Effects of northeast monsoon on trace metal distribution in the South China Sea off Peninsular Malaysia

Concentrations of trace metals in the South China Sea (SCS) were determined off the coast of Terengganu during the months of May and November 2007. The concentrations of dissolved and particulate metals were in the range of 0.019–0.194 μg/L and 50–365 μg/g, respectively, for cadmium (Cd), 0.05–0.45 μg/L and 38–3,570 μg/g for chromium (Cr), 0.05–3.54 μg/L and 21–1,947 μg/g for manganese (Mn), and 0.03–0.49 μg/L and 2–56,982 μg/g for lead (Pb). The order of mean log K _D found was Cd?>?Cr?>?Pb?>?Mn. The study suggests that the primary sources of these metals are discharges from the rivers which drain into the SCS, in particular the Dungun River, which flows in close proximity to agricultural areas and petrochemical industries. During the northeast monsoon, levels of particulate metals in the bottom water samples near the shore were found to be much higher than during the dry season, the probable result of re-suspension of the metals from the bottom sediments.     

Assessing organic contaminant fluxes from contaminated sediments following dam removal in an urbanized river

In this study, methods and approaches were developed and tested to assess changes in contaminant fluxes resulting from dam removal in a riverine system. Sediment traps and passive samplers were deployed to measure particulate and dissolved polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) in the water column prior to and following removal of a small, low-head dam in the Pawtuxet River, an urbanized river located in Cranston, RI, USA. During the study, concentrations of particulate and dissolved PAHs ranged from 21.5 to 103 μg/g and from 68 to 164 ng/L, respectively. Overall, temporal trends of PAHs showed no increases in either dissolved or particulate phases following removal of the dam. Dissolved concentrations of PCBs were very low, remaining below 1.72 ng/L at all sites. Particulate PCB concentrations across sites and time showed slightly greater variability, ranging from 80 to 469 ng/g, but with no indication that dam removal influenced any increases. Particulate PAHs and PCBs were sampled continuously at the site located below the dam and did not show sustained increases in concentration resulting from dam removal. The employment of passive sampling technology and sediment traps was highly effective in monitoring the concentrations and flux of contaminants moving through the river system. Variations in river flow had no effect on the concentration of contaminants in the dissolved or particulate phases, but did influence the flux rate of contaminants exiting the river. Overall, dam removal did not cause measurable sediment disturbance or increase the concentration or fluxes of dissolved or particulate PAHs and PCBs. This is due in large part to low volumes of impounded sediment residing above the dam and highly armored sediments in the river channel, which limited erosion. Results from this study will be used to improve methods and approaches that assess the short- and long-term impacts ecological restoration activities such as dam removal have on the release and transport of sediment-bound contaminants.     

Assessment of the labile fractions of copper and zinc in marinas and port areas in Southern Brazil

The dissolved labile and labile particulate fractions (LPF) of Cu and Zn were analyzed during different seasons and salinity conditions in estuarine waters of marina, port, and shipyard areas in the southern region of the Patos Lagoon (RS, Brazil). The dissolved labile concentration was determined using the diffusive gradients in thin films technique (DGT). DGT devices were deployed in seven locations of the estuary for 72 h and the physicochemical parameters were also measured. The LPF of Cu and Zn was determined by daily filtering of water samples. Seasonal variation of DGT–Cu concentrations was only significant (p?<?0.05) at one shipyard area, while DGT–Zn was significant (p?<?0.05) in every locations. The LPF of Cu and Zn concentrations demonstrated seasonal and spatial variability in all locations, mainly at shipyard areas during high salinity conditions. In general, except the control location, the sampling locations showed mean variations of 0.11–0.45 μg?L^?1 for DGT–Cu, 0.89–9.96 μg?L^?1 for DGT–Zn, 0.65–3.69 μg?g^?1 for LPF–Cu, and 1.35–10.87 μg?g^?1 for LPF–Zn. Shipyard areas demonstrated the most expressive values of labile Cu and Zn in both fractions. Strong relationship between DGT–Zn and LPF–Zn was found suggesting that the DGT–Zn fraction originates from the suspended particulate matter. Water salinity and suspended particulate matter content indicated their importance for the control of the labile concentrations of Cu and Zn in the water column. These parameters must be taken into consideration for comparison among labile metals in estuaries.     

Estuarine mixing behavior of colloidal organic carbon and colloidal mercury in Galveston Bay, Texas

Mercury (Hg) in estuarine water is distributed among different physical phases (i.e. particulate, colloidal, and truly dissolved). This phase speciation influences the fate and cycling of Hg in estuarine systems. However, limited information exists on the estuarine distribution of colloidal phase Hg, mainly due to the technical difficulties involved in measuring it. In the present study, we determined Hg and organic carbon levels from unfiltered, filtered (<0.45 μm), colloidal (10 kDa-0.45 μm), and truly dissolved (<10 kDa) fractions of Galveston Bay surface water in order to understand the estuarine mixing behavior of Hg species as well as interactions of Hg with colloidal organic matter. For the riverine end-member, the colloidal fraction comprised 43 ± 11% of the total dissolved Hg pool and decreased to 17 ± 8% in brackish water. In the estuarine mixing zone, dissolved Hg and colloidal organic carbon showed non-conservative removal behavior, particularly in the low salinity (<15 ppt) region. This removal may be caused by salt-induced coagulation of colloidal matter and consequent removal of dissolved Hg. The particle-water interaction, K(d) ([particulate Hg (mol kg(-1))]/[dissolved Hg (mol L(-1))]) of Hg decreased as particle concentration increased, while the particle-water partition coefficient based on colloidal Hg and the truly dissolved Hg fraction, K(c) ([colloidal Hg (mol kg(-1))]/[truly dissolved Hg (mol L(-1))]) of Hg remained constant as particle concentration increased. This suggests that the particle concentration effect is associated with the amount of colloidal Hg, increasing in proportion to the amount of suspended particulate matter. This work demonstrates that, colloidal organic matter plays an important role in the transport, particle-water partitioning, and removal of dissolved Hg in estuarine waters.     

Evaluation of airborne lead levels in storage battery workshops and some welding environments in Kumasi metropolis in Ghana

Airborne lead levels were assessed in nine workshops, three each from battery, electronic repair, and welding sources within the Kumasi Metropolis in Ghana. Samples were collected at 0, 2.5, and 5.0 m away from the emission source at the workshops during working hours and another at 5.0 m during break hours. Airborne lead particulates were collected and analyzed using the filter membrane technique and flame atomic absorption spectrophotometry, respectively. There were significant differences (p ≤ 0.05) among the air lead levels from the workshops. Workshop 3b produced the highest significant values of air lead concentrations of 2,820.31 ± 53.89, 2,406.74 ± 71.87, 754.55 ± 72.52, and 549.01 ± 67.30 μg/m³ at distances of 0, 2.5, 5.0, and 5.0 m (break-time measurement), respectively, while workshop 1w significantly produced the lowest air lead concentration values of 261.06 ± 21.60, 190.92 ± 36.90, 86.43 ± 16.26, and 61.05 ± 3.88 μg/m³ at distances of 0, 2.5, 5.0, and 5.0 m (break-time measurement), respectively. The air lead levels reduced with distance from emission source at the workshops. At all the distances of measurement at working hours, the airborne lead levels were higher than the World Health Organization standard of 50 μg/m³ and exceeded the threshold limit values of 100 to 150 μg/m³ recommended in most jurisdictions. Workers and people in the immediate environs were exposed to air lead levels that were too high by most international standards, thus posing a serious threat to their health.     

乌鲁木齐市可吸入颗粒物水溶性离子特征及来源解析

采暖期时在乌鲁木齐市采集了环境空气中的可吸入颗粒物,对可吸入颗粒物质量浓度及8种水溶性离子的特征和来源进行了分析。结果表明,细粒子和粗粒子的月平均质量浓度分别是53.5～233.3μg/m3和38.9～60.9μg/m3;细粒子和粗粒子中水溶性离子主要由SO24-、NH4+和NO3-组成;粗粒子中NH4+与NO3-和SO24-的相关性分别是0.70和0.66,细粒子中NH4+与NO3-和SO24-的相关性分别是0.89和0.93,铵盐是乌鲁木齐可吸入颗粒物主要存在形式;煤烟尘是乌鲁木齐市采暖期可吸入颗粒物的主要来源。     

Application of zirconium–iridium permanent modifier for the simultaneous determination of lead, cadmium, arsenic, and nickel in atmospheric particulate matter by multi-element electrothermal atomic absorption spectrometry

A novel and robust method for the simultaneous determination of lead, cadmium, arsenic, and nickel in atmospheric particulate matter by multi-element electrothermal atomic absorption spectrometry was developed, using zirconium–iridium coating as permanent modifier (140 μg Zr and 4 μg Ir). After 300 atomization cycles, it was necessary to add 2 μg of Ir. Due to the varying concentrations of Pb in atmospheric particulate matter, lead was monitored at two wavelengths, at the less sensitive line of 261.4 nm for high concentration samples (>20 μg?L^?1) or at 283.3 nm for the low concentration samples. Matrix-matched calibration had to be performed for quantitative recoveries (96–102 %). Following this approach, the four elements were determined in atmospheric particulate matter samples from an industrial area near the city of Athens in two different time periods (cold–warm) with limits of detection of 5.5 ng?m^?3 for Pb at 261.4 nm and 0.29 ng?m^?3 at 283.3 nm, 0.019 ng?m^?3 for Cd, 0.14 ng?m^?3 for As, and 0.22 ng?m^?3 for Ni. Lead, Cd, and As levels were very low, whereas Ni content was at comparable levels with other areas worldwide.     

Assessment of indoor and outdoor particulate air pollution at an urban background site in Iran

The relationship between indoor and outdoor particulate air pollution was investigated at an urban background site on the Payambar Azam Campus of Mazandaran University of Medical Sciences in Sari, Northern Iran. The concentration of particulate matter sized with a diameter less than 1 μm (PM_1.0), 2.5 μm (PM_2.5), and 10 μm (PM₁₀) was evaluated at 5 outdoor and 12 indoor locations. Indoor sites included classrooms, corridors, and office sites in four university buildings. Outdoor PM concentrations were characterized at five locations around the university campus. Indoor and outdoor PM measurements (1-min resolution) were conducted in parallel during weekday mornings and afternoons. No difference found between indoor PM₁₀ (50.1 ± 32.1 μg/m³) and outdoor PM₁₀ concentrations (46.5 ± 26.0 μg/m³), indoor PM_2.5 (22.6 ± 17.4 μg/m³) and outdoor PM_2.5 concentration (22.2 ± 15.4 μg/m³), or indoor PM_1.0 (14.5 ± 13.4 μg/m³) and outdoor mean PM_1.0 concentrations (14.2 ± 12.3 μg/m³). Despite these similar concentrations, no correlations were found between outdoor and indoor PM levels. The present findings are not only of importance for the potential health effects of particulate air pollution on people who spend their daytime over a period of several hours in closed and confined spaces located at a university campus but also can inform regulatory about the improvement of indoor air quality, especially in developing countries.     

Analysis of elemental concentration using ICP-AES and pathogen indicator in drinking water of Qasim Abad, District Rawalpindi, Pakistan

The present study was conducted to investigate drinking water quality (groundwater) from water samples taken from Qasim Abad, a locality of approximately 5,000 population, situated between twin cities Rawalpindi and Islamabad in Pakistan. The main sources of drinking water in this area are water bores which are dug upto the depth of 250–280 ft in almost every house. The study consists of the determination of physico-chemical properties, trace metals, heavy metals, rare earth elements and microbiological quality of drinking water. The data showed the variation of the investigated parameters in samples as follows: pH 6.75 to 8.70, electrical conductivity 540 to 855 μS/cm, total dissolved solids 325.46 to 515.23 ppm and dissolved oxygen 1.50 to 5.64 mg/L which are within the WHO guidelines for drinking water quality. The water samples were analysed for 30 elements (aluminium, iron, magnesium, manganese, silicon, zinc, molybdenum, titanium, chromium, nickel, tungsten, silver, arsenic, boron, barium, beryllium, cadmium, cobalt, copper, gallium, mercury, lanthanum, niobium, neodymium, lead, selenium, samarium, tin, vanadium and zirconium) by using inductively coupled plasma atomic emission spectroscopy. The organic contamination was detected in terms of most probable number (MPN) of faecal coliforms. Overall, elemental levels were lower than the recommended values but three water bores (B-1, B-6, B-7) had higher values of iron (1.6, 2.206, 0.65 ppm), two water bores (B-1, B-6) had higher values of aluminium (0.95, 1.92 ppm), respectively, and molybdenum was higher by 0.01 ppm only in one water bore (B-11). The total number of coliforms present in water samples was found to be within the prescribed limit of the WHO except for 5 out of 11 bore water samples (B-2, B-3, B-4, B-8, B-11), which were found in the range 5–35 MPN/100 mL, a consequence of infiltration of contaminated water (sewage) through cross connection, leakage points and back siphoning.     

Investigations on boron levels in drinking water sources in China

To evaluate boron contamination of public drinking water in China, both dissolved and total boron contents in 98 public drinking water sources from 49 cities, 42 brands of bottled water samples from supermarkets in several cities, and 58 water samples from boron industrial area were measured by inductively coupled plasma-mass spectrometry (ICP-MS). Our experimental results showed that boron existed in public drinking water sources mainly in dissolved status with total concentrations ranging from 0.003 to 0.337 mg/L (mean = 0.046 mg/L). The mean boron concentrations in mineral and pure bottled water were 0.052 and 0.028 mg/L, respectively. The results obtained in this work showed that there was no health risk on view of boron in public drinking water sources and bottled water. In boron industrial area, boron concentrations in surface water and ground water were 1.28 mg/L (range = 0.007–3.8 mg/L) and 18.3 mg/L (range = 0.015–140 mg/L), respectively, which indicated that boron industry caused boron pollution in local water system.     

Perchlorate contamination of groundwater from fireworks manufacturing area in South India

Perchlorate contamination was investigated in groundwater and surface water from Sivakasi and Madurai in the Tamil Nadu State of South India. Sensitive determination of perchlorate (LOQ?=?0.005 μg/L) was achieved by large-volume (500 μL) injection ion chromatography coupled with tandem mass spectrometry. Concentrations of perchlorate were <0.005–7,690 μg/L in groundwater (n?=?60), <0.005–30.2 μg/L in surface water (n?=?11), and 0.063–0.393 μg/L in tap water (n?=?3). Levels in groundwater were significantly higher in the fireworks factory area than in the other locations, indicating that the fireworks and safety match industries are principal sources of perchlorate pollution. This is the first study that reports the contamination status of perchlorate in this area and reveals firework manufacture to be the pollution source. Since perchlorate levels in 17 out of 57 groundwater samples from Sivakasi, and none from Madurai, exceeded the drinking water guideline level proposed by USEPA (15 μg/L), further investigation on human health is warranted.     

Excitation–emission matrices applied to the study of urban effluent discharges in the Chubut River (Patagonia, Argentina)

Natural and contaminated waters of the final reaches of the Chubut River (Patagonia, Argentina) were studied to obtain information about river organic matter and effects of domestic and industrial discharges (fishery effluents and sewages). Fluorescence Excitation–Emission Matrices (EEMs) were obtained from samples only filtered (0.45 μm) and diluted, if necessary, to avoid the inner filter effect. In addition, physicochemical parameters were measured to know the quality of the water and the effluents. Results show that EEMs allow a rapid and simple control of the effluents from fisheries and domestic sewage in Chubut River estuary, necessary to take management decisions.     

Blood levels of cadmium and lead in residents near abandoned metal mine areas in Korea

We analyzed national data on blood lead levels (BLL) and blood cadmium levels (BCL) in residents living near 38 abandoned metal mining areas (n?=?5,682, 18–96 years old) in Korea that were collected by the first Health Effect Surveillance for Residents in Abandoned Metal mines (HESRAM) from 2008 to 2011. The geometric mean BCL and BLL were 1.60 μg/L (95 % CI?=?1.57–1.62 μg/L) and 2.87 μg/dL (95 % CI?=?2.84–2.90 μg/dL), respectively, notably higher than levels in the general population in Korea and other countries. We found significantly higher BLL and BCL levels in people living within 2 km of an abandoned metal mine (n?=?3,165, BCL?=?1.87 μg/L, BLL?=?2.91 μg/dL) compared to people living more than 2 km away (n?=?2,517, BCL?=?1.31 μg/L, BLL?=?2.82 μg/dL; P?<?0.0001) and to the general population values reported in the literature.     

Iodide-assisted total lead measurement and determination of different lead fractions in drinking water samples

Lead and its compounds are toxic and can harm human health, especially the intelligence development in children. Accurate measurement of total lead present in drinking water is crucial in determining the extent of lead contamination and human exposure due to drinking water consumption. The USEPA method for total lead measurement (no. 200.8) is often used to analyze lead levels in drinking water. However, in the presence of high concentration of the tetravalent lead corrosion product PbO(2), the USEPA method was not able to fully recover particulate lead due to incomplete dissolution of PbO(2) particles during strong acid digestion. In this study, a new procedure that integrates membrane separation, iodometric PbO(2) measurement, strong acid digestion and ICP-MS measurement was proposed and evaluated for accurate total lead measurement and quantification of different lead fractions including soluble Pb(2+), particulate Pb(II) carbonate and PbO(2) in drinking water samples. The proposed procedure was evaluated using drinking water reconstituted with spiked Pb(2+), spiked particulate Pb(II) carbonate and in situ formed or spiked PbO(2). Recovery tests showed that the proposed procedure and the USEPA method can achieve 93-112% and 86-103% recoveries respectively for samples containing low PbO(2) concentrations (0.018-0.076 mg Pb per L). For samples containing higher concentrations of PbO(2) (0.089-1.316 mg Pb per L), the USEPA method failed to meet the recovery requirement for total lead (85-115%) while the proposed method can achieve satisfactory recoveries (91-111%) and differentiate the soluble Pb(2+), particulate Pb(II) carbonate and PbO(2).     

Atmospheric aerosols at a regional background Himalayan site—Mukteshwar, India

Continuous aerosol measurements were made at a regional background station (Mukteshwar) located in a rural Himalayan mountain terrain from December 2005 to December 2008 for a period of 3 years. The average concentrations of particulate matter less than or equal to 10 μm (PM₁₀), particulate matter less than or equal to 2.5 μm (PM_2.5) and black carbon (BC) are 46.0, 26.6 and 0.85 μg/m³ during the study period. Majority of the PM₁₀ values lie below 100 μg/m³ while majority of the PM_2.5 values lie below 30 μg/m³. It is further seen that during the monsoon months, especially July and August, the average values are comparatively low. It is also noted that the PM_2.5/PM₁₀ ratios between 0.50 and 0.75 have the maximum frequency distribution in the data set. Furthermore, the monthly mean ratio of BC to PM_2.5 mass lies between 3.0 and 7.5 % during the study period. Though the average PM₁₀ and PM_2.5 concentrations during the study period are less than the respective Indian ambient air quality standards, however, they are still above the WHO guidelines and would have adverse health impacts. This shows that even in rural/background regions that are far away from major pollution sources or urban areas, the aerosol concentrations are significant and require long-term monitoring, source quantification and aerosol model simulations.     

Occurrence and sorption properties of arsenicals in marine sediments

The content of total arsenic, the inorganic forms: arsenite (As(III)) and arsenate (As(V)), the methylated forms: monomethylarsonic acid and dimethylarsinic acid (DMA), trimethylarsenic oxide, tetramethylarsenonium ion and arsenobetaine was measured in 95 sediment samples and 11 pore water samples from the Baltic Sea near the island of Bornholm at depths of up to 100 m. As(III+V) and DMA were detected in the sediment and As(III+V) was detected in the sediment pore water. Average total As concentration of 10.6?±?7.4 mg/kg dry matter (DM) in the sediment corresponds to previously reported values in the Baltic Sea and other parts of the world. Existing data for on-site measurements of sorption coefficients (Kd) of arsenicals in marine and freshwater sediments show large variability from <1 to >1,000 L/kg. In this work, calculated sorption coefficients (Kd and Koc) for As(III+V) showed significant correlation with depth, dissolved oxygen (DO), salinity and sediment classification; for depths <70 m, salinity <11 %, DO >9 mg/L and sand/silt/clay sediments the Kd was 118?±?76 L/kg DM and for depths >70 m, salinity >11 %, DO?<?9 mg/L and muddy sediments the Kd was 513?±?233 L/kg DM. The authors recommend using the found Kd value for arsenic in marine sediments when conditions are similar to the Baltic Sea. At locations with significant anthropogenic point sources or where the local geology contains volcanic rock and sulphide mineral deposits, there may be significantly elevated arsenic concentrations, and it is recommended to determine on-site Kd values.     

Spectrophotometric determination of platinum(IV) in alloys, complexes, environmental, and pharmaceutical samples using 4-[N,N-(diethyl)amino] benzaldehyde thiosemicarbazone

4-[N,N-(Diethyl)amino] benzaldehyde thiosemicarbazone (DEABT) is proposed as an analytical reagent for the spectrophotometric determination of platinum(IV). The DEABT forms 1:2 yellow complex with Pt(IV), which is sparingly soluble in water and completely soluble in water–ethanol–DMF medium. The Pt(IV)–DEABT complex shows maximum absorbance at 405 nm. Beer’s law is valid up to 7.80 μg cm^???3, and optimum concentration range for the determination of platinum(IV) is 0.48–7.02 μg cm^???3. The molar absorptivity and Sandell’s sensitivity of the method are found to be 1.755 × 10⁴ dm³ mol^???1 cm^???1 and 0.0012 μg cm^???2, respectively. The relative error and coefficient of variation (n?=?6) for the method does not exceed ±0.43% and 0.35%, respectively. Since the method tolerates a number of metal ions commonly associated with platinum, it can be employed for the determination of platinum in environmental samples, pharmaceutical samples, alloys, catalysts, and complexes. The method is rapid as the Pt(IV)–DEABT complex is soluble in water–ethanol–DMF medium and not requiring any time consuming extraction method for the complex.     

Identification and quantification of 19 pharmaceutical active compounds and metabolites in hospital wastewater in Cameroon using LC/QQQ and LC/Q-TOF

Human pharmaceutical residues are a serious environmental concern. They have been reported to have eco, geno, and human toxic effects, and thus their importance as micropollutants cannot be ignored. These have been studied extensively in Europe and North America. However, African countries are still lagging behind in research on these micropollutants. In this study, the wastewaters of the University Teaching Hospital of Yaoundé (UTHY) were screened for the presence of active pharmaceutical ingredients and their metabolites. The screening was carried out using two methods: high-performance liquid chromatography coupled to a triple quadrupole analyzer (LC/QQQ) and high-performance coupled to a mass spectrometer with a time of flight analyzer (LC/Q-TOF). A total of 19 active pharmaceutical ingredients and metabolites were identified and quantified. The compounds identified include paracetamol (211.93 μg/L), ibuprofen (141 μg/L), tramadol (76 μg/L), O-demethyltramadol (141 μg/L), erythromycinanhydrate (7 μg/L), ciprofloxacin (24 μg/L), clarinthromycine (0.088 μg/L), azitromycine (0.39 μg/L), sulfamethoxazole 0.16 μg/L), trimetoprime (0.27 μg/L), caffeine (5.8 μg/L), carnamaeepine (0.94 μg/L), atenolol (0.43 μg/L), propranolol (0.3 μg/L), cimetidine (34 μg/L), hydroxy omeprazole (5 μg/L), diphenhydramine (0.38 μg/L), metformine (154 μg/L), and sucralose (13.07 μg/L).     

The impact of station location on water quality characterization in the Loxahatchee National Wildlife Refuge

Water quality was monitored in the Loxahatchee National Wildlife Refuge based on the Consent Decree (CDN), the Enhanced Refuge (ERN), the four-part Test impacted (FPTIN), and the four-part test unimpacted (FPTUN) networks. Alkalinity, dissolved organic carbon, total organic carbon, dissolved oxygen, total dissolved solids, total suspended solids, turbidity, pH, specific conductivity, calcium, chloride, silicon, sulfate, and total phosphorus (TP) were measured from 2005 through 2009. When the ERN was used, the 10 μg TP L^?1 Consent Decree limit would have been exceeded and would have ranged from a low of 2 months in 2009 to a high of 9 months in 2005. Based on the CDN, the limit exceeded only for 1 month in each year from 2006 through 2008. Based on the FPTIN, the 10 μg TP L^?1 limit would have been exceeded and would have ranged from a low of 1 month in 2007 to a high of 7 months in 2005 and 2008. Based on the CDN, the limit only exceeded for 1 month in each year from 2006 through 2008. Since TP is rapidly removed from canal water intruded into the Refuge marsh, one cannot expect a water quality sampling station located 2 km from the source to reliably detect violations. This may be the primary reason why there have been very few months when TP concentration has exceeded the limit since 1992 or part four of the four-part test annual 15 μg?L^?1 limit since 2006.     

Mercury concentrations in fish from a Sierra Nevada foothill reservoir located downstream from historic gold-mining operations

This study examined mercury concentrations in whole fish from Camp Far West Reservoir, an 830-ha reservoir in northern California, USA, located downstream from lands mined for gold during and following the Gold Rush of 1848–1864. Total mercury (reported as dry weight concentrations) was highest in spotted bass (mean, 0.93 μg/g; range, 0.16–4.41 μg/g) and lower in bluegill (mean, 0.45 μg/g; range, 0.22–1.96 μg/g) and threadfin shad (0.44 μg/g; range, 0.21–1.34 μg/g). Spatial patterns for mercury in fish indicated high concentrations upstream in the Bear River arm and generally lower concentrations elsewhere, including downstream near the dam. These findings coincided with patterns exhibited by methylmercury in water and sediment, and suggested that mercury-laden inflows from the Bear River were largely responsible for contaminating the reservoir ecosystem. Maximum concentrations of mercury in all three fish species, but especially bass, were high enough to warrant concern about toxic effects in fish and consumers of fish.