Highly efficient conversion of sugarcane bagasse pretreated with liquid hot water into ethanol at high solid loading

Liquid hot water (LHW), an environmental-friendly physico-chemical treatment, was applied to pretreat the sugarcane bagasse (SCB). Tween80, a non-ionic surfactant, was used to enhance the enzymatic hydrolysis of the pretreated SCB. It found that 0.125 mL Tween80 /g dry matter could make the maximum increase (33.2%) of the glycan conversion of the LHW-pretreated SCB. A self-designed laboratory facility with a plate-and-frame impeller was applied to conduct batch hydrolysis, fed-batch hydrolysis, and the process of high-temperature (50°C) fed-batch hydrolysis following low-temperature (30°C) simultaneous saccharification and fermentation (SSF) which was adopted to overcome the incompatible optimum temperature of saccharification and fermentation in the SSF process. After hydrolyzing LHW-pretreated SCB for 120 h with commercial cellulase, the total sugar concentration and glycan conversion obtained from fed-batch hydrolysis were 91.6 g/L and 68.3%, respectively, which were 9.7 g/L and 7.3% higher than those obtained from batch hydrolysis. With Saccharomyces cerevisiae Y2034 fermenting under the non-sterile condition, the ethanol production and theoretical yield obtained from the process of SSF after fed-batch hydrolysis were 55.4 g/L and 88.3% for 72h, respectively, which were 15.5 g/L and 24.7% higher than those from separate fed-batch hydrolysis and fermentation. The result of this work was superior to the reported results obtained from the LHW-pretreated SCB.     

Optimization of activated carbon production from empty fruit bunch fibers in one-step steam pyrolysis for cadmium removal from aqueous solution

The fast growth of the palm oil industry in Malaysia is associated with various waste products, namely the empty fruit bunches (EFB), which have a negative impact on the environment. Therefore, these wastes were utilized as a cheap raw material for the production of activated carbon (AC) with less energy consumption. One-step steam pyrolysis was used to produce AC from oil palm empty fruit bunch fibers (EFBF) by varying the operating parameters of temperature, steam flow rate, and activation time using two-level full factorial experimental design (FFD). Ten samples of AC were prepared and the optimized production conditions were chosen based on the ability to adsorb and remove cadmium. Physical activation comprised of carbonization for 30 min using nitrogen gas (N₂), followed by activation with steam at different flow rates (2.0, 3.0, and 4.0 ml/min), temperatures (600, 750, and 900°C) and times (15, 30, and 45 min). The AC sample produced at an activation temperature of 900°C with a steam flow rate of 2.0 ml/min and activation time of 15 min was selected as the best adsorbent with a total yield of 21.7%. It had adsorbed more than 97% of total cadmium from aqueous solution within 2 min of the contact time. Characterization of EFBF-based AC by SEM and BET surface area analysis had shown a good-quality adsorbent with highly active sites and well-developed pores with BET surface area of 635.16 m²/g. Experimental results indicated that the prepared AC from EFBF provide a promising solution in water and wastewater treatment.     

An effective approach to improve ethanol productivity by simultaneous saccharification and fermentation of rice straw

Fuel ethanol was produced using rice straw with the simultaneous saccharification and fermentation (SSF) method. The influence of cellulose liquefaction pretreatment and Fe²⁺ quantity on ethanol productivity was investigated in detail. At the same time, the optimized conditions including fermentation temperature, Fe²⁺ amount, yeast inoculation quantity, and the inoculated cellulose enzyme dosage in the SSF process were systematically investigated by analyzing fuel ethanol yield. The result indicated that fuel ethanol yield was 0.319 g per gram rice straw by SSF approach when appropriate amount of Fe²⁺ was added into the reaction system. The optimal technology parameters were: fermenting temperature of 36°C, Fe²⁺ amount of 4 mg · g^?1, inoculating proportion of 20%, cellulose enzyme of 20 IU · g^?1, and Pachysolen tannophilu/saecharomyces cerevisiae of 1:2 ratio. The ethanol yield under the best conditions was larger than that of the control group. We hope that this research can facilitate to achieve large-scale comprehensive utilization for rice straw.     

The influence of dilute sulfuric acid pretreatment on biogas production from wheat plant

Dilute sulfuric acid pretreatment was used to improve the biomethane production from wheat plant (WP) via mesophilic anaerobic digestion. The pretreatments were performed at 121°C for different time durations of 10, 30, 60, and 120 min. The maximum methane yield of 302.4 mL/g volatile solids (VS) was obtained after the pretreatment for 120 min, which was 15.5% higher than that of the untreated WP. The highest amounts of lignin removal (15.2%) and xylan degradation (91.5%) were also achieved after this pretreatment. The pretreatment for 60 min enhanced the methane yield by 8.9%, while the pretreatments for 10 and 30 min had no positive effects on the methane yield. All of the pretreatments significantly removed the hemicelluloses. Moreover, the qualitative analysis of the untreated and pretreated WP structure showed significant reduction in the crystallinity index accompanied by the destruction of surface layers of WP structure after pretreatment.     

Ethanol production from alkali-pretreated oil palm empty fruit bunch by simultaneous saccharification and fermentation with mucor indicus

Oil palm empty fruit bunch (OPEFB) is a potential raw material for production of lignocellulosic bioethanol. The OPEFB was pretreated with 8% sodium hydroxide (NaOH) solution at 100°C for 10 to 90 min. Enzymatic digestion was carried out using cellulase and β-glucosidase at 45°C for 24 h. It was then inoculated with Mucor indicus spores suspension and fermented under anaerobic conditions at 37°C for 96 h. Sodium hydroxide pretreatment effectively removed 51–57% of lignin in the OPEFB and also its hemicellulose (40–84%). The highest glucan digestibility (0.75 g/g theoretical glucose) was achieved in 40-min NaOH pretreatment. Fermentation by M. indicus resulted in 68.4% of the theoretical ethanol yield, while glycerol (16.2–83.2 mg/g), succinic acid (0–0.4 mg/g), and acetic acid (0–0.9 mg/g) were its by-products. According to these results, 11.75 million tons of dry OPEFB in Indonesia can be converted into 1.5 billion liters of ethanol per year.     

油田化工污水中总氰化物的检测

采用在线蒸馏-流动注射分析法检测大庆油田化工污水中总氰化物。分析流速和温度对流动注射仪检测结果的影响,得出结论:载流流速为1.8mL/min,显色剂流速在1.3mL/min,缓冲溶液流速稳定在1.6mL/min时,分析精度最好;显色反应在60℃以下进行时,可以消除温度差异对检测结果的干扰。该方法适用于油田化工废水中总氰化物的检测。     

An Investigation of Thermal Decomposition Behavior of Hazelnut Shells

Turkey has a drastic potential in terms of biomass energy and it would be of utmost importance for our energy mix if this huge amount of energy is to be utilized. Thermochemical conversion is the most dominant one among the energy conversion processes. The carbonization process is the key point in determining the kinetic parameters of the fuels utilized. Thereafter, the kinetic parameters obtained from carbonization would be utilized in designing the thermochemical conversion equipments. In this study, the thermal decomposition behavior of hazelnut shells was investigated via dynamical thermogravimetry (TG) under N₂ atmosphere. In order to determine the effects of heating rate and gas flow rate, the experiments were performed in four different heating rates of 5, 20, 50, and 100 K/min and two different nitrogen flow rates of 50 and 100 cm³/min. As the heating rate was increased, peak temperature was increased, maximum temperature shifted to the right (higher T zones) and the maximum rate of weight loss was increased. In addition, lignin decomposition temperature interval was decreased whereas; cellulose decomposition temperature interval was increased. Increasing the heating rate from 5 to 20 K/min, hemicellulose decomposition temperature interval was increased. Total weight loss was slightly increased by the increase of gas flow rate. Kinetic parameters were calculated according to Coats Redfern method. It was found that activation energies of thermal decomposition reactions of hazelnut shell varied between 1.30 and 32.19 kJ/mol.     

Clam shell catalyst for continuous production of biodiesel

Continuous flow transesterification of waste frying oil (WFO) with methanol for the biodiesel production was tested in a laboratory scale jacketed reactive distillation (RD) unit packed with clam shell based CaO as solid catalyst. The physiochemical properties of the clam shell catalysts were characterized by X-ray Diffraction (XRD), Brunauer–Emmett–Teller (BET), Scanning Electron Microscopy (SEM), and Energy Dispersive Atomic X-ray Spectrometry (EDAX). The effects of the reactant flow rate, methanol-to-oil ratio, and catalyst bed height were studied to obtain the maximum methyl ester conversion. Reboiler temperature of 65°C was maintained throughout the process for product purification and the system reached the steady state at 7 hr. The experimental results revealed that the jacketed RD system packed with clam shell based CaO showed high catalytic activity for continuous production of biodiesel and a maximum methyl ester conversion of 94.41% was obtained at a reactant flow rate of 0.2 mL/min, methanol/oil ratio of 6:1, and catalyst bed height of 180 mm.     

Effect of Fenton pretreatment on anaerobic digestion of olive mill wastewater and olive mill solid waste in mesophilic conditions

The olive mill waste (OMW) generated from olive oil extraction process constitutes a major environmental concern owing to its high organic and mineral matters and acidic pH. Anaerobic digestion (AD) is a main treatment for reducing the organic matter and toxic substances contained in OMW and generating at the same time, energy in the form of biogas. AD of OMW that contains lignocellulose is limited by the rate of hydrolysis due to their recalcitrant structure. This study is devoted to the effect of Fenton process (FP) pretreatment on olive mill wastewater (OMSW) /olive mill solid waste (OMWW) co-digestion to improve their digestibility and in this way the biogas production. The FP pretreatment was performed in batch mode at 25°C, various H₂O₂/[Fe²⁺] ratios (100–1200), catalyst concentration ([Fe²⁺]) ranging from 0.25 to 2 mM, reaction time varying from 30 to150 min, and different pH (3–11). The best performance was obtained with H₂O₂/[Fe²⁺] = 1000, [Fe²⁺] = 1.5 mM, 120 min, and pH 3. Biochemical methane potential (BMP) tests conducted in batch wise digester and at mesophilic conditions (37 °C) showed that cumulative biogas and methane production were higher without FP treatment, and correspond to 699 and 416 mL/g VS, respectively. However, pre-treated OMSW results into an increase of 24% of methane yield. After 30 days of AD, the methane yield was 63%, 54%, and 48%, respectively, for OMSW treated without iron precipitation, with iron precipitation and untreated OMSW sample.     

CO2 capture from hot stove gas in steel making process

The capture of CO₂ from a hot stove gas in steel making process containing 30 vol% CO₂ by chemical absorption in a rotating packed bed (RPB) was studied. The RPB had an inner diameter of 7.6 cm, an outer diameter of 16 cm, and a height of 2 cm. The aqueous solutions containing 30 wt% of single and mixed monoethanolamine (MEA), 2-(2-aminoethylamino)ethanol (AEEA), and piperazine (PZ) were used. The CO₂ capture efficiency was found to increase with increasing temperature in a range of 303–333 K. It was also found to be more dependent on gas and liquid flow rates but less dependent on rotating speed when the speed was higher than 700 rpm. The obtained results indicated that the mixed alkanolamine solutions containing PZ were more effective than the single alkanolamine solutions. This was attributed to the highest reaction rate of PZ with CO₂. A higher portion of PZ in the mixture was more favorable to CO₂ capture. The highest gas flow rates allowed to achieve a desired CO₂ capture efficiency and the correspondent height of transfer unit (HTU) were determined at different aqueous solution flow rates. Because all the 30 wt% single and mixed alkanolamine solutions could result in a HTU less than 5.0 cm at a liquid flow rate of 100 mL/min, chemical absorption in a RPB instead of a packed bed adsorber is therefore suggested to capture CO₂ from the flue gases in steel making processes.     

Association of quantum dot nanoparticles with Pseudomonas aeruginosa biofilm

Quantum dots (QDs) of two different surface chemistries (carboxyl [COOH] and polyethylene glycol [PEG] modified) were utilized to determine the impact of surface functionality on QD mobility and distribution in Pseudomonas aeruginosa PAO1 biofilms. Confocal laser scanning microscopy was utilized to evaluate QD association with biofilm components (proteins, cells, and polysaccharides). Quantum dots did not preferentially associate with cell surfaces compared but did colocalize with extracellular proteins in the biofilm matrix. Neither PEG nor COOH QDs were found to be internalized by individual bacterial cells. Neither QD functionality nor flow rate of QD application (0.3 mL min(-1) or 3.0 mL min(-1)) resulted in a marked difference in QD association with P. aeruginosa biofilms. However, center of density determinations indicated COOH QDs could more easily penetrate the biofilm matrix by diffusion than PEG QDs. Biofilms with PEG QDs associated had rougher polysaccharide layers and rougher cell distribution than biofilms with COOH QDs. This work suggests natural biofilms may serve as deposition locations in natural and engineered environmental systems, and biofilm structural parameters may change based on exposure to nanomaterials of varied physical characteristics.     

Cost analysis in laccase production

In this paper the cost of producing the enzyme laccase by the white-rot fungus Trametes pubescens under both submerged (SmF) and solid-state fermentation (SSF) conditions was studied. The fungus was cultured using more than 45 culture medium compositions. The cost of production was estimated by analyzing the cost of the culture medium, the cost of equipment and the operating costs. The cost of the culture medium represented, in all cases, the highest contribution to the total cost, while, the cost of equipment was significantly low, representing less than 2% of the total costs. The cultivation under SSF conditions presented a final cost 50-fold lower than the one obtained when culturing under SmF conditions at flask scale. In addition, the laccase production under SSF conditions in tray bioreactors reduced the final cost 4-fold compared to the one obtained under SSF conditions at flask scale, obtaining a final price of 0.04 cent €/U.     

Direct utilization of kitchen waste for bioethanol production by separate hydrolysis and fermentation (SHF) using locally isolated yeast

Kitchen wastes containing high amounts of carbohydrates have potential as low-cost substrates for fermentable sugar production. In this study, enzymatic saccharification of kitchen waste was carried out. Response surface methodology (RSM) was applied to optimize the enzymatic saccharification conditions of kitchen waste. This paper presents analysis of RSM in a predictive model of the combined effects of independent variables (pH, temperature, glucoamylase activity, kitchen waste loading, and hydrolysis time) as the most significant parameters for fermentable sugar production and degree of saccharification. A 100 mL of kitchen waste was hydrolyzed in 250 mL of shake flasks. Quadratic RSM predicted maximum fermentable sugar production of 62.79 g/L and degree of saccharification (59.90%) at the following optimal conditions: pH 5, temperature 60°C, glucoamylase activity of 85 U/mL, and utilized 60 g/L of kitchen waste as a substrate at 10 h hydrolysis time. The verification experiments successfully produced 62.71 ± 0.7 g/L of fermentable sugar with 54.93 ± 0.4% degree of saccharification within 10 h of incubation, indicating that the developed model was successfully used to predict fermentable sugar production at more than 90% accuracy. The sugars produced after hydrolysis of kitchen waste were mainly attributed to monosaccharide: glucose (80%) and fructose (20%). The fermentable sugars obtained were subsequently used as carbon source for bioethanol production by locally isolated yeasts: Saccharomyces cerevisiae, Candida parasilosis, and Lanchancea fermentati. The yeasts were successfully consumed as sugars hydrolysate, and produced the highest ethanol yield ranging from 0.45 to 0.5 g/g and productivity between 0.44 g L^–1 h^–1 and 0.47 g L^–1 h^–1 after 24-h incubation, which was equivalent to 82.06–98.19% of conversion based on theoretical yield.     

Pyrolysis of commingled waste textile fibers in a batch reactor: Analysis of the pyrolysis gases and solid product

The main object of this study was the investigation of the thermal recycling of commingled waste textile fibers, with the aim of the production of useful end products. Differential scanning calorimetry/Thermo gravimetric analysis (DSC/TGA) was applied to determine the thermal degradation characteristics of the commingled waste textile fibers and there are two peaks located at the temperature ranges of 299–360°C and 399–500°C. Commingled waste fiber was pyrolyzed in a nitrogen atmosphere in relation to three different temperatures (500, 600, and 700°C), heating rates (25 and 50°C min^?1), and retention times (15 and 30 min). The effect of the experimental conditions such as pyrolysis temperature, heating rates, and retention time on the formation of char and gas--liquid products was investigated and the product yields were determined from the rate of the weight loss. The highest conversion rate 82.9 wt.% liquid--gas product and 17.1 wt.% char product was achieved at 700°C. Pyrolysis gases were taken for every 7, 15, and 25 min and were analyzed for major components such as CO, CO₂, CH₄, and H₂ by gas chromatography. The pyrolysis char called as carbon black derived from the pyrolysis of commingled waste textile fibers was analyzed for a range of properties, including the elemental analysis, moisture content, ash content, calorific value, and trace metal analysis.     

The use of tailor-made acidic deep eutectic solvents for preparation of quercetin-enriched extracts from onion solid wastes

The current examination dealt with the development of a methodology to produce quercetin, a multifunctional bio-flavonoid, by designing task-specific, highly acidic deep eutectic solvents, based on glycerol and natural organic acids. The purpose was to achieve a simultaneous hydrolysis of spiraeoside, the major quercetin glycoconjugate occurring in onion solid wastes, and quercetin extraction. After an initial performance screening, the combination of glycerol/oxalic acid was identified as the highest-performing system, and further investigation showed that the most efficacious molar ratio was glycerol/oxalic acid 3:1. Further study of hydrolysis/extractions conditions suggested 30 min, at 130°C, to be the best operating conditions, giving the highest yield of 19.65 mg quercetin per grams of dry mass. The extract obtained under these conditions displayed significantly enhanced antiradical activity, compared to control extracts prepared with water or aqueous ethanol. On the other hand, results on the ferric-reducing power were rather contradictory. It is proposed that such a methodology may be implemented to valorize onion solid wastes, for the production of extracts significantly enriched in quercetin, with increased antiradical properties.     

城市生活垃圾中可生化单基质的厌氧消化

在厌氧消化系统中，发酵细菌最主要的利用基质是淀粉、纤维素、脂肪和蛋白质等。本试验分别选取米饭、黄豆、芹菜和肥肉为上述四种基质的代表物质，通过对各物质进行的厌氧消化试验，探讨了它们的厌氧消化性能。结果表明。米饭在发酵初期降解速率最快，酸化也最明显。同时将消化初始阶段的pH控制在6．5时能使消化进入产甲烷阶段，没控制的只能停留在水解产酸阶段。将黄豆厌氧消化初期的pH控制在6．5并不能使消化顺利进行。将芹菜厌氧消化的初始pH值控制在6．5时可以加快它的降解速率。肥肉的厌氧消化也只有在对其消化进程控制pH值时才能顺利被降解。同时肥肉在厌氧消化进程中表现出了高产甲烷性能，产甲烷阶段累积产气量达13758mL，占总产气量的93．59％．     

Adsorption of methylene blue from aqueous solution by jackfruit (Artocarpus heteropyllus) leaf powder: A fixed-bed column study

Continuous fixed-bed studies were undertaken to evaluate the efficiency of jackfruit leaf powder (JLP) as an adsorbent for the removal of methylene blue (MB) from aqueous solution under the effect of various process parameters like bed depth (5–10 cm), flow rate (30–50 mL/min) and initial MB concentrations (100–300 mg/L). The pH at point of zero charge (pH_PZC) of the adsorbent was determined by the titration method and a value of 3.9 was obtained. A FTIR of the adsorbent was done before and after the adsorption to find the potential adsorption sites for interaction with methylene blue molecules. The results showed that the total adsorbed quantities and equilibrium uptake decreased with increasing flow rate and increased with increasing initial MB concentration. The longest breakthrough time and maximum MB adsorption were obtained at pH 10. The results showed that the column performed well at low flow rate. Also, breakthrough time and exhaustion time increased with increasing bed depth. The bed-depth service time (BDST) model and the Thomas model were applied to the adsorption of MB at different bed depths, flow rates, influent concentrations and pH to predict the breakthrough curves and to determine the characteristic parameters of the column that are useful for process design. The two model predictions were in very good agreement with the experimental results at all the process parameters studied indicating that they were very suitable for JLP column design.     

Application of response surface methodology for the optimization of biodiesel production from yellow mustard (Sinapis alba L.) seed oil

In the present study, response surface methodology (RSM) involving central composite design (CCD) was applied to optimize the reaction parameters of biodiesel production from yellow mustard (Sinapis alba L.) seed oil during the single-step transesterification process. A total of 30 experiments were designed and performed to determine under the effects of variables on the biodiesel yield such as methanol to oil molar ratio (2:1–10:1), catalyst concentration (0.2–1.0 wt.% NaOH), reaction temperature (50–70°C), and reaction time (30–90 min). The second order polynomial model was used to predict the biodiesel yield and coefficient of determination (R²) was found to be at 0.9818. The optimum biodiesel yield was calculated as 96.695% from the model with the following reaction conditions: 7.41:1 of methanol to oil molar ratio, 0.63 wt. % NaOH of catalyst concentration, 61.84°C of reaction temperature, and 62.12 min of reaction time. It is seen that the regression model results were in agreement with the experimental data. The results showed that RSM is a suitable statistical technique for optimizing the reaction parameters in the transesterification process in order to maximize the biodiesel yield.     

Study of the influence of dilute acid pre-treatment conditions on glucose recovery from Moringa oleifera Lam for fuel-ethanol production

The influence of temperature (175 to 195°C), residence time (5 to 15 min), and sulfuric acid concentration in high (2 to 4% w/w) and low (0.5 to 1.5% w/w) levels in dilute acid pretreatment of Moringa oleifera Lam is studied. Glucose recoveries in the liquid fraction and in the hydrolyzed insoluble fraction as well as the presence of inhibitors in the liquid fraction are determined. Best experimental results are achieved at 185°C, 2% w/w acid concentration, and 5 min reaction time obtaining a glucose recovery of 83.68%. An increment in 48.81% in glucose yield compared with the one of not pretreated Moringa is obtained. 0.13 g ethanol/g Moringa from fermentation of pre-hydrolysate and hydrolysate obtained at the optimal pre-treatment conditions are obtained.     

Reforming of CO2-containing natural gas with steam in AC gliding arc discharge for hydrogen production

In this study, a low-temperature gliding arc discharge system was used to investigate the effects of steam content and operational parameters, i.e. total feed flow rate, applied voltage, and input frequency, on the reforming performance of CO₂-containing natural gas. The addition of steam less than 10% was found to enhance both selectivities for hydrogen and carbon monoxide with a significant reduction of power consumptions. The highest hydrogen selectivity and yield with the lowest power consumptions were achieved at a steam content of 10 mol%, a total feed flow rate of 100 cm³/min (corresponding to a very short residence time of 1.37 s), an applied voltage of 13.5 kV and an input frequency of 300 Hz. Under these optimum conditions, the oxidative dehydrogenation reactions to produce hydrogen were dominant with the minimum activities of all undesired reactions of cracking and coupling. Both of the short residence time (1.37 s) with a low bulk temperature (lower than 200°C) in the plasma zone under atmospheric pressure, indicate that the studied plasma reactor (gliding arc system) is superior to conventional catalytic reactors for reforming of natural gas.