Hydroxyl radical intensified Cu2O NPs/H2O2 process in ceramic membrane reactor for degradation on DMAc wastewater from polymeric membrane manufacturer

• Cu₂O NPs/H₂O₂ Fenton process was intensified by membrane dispersion. • DMAc removal was enhanced to 98% for initial DMAc of 14000 mg/L. • Analyzed time-resolved degradation pathway of DMAc under ·OH attack. High-concentration industrial wastewater containing N,N-dimethylacetamide (DMAc) from polymeric membrane manufacturer was degraded in Cu₂O NPs/H₂O₂ Fenton process. In the membrane-assisted Fenton process DMAc removal rate was up to 98% with 120 min which was increased by 23% over the batch reactor. It was found that ·OH quench time was extended by 20 min and the maximum ·OH productivity was notably 88.7% higher at 40 min. The degradation reaction rate constant was enhanced by 2.2 times with membrane dispersion (k = 0.0349 min⁻¹). DMAc initial concentration (C₀) and H₂O₂ flux (J_p) had major influence on mass transfer and kinetics, meanwhile, membrane pore size (r_p) and length (L_m) also affected the reaction rate. The intensified radical yield, fast mass transfer and nanoparticles high activity all contributed to improve pollutant degradation efficiency. Time-resolved DMAc degradation pathway was analyzed as hydroxylation, demethylation and oxidation leading to the final products of CO₂, H₂O and NO₃⁻ (rather than NH₃ from biodegradation). Continuous process was operated in the dual-membrane configuration with in situ reaction and separation. After five cycling tests, DMAc removal was all above 95% for the initial [DMAc]₀ = 14,000 mg/L in wastewater and stability of the catalyst and the membrane maintained well.     

A Cu-modified active carbon fiber significantly promoted H2S and PH3 simultaneous removal at a low reaction temperature

• Cu_0.15-ACF performs the best for H₂S and PH₃ simultaneous removal. • 550°C and 90°C are separately calcination and reaction temperatures. • The reason why Cu_0.15/ACF shows better performance was found. • The accumulation of H₂PO₄⁻ and SO₄²⁻(H₂O)₆ is the deactivation cause of Cu_0.15/ACF. Poisonous gases, such as H₂S and PH₃, produced by industrial production harm humans and damage the environment. In this study, H₂S and PH₃ were simultaneously removed at low temperature by modified activated carbon fiber (ACF) catalysts. We have considered the active metal type, content, precursor, calcination, and reaction temperature. Experimental results exhibited that ACF could best perform by loading 15% Cu from nitrate. The optimized calcination temperature and reaction temperature separately were 550°C and 90°C. Under these conditions, the most removal capacity could reach 69.7 mg/g and 132.1 mg/g, respectively. Characterization results showed that moderate calcination temperature (550°C) is suitable for the formation of the copper element on the surface of ACF, lower or higher temperature will generate more cuprous oxide. Although both can exhibit catalytic activity, the role of the copper element is significantly greater. Due to the exceptional dispersibility of copper (oxide), the ACF can still maintain the advantages of larger specific surface area and pore volume after loading copper, which is the main reason for better performance of related catalysts. Finally, increasing the copper loading amount can significantly increase the crystallinity and particle size of copper (oxide) on the ACF, thereby improving its catalytic performance. In situ IR found that the reason for the deactivation of the catalyst should be the accumulation of generated H₂PO₄⁻ and SO₄²⁻(H₂O)₆ which could poison the catalyst.     

Oxidation and biotoxicity assessment of microcystin-LR using different AOPs based on UV,O3 and H2O2

MC-LR removal performances under different AOPs were compared systematically. Higher removal efficiency and synergistic effects were obtained by combined process. The acute biotoxicity raised in different degrees after oxidation. Microcystin-LR attracts attention due to its high toxicity, high concentration and high frequency. The removal characteristics of UV/H₂O₂ and O₃/H₂O₂ advanced oxidation processes and their individual process for MC-LR were investigated and compared in this study. Both the removal efficiencies and rates of MC-LR as well as the biotoxicity of degradation products was analyzed. Results showed that the UV/H₂O₂ process and O₃/H₂O₂ were effective methods to remove MC-LR from water, and they two performed better than UV-, O₃-, H₂O₂-alone processes under the same conditions. The effects of UV intensity, H₂O₂ concentration and O₃ concentration on the removal performance were explored. The synergistic effects between UV and H₂O₂, O₃ and H₂O₂ were observed. UV dosage of 1800 mJ·cm⁻² was required to remove 90% of 100 mg·L⁻¹ MC-LR, which amount significantly decreased to 500 mJ·cm⁻² when 1.7 mg·L⁻¹ H₂O₂ was added. 0.25 mg·L⁻¹ O₃, or 0.125 mg·L⁻¹ O₃ with 1.7 mg·L⁻¹ H₂O₂ was needed to reach 90% removal efficiency. Furthermore, the biotoxicity results about these UV/H₂O₂, O₃/H₂O₂ and O₃-alone processes all present rising trends with oxidation degree of MC-LR. Biotoxicity of solution, equivalent to 0.01 mg·L⁻¹ Zn²⁺, raised to 0.05 mg·L⁻¹ Zn²⁺ after UV/H₂O₂ or O₃/H₂O₂ reaction. This phenomenon may be attributed to the aldehydes and ketones with small molecular weight generated during reaction. Advice about the selection of MC-LR removal methods in real cases was provided.     

Catalytic urea hydrolysis by composite metal oxide catalyst towards efficient urea-based SCR process: performance evaluation and mechanism investigation

● Bimetallic oxide composite catalyst was designed for the urea-based SCR process. ● Surface chemical state and typical microstructure of catalyst was determined. ● Reaction route was improved based on intermediates and active site identification. ● TiO₂@Al₂O₃ presents an obvious promotion for urea hydrolysis. As a promising option to provide gaseous NH₃ for SCR system, catalytic urea hydrolysis has aroused great attention, and improving surface area and activity of catalysis are the crucial issues to be solved for efficient urea hydrolysis. Therefore, a composite metal oxide (TiO₂@Al₂O₃) catalyst was prepared by a simple hydrothermal method, with mesoporous alumina (γ-Al₂O₃) as substrate. The results verify the mesoporous structure and submicron cluster of TiO₂@Al₂O₃, with exposed crystal faces of (101) and (400) for TiO₂ and γ-Al₂O₃, respectively. The electronegativity difference of Ti⁴⁺ and Al³⁺ changes the charge distribution scheme around the interface, which provides abundant acid/base sites to boost the urea hydrolysis. Consequently, for an optimal proportioning with nano TiO₂ content at 10 wt.%, the hydrolysis efficiency can reach up to 35.2 % at 100 °C in 2 h, increasing by ~7.1 % than that of the blank experiment. ¹³C NMR spectrum measurements provide the impossible intermediate species during urea hydrolysis. Theoretical calculations are performed to clarify the efficient H₂O decomposition at the interface of TiO₂@Al₂O₃. The result offers a favorable technology for energy-efficiency urea hydrolysis.     

Catalytic hydrolysis of gaseous HCN over Cu–Ni/γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst: parameters and conditions

To decompose efficiently hydrogen cyanide (HCN) in exhaust gas, g-Al₂O₃-supported bimetallicbased Cu–Ni catalyst was prepared by incipient-wetness impregnation method. The effects of the calcination temperature, H₂O/HCN volume ratio, reaction temperature, and the presence of CO or O₂ on the HCN removal efficiency on the Cu–Ni/g-Al₂O₃ catalyst were investigated. To examine further the efficiency of HCN hydrolysis, degradation products were analyzed. The results indicate that the HCN removal efficiency increases and then decreases with increasing calcination temperature and H₂O/HCN volume ratio. On catalyst calcined at 400°C, the efficiency reaches a maximum close to 99% at 480 min at a H₂O/HCN volume ratio of 150. The HCN removal efficiency increases with increasing reaction temperature within the range of 100°C–500°C and reaches a maximum at 500°C. This trend may be attributed to the endothermicity of HCN hydrolysis; increasing the temperature favors HCN hydrolysis. However, the removal efficiencies increases very few at 500°C compared with that at 400°C. To conserve energy in industrial operations, 400°C is deemed as the optimal reaction temperature. The presence of CO facilitates HCN hydrolysis andincreases NH₃ production. O₂ substantially increases the HCN removal efficiency and NO _x production but decreases NH₃ production.

Open image in new window

     

NiB2O4 (B = Mn or Co) catalysts for NH3-SCR of NOx at low-temperature in microwave field

● Microwave-assisted catalytic NH₃-SCR reaction over spinel oxides is carried out. ● SCR reaction temperature is tremendously lowered in microwave field. ● NO conversion of NiMn₂O₄ is highly up to 90.6% at 70°C under microwave heating. Microwave-assisted selective catalytic reduction of nitrogen oxides (NO_x) was investigated over Ni-based metal oxides. The NiMn₂O₄ and NiCo₂O₄ catalysts were synthesized by the co-precipitation method and their activities were evaluated as potential candidate catalysts for low-temperature NH₃-SCR in a microwave field. The physicochemical properties and structures of the catalysts were characterized by X-ray diffraction (XRD), Scanning electron microscope (SEM), N₂-physisorption, NO adsorption-desorption in the microwave field, H₂-temperature programmed reduction (H₂-TPR) and NH₃-temperature programmed desorption (NH₃-TPD). The results verified that microwave radiation reduced the reaction temperature required for NH₃-SCR compared to conventional heating, which needed less energy. For the NiMn₂O₄ catalyst, the catalytic efficiency exceeded 90% at 70 °C and reached 96.8% at 110 °C in the microwave field. Meanwhile, the NiMn₂O₄ also exhibited excellent low-temperature NH₃-SCR reaction performance under conventional heating conditions, which is due to the high BET specific surface area, more suitable redox property, good NO adsorption-desorption in the microwave field and rich acidic sites.     

Evaluation of the technoeconomic feasibility of electrochemical hydrogen peroxide production for decentralized water treatment

• Gas diffusion electrode (GDE) is a suitable setup for practical water treatment. • Electrochemical H₂O₂ production is an economically competitive technology. • High current efficiency of H₂O₂ production was obtained with GDE at 5–400 mA/cm². • GDE maintained high stability for H₂O₂ production for ~1000 h. • Electro-generation of H₂O₂ enhances ibuprofen removal in an E-peroxone process. This study evaluated the feasibility of electrochemical hydrogen peroxide (H₂O₂) production with gas diffusion electrode (GDE) for decentralized water treatment. Carbon black-polytetrafluoroethylene GDEs were prepared and tested in a continuous flow electrochemical cell for H₂O₂ production from oxygen reduction. Results showed that because of the effective oxygen transfer in GDEs, the electrode maintained high apparent current efficiencies (ACEs,>80%) for H₂O₂ production over a wide current density range of 5–400 mA/cm², and H₂O₂ production rates as high as ~202 mg/h/cm² could be obtained. Long-term stability test showed that the GDE maintained high ACEs (>85%) and low energy consumption (<10 kWh/kg H₂O₂) for H₂O₂ production for 42 d (~1000 h). However, the ACEs then decreased to ~70% in the following 4 days because water flooding of GDE pores considerably impeded oxygen transport at the late stage of the trial. Based on an electrode lifetime of 46 days, the overall cost for H₂O₂ production was estimated to be ~0.88 $/kg H₂O₂, including an electricity cost of 0.61 $/kg and an electrode capital cost of 0.27 $/kg. With a 9 cm² GDE and 40 mA/cm² current density, ~2–4 mg/L of H₂O₂ could be produced on site for the electro-peroxone treatment of a 1.2 m³/d groundwater flow, which considerably enhanced ibuprofen abatement compared with ozonation alone (~43%–59% vs. 7%). These findings suggest that electrochemical H₂O₂ production with GDEs holds great promise for the development of compact treatment technologies for decentralized water treatment at a household and community level.     

Optimization of the O3/H2O2 process with response surface methodology for pretreatment of mother liquor of gas field wastewater

• Real ML-GFW with high salinity and high organics was degraded by O₃/H₂O₂ process. • Successful optimization of operation conditions was attained using RSM based on CCD. • Single-factor experiments in advance ensured optimal experimental conditions. • The satisfactory removal efficiency of TOC was achieved in spite of high salinity. • The initial pH plays the most significant role in the degradation of ML-GFW. The present study reports the use of the O₃/H₂O₂ process in the pretreatment of the mother liquor of gas field wastewater (ML-GFW), obtained from the multi-effect distillation treatment of the gas field wastewater. The range of optimal operation conditions was obtained by single-factor experiments. Response surface methodology (RSM) based on the central composite design (CCD) was used for the optimization procedure. A regression model with Total organic carbon (TOC) removal efficiency as the response value was established (R² = 0.9865). The three key factors were arranged according to their significance as: pH>H₂O₂ dosage>ozone flow rate. The model predicted that the best operation conditions could be obtained at a pH of 10.9, an ozone flow rate of 0.8 L/min, and H₂O₂ dosage of 6.2 mL. The dosing ratio of ozone was calculated to be 9.84 mg O₃/mg TOC. The maximum removal efficiency predicted was 75.9%, while the measured value was 72.3%. The relative deviation was found to be in an acceptable range. The ozone utilization and free radical quenching experiments showed that the addition of H₂O₂ promoted the decomposition of ozone to produce hydroxyl radicals (·OH). This also improved the ozone utilization efficiency. Gas chromatography-mass spectrometry (GC-MS) analysis showed that most of the organic matters in ML-GFW were degraded, while some residuals needed further treatment. This study provided the data and the necessary technical supports for further research on the treatment of ML-GFW.     

Ce0.7Zr0.3O2纳米棒的制备及其对柴油车尾气碳颗粒的催化净化性能

本研究以硝酸铈、硝酸锆为原料使用溶剂热合成法,制备了CeO₂-ZrO₂纳米棒催化剂(Ce_0.7Zr_0.3O₂(NR)),并用于柴油车尾气碳颗粒催化净化.催化活性检测证实:Ce_0.7Zr_0.3O₂(NR)纳米棒催化剂可有效净化柴油车尾气碳烟颗粒.在Ce_0.7Zr_0.3O₂(NR)存在下,碳颗粒净化率为10%、50%和90%时,所需温度分别仅为375℃、414℃和455℃,比商用Ce_0.7Zr_0.3O₂和Ce0.3Zr0.7O2催化剂性能更优.采用氮吸附-脱附、X射线光电子能谱(XPS)、H2程序升温还原(H₂-TPR)、X射线衍射(XRD)、拉曼光谱(Raman)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)等技术对催化剂进行表征.XRD和Raman结果证实,Ce_0.7Zr_0.3O₂(NR)主要由立方相CeO₂构成,并掺杂了少量四方相氧化锆.SEM和TEM结果则显示,Ce_0.7Zr_0.3O₂(NR)催化剂颗粒明显由纳米棒堆积而成,特定的纳米形貌会影响其对碳颗粒的催化氧化活性.XPS结果证明Ce_0.7Zr_0.3O₂(NR)催化剂主要具有晶格氧、化学氧和表面吸附氧等氧物种;晶格氧是碳颗粒氧化的活性氧物种,其溢流到催化剂表面可与碳颗粒接触从而提高反应活性;化学氧和表面吸附氧均为表面氧物种,极易与表面固体碳颗粒直接接触,从而可在较低温度下促进碳颗粒的净化.H₂-TPR结果进一步证实了XPS结果,Ce_0.7Zr_0.3O₂(NR)催化剂的低温还原温度比商用Ce_0.7Zr_0.3O₂催化剂更低,且含有更多的易还原氧物种,这些低温易还原氧物种可以在较低温度下参与催化反应,促进柴油车尾气颗粒物的低温催化净化.     

Size and shape effects of MnFe2O4 nanoparticles as catalysts for reductive degradation of dye pollutants

• Size and shape-dependent MnFe₂O₄ NPs were prepared via a facile method. • Ligand-exchange chemistry was used to prepare the hydrophilic MnFe₂O₄ NPs. • The catalytic properties of MnFe₂O₄ NPs toward dye degradation were fully studied. • The catalytic activities of MnFe₂O₄ NPs followed Michaelis–Menten behavior. • All the MnFe₂O₄ NPs exhibit selective degradation to different dyes. The magnetic nanoparticles that are easy to recycle have tremendous potential as a suitable catalyst for environmental toxic dye pollutant degradation. Rationally engineering shapes and tailoring the size of nanocatalysts are regarded as an effective manner for enhancing performances. Herein, we successfully synthesized three kinds of MnFe₂O₄ NPs with distinctive sizes and shapes as catalysts for reductive degradation of methylene blue, rhodamine 6G, rhodamine B, and methylene orange. It was found that the catalytic activities were dependent on the size and shape of the MnFe₂O₄ NPs and highly related to the surface-to-volume ratio and atom arrangements. Besides, all these nanocatalysts exhibit selectivity to different organic dyes, which is beneficial for their practical application in dye pollutant treatment. Furthermore, the MnFe₂O₄ NPs could be readily recovered by a magnet and reused more than ten times without appreciable loss of activity. The size and shape effects of MnFe₂O₄ nanoparticles demonstrated in this work not only accelerate further understanding the nature of nanocatalysts but also contribute to the precise design of nanoparticles catalyst for pollutant degradation.     

Efficient production of hydrogen peroxide in microbial reverse-electrodialysis cells coupled with thermolytic solutions

● Appreciable H₂O₂ production rate was achieved in MRCs utilizing NH₄HCO₃ solutions. ● Carbon black outperformed activated carbon as the catalyst for H₂O₂ production. ● The optimum carbon black loading for H₂O₂ production on air-cathode was 10 mg/cm². ● The optimum number of cell pairs was determined to be three. ● A maximum power density of 980 mW/m² was produced by MRCs with 5 cell pairs. H₂O₂ was produced at an appreciable rate in microbial reverse-electrodialysis cells (MRCs) coupled with thermolytic solutions, which can simultaneously capture waste heat as electrical energy. To determine the optimal cathode and membrane stack configurations for H₂O₂ production, different catalysts, catalyst loadings and numbers of membrane cell pairs were tested. Carbon black (CB) outperformed activated carbon (AC) for H₂O₂ production, although AC showed higher catalytic activity for oxygen reduction. The optimum CB loading was 10 mg/cm² in terms of both the H₂O₂ production rate and power production. The optimum number of cell pairs was determined to be three based on a tradeoff between H₂O₂ production and capital costs. A H₂O₂ production rate as high as 0.99 ± 0.10 mmol/(L·h) was achieved with 10 mg/cm² CB loading and 3 cell pairs, where the H₂O₂ recovery efficiency was 52 ± 2% and the maximum power density was 780 ± 37 mW/m². Increasing the number of cell pairs to five resulted in an increase in maximum power density (980 ± 21 mW/m²) but showed limited effects on H₂O₂ production. These results indicated that MRCs can be an efficient method for sustainable H₂O₂ production.     

Fe2O3-CeO2-Bi2O3/γ-Al2O3 catalyst in the catalytic wet air oxidation (CWAO) of cationic red GTL under mild reaction conditions

Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃, an environmental friendly material, was investigated. The catalyst exhibited good catalytic performance in the CWAO of cationic red GTL. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. HO₂· and O₂·⁻ appeared as the main reactive species in the reaction. The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst, a novel environmental-friendly material, was used to investigate the catalytic wet air oxidation (CWAO) of cationic red GTL under mild operating conditions in a batch reactor. The catalyst was prepared by wet impregnation, and characterized by special surface area (BET measurement), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The Fe₂O₃-CeO₂-Bi₂O₃/γ-Al₂O₃ catalyst exhibited good catalytic activity and stability in the CWAO under atmosphere pressure. The effect of the reaction conditions (catalyst loading, degradation temperature, solution concentration and initial solution pH value) was studied. The result showed that the decolorization efficiency of cationic red GTL was improved with increasing the initial solution pH value and the degradation temperature. The apparent activation energy for the reaction was 79 kJ·mol⁻¹. Hydroperoxy radicals (HO₂·) and superoxide radicals (O₂⁻·) appeared as the main reactive species upon the CWAO of cationic red GTL.     

CeO2 doping boosted low-temperature NH3-SCR activity of FeTiOx catalyst: A microstructure analysis and reaction mechanistic study

• CeO₂ doping significantly improved low-temperature NH₃-SCR activity on FeTiO_x. • The crystallinity of FeTiO_x was decreased dramatically after CeO₂ doping. • Unique Ce-O-Fe structure in FeCe_0.2TiO_x accounted for its superior redox property. • Facile activation of NH₃ to-NH₂ on FeCe_0.2TiO_x promoted the DeNO_x efficiency. FeTiO_x has been recognized as an environmental-friendly and cost-effective catalyst for selective catalytic reduction (SCR) of NO_x with NH₃. Aimed at further improving the low-temperature DeNO_x efficiency of FeTiO_x catalyst, a simple strategy of CeO₂ doping was proposed. The low-temperature (<250℃) NH₃-SCR activity of FeTiO_x catalyst could be dramatically enhanced by CeO₂ doping, and the optimal composition of the catalyst was confirmed as FeCe_0.2TiO_x, which performed a NO_x conversion of 90% at ca. 200℃. According to X-ray diffraction (XRD), Raman spectra and X-ray absorption fine structure spectroscopy (XAFS) analysis, FeCe_0.2TiO_x showed low crystallinity, with Fe and Ce species well mixed with each other. Based on the fitting results of extended X-ray absorption fine structure (EXAFS), a unique Ce-O-Fe structure was formed in FeCe_0.2TiO_x catalyst. The well improved specific surface area and the newly formed Ce-O-Fe structure dramatically contributed to the improvement of the redox property of FeCe_0.2TiO_x catalyst, which was well confirmed by H₂-temperature-programmed reduction (H₂-TPR) and in situ XAFS experiments. Such enhanced redox capability could benefit the activation of NO and NH₃ at low temperatures for NO_x removal. The detailed reaction mechanism study further suggested that the facile oxidative dehydrogenation of NH₃ to highly reactive-NH₂ played a key role in enhancing the low-temperature NH₃-SCR performance of FeCe_0.2TiO_x catalyst.     

Enhanced 4-chlorophenol biodegradation by integrating Fe2O3 nanoparticles into an anaerobic reactor: Long-term performance and underlying mechanism

• 4-chlorophenol biodegradation could be enhanced in Fe₂O₃ coupled anaerobic system. • Metabolic activity and electron transport could be improved by Fe₂O₃ nanoparticles. • Functional microbial communities could be enriched in coupled anaerobic system. • Possible synergistic mechanism involved in enhanced dechlorination was proposed. Fe₂O₃ nanoparticles have been reported to enhance the dechlorination performance of anaerobic systems, but the underlying mechanism has not been clarified. This study evaluated the technical feasibility, system stability, microbial biodiversity and the underlying mechanism involved in a Fe₂O₃ nanoparticle-coupled anaerobic system treating 4-chlorophenol (4-CP) wastewater. The results demonstrated that the 4-CP and total organic carbon (TOC) removal efficiencies in the Fe₂O₃-coupled up-flow anaerobic sludge blanket (UASB) were always higher than 97% and 90% during long-term operation, verifying the long-term stability of the Fe₂O₃-coupled UASB. The 4-CP and TOC removal efficiencies in the coupled UASB increased by 42.9±0.4% and 27.5±0.7% compared to the control UASB system. Adding Fe₂O₃ nanoparticles promoted the enrichment of species involved in dechlorination, fermentation, electron transfer and acetoclastic methanogenesis, and significantly enhanced the extracellular electron transfer ability, electron transport activity and conductivity of anaerobic sludge, leading to enhanced 4-CP biodegradation performance. A possible synergistic mechanism involved in enhanced anaerobic 4-CP biodegradation by Fe₂O₃ nanoparticles was proposed.     

One-pot hydrothermal fabrication of BiVO4/Fe3O4/rGO composite photocatalyst for the simulated solar light-driven degradation of Rhodamine B

• BiVO₄/Fe₃O₄/rGO has excellent photocatalytic activity under solar light radiation. • It can be easily separated and collected from water in an external magnetic field. • BiVO₄/Fe₃O₄/0.5% rGO exhibited the highest RhB removal efficiency of over 99%. • Hole (h⁺) and superoxide radical (O₂^•−) dominate RhB photo-decomposition process. • The reusability of this composite was confirmed by five successive recycling runs. Fabrication of easily recyclable photocatalyst with excellent photocatalytic activity for degradation of organic pollutants in wastewater is highly desirable for practical application. In this study, a novel ternary magnetic photocatalyst BiVO₄/Fe₃O₄/reduced graphene oxide (BiVO₄/Fe₃O₄/rGO) was synthesized via a facile hydrothermal strategy. The BiVO₄/Fe₃O₄ with 0.5 wt% of rGO (BiVO₄/Fe₃O₄/0.5% rGO) exhibited superior activity, degrading greater than 99% Rhodamine B (RhB) after 120 min solar light radiation. The surface morphology and chemical composition of BiVO₄/Fe₃O₄/rGO were studied by scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, UV–visible diffuse reflectance spectroscopy, Fourier transform infrared spectroscopy, and Raman spectroscopy. The free radicals scavenging experiments demonstrated that hole (h⁺) and superoxide radical (O₂^•−) were the dominant species for RhB degradation over BiVO₄/Fe₃O₄/rGO under solar light. The reusability of this composite catalyst was also investigated after five successive runs under an external magnetic field. The BiVO₄/Fe₃O₄/rGO composite was easily separated, and the recycled catalyst retained high photocatalytic activity. This study demonstrates that catalyst BiVO₄/Fe₃O₄/rGO possessed high dye removal efficiency in water treatment with excellent recyclability from water after use. The current study provides a possibility for more practical and sustainable photocatalytic process.     

Influence of H2S and NH3 on biogas dry reforming using Ni catalyst: a study on single and synergetic effect

● NH₃ in biogas had a slight inhibitory effect on dry reforming. ● Coexistence of H₂S and NH₃ led to faster decline of biogas conversion. ● Regeneration was effective for catalysts deactivated under synergetic effect. Biogas is a renewable biomass energy source mainly composed of CH₄ and CO₂. Dry reforming is a promising technology for the high-value utilization of biogas. Some impurity gases in biogas can not be completely removed after pretreatment, which may affect the performance of dry reforming. In this study, the influence of typical impurities H₂S and NH₃ on dry reforming was studied using Ni/MgO catalyst. The results showed that low concentration of H₂S in biogas could cause serious deactivation of catalyst. Characterization results including EDS, XPS and TOF-SIMS confirmed the adsorption of sulfur on the catalyst surface, which was the cause of catalyst poisoning. We used air calcination method to regenerate the sulfur-poisoned catalysts and found that the regeneration temperature higher than 500 °C could help catalyst recover the original activity. NH₃ in the concentration range of 50–10000 ppm showed a slight inhibitory effect on biogas dry reforming. The decline rate of biogas conversion efficiency increased with the increase of NH₃ concentration. This was related to the reduction of oxygen activity on catalyst surface caused by NH₃. The synergetic effect of H₂S and NH₃ in biogas was investigated. The results showed that biogas conversion decreased faster under the coexistence of H₂S and NH₃ than under the effect of H₂S alone, so as the surface oxygen activity of catalyst. Air calcination regeneration could also recover the activity of the deactivated catalyst under the synergetic effect of H₂S and NH₃.     

A pulsed switching peroxi-coagulation process to control hydroxyl radical production and to enhance 2,4-Dichlorophenoxyacetic acid degradation

• A new pulsed switching peroxi-coagulation (PSPC) system was developed. • The EC_T for 2,4-D removal in the PSPC was lower than that in the EF. • The iron consumption for 2,4-D removal in the PSPC was lower than that in the PC. The aim of this study was to develop a new pulsed switching peroxi-coagulation system to control hydroxyl radical (?OH) production and to enhance 2,4-Dichlorophenoxyacetic acid (2,4-D) degradation. The system was constructed with a sacrifice iron anode, a Pt anode, and a gas diffusion cathode. Production of H₂O₂ and Fe²⁺ was controlled separately by time delayers with different pulsed switching frequencies. Under current densities of 5.0 mA/cm² (H₂O₂) and 0.5 mA/cm² (Fe²⁺), the ?OH production was optimized with the pulsed switching frequency of 1.0 s (H₂O₂):0.3 s (Fe²⁺) and the ratio of H₂O₂ to Fe²⁺ molar concentrations of 6.6. Under the optimal condition, 2,4-D with an initial concentration of 500 mg/L was completely removed in the system within 240 min. The energy consumption for the 2,4-D removal in the system was much lower than that in the electro-Fenton process (68±6 vs. 136±10 kWh/kg TOC). The iron consumption in the system was ~20 times as low as that in the peroxi-coagulation process (196±20 vs. 3940±400 mg/L) within 240 min. The system should be a promising peroxi-coagulation method for organic pollutants removal in wastewater.     

Utilization of nano/micro-size iron recovered from the fine fraction of automobile shredder residue for phenol degradation in water

Phenol removal by n/m Fe in the presence of H₂O₂ was highly effective. Increasing the amounts of n/m Fe and H₂O₂?increased the phenol removal rate. Phenol removal was decreased with an increase in the concentration of phenol. The natural pH (6.9) of the solution was highly effective for phenol removal. The pseudo-first-order kinetics was best fitted for the degradation of phenol. The study investigates the magnetic separation of Fe from automobile shredder residue (ASR) (<0.25 mm) and its application for phenol degradation in water. The magnetically separated Fe was subjected to an ultrasonically assisted acid treatment, and the degradation of phenol in an aqueous solution using nano/micro-size Fe (n/m Fe) was investigated in an effort to evaluate the possibility of utilizing n/m Fe to remove phenol from wastewater. The prepared n/m Fe was analyzed by scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The effects of the dosages of n/mFe, pH, concentration of phenol and amount of H₂O₂ on phenol removal were evaluated. The results confirm that the phenol degradation rate was improved with an increase in the dosages of n/mFe and H₂O₂; however, the rate is reduced when the phenol concentration is higher. The degradation of phenol by n/mFe followed the pseudo-first-order kinetics. The value of the reaction rate constant (k) was increased as the amounts of n/m Fe and H₂O₂ increased. Conversely, the value of k was reduced when the concentration of phenol was increased. The probable mechanism behind the degradation of phenol by n/m Fe is the oxidation of phenol through hydroxyl radicals which are produced during the reaction between H₂O₂ and n/m Fe.     

Decomposition of aqueous chlorinated contaminants by UV irradiation with H2O2

In the present study, the decomposition rates of carbon tetrachloride (CCl₄) and 2,4-dichlorophenol (2,4-DCP) in water by the ultraviolet (UV) light irradiation alone and H₂O₂/UV were experimentally investigated. The detailed experimental studies have been conducted for examining treatment capacities of the two different ultraviolet light sources (low and medium pressure Hg arc) in H₂O₂/UV processes. The low or medium UV lamp alone resulted in a 60%–90% decomposition of 2,4-DCP while a slight addition of H₂O₂ resulted in a drastic enhancement of the 2,4-DCP decomposition rate. The decomposition rate of 2,4-DCP with the medium pressure UV lamp alone was about 3–6 times greater than the low pressure UV lamp alone. In the direct photolysis of aqueous CCl₄, the medium pressure UV lamp had advantage over the low pressure UV lamp because the molar extinction coefficient of CCl₄ at shorter wavelength (210–220 nm) is about 20 to 50 times higher than that at 254 nm. However, adding H₂O₂ to the medium pressure UV lamp system rendered a negative oxidation rate because H₂O₂ acted as a UV absorber being competitive with CCl₄ due to negligible reaction between CCl₄ and OH radicals. The results from the present study indicated significant influence of the photochemical properties of the target contaminants on the photochemical treatment characteristics for designing cost-effective UV-based degradation of toxic contaminants.     

Augmented hydrogen production by gasification of ball milled polyethylene with Ca(OH)2 and Ni(OH)2

PE ball milling pretreatment induces higher H₂ production and purity by gasification. Ca(OH)₂ reacts at solid state with PE boosting H₂ and capturing CO₂. Ca(OH)₂ significantly reduces methanation side-reaction. Polymer thermal recycling for hydrogen production is a promising process to recover such precious element from plastic waste. In the present work a simple but efficacious high energy milling pre-treatment is proposed to boost H₂ generation during polyethylene gasification. The polymer is co-milled with calcium and nickel hydroxides and then it is subjected to thermal treatment. Results demonstrate the key role played by the calcium hydroxide that significantly ameliorates hydrogen production. It reacts in solid state with the polyethylene to form directly carbonate and hydrogen. In this way, the CO₂ is immediately captured in solid form, thus shifting the equilibrium toward H₂ generation and obtaining high production rate (>25 L/mol CH₂). In addition, high amounts of the hydroxide prevent excessive methane formation, so the gas product is almost pure hydrogen (~95%).