Chemical fractionation and heavy metal accumulation in the plant of Sesamum indicum (L.) var. T55 grown on soil amended with tannery sludge: Selection of single extractants

A pot experiment was carried out to study the single and sequential extractions of metals in different tannery sludge amendment and the potential of the plant of Sesamum indicum L. var. T55 (sesame) for the removal of metals from tannery waste contaminated site. The metal extraction efficiency obtained with each extractants was slightly different and follow the order; EDTA>DTPA>NH(4)NO(3)>NaNO(3)>CaCl(2). The correlation analysis between extractable metals in the different amendments of sludge and metal accumulation in the plant (lower and upper parts) showed better correlation for most of the tested metals with EDTA extraction. In this study, a sequential extraction technique was applied on different amendments of tannery sludge. The results showed that Mn, Zn, Cr and Cd were mostly associated with Fe-Mn oxide fraction in most of the amendments, K and Ni was found in residual (RES) fraction, Fe and Cu was bound with organic matter (OM) and RES fractions and Na was associated with carbonate (CAR) fraction. The metal accumulation after 60 d of growth of the plant was found in the order of K>Na>Fe>Zn>Cr>Mn>Cu>Pb>Ni>Cd and its translocation was found less in upper part. The accumulation of toxic metals (Cr, Ni and Cd) in the plants was found to increase with increase in sludge ratio, in contrast, the accumulation of Pb decreased. In view of growth parameters and metal accumulation in the plant, it was observed that lower amendments (25%) of tannery sludge were found suitable for the phytoremediation of most of the studied metals.     

中国部分城市污泥中矿质元素形态与生物可利用性研究

近年来随着城市污水处理厂数目迅速增加,低成本、高效率的污泥农用受到越来越多的关注。研究从北到南的五家污水处理厂消化污泥中矿质元素的含量和形态分布,为污泥资源化的合理利用提供科学参考。结果表明：消化污泥总体呈高有机质、高氮磷、低K、高矿质元素营养的相似性,但其理化性质如阳离子交换容量(CEC)、pH等差异较大,对矿质元素的形态分布与生物可利用性有明显的影响。同种元素在不同污泥中含量的差异较大,相差数倍,甚至十倍以上。污泥中不同元素含量明显不同,Fe的浓度最高,次之是Mg、Zn、B的浓度最低。连续提取研究表明,污泥pH对污泥中矿质元素的形态分布有明显影响,酸性污泥(厦门污水处理厂)中各矿质元素酸溶／交换态百分率明显高于其他污泥。Cu主要分布在氧化态;Zn的三态分布百分率均在10％以上;Mg、Mn的酸溶／交换态含量较高;Fe主要分布在残渣态;B氧化态和还原态的百分率较高。建议在全国范围内进行一次污水处理厂污泥品质调查,为污泥合理农用提供科学依据。     

Simple and sequential extractions of heavy metals from different sewage sludges

The presence of heavy metals in the sludges produced in waste-water treatment plants restricts their use for agricultural purposes. This study looks at different types of sludges (aerobic, anaerobic, unstabilised and sludge from a waste stabilisation pond) and compares the distribution of the heavy metals they contain according to the treatment that they have undergone. Some agronomic parameters necessary for characterising a sludge as suitable for use as amendment were determined. The aim of this study is to compare the availability and the localisation of heavy metals in different sewage sludges using simple (water and DTPA) extraction and the BCR (Community Bureau of Reference) sequential extraction procedure. It was confirmed that the total concentration of heavy metals did not exceed the limits set out by European legislation and that the stabilisation treatment undergone by the sludges strongly influenced the heavy metal distribution and the phases to which they were associated and their bioavailability level. The DTPA extraction procedure is cheap and easy to perform and the obtained results are similar to those obtained with the sequential procedure.     

Sequential extraction of heavy metals during composting of sewage sludge

The major limitation of soil application of sewage sludge compost is the total heavy metal contents and their bioavailability to the soil-plant system. This study was conducted to determine the heavy metal speciation and the influence of changing the physico-chemical properties of the medium in the course of composting on the concentrations, bioavailability or chemical forms of Cu, Zn, Pb and Ni in sewage sludge. Principal physical and chemical properties and FTIR spectroscopical characterization of sludge compost during treatment show the stability and maturity of end product. The total metal contents in the final compost were much lower than the limit values of composts to be used as good soil fertilizer. Furthermore, it was observed by using a sequential extraction procedure in sludge compost at different steps of treatment, that a large proportion of the heavy metals were associated to the residual fraction (70-80%) and more resistant fractions to extraction X-NaOH, X-EDTA, X-HNO3 (12-29%). Less than 2% of metals bound to bioavailable fractions X-(KNO3+H2O). Heavy metal distribution and bioavailability show some changes during composting depending on the metal itself and the physico-chemical properties of the medium. Bioavailable fractions of all elements tend to decrease except Ni-H2O. Zn and mainly Cu present more affinity to organic and carbonate fractions. In contrast, Pb is usually preferentially bound to sulfide forms X-HNO3. Nickel shows a significant decrease of organic form. Significant degrees of correlation were found between heavy metal fractions and changes of some selected variables (e.g. pH, ash, organic matter, humic substance) during the course of composting. Mobile fractions of metals are poorly predictable from the total content. The R2 value was significantly increased by the inclusion of other variables such as the amount of organic matter (OM) and pH.     

Electrokinetic enhancement removal of heavy metals from industrial wastewater sludge

An enhanced electrokinetic process for removal of metals (Cr, Cu, Fe, Ni, Pb, Zn) from an industrial wastewater sludge was performed. The electrokinetic experiments were conducted under a constant potential gradient (1.25 V cm(-1)) with processing fluids of tap water (TW), sodium dodecylsulfate (SDS) and citric acid (CA) for 5 days. Results showed that metal removal efficiency of heavy metals for EK-TW, EK-SDS and EK-CA systems are 11.2-60.0%, 37.2-76.5%, and 43.4-78.0%, respectively. A highest metal removal performance was found in EK-CA system. The removal priority of investigated metals from sludge by EK process was found as: Cu > Pb > Ni > Fe > Zn > Cr. The results of sequential extraction analysis revealed that the binding forms of heavy metals with sludge after electrokinetic process were highly depend upon the processing fluid operated. It was found that the binding forms of metals with sludge were changed from the more difficult extraction type (residual and sulfate fractions) to easier extraction types (exchangeable, sorbed, and organic fraction) after treatment by electrokinetic process. Results imply that if a proper treatment technology is followed by this EK process to remove metals more effectively, this treated sludge will be more beneficial for sludge utilization afterwards. Before it was reused, the risk associated with metals of more mobile forms to the environment need to be further investigated. The cost analysis was also evaluated for the investigated electrokinetic systems.     

Impact of sewage sludge spreading on heavy metal speciation in tropical soils (Réunion, Indian Ocean)

This study was designed to evaluate the impact of sewage sludge spreading on tropical soilborne heavy metal speciation. Sludgeborne heavy metal speciation was also assessed, and the potential mobility of the elements was classified as follows: Zn>Ni>Cu approximately Cr. Two sequential extraction procedures were applied to study Cr, Cu, Ni and Zn speciation in control soils and sludge-amended soils. We demonstrated that sewage sludge spreading over a 2-year period did not have an impact on soilborne heavy metal concentrations but affected speciation of the most mobile fractions of Ni and Zn. Both protocols were consistent for the organic matter fractions, with an increase in Cu, Zn and Cr concentrations in the amended soil as compared to the control soil. In addition, we highlighted that the two protocols characterized different pools of organic matter and that organic compounds remained in the solid matrix after extraction. With respect to the reducible fraction, completely opposite results were obtained with the two protocols and the solid residue study revealed that the two schemes were ineffective in characterizing iron and manganese fractions.     

焦化废水处理过程外排污泥中重金属形态特征及其潜在环境风险

焦化废水处理过程所排放污泥中重金属的含量及化学形态是否构成环境风险将直接影响污泥处置方法的选择,为此,实验采用BCR顺序提取法分析了焦化废水处理站外排污泥中重金属(Cd、Hg、Pb、Cr、As、Ni、Zn、Cu和Mn)的形态特征,并采用地累积指数(Igeo)和潜在生态危害指数(RI)评价了重金属对土壤的潜在环境风险。研究结果表明:除Ni主要以可氧化态存在外,焦化废水外排污泥中其他几种重金属元素主要存在于残渣态,重金属元素的含量低于《城镇污水处理厂污染物排放标准(GB18918—2002)》中的控制限值;与城市污泥相比,焦化废水外排污泥具有低Pb、Cr、Zn、Cu含量,而高Cd、Hg、Mn含量的特点;基于Igeo和RI的评价结果,Cd和Hg是外排污泥中具有一定环境风险的元素,需要考虑其下游去向。焦化废水处理外排污泥中主要存在残渣态重金属成分,不表现为很高的环境风险,其处置应重点考虑其中有机污染物特别是POPs。     

An ultrasonic assisted extraction method to release heavy metals from untreated sewage sludge samples

A rapid ultrasound accelerated sequential extraction procedure has been used to develop sequential extraction proposed by BCR protocol (the community Bureau of Reference now the European Union "Measurement and Testing Programme"). The effects of the ultrasonic treatment on the extraction of Cu, Cd, Cr, Pb, Ni and Zn from untreated sewage sludge collected from industrial site of Hyderabad city (Pakistan) were compared with those obtained from conventional sequentional extraction procedure of modified BCR protocol. In BCR method, each extraction steps takes 10h, where as with the use of compromise sonication conditions in ultrasonic bath, steps 1-3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 30, 30 and 30 min, respectively. Extractable Cd, Cr, Pb and Ni contents were obtained by both comparable methodologies were measured by electrothermal atomic absorption spectrometry (ETAAS), while for Cu and Zn Flame atomic absorption spectrometry (FAAS) was used. The validations of both methods were compared by the analysis of certified reference material of soil amended with sewage sludge (BCR 483). According to statistical evaluation of the results, the proposed accelerated extraction method is valid alternative to conventional shaking with much shorter extraction time with p value <0.05. The overall metal recoveries in steps 1-3 (excluding residual step) were 95-100% of those obtained with the conventional BCR protocol, except for Cu extracted (91.6%) as related to indicative values of Cu in BCR 483 obtained in 1-3 steps. The results of the partitioning study of untreated industrial waste water sewage sludge, indicate that more easily mobilized forms (acid exchangeable) were predominant for Cd and Zn, in contrast, the largest amount of Pb and Cr was associated with the iron/manganese oxide and organic matter/sulphide fractions.     

Use of the modified BCR three-step sequential extraction procedure for the study of trace element dynamics in contaminated soils

The modified BCR three-step sequential extraction procedure was used to examine the temporal dynamics of trace elements in soils contaminated by an accidental spill from an opencast mine in south-west Spain. Soils were mainly contaminated with pyritic sludge and acidic wastewater, whereas some soils were affected only by acidic wastewater. The distributions obtained for both some major (Ca, Fe and Mn) and trace elements (As, Cd, Cu, Pb and Zn) in the sludge and soil samples taken at different times after the accident, 1-3 months and 21 months, were compared. Sequential extractions were useful in identifying different sources of contamination, and in obtaining additional information on the solubility of secondary minerals formed by pyrite oxidation. Thus, the effectiveness of the BCR procedure has proved to be a useful tool for predicting short- and long-term mobility of trace elements, even in complex environmental scenarios.     

Metal availability and uptake by sorghum plants grown in soils amended with sludge from different treatments

Several factors depending on the sludge, the soil, or the combination of both substrates, may affect element availability to plants. In this study, an assessment was done of the effect of two sludges obtained by different processes (activated sludge and facultative stabilization pond) on heavy-metal availability and uptake by sorghum plants in soils with high and low copper contents. Results obtained for DTPA-extractable metal indicated higher metal availability in sludge-amended soils. In addition, sludges caused changes in copper and zinc distribution in soil, indicating in most cases a discrete increase in the more labile metal forms. However, observed changes did not increase heavy metal concentration in plant leaves, indicating that assessment of metal availability by a chemical procedure (single extraction or metal fractionation) would not permit a good prediction of metal bioavailability. On the other hand, sludge application at a rate of 100 t ha⁻¹ to high-copper agricultural soils would not imply greater mobility of this metal on account of a greater sorbing capacity provided by the sludges. Such results would indicate that sludges from wastewater treatment plants, meeting the standards of heavy metal contents, regardless of the process by which they were obtained, may be applied to several kinds of soil, even to high-copper soils, with no risk of increasing heavy metal bioavailability to phytotoxic levels in the short range.     

Metal fractionation in soils and assessment of environmental contamination in Vallecamonica, Italy

Metal contamination was investigated in soils of the Vallecamonica, an area in the northern part of the Brescia province (Italy), where ferroalloy industries were active for a century until 2001. The extent in which emissions from ferroalloy plants affected metal concentration in soils is not known in this area. In this study, the geogenic and/or anthropogenic origin of metals in soils were estimated. A modified Community Bureau of Reference sequential chemical extraction method followed by inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses were employed to evaluate the potential bioavailability of Al, Cd, Mn, Fe, Cr, Zn, and Pb in soils. Principal component analysis (PCA) was used to assess the relationships among metal sources in soil samples from different locations. This approach allowed distinguishing of different loadings and mobility of metals in soils collected in different areas. Results showed high concentrations and readily extractability of Mn in the Vallecamonica soils, which may suggest potential bioavailability for organisms and may create an environmental risk and potential health risk of human exposure.     

From agricultural use of sewage sludge to nutrient extraction: A soil science outlook

The composition of municipal wastewater and sewage sludge reflects the use and proliferation of elements and contaminants within society. In Sweden, official statistics show that concentrations of toxic metals in municipal sewage sludge have steadily decreased, by up to 90 %, since the 1970s, due to environmental programmes and statutory limits on metals in sludge and soil. Results from long-term field experiments show that reduced metal pollution during repeated sewage sludge application has reversed negative trends in soil biology. Despite this Swedish success story, organic waste recycling from Swedish towns and cities to arable land is still limited to only about 20 % of the total amount produced. Resistance among industries and consumers to products grown on land treated with sewage sludge may not always be scientifically grounded; however, there are rational obstacles to application of sewage sludge to land based on its inherent properties rather than its content of pollutants. We argue that application of urban organic wastes to soil is an efficient form of recycling for small municipalities, but that organic waste treatment from large cities requires other solutions. The large volumes of sewage sludge collected in towns and cities are not equitably distributed back to arable land because of the following: (i) The high water and low nutrient content in sewage sludge make long-distance transportation too expensive; and (ii) the low plant availability of nutrients in sewage sludge results in small yield increases even after many years of repeated sludge addition. Therefore, nutrient extraction from urban wastes instead of direct organic waste recycling is a possible way forward. The trend for increased combustion of urban wastes will make ash a key waste type in future. Combustion not only concentrates the nutrients in the ash but also leads to metal enrichment; hence, direct application of the ash to land is most often not possible. However, inorganic fertiliser (e.g. mono-ammonium phosphate fertiliser, MAP) can be produced from metal-contaminated sewage sludge ash in a process whereby the metals are removed. We argue that the view on organic waste recycling needs to be diversified in order to improve the urban–rural nutrient cycle, since only recycling urban organic wastes directly is not a viable option to close the urban–rural nutrient cycle. Recovery and recycling of nutrients from organic wastes are a possible solution. When organic waste recycling is complemented by nutrient extraction, some nutrient loops within society can be closed, enabling more sustainable agricultural production in future.     

Evaluation of various chemical extraction methods to estimate plant-available arsenic in mine soils

Elevated levels of bioavailable As in mining soils, agricultural areas and human habitats may cause potential toxicity to human health, plants and microbe. Therefore, it is essential to determine proper soil chemical extraction method in order to estimate plant-available As in mining soils and protect agricultural and environmental ecosystems by evaluation of environmental risk and implementation of remediation measures. In this study, six single soil chemical extraction processes and four-step sequential chemical extraction protocol were used to determine the relative distribution of As in different chemical forms of soils and their correlations with total As in plants grown in mining areas and greenhouse experiments. The strongest relationship between As determined by single soil chemical extraction and As in plant biomass was found for sodium acetate and mixed acid extractant. The mean percent of total As extracted was: ammonium oxalate (41%)>hydroxylamine hydrochloride (32%)>mixed acid (16%)>phosphate (6%)>sodium acetate (1.2%)>water (0.13%). This trend suggests that most of the As in these soils is inside the soil mineral matrix and can only be released when iron oxides and other minerals are dissolved by the stronger chemical extractant. Single soil chemical extraction methods using sodium acetate and mixed acids, that extract As fractions complexed to soil particles or on the surface of mineral matrix of hydrous oxides of Fe, Mn and Al (exchangeable+sorbed forms) can be employed to estimate and predict the bioavailable As fraction for plant uptake in mining affected soils. In sequential chemical extraction methods, ammonium nitrate and hydroxylamine hydrochloride may be used to provide closer estimates of plant-available As in mining soils.     

Decontamination of polycyclic aromatic hydrocarbons and nonylphenol from sewage sludge using hydroxypropyl-β-cyclodextrin and evaluation of the toxicity of leachates

A decontamination technique based in cyclodextrin extraction has been developed to eliminate nonylphenol (NP) and 16 polycyclic aromatic hydrocarbons (PAHs; the US Environmental Protection Agency priority pollutants list) from sewage sludge. In a first step, PAHs and NP were characterised in six sludges to determine contamination levels according to limit values proposed by the European Union Sludge Directive draft. There were few variations in the total PAHs content with levels of 1.88 to 3.05 mg kg^?1. Three-ring PAHs predominated, but fluoranthene and pyrene were also present. None of the sludge exceeded the PAHs limit proposed by the European Union’s draft Directive. On the contrary, NP content in four of the six sludges was over the recommended limits of 50 mg kg^-1 for NP ethoxylates. With the aim of obtaining NP values below the concentration limits proposed to use the sewage sludge as agricultural amendments, a preliminary study using hydroxypropyl-β-cyclodextrin (HPBCD) extractions as a decontamination technique was carried out. About 90 % of NP content was removed with only one extraction with HPBCD, whereas after three sequential extractions using an aqueous solution without HPBCD, the NP extraction percentage was less than 1 %. Simultaneously, PAHs extraction percentages obtained with HPBCD were also much higher than when aqueous solution was used, especially in the case of two- and three-ring PAHs. Finally, the potential environmental hazard of HPBCD leachates to aquatic organisms (Daphnia magna) was tested. These results indicate that the treatment of sewage sludge with cyclodextrin could allow their safe use as fertiliser in agriculture.     

Study of the effects of drinking water treatment sludge on the properties of Class F fly ash-based geopolymer

Environmental Science and Pollution Research - Drinking water treatment sludge (DWTS) generated from water treatment plants is a global issue because of the environmental risks it imposes. Managing...     

Solid phase speciation of arsenic by sequential extraction in standard reference materials and industrially contaminated soil samples

Availability, mobility, (phyto)toxicity and potential risk of contaminants is strongly affected by the manner of appearance of elements, the so-called speciation. Operational fractionation methods like sequential extractions have been applied for a long time to determine the solid phase speciation of heavy metals since direct determination of specific chemical compounds can not always be easily achieved. The three-step sequential extraction scheme recommended by the BCR and two extraction schemes based on the phosphorus-like protocol proposed by Manful (1992, Occurrence and Ecochemical Behaviours of Arsenic in a Goldsmelter Impacted Area in Ghana, PhD dissertation, at the RUG) were applied to four standard reference materials (SRM) and to a batch of samples from industrially contaminated sites, heavily contaminated with arsenic and heavy metals. The SRM 2710 (Montana soil) was found to be the most useful reference material for metal (Mn, Cu, Zn, As, Cd and Pb) fractionation using the BCR sequential extraction procedure. Two sequential extraction schemes were developed and compared for arsenic with the aim to establish a better fractionation and recovery rate than the BCR-scheme for this element in the SRM samples. The major part of arsenic was released from the heavily contaminated samples after NaOH-extraction. Inferior extraction variability and recovery in the heavily contaminated samples compared to SRMs could be mainly contributed to subsample heterogeneity.     

Phosphorus recovery from wastewater--expert survey on present use and future potential

Today, a variety of different approaches to the recovery of phosphorus from wastewater, sludge, and sludge ash exist. These approaches differ basically by the origin of the used matter (wastewater, sludge liquor, fermented or nonfermented sludge ash) and the process (precipitation, wet-chemical extraction, and thermal treatment). To rate them according to their characteristics, the latter were phrased as hypotheses and subjected to an international expert survey. The survey showed that phosphorus recovery is expected to become an established process over the next 20 years in industrialized countries for economic reasons. A decisive aspect in this regard will be the quality of the produced fertilizer. Simple technologies such as the recovery from sludge liquor seem to be preferred. If sludge is incinerated, phosphorus recycling from ash then becomes more interesting and has to be considered. Phosphorus recovery and source-separating sanitation technologies are more appropriate for industrialized countries than for developing countries. Because the growing awareness of environmental issues will prevent sludge from being used agriculturally in an increasing number of countries in the next decade, the market potential for nutrient recovery technologies will increase in the immediate future.     

Transportation and distribution of chromium in the anaerobic sludge treating the chromium-containing wastewater

The chromium distribution and transportation in the anaerobic activated sludge was investigated using a sequential extraction method. The results showed that Cr(VI) in aqueous solution was reduced by the metabolic product of SRB and form indissoluble Cr(OH)₃ in a solid phase. More than 99% of Cr(III) in the sludge was in a stable residual form (RES) of bio-reduction. The Cr(VI) was mainly present in RES and organic form (OR). With increasing Cr(VI) concentration, Cr(VI) was transferred from RES into OR and even exchangeable form (EXCH). Meanwhile, sulphate and co-existing metal ions affected the occurrence form of Cr(VI).     

Ecotoxicity, phytotoxicity and extractability of heavy metals from different stabilised sewage sludges

The presence of heavy metals in the sludges produced in wastewater treatment plants restricts their use for agricultural purposes. This study compares different types of sludges (aerobic, anaerobic, unstabilised and sludge from a waste stabilisation pond) in order to assess the extractability of heavy metals using simple extraction, water and DTPA. The stabilisation treatment undergone by the sludges influenced the heavy metals extractability. The least mineralised sludges (unstabilised and aerobic) showed higher metal extractability. The sewage sludges were subjected to chemical characterisation and toxicity testing (ecotoxicity and phytotoxicity assays) in absence of substrate, to provide a preliminary assessment of their suitability for land application. The ecotoxicity assays confirmed that no sludge constituted a hazardous waste. The sludge extracts had significant adverse effect on the germination index (GI) of barley (Hordeum vulgare L.) and cress (Lepidium sativum L.), a fact which indicates that some characteristics affected root growth.     

The environmental fate of the primary degradation products of alkylphenol ethoxylate surfactants in recycled paper sludge.

Alkylphenol ethoxylates (APEOs) are a group of non-ionic surfactants that are degraded microbially into more lipophilic degradation products with estrogenic potential, including nonylphenol monoethoxylate (NP1EO), nonylphenol diethoxylate (NP2EO), octylphenol (4-tOP) and nonylphenol (4-NP). Nonylphenol ethoxylates are used in paper recycling plants for de-inking paper and have the potential to be released into the environment through spreading of wastewater treatment sludge for soil amendment. Three samples of recycled paper sludge were collected from farmers' fields and analyzed for concentrations of NP1EO, NP2EO, 4-NP and 4-tOP. Each sample differed in the amount of time elapsed since the sludge was placed on farmers' fields. Primary degradation products of APEOs were present at low micrograms/g concentrations in the sludge samples. Differences in the concentrations of these analytes in sludge samples indicated that APEO concentrations declined by 84% over a period of 14 weeks on farmers' fields. Changes in the chromatographic patterns of acetylated 4-NP indicated that there is a group of recalcitrant nonylphenol isomers that degrades more slowly than other isomers. These data indicate that microbial degradation may reduce the risk of environmental contamination by these compounds, but more work is required to assess the toxic potential of APEOs in sludges used for soil amendment.