耐Cd2+假单胞菌富集Cd2+的研究

从安徽某冶炼厂污染土壤中分离出一株能高度耐Cd2+和富集Cd2+的菌株J5.通过光学显微镜、透射电镜、扫描电镜观察到,菌株J5在含2.0 mmol/L Cd2+的液体培养基和75.0 mmol/L Cd2+固体培养基上多以聚集成团块形式逐渐富集CA2+;液体培养基中菌株J5多以四角形的晶体结构存在,而在固体培养基上则以胞外聚集物存在;菌株细胞壁内外密布含Cd2+的颗粒.菌株J5对1.0 mmol/L Cd2+的积累率为99.1%,菌株内Cd2+质量分数可达32%.     

一株石油烃降解菌的筛选、鉴定及对石油烃模式物的降解特性研究

从胶洲湾P3-1站位采集的石油污染海洋底泥中筛选得到一株能以原油为唯一碳源生长良好的石油烃降解菌株JZ3-21。经过形态、生理生化特征试验和16S rDNA序列分析结果,鉴定JZ3-21为恶臭假单胞菌属（Pseudomonas puti-da）;实验研究了该菌株对5种石油烃模式物（正十六烷、甲苯、萘、芘和邻苯二酚）的降...     

N-乙烯基吡咯烷酮降解菌的筛选、降解特性及其竹炭固定化

从活性污泥中分离筛选得到1株N-乙烯基吡咯烷酮(NVP)高效降解菌株ZF1,根据菌株ZF1的形态特征、生理生化特性和16S rRNA基因序列同源性分析,将其初步鉴定为产脲节杆菌(Arthrobacter ureafaciens)。菌株ZF1能以NVP为唯一碳、氮源进行生长,并在60 h内完全降解200 mg·L~(-1)的NVP。菌株ZF1降解NVP的最适环境条件为温度30℃,初始pH 7.0,Na Cl浓度7 g·L~(-1)。为了更好地实现其在实际废水中的应用,将菌株ZF1固定到竹炭上,扫描电镜观察表明ZF1能很好的附着在竹炭表面,且固定菌对NVP的降解效率明显高于游离菌。游离菌和固定菌对NVP的降解均符合一级动力学模型。重复利用5次后,固定菌对NVP的降解率仍能达到98%。     

一株PVA降解菌的筛选及其降解条件的优化

从被PVA直接污染的环境中筛选获得一株能高效降解聚乙烯醇的微生物菌株Z5。对其生长过程及PVA降解过程进行研究,发现该菌株在48 h内可降解79.24%的聚乙烯醇(PVA)。同时研究了Z5菌株的降解特性,结果表明,该菌株降解PVA最适条件为:温度30℃、pH6.2、装液量30 mL;牛肉膏、蛋白胨、NaCl、PVA浓度分别为:0.05 g/L、0.1 g/L、2 g/L和2 g/L。     

三乙胺降解菌SYA-1的分离、降解性能与动力学

从农药废水处理池的活性污泥中分离筛选得到1株高效三乙胺降解菌株SYA-1,根据菌株SYA-1的形态特征、生理生化特性和16S rRNA基因序列同源性分析,此菌株鉴定为Achromobacter sp.。菌株SYA-1能以三乙胺为惟一碳、氮源生长,并在24 h内完全降解200 mg/L的三乙胺。环境因素影响实验表明,在温度30℃,初始pH 7.0,NaCl浓度≤10 g/L条件下,菌株SYA-1生长良好且对三乙胺的降解效率最佳;金属离子对菌株生长和三乙胺降解的抑制程度表现为:Cu2+Co2+Ag+Cd2+Fe3+Pb2+。菌株SYA-1降解三乙胺的动力学过程可用Haldane模型模拟,其参数为μmax=0.123h-1;K s=82 mg/L;K i=215 mg/L。为含三乙胺废水的生物降解提供了理论依据和菌株资源。     

一株1，2-二氯苯降解菌的分离鉴定及其降解特性

采用富集驯化方法,从盐城芦苇湿地根际土壤中分离得到一株可高效降解1,2-二氯苯的菌株,命名为DL-1。该菌株可以在以1,2-二氯苯为惟一碳源的无机培养基上生长,能够耐受最高浓度为200 mg/L的1,2-二氯苯。根据形态特征观察、生理生化鉴定和16S rDNA序列同源性分析,该目标菌株被鉴定为蜡质芽孢杆菌（Bacillus cereus）。菌株DL-1对1,2-二氯苯降解性能研究表明,该菌株为一株兼性厌氧菌,其适宜降解浓度、适宜温度、适宜pH值和适宜接种量分别为120mg/L、32℃、7和10%,在适宜降解条件下降解12,-二氯苯4 d其降解率达到80.3%。本实验为利用该菌株降解12,-二氯苯污水的应用提供了理论基础。     

1，4-二氯苯降解菌的分离及其降解特性研究

从某污水处理曝气池的活性污泥中分离出一株能够以1，4-二氯苯为唯一碳源和能源生长的菌株DEB-1，通过形态特征和生理生化试验初步鉴定为黄杆菌属（Flavobacterium sp.）。实验结果表明，该菌株最适降解温度为32℃、最适降解pH为7.8，24 h对100 mg/L的1，4-二氯苯的降解率达94.5%。菌株DEB-1的降解谱较广，对5种氯苯类物质具有较高的降解率。并进一步研究了DEB-1的1，4-二氯苯降解酶粗酶液的性质，其最适反应温度和pH分别为30℃和8.5。对处理含氯代芳香化合物的有机废水具有一定的意义。     

一株苯好氧降解菌的分离及其降解特性研究

从一长期被苯类工业废水污染的土壤中驯化分离出一株能快速降解苯胺的菌株,初步鉴定为假单胞菌属。该菌株在5-35℃,都可以20mg/L的苯为碳源进行生长并完全降解苯,最适宜的生长温度为25℃;在pH为5-9范围内,可以生长并降解20mg/L的苯,偏碱性更适合细菌生长;培养过程中振荡速率大于120r/min,降解速率最大。     

高效阿特拉津降解菌株DNSIO降解条件优化

从长期施用阿特拉津的寒地黑土耕层（0～10cm）土壤中筛选到一株能以除草剂阿特拉津为氮源生长的降解菌株，结合16SrRNA序列分析结果，将该菌株命名为Arthrobacter sp．DNSl0。在接种量为10。CFU／mL的条件下，菌株DNSl0在24h内对100mg／L阿特拉津的降解率为99．41％。单因子实验结果表明，菌株DNSl0适宜生长和降解的条件范围是：温度25～35＇12，pH值5．0～8．0，培养液盐度0．1％～2％，对阿特拉津最大耐受浓度可达1200mg／L。正交实验法进一步表明，该菌株保持较好生长及降解能力的最优方案是温度30℃，pH值7．5，培养液盐度0．5％。影响其降解能力的环境因素的主次顺序依次是：温度〉盐度〉pH值。     

饮用水除氨氮功能菌株的筛选及降解特性

从松花江原水中筛选出2株异养菌YX1和YX2,经生理生化及16S rDNA序列鉴定,YX1为微杆菌属(Microbacterium sp.),YX2为不动杆菌属(Acinetobacter sp.)。5℃菌株YX1的世代时间为3.03 h,菌株YX2的世代时间为3.87h。应用生物增强活性炭技术研究了异养菌株YX1和YX2对氨氮的降解特征,结果表明,菌株经过3~4 d的适应期后,在低温5℃对氨氮具有较强的降解能力,且环境条件影响菌株对氨氮的降解效果。菌株YX1和YX2在高溶解氧浓度下氨氮降解效果好,属于好氧细菌,降解氨氮的最适合温度为12~15℃,属于耐冷型中温菌,最适宜的pH为弱碱性(7.5~8.0),以乙酸盐为碳源时对氨氮降解能力最强,其次为葡萄糖柠檬酸三钠碳酸钙甘油,以上结果可为低温水源水中氨氮的去除提供新的技术方法和理论依据。     

Dioxin- and POP-contaminated sites—contemporary and future relevance and challenges

BACKGROUND, AIM AND SCOPE: Once they have been generated, polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs) and other persistent organic pollutants (POPs) can persist in soils and sediments and in waste repositories for periods extending from decades to centuries. In 1994, the US EPA concluded that contaminated sites and other reservoirs are likely to become the major source of contemporary pollution problems with these substances. With this in mind, this article is the first in a new series in ESPR under the title 'Case Studies on Dioxin and POP Contaminated Sites--Contemporary and Future Relevance and Challenges', which will address this important issue. The series will document various experiences from sites contaminated with PCDD/F and other POPs. This article provides an overview of the content of the articles comprising the series. In addition, it provides a review of the subject in its own right and identifies the key issues arising from dioxin/POP-contaminated sites. Additionally, it highlights the important conclusions that can be drawn from these examples. The key aim of this article and of the series as a whole is to provide a comprehensive overview of the types of PCDD/F contaminated sites that exist as a result of historical activities. It details the various processes whereby these sites became contaminated and attempts to evaluate their contemporary relevance as sources of PCDD/Fs and other POPs. It also details the various strategies used to assess these historical legacies of contamination and the concepts developed, or which are under development, to effect their remediation. MAIN FEATURES: Special sessions on 'Contaminated sites--Cases, remediation, risk and policy' were held at the DIOXIN conferences in 2006 and 2007, and this theme will be continued at DIOXIN 2008 to be held in Birmingham. Selected cases from the approximately 70 contributions made to these sessions, together with some additional invited case studies are outlined together with the key issues they raise. By evaluating these cases and adding details of experiences published in the current literature, an overview will be given of the different features and challenges of dioxin and POP-contaminated sites. RESULTS: This article provides a systematic categorisation of types of PCDD/F and POP-contaminated sites. These are categorised according to the chemical or manufacturing process, which generated the PCDD/Fs or POPs and also includes the use and disposal aspects of the product life cycle in question. The highest historical PCDD/F and dioxin-like polychlorinated biphenyl (PCB) contamination burdens have arisen as a result of the production of chlorine and of chlorinated organic chemicals. In particular, the production of chlorinated pesticides, PCBs and the related contaminated waste streams are identified being responsible for historical releases of toxic equivalents (TEQs) at a scale of many tonnes. Along with such releases, major PCDD/F contaminated sites have been created through the application or improper disposal of contaminated pesticides, PCBs and other organochlorine chemicals, as well through the recycling of wastes and their attempted destruction. In some extreme examples, PCDD/F contaminated sites have also resulted from thermal processes such as waste incinerators, secondary metal industries or from the recycling or deposition of specific waste (e.g. electronic waste or car shredder wastes), which often contain chlorinated or brominated organic chemicals. The examples of PCDD/F and dioxin-like PCB contamination of fish in European rivers or the impact of contaminated sites upon fishing grounds and upon other food resources demonstrate the relevance of these historical problems to current and future human generations. Many of the recent food contamination problems that have emerged in Europe and elsewhere demonstrate how PCDD/F and dioxin like PCBs from historical sources can directly contaminate human and animal feedstuffs and indeed highlight their considerable contemporary relevance in this respect. Accordingly, some key experiences and lessons learnt regarding the production, use, disposal and remediation of POPs from the contaminated sites are summarised. DISCUSSION: An important criterion for evaluating the significance and risks of PCDD/Fs and other POPs at contaminated sites is their present or future potential for mobility. This, in turn, determines to a large degree their propensity for off-site transport and environmental accessibility. The detailed evaluation of contaminated site cases reveals different site-specific factors, which influence the varied pathways through which poor water-soluble POPs can be mobilised. Co-contaminants with greater water solubility are also typically present at such sites. Hence, pumping of groundwater (pump and treat) is often required in addition to attempting to physically secure a site. At an increasing number of contaminated sites, securing measures are failing after relatively short time spans compared to the time horizon, which applies to persistent organic pollutant contamination. Due to the immense costs and challenges associated with remediation of contaminated sites 'monitored natural attenuation' is increasingly gaining purchase as a conceptual remediation approach. However, these concepts may well prove limited in their practical application to contaminated sites containing persistent organic pollutants and other key pollutants like heavy metals. CONCLUSIONS: It is inevitable, therefore, that dioxin/POP-contaminated sites will remain of contemporary and future relevance. They will continue to represent an environmental issue for future generations to address. The securing and/or remediation of dioxin/POP-contaminated sites is very costly, generally in the order of tens or hundreds of millions of dollars. Secured landfills and secured production sites need to be considered as constructions not made for 'eternity' but built for a finite time scale. Accordingly, they will need to be controlled, supervised and potentially repaired/renewed. Furthermore, the leachates and groundwater impacted by these sites will require ongoing monitoring and potential further remediation. These activities result in high maintenance costs, which are accrued for decades or centuries and should, therefore, be compared to the fully sustainable option of complete remediation. The contaminated site case studies highlight that, while extensive policies and established funds for remediation exist in most of the industrialised western countries, even these relatively well-regulated and wealthy countries face significant challenges in the implementation of a remediation strategy. This highlights the fact that ultimately only the prevention of contaminated sites represents a sustainable solution for the future and that the Polluter Pays Principle needs to be applied in a comprehensive way to current problems and those which may emerge in the future. RECOMMENDATIONS AND PERSPECTIVES: With the continuing shift of industrial activities in developing and transition economies, which often have poor regulation (and weak self-regulation of industries), additional global challenges regarding POPs and other contaminated sites may be expected. In this respect, a comprehensive application of the "polluter pays principle" in these countries will also be a key to facilitate the clean-up of contaminated areas and the prevention of future contaminated sites. The threats and challenges of contaminated sites and the high costs of securing/remediating the problems highlight the need for a comprehensive approach based upon integrated pollution prevention and control. If applied to all polluting (and potentially polluting) industrial sectors around the globe, such an approach will prove to be both the cheapest and most sustainable way to underpin the development of industries in developing and transition economies.     

Sorption and desorption of Cu and Cd by macroalgae and microalgae

The sorption and desorption of Cu and Cd by two species of brown macroalgae and five species of microalgae were studied. The two brown macroalgae, Laminaria japonica and Sargassum kjellmanianum, were found to have high capacities at pHs between 4.0 and 5.0 while for microalgae, optimum pH lay at 6.7. The presence of other cations in solution was found to reduce the sorption of the target cation, suggesting a competition for sorption sites on organisms. Sorption isotherms obeyed the Freundlich equation, suggesting involvement of a multiplicity of mechanisms and sorption sites. For the microalgae tested, Spirulina platensis had the highest capacity for Cd, followed by Nannochloropsis oculata, Phaeodactylum tricornutum, Platymonas cordifolia and Chaetoceros minutissimus. The reversibility of metal sorption by macroalgae was examined and the results show that both HCl and EDTA solutions were very effective in desorbing sorbed metal ions from macroalgae, with up to 99.5% of metals being recovered. The regenerated biomass showed undiminished sorption performance for the two metals studied, suggesting the potential of such material for use in water and wastewater treatment.     

Persistence and dissipation kinetics of trifloxystrobin and tebuconazole in onion and soil

The persistence and dissipation kinetics of trifloxystrobin and tebuconazole on onion were studied after application of their combination formulation at a standard and double dose of 75 + 150 and 150 + 300 g a.i. ha^?1. The fungicides were extracted with acetone, cleaned-up using activated charcoal (trifloxystrobin) and neutral alumina (tebuconazole). Analysis was carried out by gas chromatograph (GC) and confirmed by gas chromatograph mass spectrometry (GC-MS). The recovery was above 80% and limit of quantification (LOQ) 0.05 mg kg^?1 for both fungicides. Initial residue deposits of trifloxystrobin were 0.68 and 1.01 mg kg^?1 and tebuconazole 0.673 and 1.95 mg kg^?1 from standard and double dose treatments, respectively. Dissipation of the fungicides followed first-order kinetics and the half life of degradation was 6–6.6 days. Matured onion bulb (and field soil) harvested after 30 days was free from fungicide residues. These findings suggest recommended safe pre-harvest interval (PHI) of 14 and 25 days for spring onion consumption after treatment of Nativo 75 WG at the standard and double doses, respectively. Matured onion bulbs at harvest were free from fungicide residues.     

Kinetic and structural relationships of transition monomeric and oligomeric carboxyl- and choline-esterases

The kinetic and structural relationships of eight electrophoretically pure mammalian serum and liver serine carboxylesterases (CE) and cholinesterases (ChE) have been studied. Eight CE's and ChE's, which were fully resolved but only partially purified, provided additional information. Five of the electrophoretically pure esterases were monomeric, and of these, four belonged to a new and widely distributed class. These four monomeric esterases hydrolyzed choline esters, but at widely differing rates. Thus two were termed monomeric butyrylcholinesterases, mBuChE I and II, and two were monomeric CE's (mCE). The rabbit liver mCE was not a subunit of the oligomeric CE (oCE), although the oCE also hydrolyzed choline esters at a very low rate. The complex kinetics of the mCE's, mBuChE's, oCE's, and of the oligomeric BuChE's of horse and human serum could be interpreted according to a single reaction scheme involving an allosteric site and the equation derived from it. Thus activation and inhibition at high substrate concentrations, together with sigmoidal activity versus substrate concentration plots, all of which characterize the reactions of these esterases, could be interpreted by a single scheme and equation. Structural and kinetic comparisons showed a progressive transition of properties from the oCE's through the mCE's to the oBuChE's. One of the purified mCE's was from horse serum, and it exhibited physical and kinetic properties unlike those of the liver mCE's or oCE's.     

Bacterial and archaeal diversity in oil fields and reservoirs and their potential role in hydrocarbon recovery and bioprospecting

Environmental Science and Pollution Research - Hydrocarbon is a primary source of energy in the current urbanized society. Considering the increasing demand, worldwide oil productions are declining...     

Sorption and Desorption Behavior of Chloroanilines and Chlorophenols on Montmorillonite and Kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Sorption and desorption behavior of chloroanilines and chlorophenols on montmorillonite and kaolinite

The bioavailability of pollutants, pesticides and/or their degradation products in soil depends on the strength of their sorption by the different soil components, particularly by the clay minerals. This study reports the sorption-desorption behavior of the environmentally hazardous industrial pollutants and certain pesticides degradation products, 3-chloroaniline, 3,4-dichloroaniline, 2,4,6-trichloroaniline, 4-chlorophenol, 2,4-dichlorophenol and 2,4,6-trichlorophenol on the reference clays kaolinite KGa-1 and Na-montmorillonite SWy-l. In batch studies, 2.0 g of clay were equilibrated with 100.0 mL solutions of each chemical at concentrations ranging from 10.0 to 200.0 mg/L. The uptake of the compounds was deduced from the results of HPLC-UV-Vis analysis. The lipophilic species were best retained by both clay materials. The most lipophilic chemical used in the study, 2,4,6-trichloroaniline, was also the most strongly retained, with sorption of up to 8 mg/g. In desorption experiments, which also relied on HPLC-UV-Vis technique, 2,4,6-trichloroaniline was the least desorbed from montmorillonite. However, on kaolinite all of the compounds under study were irreversibly retained. The experimental data have been modelled according to the Langmuir and Freundlich isotherms. A hypothesis is proposed concerning the sorption mechanism and potential applications of the findings in remediation strategies have been suggested.     

Synthesis and characterization of m- and p-methylbenzyl-mercapturic acids derived from m- and p-xylenes

Chemical synthesis and physical properties of two mercapturic acids suggested as urinary metabolites of m- and p-xylenes ace described. These compounds may be used for the identification and quantivative determination by high-performance liquid chromatography of the corresponding mercapturic acids in urine.     

Sources and fate of PCDD and PCDF

PCDD and PCDF were found in urban air particulates from St. Louis and Washington, D.C., and in sediments from the Great Lakes and Siskiwit Lake, Isle Royale. The similarity between the PCDD and PCDF found in air particulates and sediment samples and the presence of PCDD and PCDF in sediment from Siskiwit Lake (a location which can receive only atmospheric inputs) suggest that these compounds are emitted to the atmosphere from combustion sources. The historical input of PCDD and PCDF to dated sediment cores shows a strong increase since 1940, and this suggests that the incineration of chlorinated organic compounds is an important source of PCDD and PCDF to the environment.     

Levels of PCDDs and PCDFs in products and effluent from the Swedish pulp and paper industry and chloralkali process

Within the Swedish Dioxin Survey various samples from the pulp and paper industry and the chloralkali process have been analyzed by congener specific analytical methods. In addition to the generally discussed “bleaching pattern” of the tetrachlorinated congeners, these samples also contained higher chlorinated congeners like hexa-CDDs, hepta-CDFs, octa-CDD and octa-CDF. Consequently it is recommended that samples from the pulp industry should be analyzed for all PCDDs and PCDFs (tetra- through octa-). Counted as Nordic Toxic Equivalents (NTEQ), the recycled pulp samples had the highest contamination level followed by TMP, unbleached sulfite and bleached softwood and hardwood. In addition to the bleaching process, various chemicals used in the pulping, bleaching and wastewater treatment can contribute to the contamination.