Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Photocatalytic degradation of cellulose bleaching effluent by supported TiO2 and ZnO

A cellulose bleaching effluent (E1) was degraded in batch conditions by photocatalysis using TiO2 and ZnO supported on glass Raschig rings. The effluent was completely decolourised and the total phenol content was reduced by 85% after 120 min treatment with both catalysts. Partial mineralization of the organic matter was confirmed by total organic carbon (TOC) reduction, approximately 50%. The residual organic matter shows a low acute toxicity as compared to the initial values and AOX values are strongly reduced after the photocatalytic oxidation. Molecular mass distribution showed that high molecular mass compounds were almost completely degraded.     

Degradation and toxicity reduction of textile effluent by combined photocatalytic and ozonation processes

To minimize the environmental impact of textile effluents, mainly related to their high coloration and the presence of toxic or carcinogenic reactive dyes, the efficiency of photochemical and ozonation processes, applied in the form of isolated and combined procedures, were evaluated. The investigation was focused on the reduction of total organic carbon content (TOC), color and acute toxicity (monitoring by inhibition of Escherichia coli respiration). For a reaction time of 60 min, the anatase TiO2-assisted photocatalytic process produces color and TOC reduction of about 90% and 50%, respectively. Meanwhile, the ozonation process gives a decolorization of about 60% but negligible TOC reduction. When the processes were applied in a simultaneous form, the decolorization was almost complete and the TOC reduction was higher than 60%. The three treatments studied yield an acute toxicity reduction of around 50%.     

Toxicity of nanosized and bulk ZnO, CuO and TiO2 to bacteria Vibrio fischeri and crustaceans Daphnia magna and Thamnocephalus platyurus

As the production of nanoparticles of ZnO, TiO2 and CuO is increasing, their (eco)toxicity to bacteria Vibrio fischeri and crustaceans Daphnia magna and Thamnocephalus platyurus was studied with a special emphasis on product formulations (nano or bulk oxides) and solubilization of particles. Our innovative approach based on the combination of traditional ecotoxicology methods and metal-specific recombinant biosensors allowed to clearly differentiate the toxic effects of metal oxides per se and solubilized metal ions. Suspensions of nano and bulk TiO2 were not toxic even at 20 g l(-1). All Zn formulations were very toxic: L(E)C50 (mg l(-1)) for bulk ZnO, nanoZnO and ZnSO4.7H2O: 1.8, 1.9, 1.1 (V. fischeri); 8.8, 3.2, 6.1 (D. magna) and 0.24, 0.18, 0.98 (T. platyurus), respectively. The toxicity was due to solubilized Zn ions as proved with recombinant Zn-sensor bacteria. Differently from Zn compounds, Cu compounds had different toxicities: L(E)C50 (mg l(-1)) for bulk CuO, nano CuO and CuSO4: 3811, 79, 1.6 (V. fischeri), 165, 3.2, 0,17 (D. magna) and 95, 2.1, 0.11 (T. platyurus), respectively. Cu-sensor bacteria showed that toxicity to V. fischeri and T. platyurus was largely explained by soluble Cu ions. However, for Daphnia magna, nano and bulk CuO proved less bioavailable than for bacterial Cu-sensor. This is the first evaluation of ZnO, CuO and TiO2 toxicity to V. fischeri and T. platyurus. For nano ZnO and nano CuO this is also a first study for D. magna.     

TiO2光催化氧化降解乳酸的工艺及机理研究

以TiO2为催化剂、紫外灯为光源对乳酸进行光催化降解实验,考察了乳酸初始浓度、TiO2用量、反应时间、曝气方式等因素对乳酸降解率的影响,并在此基础上应用正交实验对降解条件进行优化,同时对乳酸的降解机理进行了探索研究。实验结果表明：以300 W紫外汞灯为光源,在乳酸初始浓度为0.5 g/L、TiO2量为0.20 g/L、反应时间120 min、持续通入空气鼓泡的条件下,乳酸降解效果最佳,乳酸降解率为99.9%;降解12 h总有机碳去除率达91.2%。乳酸光催化降解的反应途径为：乳酸脱羧生成乙醇,乙醇被氧化生成乙醛,进而氧化为乙酸,所有的中间产物被继续降解,最终矿化为CO2和H2O等小分子物质。     

Sequential treatment via Trametes versicolor and UV/TiO2/Ru(x)Se(y) to reduce contaminants in waste water resulting from the bleaching process during paper production

An efficient sequential, biological and photocatalytic treatment to reduce the pollutant levels in wastewater due to the bleaching process during paper production is reported. For a biological pre-treatment, 800 ml of non-sterilized effluent was inoculated with Trametes versicolor immobilized in polyurethane foam, with 25 g l(-1) glucose, 6.75 mM CuSO(4), and 0.22 mM MnSO(4) added, and cultured at 25 degrees C with an air flow of 800 ml min(-1) for 8d. The fungus did not inhibit growth of the heterotropic populations of the effluent. After 4d of culture, the chemical oxygen demand (COD) reduction and colour removal (CR) were 82% and 80%, respectively, with laccase (LAC) and manganese peroxidase (MnP) activities of 345 U l(-1) and 78 U l(-1), respectively. The COD reduction and CR correlated positively (p<0.0001) with LAC and MnP activities. Chlorophenol removal was 99% of pentachlorophenol, 99% of 2,3,4,6-tetrachlorophenol (2,3,4,6-TCP), 98% of 3,4-dichlorophenol (3,4-DCP) and 77% of 4-chlorophenol (4-CP), while 2,4,5-trichlorophenol (2,4,5-TCP) increased to 0.2 mg l(-1). The pre-treated effluent was then exposed to a photocatalytic treatment. The treatment with photolysis resulted in 9% CR and 46% COD reduction, 42% CR and 60% COD reduction by photocatalysis, and 62% CR and 85% COD reduction by heterogeneous photocatalysis with the system TiO(2)/Ru(x)Se(y) (Fig. 4). With this treatment the bacterial and fungal populations also decreased by 5 logarithmic units with respect to the biological treatment alone (Fig. 5). The total sequential treatment resulted in a 92% CR (from 5800 UC), 97% COD reduction (from 59 g l(-1)) and 99% chlorophenol removal at 96 h and 20 min.     

Degradation of nitrogen containing organic compounds by combined photocatalysis and ozonation

The combination of TiO2-assisted photocatalysis and ozonation in the degradation of nitrogen-containing substrates such as alkylamines, alkanolamines, heterocyclic and aromatic N-compounds has been investigated. A laboratory set-up was designed and the influence of the structure of the N-compound, the TiO2 and ozone concentration on the formation of breakdown products were examined. The experimental results showed that a considerable increase in the degradation efficiency of the N-compounds is obtained by a combination of photocatalysis and ozonation as compared to either ozonation or photocatalysis only. The mineralization of the model substances was monitored by measurements of the TOC and ion-chromatographic determinations of the formed NO2- and NO3-. The temporal changes of concentrations of breakdown products, such as NH4+, short chain alkyl- and alkanolamines were determined by single column ion chromatography (SCIC) and as well as by electrospray mass spectrometry (EI-MS).     

The direct photolysis and photocatalytic degradation of alachlor at different TiO2 and UV sources

Direct photolysis and photocatalytic degradations of alachlor, a widely used herbicide, were studied using three different monochromatic UV lamps (254, 300 and 350 nm) and two TiO(2) sources. Both the direct photolysis and photocatalytic degradations of alachlor follow pseudo-first-order decay kinetics. TiO(2)-P25 was found to be an effective photocatalyst compared to TiO(2)-BDH. The direct photolysis of alachlor was dominant at 254 nm even if TiO(2) was present in the solution. Among the three UV wavelengths used, the highest photocatalysis quantum yield was obtained at 300 nm. The photocatalytic degradation rate of alachlor increased with the dosages of TiO(2), but an overdose of TiO(2) would retard the reaction due to light attenuation. Photocatalytic reactions were slightly enhanced in an alkaline medium, and the different proton sources causing various degrees of rate retardation were due to the presence of the corresponding counter anions. This effect was diminished at a later stage after the reaction intermediates were formed.     

Titanium dioxide mediated photocatalytic degradation of monochlorobenzene in aqueous phase

The reaction sequence for the photocatalytic degradation of monochlorobenzene (MCB) in UV/TiO2 process, including substrate adsorption, degradation, and mineralization, was studied. The theoretical maximum quantity of MCB that could be adsorbed onto TiO2 surface in aqueous phase was 0.18+/-0.04 micromol m(-2) of TiO2. In accordance with the upper limit of the relative surface coverage of MCB molecules to surface hydroxyls of TiO2 was around 2.2%, the water molecules as the major adjacent species near TiO2 surface would compete with MCB molecules. Increasing the initial substrate concentration to an appropriate value or enhancing the affinity between the MCB and the TiO2 surface by adjusting the solution pH would promote the photocatalytic degradation. Experimental results revealed that the neutral medium was beneficial for the degradation of MCB. In comparison, the mineralization was most improved at acidic condition. Generally, 90% of the total organic carbon (TOC) was mineralized after 240 min illumination time in the examined pH range except solution pH 11. The suppressed mineralization of MCB at solution pH 11 was ascribed to the lack of adsorption. A simplified 2-step consecutive kinetic model was used to simulate the mineralization.     

Decolorization and biodegradability of photocatalytic treated azo dyes and wool textile wastewater

The photodegradation and biodegradability have been investigated for four non-biodegradable commercial azo dyes, Reactive YellowKD-3G, Reactive Red 15, Reactive Red 24, Cationic Blue X-GRL, an indicator. Methyl Orange, and one industrial wool textile wastewater, using TiO2 suspensions irradiated with a medium pressure mercury lamp. The color removal of dyes solution and dyeing wastewater reached to above 90% within 20-30 min. of photocatalytic treatment. Biochemical oxygen demand (BOD) was found to increase, while chemical oxygen demand (COD), total organic carbon (TOC) decreased, so that the ratio of BOD5/COD of the wastewater increased from original zero up to 0.75. The result implies that photocatalytic oxidation enhanced the biodegradability of the dye-containing wastewater and therefore relationship between decolorization and biodegradability exists. When the color disappeared completely, the wastewater biodegraded normally and could be discharged for further treatment. The experimental results demonstrate that it is possible to combine photocatalysis with conventional biological treatment for the remedy of wastewater containing generally non-biodegradable azo dyes.     

Effect of ZnFe2O4 doping on the photocatalytic activity of TiO2

The photocatalytic oxidation of the organic pollutants with the TiO2 as photocatalyst has been widely studied in the world, and many achievements have been got. The degradation of pollutants is highly related with the photocatalytic activity of TiO2. It is demonstrated that doping ions or oxides to TiO2 is one way to enhance the photocatalytic activity of TiO2. In this paper, the ZnFe2O4-doped TiO2 nanoparticles were prepared from butyl titanate by a sol-gel method and characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results showed that when TiO2 was doped with ZnFe2O4, its particle size will decrease and its crystal structure will partly transform from anatase to rutile. The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that doping ZnFe2O4 to TiO2 will enhance the photocatalytic activity of TiO2 and that ZnFe2O4-doped TiO2 in the coexistence of anatase and rutile has higher efficiency for the degradation of Rhodamine B than that in the anatase phase alone. Also the different role of O2 in the direct photolysis and photocatalysis of Rhodamine B was discussed.     

Hydrogen peroxide photolysis, fenton reagent and photo-fenton for the degradation of nitrophenols: a comparative study

The kinetics of the degradation of seven nitrophenols (2-nitrophenol, 4-nitrophenol, 2,5-dinitrophenol, 2,6-dinitrophenol, 2,4-dinitrophenol, 2-methyl-4,6-dinitrophenol, 4-methyl-2,6-dinitrophenol) with the Fenton reagent, photo-Fenton, and hydrogen peroxide photolysis was investigated. The efficiency and operating costs for the studied treatments were evaluated and compared. The Fenton reagent was found to be the most efficient and the cheapest way for the nitrophenols (NPs) degradation. The formation of nitrate as a result of mineralisation of organically bounded nitrogen was observed during the treatment of NPs with studied treatment processes. The degrees of organically bounded nitrogen conversion to nitrate after 90% degradation of NPs with the Fenton, photo-Fenton and hydrogen peroxide photolysis were 51-67%, 85-90%, and 50-60%, respectively. According to Daphnia magna acute toxicity test, the Fenton treatment led to complete detoxification of NPs.     

Photoassisted and photocatalytic degradation of sulfur mustard using TiO2 nanoparticles and polyoxometalates

The decomposition of highly toxic chemical warfare agent, sulfur mustard (bis(2-chloroethyl) sulfide or HD), has been studied by homogeneous photolysis and heterogeneous photocatalytic degradation on titania nanoparticles. Direct photolysis degradation of HD with irradiation system was investigated. The photocatalytic degradation of HD was investigated in the presence of TiO₂ nanoparticles and polyoxometalates embedded in titania nanoparticles in liquid phase at room temperature (33?±?2 °C). Degradation products during the treatment were identified by gas chromatography–mass spectrometry. Whereas apparent first-order kinetics of ultraviolet (UV) photolysis were slow (0.0091 min^?1), the highest degradation rate is obtained in the presence of TiO₂ nanoparticles as nanophotocatalyst. Simultaneous photolysis and photocatalysis under the full UV radiation leads to HD complete destruction in 3 h. No degradation products observed in the presence of nanophotocatalyst without irradiation in 3 h. It was found that up to 90 % of agent was decomposed under of UV irradiation without TiO₂, in 6 h. The decontamination mechanisms are often quite complex and multiple mechanisms can be operable such as hydrolysis, oxidation, and elimination. By simultaneously carrying out photolysis and photocatalysis in hexane, we have succeeded in achieving faster HD decontamination after 90 min with low catalyst loading. TiO₂ nanoparticles proved to be a superior photocatalyst under UV irradiation for HD decontamination.     

Sonophotocatalytic degradation of alazine and gesaprim commercial herbicides in TiO2 slurry

The photocatalytic degradation of alazine and gesaprim commercial herbicides was carried out in aqueous TiO(2) suspensions under UV light (15W, 352 nm). Degradation of these herbicides was also observed by the combined effects of photocatalysis with sonolysis (sonophotocatalysis) using an ultrasound source of 20kHz. Degradation profiles were recorded by measuring the concentration of the active compounds present in the alazine (alachlor and atrazine) and gesaprim (atrazine) by HPLC as a function of irradiation time (sound and/or light). Over 90% of the active component in the gesaprim was abated and those in alazine were completely degraded. The content of total organic carbon and chemical oxygen demand was also monitored. Mineralization of the commercial herbicides was achieved. Over 80% of chemical oxygen demand abatement was attained for both herbicides with sonophotocatalysis at 150 min of irradiation time. The photocatalytic degradation of the herbicides followed a pseudo-first order kinetics and their rate constant was increased by the combined effects of sonolysis.     

Influence of sediment on the fate and toxicity of a polyethoxylated tallowamine surfactant system (MON 0818) in aquatic microcosms

The fate and toxicity of a polyethoxylated tallowamine (POEA) surfactant system, MON 0818, was evaluated in water-sediment microcosms during a 4-d laboratory study. A surfactant solution of 8 mg l(-1) nominal concentration was added to each of nine 72-l aquaria with or without a 3-cm layer of one of two natural sediments (total organic carbon (TOC) 1.5% or 3.0%). Control well water was added to each of nine additional 72-l aquaria with or without sediment. Water samples were collected from the microcosms after 2, 6, 24, 48, 72, and 96 h of aging to conduct 48-h toxicity tests with Daphnia magna and to determine surfactant concentrations. Elevated mortality of D. magna (43-83%) was observed in overlying water sampled from water-only microcosms throughout the 96-h aging period, whereas elevated mortality (23-97%) was only observed in overlying water sampled from water-sediment microcosms during the first 24h of aging. Measured concentrations of MON 0818 in water-only microcosms remained relatively constant (4-6 mg l(-1)) during the 96-h period, whereas the concentrations in overlying water from microcosms containing either of the two types of sediment dissipated rapidly, with half-lives of 13 h in the 3.0% TOC sediment and 18 h in the 1.5% TOC sediment. Both toxicity and the concentration of MON 0818 in overlying water decreased more rapidly in microcosms containing sediment with the higher percent TOC and clay and with a higher microbial biomass. Mortality of D. magna was significantly correlated with surfactant concentrations in the overlying water. These results indicate that the toxicity of the POEA surfactant in water rapidly declines in the presence of sediment due to a reduction in the surfactant concentration in the overlying water above the sediment.     

Aqueous photolysis of tetracycline and toxicity of photolytic products to luminescent bacteria

The extensive utilization of antibiotics in the pharmaceutical therapies and agricultural husbandry has led to the worldwide pollution in environments. In this study the photolysis behaviors of tetracycline (TC) and toxicity of its degradation products were investigated. The results showed that TC photolysis followed first-order kinetics. The photolysis rate was found to be dependent on the initial TC concentration and increasing TC concentration from 10 to 40mgl(-1) led to the decrease of the photolysis rate constant from 0.0045min(-1) to 0.0014min(-1). TC photolysis was highly pH-dependent and strongly enhanced at high pH value. Markedly elevated TC photolysis was also observed in the presence of nitrate and dissolved organic matter. Upon irradiation for 300min, only 15% reduction of total organic carbon (TOC) occurred in spite of quick conversion of 73% of TC, suggesting that a majority of TC transformed into intermediate products without complete mineralization. The intermediate products from TC photolysis were analyzed using high-performance liquid chromatography-electrospray ionisation-mass spectrometry (HPLC-ESI-MS) and the main photolysis products of TC were proposed. The toxicity of the photolysis compounds was evaluated using luminescent bacterium, and the results revealed that the toxicity increased with irradiation, indicative of a higher adversity risk of the degradation products of TC on bacteria upon photolysis.     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Solar photocatalytic mineralization of commercial pesticides: acrinathrin

A comparative study of the degradation of commercial acrinathrin spiked in water using TiO2 photocatalysis and photolysis under sunlight was performed. Samples were analysed by liquid chromatography-diode array detector (HPLC-DAD) and gas chromatography-ion trap-mass spectrometric detector (GC-ITMS). Additional total organic carbon (TOC) analyses were carried out to evaluate the mineralisation rates. One photoproduct, 2-phenoxy benzaldehyde, was unequivocally identified and evaluated by GC-ITMS during the processes. Although acrinathrin is almost destroyed when exposed to irradiation for more than 400 h, photocatalysis with TiO2 noticeably reduced degradation to a few hours. In this case, with the additional presence of peroxydisulphate, in less than 2 h acrinathrin is completely destroyed. Mineralisation of acrinathrin, without catalyst, was only around 50% after 400 h of irradiation.     

Photocatalytic degradation of an organophosphorus pesticide phosalone in aqueous suspensions of titanium dioxide

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO2 particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. The half-life (DT50) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K=0.0532 min(-1)). The half-life time of photomineralization in the concentration range of 7.5-20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

TiO_2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有：X射线衍射光谱（XRD）、激光散射粒径分布、傅立叶变换红外光谱（FT-IR）、X射线光电子谱（XPS）和透射电子显微镜（TEM）。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂（H2O2）用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明：制备的TiO2胶体粒子平均粒径为13.8 nm（激光散法测定）,光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/（L.min）,平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2（含量30%）用量为0.2%（V/V）,光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。