多层光源内置式气-液-固循环流化床光催化降解双酚A

悬浮浆态光催化反应体系具有固-液接触面积大、过程效率高和处理量较大的优点,但存在浆态体系中纳米催化剂难于分离回收的问题,为解决这一难题,提出了在废水污染物光催化降解过程中使用易于沉降分离的微米级颗粒光催化荆,并与新设计的多层光源内置式气-液-固循环流化床相结合组成的光催化反应体系.以微米级颗粒Gd-TiO2为光催化剂,...     

上转换发光剂掺杂纳米TiO2的制备及可见光降解乙基紫的研究

合成了一种新型含有稀土金属Er的上转换发光剂40CdF₂·60BaF₂·1.6Er₂O₃,此上转换发光剂在488 nm可见光的激发下,产生了5个波长均小于387 nm的上转换紫外光发射峰.采用超声波分散的方法制备出了上转换发光剂掺杂的纳米TiO₂可见光光催化剂.利用X-射线衍射(XRD)及透射电镜(TEM)对催化剂进行了表征.以乙基紫染料为研究对象,研究了在(三基色灯下发出的)可见光的照射下该可见光光催化剂的催化降解性能,并与未掺杂的纳米TiO₂粉末的催化性能进行了对比.结果表明,作为掺杂成分的上转换发光剂可有效地将可见光转化为紫外光并被纳米TiO₂粉末吸收利用,在可见光照射12.0 h后乙基紫降解率达到了99.68%,大大高于未掺杂纳米TiO2时的降解率.     

光催化降解有机磷农药的研究

研究以ＴｉＯ２粉末作为光催化剂,光降解３种不同结构的有机磷农药的可行性。结果表明,有机磷农药结构不同其光降解率不同;浓度１．０×１０－４ｍｏｌ／Ｌ的４种有机磷农药,３７５Ｗ中压汞灯照射４０ｍｉｎ有机磷将完全转变为无机磷,并检测出人效磷农药催化降解的部分中间产物。研究光催化剂ＴｉＯ２的用量、空气流量、外加Ｆｅ３＋浓度对光催化降解的影响,并初步探讨了机理。     

TiO2-石墨烯（Gn）复合材料光催化降解O3研究

通过改性Hummer法及溶胶凝胶法,制备出TiO2-石墨烯光催化复合材料.经吸附-光催化活性实验选出光催化活性最高的含C量为1.5%(质量分数)的TiO2-石墨烯复合材料,并在自行设计的模拟大型客机环境的气相光催化反应器中,进行O3光催化降解实验研究.结果表明,TiO2-石墨烯复合光催化材料在较短时间内对O3有较高的降解效率,且其光催化活性显著优于纯TiO2材料.初始O3浓度为(0.150～0.200)×10-6时,复合光催化剂受紫外光激发60 min的光催化降解率为66.12%,初始O3浓度为(0.950～1.000)×10-6时,其光催化降解率约为77%,较低浓度时((0.100～0.150)×10-6),O3去除率也能达到45.45%.此外,通过探讨光催化材料的重复使用性能,表明复合光催化剂重复使用4次以内,其对O3的光催化降解率保持基本稳定.     

Photocatalytic degradation of organochlorine compounds using TiO2 supported on fiberglass cloth

The feasibility of photocatalytic degradation of organochlorine compounds using TiO₂ supported on fiberglass cloth as a photocatalyst was studied. The results showed that 2.0×10^-4 mol/dm³ of dichloroethylene, trichloroethylene and tetrachloroethylene can be completely photocatalytically degraded within a short time under illumination with a 375W medium pressure mercury lamp. The effects of parameters such as illumination time, initial concentration of organochlorine compounds, amount of air flow and concentration of H₂O₂ on the photocatalytic degradation were investigated. The TiO₂ supported on the fiberglass was not easily detached and after 500h illumination there was no significant loss of photocatalytic activity of TiO₂. The passible mechanisms of photocatalytic degradation were discussed.     

Photocatalytic degradation of dichlorvos using TiO2 supported on hollow glass microbeads

In this paper, a method for TiO₂ supported on hollow glass microbeads was described and the feasibility of photocatalytic degradation of dichlorvos using supported TiO₂(TiO₂/beads) was studied. The results showed that 1.0×10^-4 mol.dm^-3 of dichlovos could be completely photocatalytically degraded into PO₄^3- after 120 min illumination with a 375 W medium pressure mercury lamp. The effects of the amount of TiO₂/beads and concentration of Cu²⁺ on the photocatalytic degradation were also investigated. Some intemediate products of photocatalytic degradation of dichlorvos were detected.     

Photocatalytic degradation of phenanthrene on soil surfaces in the presence of nanometer anatase TiO2 under UV-light

The effect of nanometer anatase TiO₂ was investigated on the photocatalytic degradation of phenanthrene on soil surfaces under a variety of conditions. After being spiked with phenanthrene, soil samples loaded with different amounts of TiO₂ (0 wt.%, 1 wt.%, 2 wt.%, 3 wt.%, and 4 wt.%) were exposed to UV-light irradiation for 25 hr. The results indicated that the photocatalytic degradation of phenanthrene followed the pseudo first-order kinetics. TiO₂ significantly accelerated the degradation of phenanthrene with the half-life reduced from 45.90 to 31.36 hr for TiO₂ loading of 0 wt.% and 4 wt.%, respectively. In addition, the effects of H₂O₂, light intensity and humic acid on the degradation of phenanthrene were investigated. The degradation of phenanthrene increased with the concentration of H₂O₂, light intensity and the concentration of humic acids. It has been demonstrated that the photocatalytic method in the presence of nanometer anatase TiO₂ was a very promising technology for the treatments of soil polluted with organic substances in the future.     

RGO/TiO2光催化降解2,4-二氯苯氧乙酸研究

通过Hummers法及紫外光/热还原工艺制得还原氧化石墨烯(RGO),采用溶胶-凝胶-煅烧法,以RGO和钛酸酊脂为前驱体制备出RGO/TiO2光催化复合材料,并利用XRD、FT-IR等对其进行了表征.对RGO/TiO2光催化降解性能的研究发现,复合光催化剂RGO/TiO2对2,4-二氯苯氧乙酸(2,4-D)的光催化降解活性显著优于纯TiO2,并且发现负载量和pH值对光催化降解性能有较大的影响:RGO/TiO2投加量为1.2g·L~(-1)、RGO负载量2%、pH为3、初始浓度为50 mg·L~(-1)反应12 h,2,4-D去除率达到98.75%;2,4-D降解率随着RGO/TiO2投加量的增大先增大后减小;RGO/TiO2对2,4-D的降解为脱氯还原和催化氧化过程,产生氯酚、苯酚等中间产物.     

TiO2降解迪美唑的动力学及活性物质分析

兽类抗生素迪美唑是一种新兴的污染物质,对环境和人类健康具有潜在危害.以紫外光为光源,以TiO2为催化剂,对其进行光催化降解,考察了溶液pH值、TiO2投加量、溶液的初始浓度等影响因素对迪美唑降解效果的影响.结果表明,在TiO2投加量为1 g·L-1,迪美唑初始浓度为40 mg·L-1,溶液pH为11的最优条件下反应90 min后,迪美唑的去除率为90%,反应速率为0.025 7 min-1.反应符合伪一级动力学模型.光催化降解迪美唑有两个途径:一是·OH氧化过程,二是e-还原过程.     

玻璃载体TiO2薄层光催化降解久效磷农药

研究了利用TiO₂薄层光催化降解久效磷农药的可行性。结果表明,0.65×10-4mol/L的久效磷经375W中压汞灯照射60min,被完全光催化降解至PO₄3-;加入微量的Fe3++或H2O2可提高久效磷农药的光解率;另外还研究了TiO₂薄层的附着量、反应液初始pH值、空气流量等因素对光催化降解的影响。光照80 h,TiO₂的光催化活性没有减弱,可连续使用。      

TiO2光催化降解PFOA的反应动力学及机制研究

全氟辛酸(PFOA)是一种新的持久性有机污染物,其处置技术是研究的热点.以UV254 nm紫外灯为光源,采用商品TiO2(P25)对PFOA进行光催化降解实验,并考察pH、TiO2用量、初始浓度、反应气氛对降解的影响.结果表明,反应符合准一级动力学方程,pH对反应有重要影响,氧气存在下能提高反应效率.在pH为3,TiO2用量为1.5 g·L-1,通入空气条件下反应7 h实现基本降解,速率常数为0.4206 h-1.投加俘获剂实验表明,空穴(h+)是主要的活性物质,其对反应速率贡献率为66.1%;羟基自由基(·OH)也参与PFOA的降解过程;投加NaF实验表明,PFOA在TiO2上吸附是反应发生的首要条件.UPLC-QTOF/MS分析表明,PFOA光催化降解逐级生成短链全氟羧酸(PFCAs).     

钯掺TiO2光催化降解全氟辛酸

全氟辛酸(perfluorooctanoic acid,PFOA)以其分布广泛性、生物蓄积性、生物毒性强而成为全球关注的一种新型持久性有机污染物.采用化学还原法制备钯掺二氧化钛(Pd-Ti O2)催化剂,利用XRD、FESEM、UV-vis DRS对催化剂进行表征,并考察其在365 nm紫外光照射下对PFOA的光催化降解效果.结果表明,化学还原的制备方法使Ti O2粒径减小、比表面积增大且对紫外光的吸收性能增大,但并不引起PFOA光催化效果的改变.而Pd掺杂后大大增强了PFOA的降解效果,反应7 h后溶液中氟离子浓度为6.62 mg·L-1,是Ti O2(P25)的7.3倍.投加俘获剂与通入氮气的实验证明,在PFOA的降解过程中·OH起重要作用,氧气的存在可促进PFOA的降解.采用UPLC-QTOF-MS对产物进行鉴定分析,PFOA的可能降解过程是经h+氧化后发生脱羧基反应,产生的全氟烷烃自由基(·CnF2n+1)被·OH氧化,脱氟生成短链全氟羧酸.Pd能作为电子(e-)捕获剂、加速e-向O2等电子受体的转移,从而缓解e-累积,提高对PFOA的降解效果.     

光催化氧化法处理染料中间体H酸水溶液

为了去除水中难氧化的有害染料中间体Ｈ酸,研究以ＴＩＯ２、ＺｎＯ、ＣｄＳ和Ｆｅ２Ｏ３为催化剂,采用低压汞灯为光源,对Ｈ酸水溶液进行光催化氧化实验．结果表明：ＴｉＯ２和ＣｄＳ的催化效果最好．采用ＴｉＯ２作催化剂,光催化氧化５ｈ后,Ｈ酸分解率可达９０％,反应速率遵从Ｌａｎｇｍｕｉｒ－Ｈｉｎｓｈｅｌｗｏｏｄ方程,Ｋ＝１２．３Ｌ／ｍｍｏｌ,ｋ＝２５．２×１０－６ｍｏｌ／ｈ．溶液中投加１０ｍｇ／Ｌ的Ｆｅ３＋或Ａｇ＋,可使反应时间缩短２—３ｈ．研究探讨了ｐＨ、ＴｉＯ２投加量和Ｈ酸浓度对催化氧化过程的影响．     

Photocatalytic degradation of carbofuran in TiO2 aqueous solution：Kinetics using design of experiments and mechanism by HPLC/MS/MS

The photocatalytic degradation kinetics of carbofuran was optimized by central composite design based on response surface methodology for the first time. Three variables, TiO2 concentration, initial pH value and the concentration of carbofuran, were selected to determine the dependence of degradation efficiencies on independent variables. Response surface methodology modeling results indicated that the degradation efficiency of carbofuran was highly affected by the initial pH value and the concentration of carbofuran. Then nine degradation intermediates were detected by HPLC/MS/MS. The Frontier Electron Densities of carbofuran were calculated to predict the active sites on carbofuran attacked by hydroxyl radicals and photoholes. Point charges were used to elucidate the chemisorption pattern on TiO2 catalysts during the photocatalytic process. By combining the experimental results and calculation data, the photocatalytic degradation pathways of carbofuran were proposed, including the addition of hydroxyl radicals and the cleavage of the carbamate side chain.     

CuO-TiO2/导电聚合物纤维复合材料的制备及其光催化性能

利用高压静电纺丝技术,制得含羧基的导电聚合物纤维(聚偏氟乙烯/苯乙烯-马来酸酐共聚物/纳米石墨).水热条件下在纤维表面原位合成了纳米级的TiO2,再通过水热法在TiO2表面制备了微米级的球形CuO颗粒,得到CuO-TiO2/导电聚合物纤维复合材料.运用扫描电子显微镜(SEM)、X射线衍射仪(XRD)、紫外-可见吸收光谱仪(UV-Vis)和热失重分析(TGA)对复合材料的结构与性能进行表征,并利用氙灯模拟太阳光进行光催化降解次甲基蓝实验.结果发现,CuO-TiO2/导电聚合物纤维复合材料的降解效率高于CuO-TiO2/非导电聚合物纤维、CuO-TiO2粉体和Degussa P25,光催化降解3.5h时,次甲基蓝的残留率为4.7％.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

四环素光催化降解特性与选择性研究

研究了盐酸四环素的光催化降解行为,结果表明四环素光催化降解反应符合一级反应动力学方程,吸附过程为整个光催化降解的控制步骤,推断四环素的主要降解途径是吸附在二氧化钛(TiO2)表面发生光催化氧化反应.同时,通过对四环素与磺胺甲唑或阿莫西林混合样品的降解实验表明,改变pH、TiO2投加量等因素,两种抗生素的降解表现出了明显的选择性.     

Rubber sheet strewn with TiO2 particles:Photocatalytic activity and recyclability

A new method for the preparation of rubber sheet strewn with titanium dioxide particles (TiO₂-strewn sheet) is presented. This simple and low cost method is based on the use of TiO₂ powder (Degussa P25) being strewn onto the sheet made from rubber latex (60% HA) through a steel sieve. The characteristic of the TiO₂-strewn sheet was studied by using scanning electron microscopy/energy dispersive X-ray spectrometer (SEM/EDS) and X-ray diffractometer (XRD) techniques. The photocatalytic activity of TiO₂-strewn rubber sheet was evaluated using Indigo Carmine (IC) dye as a model for organic dye pollutant in water. The results showed that the TiO₂-strewn sheet could degrade IC dye solution under UV light irradiation. The effects of pH, initial concentration, and the intensity of UV light on the photodegradation were also investigated. Kinetics of the photocatalytic degradation was of the first-order reaction. The used TiO₂-strewn sheet can be recovered and reused. The recycling uses did not require any cleaning between successive uses and no decline in the photodegradation efficiency was observed compared with freshly prepared TiO₂-strewn sheet.     

Ce/TiO2/g-C3N4异质结的制备及光催化降解PFOA反应机制

采用溶胶凝胶-超声混合法制备了铈/二氧化钛/石墨相氮化碳（Ce/TiO₂/g-C₃N₄）异质结催化剂，通过透射电子显微镜（TEM）、X-射线粉末衍射仪（XRD）、傅里叶变换红外光谱仪（FTIR）和紫外-可见分光光度计（UV-Vis）等表征了复合材料的结构、晶相、活性基团和光吸收性能，并考察了可见光下该催化剂对模拟全氟辛酸（PFOA）废水的降解效果.结果表明，Ce/TiO₂/g-C₃N₄分散性好，粒径小于20 nm，金属Ce的掺入及TiO₂/g-C₃N₄异质结的生成，有效抑制了光生电子和空穴对的复合，使复合光催化剂禁带宽度减小，光吸收范围增大，光催化性能得到明显提升.在pH值为2，PFOA浓度为4 mg·L^-1，催化剂投加量为1 g·L^-1的条件下，可见光照射180 min后，可降解94.4%的PFOA，脱氟率为38.6%.降解过程符合准一级反应动力学，速率常数为0.522 h^-1.通过HPLC-MS分析降解产物，同时结合氟元素物料平衡的计算结果，认为降解机制主要是以阴离子形式存在的PFOA吸附至表面带有大量正电荷的催化剂表面后，在光生空穴和活性自由基的作用下，以自由基机理逐步脱去CF₂生成短链的PFCAs，同时生成氟离子.     

氧化剂增强TiO2纤维光催化降解DMF研究

研究TiO₂纤维光催化降解DMF水溶液的结果表明:氧化剂增强了TiO₂纤维对DMF的降解能力,在其它反应条件相同情况下,O₃/TiO₂(F)对DMF降解率是air/TiO₂(F)和H₂O₂/TiO₂(F)的1.5倍左右,且降解速率提高2倍左右,COD分析表明DMF几乎完全矿化.同时实验过程中确定了DMF光催化降解中间产物仲胺的存在.以二甲胺为仲胺代表物进行光催化降解研究表明,中间产物仲胺的迅速降解是O₃增强TiO₂纤维降解效应的主要因素.