Wintertime PM2.5 and PM10 Source Apportionment at Sacramento,California

ABSTRACT

The chemical mass balance (CMB) model was applied to winter (November through January) 1991–1996 PM2.5 and PM10 data from the Sacramento 13th and T Streets site in order to identify the contributions from major source categories to peak 24-hr ambient PM_2.5 and PM₁₀ levels. The average monthly PM₁₀ monitoring data for the nine-year period in Sacramento County indicate that elevated concentrations are typical in the winter months. Concentrations on days of highest PM₁₀ are dominated by the PM2.5 fraction. One factor contributing to increased PM_2.5 concentrations in the winter is meteorology (cool temperatures, low wind speeds, low inversion layers, and more humid conditions) that favors the formation of secondary nitrate and sulfate aerosols. Residential wood burning also elevates fine particulate concentrations in the Sacramento area.

The results of the CMB analysis highlight three key points. First, the source apportionment results indicate that primary motor vehicle exhaust and wood smoke are significant sources of both PM_2.5 and PM₁₀ in winter. Second, nitrates, secondarily formed as a result of motor-vehicle and other sources of nitrogen oxide (NO_x), are another principal cause of the high PM_2.5 and PM₁₀ levels during the winter months. Third, fugitive dust, whether it is resuspended soil and dust or agricultural tillage, is not the major contributor to peak winter PM_2.5 and PM10 levels in the Sacramento area.     

Modeling air quality during the California Regional PM10/PM2.5 Air Quality Study (CPRAQS) using the UCD/CIT source-oriented air quality model – Part III. Regional source apportionment of secondary and total airborne particulate matter

A comprehensive air quality modeling project was carried out to simulate regional source contributions to secondary and total (=primary + secondary) airborne particle concentrations in California's Central Valley. A three-week stagnation episode lasting from December 15, 2000 to January 7, 2001, was chosen for study using the air quality and meteorological data collected during the California Regional PM₁₀/PM_2.5 Air Quality Study (CRPAQS). The UCD/CIT mechanistic air quality model was used with explicit decomposition of the gas phase reaction chemistry to track source contributions to secondary PM. Inert artificial tracers were used with an internal mixture representation to track source contributions to primary PM. Both primary and secondary source apportionment calculations were performed for 15 size fractions ranging from 0.01 to 10 μm particle diameters. Primary and secondary source contributions were resolved for fugitive dust, road dust, diesel engines, catalyst equipped gasoline engines, non-catalyst equipped gasoline engines, wood burning, food cooking, high sulfur fuel combustion, and other anthropogenic sources.Diesel engines were identified as the largest source of secondary nitrate in central California during the study episode, accounting for approximately 40% of the total PM_2.5 nitrate. Catalyst equipped gasoline engines were also significant, contributing approximately 20% of the total secondary PM_2.5 nitrate. Agricultural sources were the dominant source of secondary ammonium ion. Sharp gradients of PM concentrations were predicted around major urban areas. The relative source contributions to PM_2.5 from each source category in urban areas differ from those in rural areas, due to the dominance of primary OC in urban locations and secondary nitrate in the rural areas. The source contributions to ultra-fine particle mass PM_0.1 also show clear urban/rural differences. Wood smoke was found to be the major source of PM_0.1 in urban areas while motor vehicle sources were the major contributor of PM_0.1 in rural areas, reflecting the influence from two major highways that transect the Valley.     

Particulate matter,nitrogen oxides,ozone, and select volatile organic compounds during a winter sampling period in Logan,Utah, USA

Particulate matter mass (PM), trace gaseous pollutants, and select volatile organic compounds (VOCs) with meteorological variables were measured in Logan, Utah (Cache Valley), for >4 weeks during winter 2017 as part of the Utah Winter Fine Particle Study (UWFPS). Higher PM levels for short time periods and lower ozone (O₃) levels were present due to meteorological and mountain valley conditions. Nitrogenous pollutants were relatively strongly correlated with PM variables. Diurnal cycles of NO_x, O₃, and fine PM(PM 2.5) (aerodynamic diameter <2.5 μm [PM_2.5]) suggested formation from NO_x. O₃ levels increased from early morning into midafternoon, and NO_x and PM_2.5 increased throughout the morning, followed by sharp decreases. Toluene/benzene and xylenes/benzene ratios and VOC correlations with nitrogenous and PM species were indicative of local traffic sources. Wind sector comparisons suggested that pollutant levels were lower when winds were from nearby mountains to the east versus winds from northerly or southerly origins.

Implications: The Cache Valley in Idaho and Utah has been designated a PM_2.5 nonattainment area that has been attributed to air pollution buildup during winter stagnation events. To inform state implementation plans for PM_2.5 in Cache Valley and other PM_2.5 nonattainment areas in Utah, a state and multiagency federal research effort known as the UWFPS was conducted in winter 2017. As part of the UWFPS, the U.S. Environmental Protection Agency (EPA) measured ground-based PM species and their precursors, VOCs, and meteorology in Logan, Utah. Results reported here from the EPA study in Logan provide additional understanding of wintertime air pollution conditions and possible sources of PM and gaseous pollutants as well as being useful for future PM control strategies in this area.     

The Steubenville Comprehensive Air Monitoring Program (SCAMP): Analysis of Short-Term and Episodic Variations in PM2.5 Concentrations Using Hourly Air Monitoring Data

Abstract

One-hour average ambient concentrations of particulate matter (PM) with an aerodynamic diameter <2.5 μm (PM_2.5) were determined in Steubenville, OH, between June 2000 and May 2002 with a tapered element oscillating microbalance (TEOM). Hourly average gaseous copollutant [carbon monoxide (CO), sulfur dioxide (SO₂), nitrogen oxide (NO_x), and ozone (O₃)] concentrations and meteorological conditions also were measured. Although 75% of the 14,682 hourly PM_2.5 concentrations measured during this period were ≤17 μg/m³, concentrations >65 μg/m³ were observed 76 times. On average, PM_2.5 concentrations at Steubenville exhibited a diurnal pattern of higher early morning concentrations and lower afternoon concentrations, similar to the diurnal profiles of CO and NO_x. This pattern was highly variable; however, PM_2.5 concentrations >65 μg/m³ were never observed during the mid-afternoon between 1:00 p.m. and 5:00 p.m. EST. Twenty-two episodes centered on one or more of these elevated concentrations were identified. Five episodes occurred during the months June through August; the maximum PM_2.5 concentration during these episodes was 76.6 μg/m³. Episodes occurring during climatologically cooler months often featured higher peak concentrations (five had maximum concentrations between 95.0 and 139.6 μg/m³), and many exhibited strong covariation between PM_2.5 and CO, NO_x, or SO₂. Case studies suggested that nocturnal surface-based temperature inversions were influential in driving high nighttime concentrations of these species during several cool season episodes, which typically had dramatically lower afternoon concentrations. These findings provide insights that may be useful in the development of PM_2.5 reduction strategies for Steubenville, and suggest that studies assessing possible health effects of PM_2.5 should carefully consider exposure issues related to the intraday timing of PM_2.5 episodes, as well as the potential for toxicological interactions among PM_2.5 and primary gaseous pollutants.     

A study on variations of concentrations of particulate matter with different sizes in Lanzhou,China

Lanzhou is one of the most air-polluted cities in China and in the world, and its primary air pollutant is particulate matter (PM). Different size particulate matter (TSP, PM₁₀, PM_2.5 and PM_1.0) have different sources and affect the environment and human health differently, so it is very important to study the pollutant characteristics of different particles in order to deeply understand the pollution situation of Lanzhou city and establish reasonable preventive countermeasures. TSP, PM₁₀, PM_2.5 and PM_1.0 concentrations were simultaneously measured in Lanzhou to detect the annual and diurnal variations of concentrations of PM with different sizes and possible causes. The main results are as follows: (1) The annual distribution of monthly average concentrations for coarse particles (TSP and PM₁₀) is bimodal with the highest peak in April, which is different from the situation in other cities not affected by sand-dust events. However, the annual distribution for fine particles (PM_2.5 and PM_1.0) is unimodal with the peak in December. This difference between coarse and fine particles indicates that sand-dust events in spring carry much more coarse than fine particles to Lanzhou. This result is supported by the correlation between springtime wind speed and concentrations of PM with different sizes. (2) Under normal conditions (without dust intrusions), the diurnal distribution of coarse particle concentration in Lanzhou is bimodal. However, the distribution is trimodal during dust intrusions in April, with an extra peak in the afternoon. (3) In general, the highest concentration peaks of the diurnal variations for TSP, PM₁₀, PM_2.5 and PM_1.0 occur at about the same time. However, there are obvious differences in the occurrence time of the minimum concentrations among different kinds of PM. The differences in the occurrence time of minima between coarse and fine particles are due to their different diffusion behaviors in the atmospheric boundary layer.     

Particulate air quality model predictions using prognostic vs. diagnostic meteorology in central California

Comparisons were made between three sets of meteorological fields used to support air quality predictions for the California Regional Particulate Air Quality Study (CRPAQS) winter episode from December 15, 2000 to January 6, 2001. The first set of fields was interpolated from observations using an objective analysis method. The second set of fields was generated using the WRF prognostic model without data assimilation. The third set of fields was generated using the WRF prognostic model with the four-dimensional data assimilation (FDDA) technique. The UCD/CIT air quality model was applied with each set of meteorological fields to predict the concentrations of airborne particulate matter and gaseous species in central California. The results show that the WRF model without data assimilation over-predicts surface wind speed by ～30% on average and consequently yields under-predictions for all PM and gaseous species except sulfate (S(VI)) and ozone(O₃). The WRF model with FDDA improves the agreement between predicted and observed wind and temperature values and consequently yields improved predictions for all PM and gaseous species. Overall, diagnostic meteorological fields produced more accurate air quality predictions than either version of the WRF prognostic fields during this episode. Population-weighted average PM_2.5 exposure is 40% higher using diagnostic meteorological fields compared to prognostic meteorological fields created without data assimilation. These results suggest diagnostic meteorological fields based on a dense measurement network are the preferred choice for air quality model studies during stagnant periods in locations with complex topography.     

Codependencies of Reactive Air Toxic and Criteria Pollutants on Emission Reductions

Abstract

It is important to understand the effects of emission controls on concentrations of ozone, fine particulate matter (PM_2.5), and hazardous air pollutants (HAPs) simultaneously, to evaluate the full range of health, ecosystem, and economic effects. Until recently, the capability to simultaneously evaluate interrelated atmospheric pollutants (“one atmosphere” analysis) was unavailable to air quality managers. In this work, we use an air quality model to examine the potential effect of three emission reductions on concentrations of ozone, PM_2.5, and four important HAPs (formaldehyde, acetaldehyde, acrolein, and benzene) over a domain centered on Philadelphia for 12-day episodes in July and January 2001. Although NO_x controls are predicted to benefit PM_2.5 concentrations and sometimes benefit ozone, they have only a small effect on formaldehyde, slightly increase acetaldehyde and acrolein, and have no effect on benzene in the July episode. Concentrations of all pollutants except benzene increase slightly with NO_x controls in the January simulation. Volatile organic compound controls alone are found to have a small effect on ozone and PM_2.5, a less than linear effect on decreasing aldehydes, and an approximately linear effect on acrolein and benzene in summer, but a slightly larger than linear effect on aldehydes and acrolein in winter. These simulations indicate the difficulty in assessing how toxic air pollutants might respond to emission reductions aimed at decreasing criteria pollutants such as ozone and PM_2.5.     

Trends in primary particulate matter emissions from Canadian agriculture

Particulate matter (PM) has long been recognized as an air pollutant due to its adverse health and environmental impacts. As emission of PM from agricultural operations is an emerging air quality issue, the Agricultural Particulate Matter Emissions Indicator (APMEI) has been developed to estimate the primary PM contribution to the atmosphere from agricultural operations on Census years and to assess the impact of practices adopted to mitigate these emissions at the soil landscape polygon scale as part of the agri-environmental indicator report series produced by Agriculture and Agri-Food Canada. In the APMEI, PM emissions from animal feeding operations, wind erosion, land preparation, crop harvest, fertilizer and chemical application, grain handling, and pollen were calculated and compared for the Census years of 1981–2006. In this study, we present the results for PM₁₀ and PM_2.5, which exclude chemical application and pollen sources as they only contribute to total suspended particles. In 2006, PM emissions from agricultural operations were estimated to be 652.6 kt for PM₁₀ and 158.1 kt for PM_2.5. PM emissions from wind erosion and land preparation account for most of PM emissions from agricultural operations in Canada, contributing 82% of PM₁₀ and 76% of PM_2.5 in 2006. Results from the APMEI show a strong reduction in PM emissions from agricultural operations between 1981 and 2006, with a decrease of 40% (442.8 kt) for PM₁₀ and 47% (137.7 kt) for PM_2.5. This emission reduction is mainly attributed to the adoption of conservation tillage and no-till practices and the reduction in the area of summerfallow land.

Implications: Increasing sustainability in agriculture often means adapting management practices to have a beneficial impact on the environment while maintaining or increasing production and economic benefits. We developed an inventory of primary PM emissions from agriculture in Canada to better quantify the apportionment, spatial distribution, and trends for Census years 1981–2006. We found major reductions of 40% in PM₁₀ and 47% in PM_2.5 emissions over the 25-yr period as a co-benefit of increasing carbon sequestration in agricultural soils. Indeed, farmers adopted conservation tillage/no-till practices, increased usage of cover crops, and reduced summerfallow, in order to increase soil organic matter and reduce carbon dioxide emissions, which also reduced primary PM emissions, although the agricultural production increased over the period.     

Source apportionment of airborne particulate matter in Southeast Texas using a source-oriented 3D air quality model

A nested version of the source-oriented externally mixed UCD/CIT model was developed to study the source contributions to airborne particulate matter (PM) during a two-week long air quality episode during the Texas 2000 Air Quality Study (TexAQS 2000). Contributions to primary PM and secondary ammonium sulfate in the Houston–Galveston Bay (HGB) and Beaumont–Port Arthur (BPA) areas were determined.The predicted 24-h elemental carbon (EC), organic compounds (OC), sulfate, ammonium ion and primary PM_2.5 mass are in good agreement with filter-based observations. Predicted concentrations of hourly sulfate, ammonium ion, and primary OC from diesel and gasoline engines and biomass burning organic aerosol (BBOA) at La Porte, Texas agree well with measurements from an Aerodyne Aerosol Mass Spectrometer (AMS).The UCD/CIT model predicts that EC is mainly from diesel engines and majority of the primary OC is from internal combustion engines and industrial sources. Open burning contributes large fractions of EC, OC and primary PM_2.5 mass. Road dust, internal combustion engines and industries are the major sources of primary PM_2.5. Wildfire dominates the contributions to all primary PM components in areas near the fires. The predicted source contributions to primary PM are in general agreement with results from a chemical mass balance (CMB) model. Discrepancy between the two models suggests that further investigations on the industrial PM emissions are necessary.Secondary ammonium sulfate accounts for the majority of the secondary inorganic PM. Over 80% of the secondary sulfate in the 4 km domain is produced in upwind areas. Coal combustion is the largest source of sulfate. Ammonium ion is mainly from agriculture sources and contributions from gasoline vehicles are significant in urban areas.     

Development of a PM2 5 Emissions Inventory for the South Coast Air Basin

ABSTRACT

With the promulgation of a national PM_2.5 ambient air quality standard, it is important that PM_2.5 emissions inventories be developed as a tool for understanding the magnitude of potential PM2.5 violations. Current PM₁₀ inventories include only emissions of primary particulate matter (1 ^ï PM), whereas, based on ambient measurements, both PM₁₀ and PM2.5 emissions inventories will need to include sources of both 1^ï PM and secondary particulate matter (2^ï PM). Furthermore, the U. S. Environmental Protection Agency’s (EPA) current edition of AP-42 includes size distribution data for 1o PM that overestimate the PM_2.5 fraction of fugitive dust sources by at least a factor of 2 based on recent studies.

This paper presents a PM_2.5 emissions inventory developed for the South Coast Air Basin (SCAB) that for the first time includes both 1^ï PM and 2^ï PM. The former is calculated by multiplying PM₁₀ emissions estimates by the PM_2.5/PM₁₀ ratios for different sources. The latter is calculated from estimated emission rates of gas-phase aerosol precursor and gas to aerosol conversion rates consistent with the measured chemical composition of ambient PM_2.5 concentrations observed in the SCAB. The major finding of this PM_2.5 emissions inventory is that the ^2ï aerosol component is more than twice the ^1ï aerosol component, which may result in widely different control strategies being required for fine PM and coarse PM.     

Daily Mortality and Air Pollution in the Netherlands

ABSTRACT

We studied the association of daily mortality with short-term variations in the ambient concentrations of major gaseous pollutants and PM in the Netherlands. The magnitude of the association in the four major urban areas was compared with that in the remainder of the country. Daily cause-specific mortality counts, air quality, temperature, relative humidity, and influenza data were obtained from 1986 to 1994. The relationship between daily mortality and air pollution was modeled using Poisson regression analysis. We adjusted for potential confounding due to long-term and seasonal trends, influenza epidemics, ambient temperature and relative humidity, day of the week, and holidays, using generalized additive models.

Influenza episodes were associated with increased mortality up to 3 weeks later. Daily mortality was significantly associated with the concentration of all air pollutants. An increase in the PM₁₀ concentration by 100 u.g/m³ was associated with a relative risk (RR) of 1.02 for total mortality. The largest RRs were found for pneumonia deaths. Ozone had the most consistent, independent association with mortality. Particulate air pollution (e.g., PM₁₀, black smoke [BS]) was not more consistently associated with mortality than were the gaseous pollutants SO₂ and NO₂. Aerosol SO₄ ^-2, NO₃ ^-, and BS were more consistently associated with total mortality than was PM₁₀. The RRs for all pollutants were substantially larger in the summer months than in the winter months. The RR of total mortality for PM₁₀ was 1.10 for the summer and 1.03 for the winter. There was no consistent difference between RRs in the four major urban areas and the more rural areas.     

Daily Mortality in the Philadelphia Metropolitan Area and Size-Classified Particulate Matter

ABSTRACT

Time-series of daily mortality data from May 1992 to September 1995 for various portions of the seven-county Philadelphia, PA, metropolitan area were analyzed in relation to weather and a variety of ambient air quality parameters. The air quality data included measurements of size-classified PM, SO₄ ^2-, and H+ that had been collected by the Harvard School of Public Health, as well as routine air pollution monitoring data. Because the various pollutants of interest were measured at different locations within the metropolitan area, it was necessary to test for spatial sensitivity by comparing results for different combinations of locations. Estimates are presented for single pollutants and for multiple-pollutant models, including gaseous pollutants and mutually exclusive components of PM (PM_2.5 and coarse particles, SO₄ ^2- and non-SO₄ ^2- portions of total suspended particulate [TSP] and PM₁₀), measured on the day of death and the previous day.

We concluded that associations between air quality and mortality were not limited to data collected in the same part of the metropolitan area; that is, mortality for one part may be associated with air quality data from another, not necessarily neighboring, part. Significant associations were found for a wide variety of gaseous and particulate pollutants, especially for peak O₃. Using joint regressions on peak O₃ with various other pollutants, we found that the combined responses were insensitive to the specific other pollutant selected. We saw no systematic differences according to particle size or chemistry. In general, the associations between daily mortality and air pollution depended on the pollutant or the PM metric, the type of collection filter used, and the location of sampling. Although peak O₃ seemed to exhibit the most consistent mortality responses, this finding should be confirmed by analyzing separate seasons and other time periods.     

Recent spatial gradients and time trends in Dhaka,Bangladesh, air pollution and their human health implications

Dhaka, the capital of Bangladesh, is among the most polluted cities in the world. This research evaluates seasonal patterns, day-of-week patterns, spatial gradients, and trends in PM_2.5 (<2.5 µm in aerodynamic diameter), PM₁₀ (<10 µm in aerodynamic diameter), and gaseous pollutants concentrations (SO₂, NO₂, CO, and O₃) monitored in Dhaka from 2013 to 2017. It expands on past work by considering multiple monitoring sites and air pollutants. Except for ozone, the average concentrations of these pollutants showed strong seasonal variation, with maximum during winter and minimum during monsoon, with the pollution concentration of PM_2.5 and PM₁₀ being roughly five- to sixfold higher during winter versus monsoon. Our comparisons of the pollutant concentrations with Bangladesh NAAQS and U.S. NAAQS limits analysis indicate particulate matter (PM_2.5 and PM₁₀) as the air pollutants of greatest concern, as they frequently exceeded the Bangladesh NAAQS and U.S. NAAQS, especially during nonmonsoon time. In contrast, gaseous pollutants reported far fewer exceedances throughout the study period. During the study period, the highest number of exceedances of NAAQS limits in Dhaka City (Darus-Salam site) were found for PM_2.5 (72% of total study days), followed by PM₁₀ (40% of total study days), O₃ (1.7% of total study days), SO₂ (0.38% of total study days), and CO (0.25% of total study days). The trend analyses results showed statistically significant positive slopes over time for SO₂ (5.6 ppb yr^?1, 95% confidence interval [CI]: 0.7, 10.5) and CO (0.32 ppm yr^?1, 95% CI: 0.01, 0.56), which suggest increase in brick kilns operation and high-sulfur diesel use. Though statistically nonsignificant annual decreasing slopes for PM_2.5 (?4.6 µg/m³ yr^?1, 95% CI: ?12.7, 3.6) and PM₁₀ (?2.7 µg/m³ yr^?1, 95% CI: ?7.9, 2.5) were observed during this study period, the PM_2.5 concentration is still too high (~ 82.0 µg/m³) and can cause severe impact on human health.

Implications: This study revealed key insights into air quality challenges across Dhaka, Bangladesh, indicating particulate matter (PM) as Dhaka’s most serious air pollutant threat to human health. The results of these analyses indicate that there is a need for immediate further investigations, and action based on those investigations, including the conduct local epidemiological PM exposure-human health effects studies for this city, in order to determine the most public health effective interventions.     

Monitoring of sources and atmospheric processes controlling air quality in an urban Mediterranean environment

Different monitoring parameters (PM mass concentrations, number–size distribution, black carbon, gaseous pollutants, and chemical composition, among others) are currently used in air quality studies. Urban aerosols are the result of several sources and atmospheric processes, which suggests that a single monitoring technique is insufficient to quantitatively evaluate all of them.This study assesses the suitability of a number of monitoring techniques (PM mass concentrations, number and size distribution of ultra-fine particles, levels of gaseous pollutants, and a complete chemical characterization of PM₁₀ and PM_2.5) by examining the response of those techniques to the different emission sources and/or atmospheric processes affecting an urban Mediterranean area (Barcelona, NE Spain).The results of this work reveal that the PM mass, the number concentration and the chemical composition give different, but complementary, information. Whereas the mineral matter, a key atmospheric aerosol component across the Mediterranean, is not properly quantitatively assessed by measuring sub-micrometric particles, the monitoring of the number concentration is indispensable to interpret the origin of specific aerosol episodes. Furthermore, the chemical composition yields very relevant information to deduce the causes of specific pollution episodes.The number concentration of ultra-fine particles in urban areas is strongly dependent upon vehicle exhaust emissions, which may cause adverse health impacts. Moreover, urban Mediterranean environments are favourable to produce nucleation-mode particles (<20 nm) with photochemical origin. In those cases, these particles are expected to be of high solubility and consequently their toxicity may differ from that of traffic-generated ultra-fine particles. Thus, the use of a single monitoring parameter to evaluate the health effects seems to be not enough.     

Characterization of Particulate Matter in California

ABSTRACT

The size, composition, and concentration of particulate matter (PM) vary with location and time. Several monitoring/sampling programs are operated in California to characterize PM less than 2.5 and 10 µm in aerodynamic diameter (PM_2.5 and PM₁₀). This paper presents a broad summary of the spatial and temporal variations observed in ambient PM_2.5 and PM₁₀ concentrations in California. Many areas that have high PM₁₀ concentrations also have relatively high PM_2.5 concentrations, and data indicate that a significant portion of the PM₁₀ air quality problem is caused by PM_2.5. To develop effective plans for attaining the ambient PM standards, improved understanding of these unique problems is needed. Since 1989, pollution control efforts—whether specifically targeted for particulate matter or indirectly via controls on gaseous emissions—have caused annual average PM_2.5 and PM₁₀ concentrations to decline at most sites in California.     

Windblown Dust Contributes to High PM25 Concentrations

ABSTRACT

The revised National Ambient Air Quality Standards for PM include fine particulate standards based upon mass measurements of PM₂₅. It is possible in arid and semi-arid regions to observe significant coarse mode intrusion in the PM_2.5 measurement. In this work, continuous PM₁₀, PM_2.5, and PM_1.0 were measured during several windblown dust events in Spokane, WA. PM_{2 5} constituted ~30% of the PM₁₀ during the dust event days, compared with ~48% on the non-dusty days preceding the dust events. Both PM₁₀ and PM_2.5 were enhanced during the dust events. However, PM_1.0 was not enhanced during dust storms that originated within the state of Washington. During a dust storm that originated in Asia and impacted Spokane, PM_1.0 was also enhanced, although the Asian dust reached Washington during a period of stagnation and poor dispersion, so that local sources were also contributing to high particulate levels. The “intermodal” region of PM, defined as particles ranging in aerodynamic size from 1.0 to 2.5 um, was found to represent a significant fraction of PM₂₅ (~51%) during windblown dust events, compared with 28% during the non-dusty days before the dust events.     

A wintertime PM2.5 episode at the Fresno,CA, supersite

A winter PM_2.5 episode that achieved a maximum 24-h average of 138 μg m⁻³ at the Fresno Supersite in California's San Joaquin Valley between 2 and 12 January, 2000 is examined using 5-min to 1-h continuous measurements of mass, nitrate, black carbon, particle-bound PAH, and meteorological measurements. Every day PM_2.5 sampling showed that many episodes, including this one, are missed by commonly applied sixth-day monitoring, even though quarterly averages and numbers of US air quality standard exceedances are adequately estimated. Simultaneous measurements at satellite sites show that the Fresno Supersite represented PM_2.5 within the city, and that half or more of the urban concentrations were present at distant, non-urban locations unaffected by local sources. Most of the primary particles accumulated during early morning and nighttime, decreasing when surface temperatures increased and the shallow radiation inversion coupled to a valleywide layer. When this coupling occurred, nitrate levels increased rapidly over a 10–30 min period as black carbon and gaseous concentrations dropped. This is consistent with a conceptual model in which secondary aerosol forms above the surface layer and is effectively decoupled from the surface for all but the late-morning and early afternoon period. Primary pollutants, such as organic and black carbon, accumulate within the shallow surface layer in urban areas where wood burning and vehicle exhaust emissions are high. Such a model would explain why earlier studies find nitrate concentrations to be nearly the same among widely separated sites in urban areas, as winds aloft of 1 to 6 m s⁻¹ could easily disperse the elevated aerosol throughout the valley.     

Temporal variations of fine and coarse particulate matter sources in Jeddah,Saudi Arabia

This study provides the first comprehensive analysis of the seasonal variations and weekday/weekend differences in fine (aerodynamic diameter <2.5 μm; PM_2.5) and coarse (aerodynamic diameter 2.5–10 μm; PM_2.5–10) particulate matter mass concentrations, elemental constituents, and potential source origins in Jeddah, Saudi Arabia. Air quality samples were collected over 1 yr, from June 2011 to May 2012 at a frequency of three times per week, and analyzed. The average mass concentrations of PM_2.5 (21.9 μg/m³) and PM₁₀ (107.8 μg/m³) during the sampling period exceeded the recommended annual average levels by the World Health Organization (WHO) for PM_2.5 (10 μg/m³) and PM₁₀ (20 μg/m³), respectively. Similar to other Middle Eastern locales, PM_2.5–10 is the prevailing mass component of atmospheric particulate matter at Jeddah, accounting for approximately 80% of the PM₁₀ mass. Considerations of enrichment factors, absolute principal component analysis (APCA), concentration roses, and backward trajectories identified the following source categories for both PM_2.5 and PM_2.5–10: (1) soil/road dust, (2) incineration, and (3) traffic; and for PM_2.5 only, (4) residual oil burning. Soil/road dust accounted for a major portion of both the PM_2.5 (27%) and PM_2.5–10 (77%) mass, and the largest source contributor for PM_2.5 was from residual oil burning (63%). Temporal variations of PM_2.5–10 and PM_2.5 were observed, with the elevated concentration levels observed for mass during the spring (due to increased dust storm frequency) and on weekdays (due to increased traffic). The predominant role of windblown soil and road dust in both the PM_2.5 and PM_2.5–10 masses in this city may have implications regarding the toxicity of these particles versus those in the Western world where most PM health assessments have been made in the past. These results support the need for region-specific epidemiological investigations to be conducted and considered in future PM standard setting.

Implications: Temporal variations of fine and coarse PM mass, elemental constituents, and sources were examined in Jeddah, Saudi Arabia, for the first time. The main source of PM_2.5–10 is natural windblown soil and road dust, whereas the predominant source of PM_2.5 is residual oil burning, generated from the port and oil refinery located west of the air sampler, suggesting that targeted emission controls could significantly improve the air quality in the city. The compositional differences point to a need for health effect studies to be conducted in this region, so as to directly assess the applicability of the existing guidelines to the Middle East air pollution.     

Development,Evaluation, and Application of a Primary Aerosol Model

ABSTRACT

The Segmented-Plume Primary Aerosol Model (SPPAM) has been developed over the past several years. The earlier model development goals were simply to generalize the widely used Industrial Source Complex Short-Term (ISCST) model to simulate plume transport and dispersion under light wind conditions and to handle a large number of roadway or line sources. The goals have been expanded to include development of improved algorithm for effective plume transport velocity, more accurate and efficient line and area source dispersion algorithms, and recently, a more realistic and computationally efficient algorithm for plume depletion due to particle dry deposition. A performance evaluation of the SPPAM has been carried out using the 1983 PNL dual tracer experimental data. The results show the model predictions to be in good agreement with observations in both plume advection-dispersion and particulate matter (PM) depletion by dry deposition. For PM_2.5 impact analysis, the SPPAM has been applied to the Rubidoux area of California. Emission sources included in the modeling analysis are: paved road dust, diesel vehicular exhaust, gasoline vehicular exhaust, and tire wear particles from a large number of roadways in Rubidoux and surrounding areas. For the selected modeling periods, the predicted primary PM_2.5 to primary PM10 concentration ratios for the Rubidoux sampling station are in the range of 0.39–0.46. The organic fractions of the primary PM_2.5 impacts are estimated to be at least 34–41%. Detailed modeling results indicate that the relatively high organic fractions are primarily due to the proximity of heavily traveled roadways north of the sampling station. The predictions are influenced by a number of factors; principal among them are the receptor locations relative to major roadways, the volume and composition of traffic on these roadways, and the prevailing meteorological conditions.