution of the aquifer material and (ii) the lithological composition (e.g. percentage of quartz, sandstone, limestone, etc.) of each grain size fraction. The small-scale physico-chemical model describing sorption/desorption is coupled to a large-scale model of groundwater flow and solute transport. Consequently, hydraulic heterogeneities may also be considered by the overall model. This coupling is regarded as an essential prerequisite for simulating field-scale scenarios which will be addressed by a forthcoming publication.This paper focuses on mathematical model formulation, implementation of the numerical code and lab-scale model applications highlighting the sorption and desorption behavior of an organic contaminant (Phenanthrene) with regard to three lithocomponents exhibiting different sorptive properties. In particular, it is shown that breakthrough curves (BTCs) for lithologically nonuniform media cannot be obtained via simple arithmetic averaging of breakthrough curves for lithologically uniform media. In addition, as no analytical solutions are available for model validation purposes, simulation results are compared to measurements from lab-scale column experiments. The model results indicate that the new code can be regarded as a valuable tool for predicting long-term contaminant uptake or release, which may last for several hundreds of years for some lithocomponents. In particular, breakthrough curves simulated by pure forward modelling reproduce experimental data much better than a calibrated standard first-order kinetics reactive transport model, thus indicating that the new approach is of high quality and may be advantageously used for supporting the design of remediation strategies at contaminated sites where some lithocomponents and/or grain size classes may provide a long-term pollutant source.     

Application of continuous time random walk theory to nonequilibrium transport in soil

Continuous time random walk (CTRW) formulations have been demonstrated to provide a general and effective approach that quantifies the behavior of solute transport in heterogeneous media in field, laboratory, and numerical experiments. In this paper we first apply the CTRW approach to describe the sorbing solute transport in soils under chemical (or) and physical nonequilibrium conditions by curve-fitting. Results show that the theoretical solutions are in a good agreement with the experimental measurements. In case that CTRW parameters cannot be determined directly or easily, an alternative method is then proposed for estimating such parameters independently of the breakthrough curve data to be simulated. We conduct numerical experiments with artificial data sets generated by the HYDRUS-1D model for a wide range of pore water velocities (υ) and retardation factors (R) to investigate the relationship between CTRW parameters for a sorbing solute and these two quantities (υ, R) that can be directly measured in independent experiments. A series of best-fitting regression equations are then developed from the artificial data sets, which can be easily used as an estimation or prediction model to assess the transport of sorbing solutes under steady flow conditions through soil. Several literature data sets of pesticides are used to validate these relationships. The results show reasonable performance in most cases, thus indicating that our method could provide an alternative way to effectively predict sorbing solute transport in soils. While the regression relationships presented are obtained under certain flow and sorption conditions, the methodology of our study is general and may be extended to predict solute transport in soils under different flow and sorption conditions.