微生物燃料电池电活化过硫酸盐降解甲基橙偶氮染料

为研究MFC（微生物燃料电池）产生电能活化PDS（过硫酸盐）对偶氮染料的降解能力,以MO（甲基橙）为目标污染物,探讨pH、c（PDS）、初始c（MO）、无机阴离子等对MO降解的影响及降解机理.结果表明:①当pH为3~5时,MO降解率随pH降低而升高;当pH低于3时,MO降解率随pH的降低而降低;MO降解率随初始c（MO）的增大而降低.当c（PDS）为1~2 mmol/L时,MO降解率随c（PDS）增加而增大;当c（PDS）超过2 mmol/L后呈减小趋势.②最佳反应条件[pH为3、初始c（MO）为0.10 mmol/L、c（PDS）为2 mmol/L]下,反应4 h后MO降解率可达86.5%.③无机阴离子HCO₃-、NO₃-、CO₃2-对MO降解存在抑制作用,当阴离子投加量为10 mmol/L时,降解率分别为64.2%、68.8%、76.1%,而Cl-对MO降解无显著影响.④淬灭试验表明,体系的主要活性物质为SO₄-·及少量·OH.⑤通过紫外-可见光谱扫描,依据MO结构与特征吸收峰的关系,推测MO降解途径,即MO发色基团偶氮双键断裂,生成含苯环类中间产物,最终矿化为CO₂和H₂O.研究显示,MFC能有效活化PDS产生SO₄-·,对偶氮染料有较好的降解和矿化效果.      

Fe2+与Fe0活化过二硫酸盐降解活性艳蓝KN-R

为了解Fe2+与Fe0在活化PDS(过二硫酸盐)降解活性艳蓝KN-R时的差异,通过序批试验,考察了Fe2+/PDS和Fe0/PDS体系中c(Fe2+)、ρ(Fe0)、c(PDS)和初始pH对KN-R降解的影响. 结果表明:在Fe2+/PDS体系中,最佳反应条件〔初始pH为3.0,c(Fe2+)为1.0 mmol/L,c(PDS)为2.0 mmol/L〕下,180 min后KN-R的去除率达到96.55%;过高的pH和c(Fe2+)对KN-R的降解均有明显的抑制作用. 在Fe0/PDS体系中,当pH和ρ(Fe0)过高时,KN-R的去除率仍维持在较高水平,当pH为9.0时,180 min后KN-R的去除率为90.53%;当ρ(Fe0)为448 mg/L时,50 min后KN-R的去除率就能达到94.35%. 在2个体系中,c(PDS)的升高均能显著提高KN-R的去除率,当c(PDS)由0.5 mmol/L增至8.0 mmol/L时,KN-R的去除率由47.25%(Fe2+/PDS体系)和57.00%(Fe0/PDS体系)增至100%. 动力学分析显示,KN-R的降解均遵循一级反应动力学;最佳反应条件下2个体系中的活性自由基均以硫酸根自由基(SO₄-·)为主. 因此,在降解KN-R过程中,Fe0/PDS体系的性能明显优于Fe2+/PDS体系.      

Enhanced activation of peroxydisulfate by strontium modified BiFeO3perovskite for ciprofloxacin degradation

A series of Sr-doped BiFeO₃ perovskites (Bi_1-xSr_xFeO₃, BSFO) fabricated via sol-gel method was applied as peroxydisulfate (PDS) activator for ciprofloxacin (CIP) degradation. Various technologies were used to characterize the morphology and physicochemical features of prepared BSFO samples and the results indicated that Sr was successfully inserted into the perovskites lattice. The catalytic performance of BiFeO₃ was significantly boosted by strontium doping. Specifically, Bi_0.9Sr_0.1FeO₃ (0.1BSFO) exhibited the highest catalytic performance for PDS activation to remove CIP, where 95% of CIP (10 mg/L) could be degraded with the addition of 1 g/L 0.1BSFO and 1 mmol/L PDS within 60 min. Moreover, 0.1BSFO displayed high reusability and stability with lower metal leaching. Weak acidic condition was preferred to neutral and alkaline conditions in 0.1BSFO/PDS system. The boosted catalytic performance can be interpreted as the lower oxidation state of Fe and the existence of affluent oxygen vacancies generated by Sr doping, that induced the formation of singlet oxygen (¹O₂) which was confirmed as the dominant reactive species by radical scavenging studies and electron spin resonance (ESR) tests. The catalytic oxidation mechanism related to major ¹O₂ and minor free radicals was proposed. Current study opens a new avenue to develop effective A-site modified perovskite and expands their application for PDS activation in wastewater remediation.     

Ti/RuO_2-Pt电极电化学降解苯酚废水研究

研究以典型的难降解有机污染物苯酚为对象,用Ti/RuO2-Pt阳极进行电催化氧化降解研究,讨论了电解质、苯酚初始浓度、电流密度以及氨氮对苯酚降解效果的影响。研究结果表明:以NaCl为电解质比Na2SO4为电解质时处理苯酚的效果明显,而且电流密度越大、NaCl的添加量越多,苯酚全部降解所需的时间越短;在10mA/cm2的电流密度,0.3g/L氯化钠的添加量下,将苯酚从8mg/L降解为0需要30min。在电流浓度10mA/cm2,氯化钠添加量1.0g/L下,苯酚由20、40、80mg/L降解为0分别需要30、60、130min,降解时间随着浓度的增加呈接近正比增加;氨氮的存在不影响苯酚的电化学降解,而且苯酚优先降解,然后氨氮降解。     

热带假丝酵母8953菌株对苯酚的降解特性研究

实验室分离的一株热带假丝酵母(编号为8953)具有较强的苯酚降解能力,并可以利用苯酚、间苯二酚、联苯胺等芳烃为唯一碳源和能源生长。该菌株在48h内可完全降解约14.88mmol/L苯酚,完全降解10.63mmol/L苯酚只需要24h,其降解苯酚浓度最高可达19.13mmol/L。在pH4～9,温度20℃～40℃范围内,苯酚浓度为10.0mmol/L条件下该菌株均保持100%的降解率。该菌株降解苯酚的最适pH范围为6.0～8.0,最适温度范围为28℃～30℃,最佳接种量为1%～3%,外源添加氮源能促进酵母生长和苯酚的降解。     

纳米零价铁基生物炭活化过硫酸盐降解土霉素

采用纳米零价铁基生物炭(nZVI-BC)耦合过二硫酸钠(PDS)或过硫酸氢钾(PMS)构建吸附-高级氧化复合体系开展水中土霉素(OTC)的高效降解。考察了在不同PDS/PMS浓度、nZVI-BC投量、OTC浓度及初始pH条件下OTC的去除规律,并对体系中活性物种进行探究。结果表明:在0.20 mmol/L PDS/PMS,0.01 g nZVI-BC,50 mg/L OTC,原始pH为5.0±0.1条件下,OTC去除率可达到80%以上;SO₄-·在nZVI-BC/PDS体系中对OTC降解占有绝对主导地位(贡献度为57.00%),nZVI-BC/PMS体系则主要依靠SO₄-·、O₂-·和1O₂。     

Environmental factors affecting degradation of perfluorooctanoic acid (PFOA) by In2O3 nanoparticles

Nanophotocatalysts have shown great potential for degrading poly- and perfluorinated substances (PFAS). In light of the fact that most of these catalysts were studied in pure water, this study was designed to elucidate effects from common environmental factors on decomposing and defluorinating perfluorooctanoic acid (PFOA) by In₂O₃ nanoparticles. Results from this work demonstrated that among the seven parameters, pH, sulfate, chloride, H₂O₂, In₂O₃ dose, NOM and O₂, the first four had statistically significant negative effects on PFOA degradation. Since PFOA is a strong acid, the best condition leading to the highest PFOA removal was identified for two pH ranges. When pH was between 4 and 8, the optimal condition was: pH = 4.2; sulfate = 5.00 mg/L; chloride = 20.43 mg/L; H₂O₂ = 0 mmol/L. Under this condition, PFOA decomposition and defluorination were 55.22 and 23.56%, respectively. When pH was between 2 and 6, the optimal condition was: pH = 2; sulfate = 5.00 mg/L; chloride = 27.31 mg/L; H₂O₂ = 0 mmol/L. With this condition, the modeled PFOA decomposition was 97.59% with a defluorination of approximately 100%. These predicted results were all confirmed by experimental data. Thus, In₂O₃ nanoparticles can be used for degrading PFOA in aqueous solutions. This approach works best when the target contaminated water contains low concentrations of NOM, sulfate and chloride and at a low pH.     

Fe3O4/CeO2复合材料催化降解橙黄G的效能及降解途径

为研究磁性纳米Fe₃O₄/CeO₂复合材料在高浓度难降解有机废水处理中的应用,利用共沉淀法制备Fe₃O₄/CeO₂复合材料,并将其作为非均相类Fenton催化剂降解橙黄G染料废水,利用单因素法优化出最佳降解工艺,同时利用TOF-MS/MS(飞行时间质谱)检测降解中间产物,推测出可能降解途径.结果表明,当Ce/Fe为1 :1(质量比)时制备的Fe₃O₄/CeO₂复合材料催化效果最佳.最佳降解工艺条件:初始pH为2.0,温度为30 ℃,H₂O₂投加量为30 mmol/L,Fe₃O₄/CeO₂复合材料的投加量为2.0 g/L,初始ρ(橙黄G)为50 mg/L.在最佳降解工艺条件下反应120 min后,橙黄G去除率为96.2%,TOC去除率为65.0%,Fe₃O₄/CeO₂复合材料至少可重复利用6次.研究显示,橙黄G降解主要有三条可能的降解途径,包括偶氮键断裂、偶氮键与苯环断开、脱磺酸基、羟基化以及开环等过程,共检测出八种可能的降解中间产物,主要有苯胺、苯酚、萘酚以及羧酸等.      

高级氧化处理苯酚废水的研究

采用Fenton试剂和O3对COD为950mg/L的苯酚废水进行化学氧化处理,通过实验确定各自最佳的运行参数。Fenton:n(H2O2)=36mmol/L,n(H2O2):n(Fe2+)=3,pH为3,反应时间为2h,COD去除率为90%;O3:投加量为1200mg/L,pH为11时COD的去除率为60%,两种氧化技术都有较好的处理效果。     

FeOOH催化降解苯酚的性能研究

用沉淀法制备FeOOH,以此为催化剂采用非均相Fenton高级氧化技术降解苯酚。对催化剂的投加量、H2O2的投加量、初始pH对苯酚去除的影响进行了实验研究。结果表明,pH=3.0、双氧水的投加量为19.6mmol·L-1,催化剂的投加量为2.0 g·L-1,室温下反应10 min,苯酚的去除率可达90%以上。非均相Fenton氧化法降解苯酚能有效拓宽反应溶液pH值范围,对废水的苯酚的去除具有广阔的应用前景。     

超声波/零价铁协同降解苯酚的研究

研究了超声波/零价铁协同降解苯酚的过程,并对其降解机理进行了研究,分别考察了零价铁投加量,溶液初始浓度,初始pH值,超声功率等因素对苯酚降解的影响规律。结果表明,超声波/零价铁工艺能有效的降解水中的苯酚,零价铁的最佳投加量为0.8 g/L,苯酚浓度越低处理效果越好,苯酚在酸性条件的降解率高于碱性条件,在0~400 W超声作用下,功率越大,降解率越大;超声波与零价铁粉对苯酚的降解具有协同作用,其降解过程符合一级动力学规律。在体系中加入自由基捕获剂正丁醇抑制了苯酚的降解,说明苯酚的降解过程主要依靠羟基自由基(.OH)的氧化作用。     

Removal of phenol by activated alumina bed in pulsed high-voltage electric field

A new process for removing the pollutants in aqueous solution-activated alumina bed in pulsed high-voltage electric field was investigated for the removal of phenol under different conditions. The experimental results indicated the increase in removal rate with increasing applied voltage, increasing pH value of the solution, aeration, and adding Fe^2＋. The removal rate of phenol could reach 72.1% when air aeration flow rate was 1200 ml/min, and 88.2% when 0.05 mmol/L Fe^2＋ was added into the solution under the conditions of applied voltage 25 kV, initial phenol concentration of 5 mg/L, and initial pH value 5.5. The addition of sodium carbonate reduced the phenol removal rate. In the pulsed high-voltage electric field, local discharge occurred at the surface of activated alumina, which promoted phenol degradation in the thin water film. At the same time, the space-time distribution of gas-liquid phases was more uniform and the contact areas of the activated species generated from the discharge and the pollutant molecules were much wider due to the effect of the activated alumina bed. The synthetical effects of the pulsed high-voltage electric field and the activated alumina particles accelerated phenol degradation.     

氧基氯化铁非均相活化过一硫酸盐降解金橙Ⅱ

采用部分热分解法制备了氧基氯化铁（FeOCl）,用于活化过一硫酸盐（PMS）降解难降解偶氮染料金橙Ⅱ（AO7）.利用X射线光电子能谱分析（XPS）、扫描电镜（SEM）和X射线衍射光谱（XRD）对其进行了表征;通过实验评估FeOCl/PMS体系对AO7的降解效果并分析了影响AO7去除率的各种因素.结果表明：FeOCl活化PMS降解AO7效果良好,矿化率达44%.在中性条件下,当FeOCl投加量50mg/L、PMS浓度1.0mmol/L、AO7浓度0.05mmol/L时,AO7可在30min内完全降解.随PMS投加量、FeOCl投加量、Cl^-浓度和反应初始pH值的增大,AO7的脱色效果提高.FeOCl还具有良好的重复利用性.此外,通过自由基淬灭实验、EPR测试和XPS分析了反应的主要活性物种和反应机理：由PMS活化产生的SO₄^-·和·OH对污染物进行降解,其中主要活性物种为SO₄^-·.     

Degradation of bisphenol-A using ultrasonic irradiation assisted by low-concentration hydrogen peroxide

This study investigated the degradation of bisphenol-A (BPA) by ultrasonic irradiation in the presence of different additives (H2O2,air bubbles and humic acid) under various operating conditions,i.e.,ultrasonic frequency,power intensity and power density.The results demonstrated that the BPA degradation followed pseudo first-order kinetics under different experimental conditions.The optimum power intensities were 0.9,1.8,and 3.0W/cm 2 at the frequencies of 400,670,and 800 kHz,respectively.At the fixed frequ...     

耐低温苯酚降解菌的降解动力学研究

研究耐低温菌在15℃水温条件下对不同浓度苯酚的生物降解作用,采用反应动力学方程拟合其降解过程。结果表明：菌株在低温下可降解苯酚,当菌体质量浓度一定时,苯酚降解率及平均降解速率主要与苯酚初始浓度有关。当初始浓度〈350 mg/L时,在48 h内可完全降解,菌株降解过程中没有出现苯酚毒性抑制作用,遵循Monod方程;当初始浓度〉350 mg/L时,苯酚降解率及降解速率均有所下降,由于初始浓度高对菌体产生了抑制作用,降解过程以基质抑制型的Hal-dane方程为主。     

H2O2引发的UV/Fenton苯酚光催化降解

研究了H2O2引发光催化降解方法对废水中微量苯酚的去除效果,应用传感技术分析了降解过程中H2O2浓度变化,及其H2O2引发光催化降解苯酚的机理,考察了影响苯酚光催化降解的因素,确定了最佳降解试验条件为:H2O2 0.075~0.30mmol/L,Fe3+ 0.1~0.15mmol/L,pH值 4~5.在此条件下,苯酚初始浓度为50mg/L的含酚废水反应2h,苯酚降解率达到95%,矿化去除率达77%.     

Application of ferrate（VI） in the treatment of industrial wastes containing metal-complexed cyanides ： A green treatment

Ferrate(VI) was employed for the oxidation of cyanide (CN) and simultaneous removal of copper or nickel in the mixed/complexed systems of CN-Cu, CN-Ni, or CN-Cu-Ni. The degradation of CN (1.00 mmol/L) and removal of Cu (0.095 mmol/L) were investigated as a function of Fe(VI) doses from 0.3–2.00 mmol/L at pH 10.0. It was found that Fe(VI) could readily oxidize CN and the reduction of Fe(VI) into Fe(III) might serve e ciently for the removal of free copper ions. The increase in Fe(VI) dose apparently favoured the CN oxidation as well as Cu removal. Moreover, the pH dependence study (pH 10.0–13.0) revealed that the oxidation of CN was almost una ected in the studied pH range (10.0–13.0), however, the maximum removal e ciency of Cu was obtained at pH 13.0. Similarly, treatment was carried out for CN-Ni system having the initial Ni concentration of 0.170 mmol/L and CN concentration of 1.00 mmol with Fe(VI) dose 2.00 mmol at various pH values (10.0–12.0). Results showed a partial oxidation of CN and partial removal of Ni. It can be observed that Fe(VI) can partially degrade the CN-Ni complex in this pH range. Further, Fe(VI) was applied for the treatment of simulated industrial waste/e uent waters treatment containing CN, Cu, and Ni.     

EDDS强化Fe0-Al0体系降解废水中4-氯酚的性能和机理

采用乙二胺二琥珀酸（EDDS）强化Fe⁰-Al⁰体系还原水溶液中的O₂产生H₂O₂和·OH等活性氧（ROS）的绿色高级氧化工艺,以4-氯酚（4-CP）模拟废水为研究对象,考察了溶液的初始pH值、铁铝的质量比、EDDS投加量和4-CP的初始浓度等因素对4-CP降解的影响.采用电子自旋共振（ESR）法、苯甲酸捕捉法以及4-CP的降解产物等证实了ROS的产生及4-CP的降解机制.结果表明：EDDS强化Fe⁰-Al⁰/O₂体系对4-CP的去除率随溶液初始pH的升高而降低,但在pH=2.5～9范围内,始终具有较好的4-CP去除率;随Fe⁰：Al⁰质量比增加4-CP的去除率先增大后减小,最佳质量比为4：1;随EDDS投加量和4-CP初始浓度增加,4-CP的去除率增大;EDDS可使体系的高级氧化能力提高9倍,在初始pH=2.5、Fe⁰=8g/L、Al⁰=2g/L、EDDS=1.5mmol/L条件下,反应3h后100mg/L 4-CP的去除率和脱氯率均达到近100%..     

微量元素对黄孢原毛平革菌降解苯酚的影响

研究了氮源,铁、铜、锰等金属元素以及Tween 80等有机添加剂对黄孢原毛平革菌降解苯酚的影响。结果表明,氮源是黄孢原毛平革菌生长的必需元素,铜元素和锰元素对苯酚降解具有明显的促进作用,而铁元素的促进作用并不显著。各种微量元素的最佳浓度分别为:氮0.1 g/L、铁0.5 mmol/L、锰1.0 mmol/L、铜0.3 mmol/L、Tween 80 0.01 mmol/L。     

水相中苯酚光催化降解的全额光子效率

为定量评价光催化反应器的性能,利用主辐射波长为207 nm的KrBr*准分子灯降解水相中的苯酚,测定了光解和光催化降解2种体系中苯酚和TOC去除率,并计算了苯酚降解的ξ_g(全额光子效率),探讨了其影响因素. 结果表明:①延长反应时间、加入适量催化剂、降低初始c(苯酚)能提高苯酚和TOC去除率. 采用动力学模型对苯酚的降解进行拟合,表明光解和光催化降解体系中苯酚的降解均符合准一级动力学模型. ②加入催化剂和提高初始c(苯酚)均可以获得较高的ξ_g,而光源的辐射功率与ξ_g没有线性相关性;在辐射功率为0.76 W、初始c(苯酚)为1.10 mmol/L、催化剂投加量(以ρ计)为0.8 g/L的条件下,ξ_g为5.56%. ③采用高效液相色谱对光催化降解体系中生成的中间产物的变化规律进行研究发现,4种中间产物表现为c(对苯二酚)＞c(邻苯二酚)＞c(对苯醌)＞c(间苯二酚);通过建立苯酚及中间产物的拟一级降解动力学模型,证实苯酚光催化降解历程为苯酚→芳香烃中间产物→最终产物.