Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

Nb2O5 nanowires in-situ grown on carbon fiber: A high-efficiency material for the photocatalytic reduction of Cr(VI)

Niobium oxide nanowire-deposited carbon fiber (CF) samples were prepared using a hydrothermal method with amorphous Nb₂O₅·nH₂O as precursor. The physical properties of the samples were characterized by means of numerous techniques, including X-ray diffraction (XRD), energy-dispersive spectroscopy (EDS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected-area electron diffraction (SAED), UV–visible spectroscopy (UV–vis), N₂ adsorption–desorption, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy. The efficiency for the removal of Cr(VI) was determined. Parameters such as pH value and initial Cr(VI) concentration could influence the Cr(VI) removal efficiency or adsorption capacity of the Nb₂O₅/carbon fiber sample obtained after hydrothermal treatment at 160°C for 14 hr. The maximal Cr(VI) adsorption capacity of the Nb₂O₅ nanowire/CF sample was 115 mg/g. This Nb₂O₅/CF sample also showed excellent photocatalytic activity and stability for the reduction of Cr(VI) under UV-light irradiation: the Cr(VI) removal efficiency reached 99.9% after UV-light irradiation for 1 hr and there was no significant decrease in photocatalytic performance after the use of the sample for 10 repeated cycles. Such excellent Cr(VI) adsorption capacity and photocatalytic performance was related to its high surface area, abundant surface hydroxyl groups, and good UV-light absorption ability.     

Optimized photocatalytic regeneration of adsorption-photocatalysis bifunctional composite saturated with Methyl Orange

Photo-responsive adsorption-photocatalysis nanocomposites are generally used in water and wastewater decontamination; however, the prolonged adsorption capacity of composites and the role of adsorption in concomitant photocatalysis are typically neglected. These composites can be regenerated under light irradiation as their adsorption capacity decreases. Herein, a novel adsorption-photocatalysis bifunctional nanocomposite, Bi-doped TiO₂ supported on powdered activated carbon (Bi₂O₃/TiO₂/PAC), was prepared using the sol-impregnation-hydrothermal procedure. Bi₂O₃/TiO₂/PAC with a secondary calcination temperature of 700°C under a nitrogen atmosphere was selected for maximum adsorption capacity on Methyl Orange (MO). The composite displayed an excellent adsorption capacity and was easily separated and recycled. The results demonstrate that 71.2% photocatalytic regeneration efficiency could be attained under visible light irradiation for 1 hr at an intensity of 750?W/m² and pH 7. Characterization of the as-prepared Bi₂O₃/TiO₂/PAC nanocomposite (700°C) indicates that it possesses a highly specific surface area and great optical properties, showing bifunctional adsorption-photocatalysis characteristics. The p-n heterojunction of the composite played a dominant role in the photocatalytic regeneration process, and effective degradation of MO could be achieved along with composite regeneration.     

In situ construction of Z-scheme FeS2/Fe2O3 photocatalyst via structural transformation of pyrite for photocatalytic degradation of carbamazepine and the synergistic reduction of Cr(VI)

Pyrite is the most abundant sulfide semiconductor mineral with excellent optical properties. However, few reports have investigated its photocatalytic activity because of the low photogenerated carrier separation efficiency. In this work, a Z-scheme FeS₂/Fe₂O₃ composite photocatalyst was fabricated in situ via structural transformation of pyrite through heat treatment. A remarkably enhanced photocatalytic performance was observed over the FeS₂/Fe₂O₃ composite photocatalyst. Compared with the pristine pyrite, the degradation efficiency of carbamazepine (CBZ) reached 65% at the added hexavalent chromium (Cr(Ⅵ)) concentration of 20 mg/L and the Cr(Ⅵ) was nearly completely reduced in the mixed system using FeS₂/Fe₂O₃ within 30 min under simulated solar light irradiation. The enhanced photocatalytic activity can be attributed to the efficient separation and transfer of photogenerated carriers in the FeS₂/Fe₂O₃ composite photocatalyst. This facilitated the generation of ?OH, hole (h⁺) and ?O₂^? species, which participated in the photocatalytic reaction with CBZ. Based on the measurement of the active species and electric properties, a Z-scheme electron transfer pathway was proposed for the FeS₂/Fe₂O₃ composite photocatalyst. This work broadens the application potential of pyrite in environmental remediation.     

0D/3D direct Z-scheme heterojunctions hybridizing by MoS2 quantum dots and honeycomb conjugated triazine polymers (CTPs) for enhanced photocatalytic performance

Herein, a novel direct Z-scheme photocatalyst was accomplished by hybridization of 0D MoS₂ quantum dots (MSQDs) and 3D honeycomb-like conjugated triazine polymers (CTP) (namely, CTP-MSQD). The unique 0D/3D hierarchical structure significantly enhanced the exposure of active sites and light harvesting property, while the formed p-n junction enabled the direct strong interface coupling without the necessity of any mediators. The optimized CTP-MSQD3 exhibited continuously increased visible-light-driven photocatalytic activity and strong durability both in Cr(VI) reduction and H₂ evolution, featured a rate of 0.069 min⁻¹ and 1070 µmol/(hr∙g), respectively, which were 8 times than those of pure 3D-CTP (0.009 min⁻¹ and 129 µmol/(hr∙g)). We believe that this work provides a promising photocatalyst system that combines a 0D/3D hierarchical structure and a Z-scheme charge flow for efficient and stable photocatalytic conversion.     

Photocatalytic degradation of dichlorvos using TiO2 supported on hollow glass microbeads

In this paper, a method for TiO₂ supported on hollow glass microbeads was described and the feasibility of photocatalytic degradation of dichlorvos using supported TiO₂(TiO₂/beads) was studied. The results showed that 1.0×10^-4 mol.dm^-3 of dichlovos could be completely photocatalytically degraded into PO₄^3- after 120 min illumination with a 375 W medium pressure mercury lamp. The effects of the amount of TiO₂/beads and concentration of Cu²⁺ on the photocatalytic degradation were also investigated. Some intemediate products of photocatalytic degradation of dichlorvos were detected.     

Effect of crystalline structure on terbuthylazine degradation by H2O2-assisted TiO2 photocatalysis under visible irradiation

Various methods for shifting the optical response of TiO₂ into the visible (Vis) range have been reported. Herein, we reported the application of a TiO₂/H₂O₂/Vis process and the effects of TiO2 crystalline structure on the degradation of terbuthylazine. The results indicated that TiO₂ crystalline structure and H₂O₂ addition had significant effects on terbuthylazine degradation: its degradation rate could be increased from 7% to 70% with H₂O₂ addition after 180?min of reaction, the synergistic degradation of terbuthylazine by TiO₂-Fe^{3 +} was substantially accelerated, with the degradation rate reaching up to 100% after 20?min of reaction, and rutile TiO₂ showed better photocatalytic activity and a more obvious synergistic effect than anatase TiO₂. The addition of free-radical scavengers (tert-butyl alcohol or methanol) inhibited the degradation efficiency of rutile TiO₂, but had a relatively minor effect on anatase TiO₂. Fluorescence spectrophotometry analysis indicated that hydroxyl free radicals could be continuously produced when using rutile TiO₂ as the photocatalyst. Degradation of terbuthylazine catalyzed by rutile TiO₂ occurred mainly in solution, but occurred on the particle surface of the photocatalyst when catalyzed by anatase TiO₂. This study provides new insight into the role of TiO₂ crystalline structure on the degradation of terbuthylazine and its photocatalytic degradation mechanism.     

Simulated-sunlight-activated photocatalysis of Methylene Blue using cerium-doped SiO2/TiO2 nanostructured fibers

Cerium-doped SiO₂/TiO₂ nanostructured fibers were fabricated by electrospinning technology. The prepared fibers were characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Using the fibers as catalysts, photocatalytic degradation of Methylene Blue (MB) aqueous solution was carried out under simulated sunlight. The 0.2% Ce doping proved to be the optimal concentration for the doping of TiO₂/SiO₂, compared to other Ce-doped molar concentrations. The 0.2% Ce-doped SiO₂/TiO₂ fibers exhibited higher photocatalytic activity than industrial Degussa P25 and the samples doped with only Ce or SiO₂. The reasons for improving the photocatalytic activity were also discussed. Several operational parameters were studied, which showed that the photocatalytic efficiency of MB was influenced by parameters such as the initial dye concentration, the initial pH, inorganic anions, and so on. In addition, the influences of an electron acceptor and a radical scavenger suggested that OH was the dominant photooxidant during the photocatalytic process. The reuse evaluation of the fibers indicated that their photocatalytic activity had good stability.     

Biofilm response and removal via the coupling of visible-light-driven photocatalysis and biodegradation in an environment of sulfamethoxazole and Cr(VI)

The widespread contamination of water systems with antibiotics and heavy metals has gained much attention. Intimately coupled visible -light-responsive photocatalysis and biodegradation (ICPB) provides a novel approach for removing such mixed pollutants. In ICPB, the photocatalysis products are biodegraded by a protected biofilm, leading to the mineralization of refractory organics. In the present study, the ICPB approach exhibited excellent photocatalytic activity and biodegradation, providing up to ∼1.27 times the degradation rate of sulfamethoxazole (SMX) and 1.16 times the Cr(VI) reduction rate of visible-light-induced photocatalysis . Three-dimensional fluorescence analysis demonstrated the synergistic ICPB effects of photocatalysis and biodegradation for removing SMX and reducing Cr(VI). In addition, the toxicity of the SMX intermediates and Cr(VI) in the ICPB process significantly decreased. The use of MoS₂/CoS₂ photocatalyst accelerated the separation of electrons and holes, with•O₂^– and h⁺ attacking SMX and e^– reducing Cr(VI), providing an effective means for enhancing the removal and mineralization of these mixed pollutants via the ICPB technique. The microbial community results demonstrate that bacteria that are conducive to pollutant removal are were enriched by the acclimation and ICPB operation processes, thus significantly improving the performance of the ICPB system.     

Effect of transition metal doping under reducing calcination atmosphere on photocatalytic property of TiO2 immobilized on SiO2 beads

TiO₂ immobilized on SiO₂ (TiO₂/SiO₂) have been prepared by sol-gel method and various ions of transition metals (Cr³⁺, Co²⁺, Ni²⁺, Cu²⁺, and Zn²⁺) were doped on the photocatalyst using wet impregnation method under reducing calcination atmosphere. The photocatalytic activity of metal doped TiO₂/SiO₂ towards phenol degradation under black light irradiation were investigated and compared with undoped TiO₂/SiO₂. The results showed that the photoresponse of Cu²⁺ and Zn²⁺ doped TiO₂/SiO₂ were larger than undoped TiO₂/SiO₂, indicating that the photogenerated carriers were separated more efficiently in Cu²⁺ and Zn²⁺ doped TiO₂/SiO₂. The reactivity was in the order of Cu²⁺ > Zn²⁺ > Ni²⁺ > Cr³⁺ > Co²⁺. The different photoreactivity was ascribed to combine effect of the different ionic radii and photocorrison tendency of the dopants. The sample was also characterized by surface analytical methods such as X-ray diffraction, scanning electron micrograph/electron dispersive X-ray analyzer and UV-Vis absorption spectrum.     

Rubber sheet strewn with TiO2 particles:Photocatalytic activity and recyclability

A new method for the preparation of rubber sheet strewn with titanium dioxide particles (TiO₂-strewn sheet) is presented. This simple and low cost method is based on the use of TiO₂ powder (Degussa P25) being strewn onto the sheet made from rubber latex (60% HA) through a steel sieve. The characteristic of the TiO₂-strewn sheet was studied by using scanning electron microscopy/energy dispersive X-ray spectrometer (SEM/EDS) and X-ray diffractometer (XRD) techniques. The photocatalytic activity of TiO₂-strewn rubber sheet was evaluated using Indigo Carmine (IC) dye as a model for organic dye pollutant in water. The results showed that the TiO₂-strewn sheet could degrade IC dye solution under UV light irradiation. The effects of pH, initial concentration, and the intensity of UV light on the photodegradation were also investigated. Kinetics of the photocatalytic degradation was of the first-order reaction. The used TiO₂-strewn sheet can be recovered and reused. The recycling uses did not require any cleaning between successive uses and no decline in the photodegradation efficiency was observed compared with freshly prepared TiO₂-strewn sheet.     

Nb_2O_5 nanowires in-situ grown on carbon fiber: A high-efficiency material for the photocatalytic reduction of Cr(Ⅵ)

Niobium oxide nanowire-deposited carbon fiber(CF) samples were prepared using a hydrothermal method with amorphous Nb_2O_5·nH_2O as precursor. The physical properties of the samples were characterized by means of numerous techniques, including X-ray diffraction(XRD), energy-dispersive spectroscopy(EDS), scanning electron microscopy(SEM), transmission electron microscopy(TEM), selected-area electron diffraction(SAED), UV–visible spectroscopy(UV–vis), N_2 adsorption–desorption, Fourier transform infrared spectroscopy(FT-IR), and X-ray photoelectron spectroscopy. The efficiency for the removal of Cr(VI) was determined.Parameters such as pH value and initial Cr(VI) concentration could influence the Cr(VI) removal efficiency or adsorption capacity of the Nb_2O_5/carbon fiber sample obtained after hydrothermal treatment at 160°C for 14 hr. The maximal Cr(VI) adsorption capacity of the Nb_2O_5 nanowire/CF sample was 115 mg/g. This Nb_2O_5/CF sample also showed excellent photocatalytic activity and stability for the reduction of Cr(VI) under UV-light irradiation: the Cr(VI) removal efficiency reached 99.9% after UV-light irradiation for 1 hr and there was no significant decrease in photocatalytic performance after the use of the sample for 10 repeated cycles. Such excellent Cr(VI) adsorption capacity and photocatalytic performance was related to its high surface area,abundant surface hydroxyl groups, and good UV-light absorption ability.     

Acid-assisted hydrothermal synthesis of nanocrystalline TiO2 from titanate nanotubes: Influence of acids on the photodegradation of gaseous toluene

In order to efficiently remove volatile organic compounds (VOCs) from indoor air, onedimensional titanate nanotubes (TiNTs) were hydrothermally treated to prepare TiO₂ nanocrystals with different crystalline phases, shapes and sizes. The influences of various acids such as CH₃COOH, HNO₃, HCl, HF and H₂SO₄ used in the treatment were separately compared to optimize the performance of the TiO₂ nanocrystals. Comparedwith the strong and corrosive inorganic acids, CH₃COOH was not only safer andmore environmentally friendly, but also more efficient in promoting the photocatalytic activity of the obtained TiO₂. Itwasobserved that the anatase TiO₂ synthesized in 15 mol/L CH₃COOH solution exhibited the highest photodegradation rate of gaseous toluene (94%), exceeding that of P25 (44%) by a factor ofmore than two. The improved photocatalytic activity was attributed to the small crystallite size and surface modification by CH₃COOH. The influence of relative humidity (20%-80%) on the performance of TiO₂ nanocrystals was also studied. The anatase TiO₂ synthesized in 15 mol/L CH₃COOH solution was more tolerant tomoisture than the other TiO₂ nanocrystals and P25.     

Photocatalytic performance and dispersion stability of nanodispersed TiO2 hydrosol in electrolyte solutions with different cations

The existence of electrolytes in aquatic environment on the photocatalytic performance and coagulation of nanodispersed TiO₂ hydrosol and the corresponding photocatalytic alteration were investigated by studying cations (Na⁺, K⁺, Ca ²⁺, Mg²⁺, and Al³⁺). The photocatalysis reactions of nano TiO₂ with different dosages of electrolytes were measured by monitoring the degradation of Rhodamine B (RhB) under ultraviolet A (UV-A) irradiation over time. The results showed that the photocatalytic performance of TiO₂ was improved by the presence of Al³⁺, while the performance was impaired by the other tested cations. The negative influences of divalent ions on the photocatalytic performance of TiO₂ were more significant than monovalent ions. The TiO₂ sol dispersed stable at nano scale at low concentration of electrolyte (< 0.01?mol/L) with slight change of pH, and coagulated into micro sizes at high concentration of electrolytes (> 0.1?mol/L) with larger increase or decrease of pH. The positive effects of Al³⁺ on the photodegradation rate of RhB might relate to the strong hydrolytic action of Al³⁺ in aquatic solutions. The photocatalytic processes of TiO₂ in the presence of all ions followed the Langmuir-Hinshelwood model, and the reaction kinetic constant was increased with the decrease of pH caused by different cations. These work suggested a new perspective about the relationship between coagulation and photocatalytic performance of TiO₂ hydrosols in electrolyte with hydrolysable cations, which demonstrated that TiO₂ hydrosols may be suitable as photocatalysts in aquatic environments.     

Photocatalytic degradation of paraquat using nano-sized Cu-TiO2/SBA-15 under UV and visible light

Photocatalytic degradation of paraquat using mesoporous-assembled Cu-TiO₂/SBA15 under UV and visible light was investigated. The catalyst was synthesized by impregnation of Cu-TiO₂ colloids onto SBA-15. The colloids of Cu-TiO₂ were prepared via sol-gel method while the mesoporous support was prepared using hydrothermal technique. The catalyst was characterized using X-ray diffraction, nitrogen adsorption-desorption, transmission electron microscopy, UV diffuse reflectance spectroscopy, Zeta potential and X-ray adsorption spectroscopy. Results from characterizations showed that Cu doped TiO₂ had a small crystalline size and was well-dispersed on SBA-15. The inclusion of SBA-15 significantly enhanced the photocatalytic activity of the catalyst. Among the three types of undoped catalyst in this study (P25, TiO₂, TiO₂/SBA-15), TiO₂/SBA-15 yielded the highest degradation of paraquat for all pH under UV illumination. Meanwhile 2 wt.% Cu-TiO₂/SBA-15 yielded the highest activity under visible light.     

Photocatalytic degradation of organochlorine compounds using TiO2 supported on fiberglass cloth

The feasibility of photocatalytic degradation of organochlorine compounds using TiO₂ supported on fiberglass cloth as a photocatalyst was studied. The results showed that 2.0×10^-4 mol/dm³ of dichloroethylene, trichloroethylene and tetrachloroethylene can be completely photocatalytically degraded within a short time under illumination with a 375W medium pressure mercury lamp. The effects of parameters such as illumination time, initial concentration of organochlorine compounds, amount of air flow and concentration of H₂O₂ on the photocatalytic degradation were investigated. The TiO₂ supported on the fiberglass was not easily detached and after 500h illumination there was no significant loss of photocatalytic activity of TiO₂. The passible mechanisms of photocatalytic degradation were discussed.     

Dielectric barrier discharge plasma-assisted modification of g-C3N4/Ag2O/TiO2-NRs composite enhanced photoelectrocatalytic activity

Dielectric barrier discharge (DBD) plasma applied as surface treatment technology was employed for the modification of Ag₂O and graphitic carbon nitride (g-C₃N₄) powders. Subsequently, the pretreated powders were sequentially loaded onto TiO₂ nanorods (TiO₂-NRs) via electro-deposition, followed by calcination at N₂ atmosphere. The results indicated that at the optimal plasma discharge time of 5 min for modification of g-C₃N₄ and Ag₂O, photocurrent density of ternary composite was 6 times to bare TiO₂-NRs under UV-visible light irradiation. Phenol was degraded by using DBD plasma-modified g-C₃N₄/Ag₂O/TiO₂-NRs electrode to analyze the photoelectrocatalytic performance. The removal rate of phenol for g-C₃N₄-5/Ag₂O-5/TiO₂-NRs electrode was about 3.07 times to that for TiO₂-NRs electrode. During active species scavengers’ analysis, superoxide radicals and hydroxyl radicals were the main oxidation active species for pollutants degradation. A possible electron-hole separation and transfer mechanism of ternary composite with high photoelectrocatalytic performance was proposed.     

Photocatalytic reduction of Cr(VI) over cinder-based nanoneedle in presence of tartaric acid: Synergistic performance and mechanism

Cr(VI) is a common heavy metal ion, which will seriously harm human body and environment. Therefore, the removal of Cr(VI) has become an attractive topic. In this work, cinder was used as a raw material to synthesize a nanoneedle material: γ-([email protected]) (γ[email protected]). The physicochemical properties of γ[email protected] were thoroughly characterized, and its effectiveness as a catalyst for photocatalytic reduction of Cr(VI) was evaluated. The results showed that Cr(VI) could be efficiently reduced by γ[email protected] in the presence of tartaric acid (TA) under visible light. The variable factors on the reaction were investigated in detail, and the results showed that under optimal conditions (γ[email protected] 0.4 g/L, TA 0.6 g/L, pH 2), Cr(VI) was completely reduced within 7 min. Besides, scavenger experiments and EPR proved that O₂^{? —} and CO₂^{? —} played a significant role in the photocatalytic reduction of Cr(VI). TA acts as a sacrificial agent to trap the holes and generate strong reducing free radicals: CO₂^{? —}. Dissolving O₂ could react with electrons to generate O₂^{? —}. This work discussed the performance and mechanism of photocatalytic reduction of Cr(VI) in detail, which provided a new idea for the resource utilization of solid waste and the treatment of heavy metal sewage.     

Enhanced solar-light-driven photocatalytic properties of novel Z-scheme binary BiPO4 nanorods anchored onto NiFe2O4 nanoplates: Efficient removal of toxic organic pollutants

Global environmental problems have been increasing with the growth of the world economy and have become a crucial issue. To replace fossil fuels, sustainable and eco-friendly catalysts are required for the removal of organic pollutants. In this study, nickel ferrite (NiFe₂O₄) was prepared using a simple wet-chemical synthesis, followed by calcination; bismuth phosphate (BiPO₄) was also prepared using a hydrothermal method. Further, NiFe₂O₄/BiPO₄ nanocomposites were prepared using a hydrothermal technique. Numerous characterization studies, such as structural, morphology, surface area, optical, photoluminescence, and photoelectrochemical investigations, were used to analyze NiFe₂O₄/BiPO₄ nanocomposites. The morphology analysis indicated a successful decoration of BiPO₄ nanorods on the surface of NiFe₂O₄ nanoplate. Further, the bandgap of the NiFe₂O₄/BiPO₄ nanocomposites was modified owing to the formation of a heterostructure. The as-prepared NiFe₂O₄/BiPO₄ nanocomposite exhibited promising properties to be used as a novel heterostructure for tetracycline (TC) and Rhodamine B (RhB) removal. The NiFe₂O₄/BiPO₄ nanocomposite degrades TC (98%) and RhB (99%) pollutants upon solar-light irradiation within 100 and 60 min, respectively. Moreover, the trapping experiments confirmed the Z-scheme approach of the prepared nanocomposites. The efficient separation and transfer of photogenerated electron-hole pairs rendered by the heterostructure were confirmed by utilizing electrochemical impedance spectroscopy, photocurrent experiments, and photoluminescence. Mott–Schottky measurements were used determine the positions of the conduction and valence bands of the samples, and the detailed mechanism of photocatalytic degradation of toxic pollutants was projected and discussed.     

Performance and mechanism of Cr(VI) removal by zero-valent iron loaded onto expanded graphite

Zero-valent iron (ZVI) was loaded on expanded graphite (EG) to produce a composite material (EG-ZVI) for efficient removal of hexavalent chromium (Cr(VI)). EG and EG-ZVI were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Fourier-transform infrared (FTIR) spectroscopy and Brunauer–Emmett–Teller (BET) analysis. EG-ZVI had a high specific surface area and contained sub-micron sized particles of zero-valent iron. Batch experiments were employed to evaluate the Cr(VI) removal performance. The results showed that the Cr(VI) removal rate was 98.80% for EG-ZVI, which was higher than that for both EG (10.00%) and ZVI (29.80%). Furthermore, the removal rate of Cr(VI) by EG-ZVI showed little dependence on solution pH within a pH range of 1–9. Even at pH 11, a Cr(VI) removal rate of 62.44% was obtained after reaction for 1 hr. EG-ZVI could enhance the removal of Cr(VI) via chemical reduction and physical adsorption, respectively. X-ray photoelectron spectroscopy (XPS) was used to analyze the mechanisms of Cr(VI) removal, which indicated that the ZVI loaded on the surface was oxidized, and the removed Cr(VI) was immobilized via the formation of Cr(III) hydroxide and Cr(III)–Fe(III) hydroxide/oxyhydroxide on the surface of EG-ZVI.