Diffusion of oxygen through activated sludge flocs: experimental measurement, modeling, and implications for simultaneous nitrification and denitrification.

Diffusion of dissolved oxygen through activated sludge flocs was studied, as it represents a potential mechanism for simultaneous nitrification and denitrification in activated sludge systems. Dissolved oxygen profiles through six floc particles collected at different times from a full-scale activated sludge plant demonstrated that that the dissolved oxygen concentration declines through all floc particles. For larger floc particles (2-mm diameter and greater), the dissolved oxygen concentration reached near-zero values at depths depending on process operating conditions. A mathematical model based on diffusion of dissolved oxygen, organic substrate (methanol), ammonia, nitrite, and nitrate through a spherical floc and consumption of dissolved oxygen by heterotrophs and autotrophs accurately predicted the dissolved oxygen profile and required adjustment of only one model parameter--the concentration of heterotrophs. A different dissolved oxygen decline pattern was exhibited for the smaller floc particles characterized, with the dissolved oxygen reaching a non-zero plateau toward the center of the floc. This pattern was not reproduced with the mathematical model developed and suggests that additional mechanisms are responsible for the transport of dissolved oxygen into the center of these flocs. Implications of these results regarding the occurrence of simultaneous nitrification and denitrification include consideration of the factors that affect floc size and distribution (simultaneous nitrification and denitrification is maximized with larger floc particles), coupling of the International Water Association (London) activated models to predict activated sludge composition with diffusion models to consider intrafloc effects, and the effects of substrate diffusion on the apparent half-saturation constant for various substrates in activated sludge systems.     

Identifying different types of bulking in an activated sludge system through quantitative image analysis

The present study proposes an image analysis methodology for the identification of different types of disturbances in wastewater treatment activated sludge systems. Up to date, most reported image analysis methodologies have been used in activated sludge processes with the aim of filamentous bulking detection, however, other disturbances could be foreseen in wastewater treatment plants. Such disturbances can lead to fluctuations in the biomass contents, affecting the mixed liquor suspended solids (MLSS), and in the sludge settling ability, affecting the sludge volume index (SVI). Therefore, this work focuses on predicting the MLSS and SVI parameters for different types of disturbances affecting an activated sludge system. Four experiments were conducted simulating filamentous bulking, zoogleal or viscous bulking, pinpoint floc formation, and normal operating conditions. Alongside the MLSS and SVI determination, the aggregated and filamentous biomass contents and morphology were studied as well as the biomass Gram and viability status, by means of image analysis.     

Environmental scanning electron microscopy as a new technique to determine the hygroscopic behaviour of individual aerosol particles

The hygroscopic behaviour of NaCl, (NH₄)₂SO₄, Na₂SO₄ and NH₄NO₃ particles in the size range of 0.1–20 μm was studied by environmental scanning electron microscopy (ESEM). This technique allows the in-situ observation of individual aerosol particles while changing the temperature and/or relative humidity (RH) in the sample chamber. The hygroscopic behaviour of these particles (e.g., deliquescence, adsorption of water on the particle surface) becomes directly observable with a lateral resolution of the order of 8–15 nm. The deliquescence relative humidities (DRH) of the different salts, the temperature dependence of the DRH for NH₄NO₃, and the growth factors (at increasing relative humidities) for NaCl were determined. Generally, a good agreement between the values obtained by ESEM and those found in literature was achieved. However, the DRH of NaCl determined by ESEM is systematically higher (approximately 2%, absolute) than the values obtained by other techniques, which can be explained by the observed strong absorption of water onto the crystal surface prior to droplet formation. The efflorescence behaviour of individual particles can be studied only qualitatively due to influences of the sample substrate. Furthermore, it is demonstrated that the activation of soot can be studied at high resolution by ESEM.     

絮体破碎再形成行为的计算机模拟

为了深入探讨絮体破碎行为对其分形成长及结构的影响,借助一种简化的絮体破碎模式对絮体破碎/再形成过程进行计算机模拟。通过对比分析破碎前后虚拟絮体的形态特征及其统计特性,得出如下主要结论：（1）絮体发生破碎后,所形成碎片的形态特征直接影响着再形成絮体的形态及恢复程度;（2）絮体外围枝杈结构的破坏,有利于运动粒子进入絮体内部或者均匀地排列在凝聚核周围,改善絮体质心附近颗粒的空间分布,从而有效地提高其致密性和抗剪切破坏能力;（3）在絮体分形成长过程中,存在一个使其由各向同性向各向异性过渡的临界状态,之后发育良好的枝杈对其余枝杈生长的抑制作用增强。此外,在实际操作时还应严格控制絮凝体系的物化条件,不宜使絮体过度破碎,以获得较好的絮凝效果。     

Effects of sludge properties on the thickening and dewatering of waste activated sludge.

The thickening and dewatering of waste activated sludge, from a pilot-scale submerged membrane bioreactor and two bench-scale, complete-mix activated sludge reactors (high-shear and low-shear aeration) treating the same municipal primary effluent, were investigated. Solids settling and compaction were measured using the diluted sludge volume index (DSVI) analysis and a batch centrifugation analysis, respectively. Elevated levels of filamentous microorganisms resulted in higher DSVI values and lower centrifuged pellet concentration. Elevated levels of nocardioform bacteria resulted in lower solids float concentrations, and higher colloidal material reduced solids recovery in batch flotation experiments. Sludge filterability, measured as time-to-filter, was shown to be a function of extracelluar polymeric substances and colloidal material, where higher levels of either reduced sludge filterability. Additional research is necessary to confirm these results using full- or demonstration-scale thickening and dewatering units.     

湿法净化黑烟中添加剂对炭黑沉降性能的影响

湿法净化黑烟中炭黑颗粒物的关键在于降低吸收液的表面张力并以高性能絮凝剂使其从溶液中絮凝、沉降以利于分离。选用十六烷基三甲基溴化胺(CTAB)为主要表面活性剂,使之与十二烷基苯磺酸钠(SDBS)和月桂醇聚氧乙烯(9)醚(AEO-9)进行复配实验,研究了复配液的表面张力,再向最低表面张力的复配表面活性剂溶液中投加絮凝剂聚合氯化铝(PAC)和聚丙烯酰胺(PAM),探讨絮凝剂的添加对黑烟颗粒沉降和絮凝的影响.实验结果表明:同时添加表面活性剂CTAB,SDBS和PAC,并使之浓度分别为0.5 mmol/L,0.4 mmol/L和200 mg/L时,炭黑颗粒的沉降效果最好,沉降率高达94%,且絮凝体较大,沉降时间仅为2 min。     

Mineralization of dinitrotoluenes and trinitrotoluene of spent acid in toluene nitration process by Fenton oxidation

Fenton's reagent, UV/H2O2 and UV/Fenton's reagent were employed to mineralize dinitrotoluene (DNT) isomers and 2,4,6-trinitrotoluene (TNT) of spent acid in toluene nitration process. The bench-scale experiments were conducted to elucidate the influence of various operating variables on the performance of removal of total organic compounds (TOC) from spent acid, including reaction temperature, concentration of ferrous ion and H2O2 dosage. It is remarkable that organic compounds were completely mineralized by Fenton oxidation, of which removal efficiency is superior to that of UV/H2O2. Nevertheless, it makes slight difference between Fenton oxidation and UV/Fenton oxidation. According to the spectra identified by gas chromatograph/mass spectrometer (GC/MS), it is proposed that oxidative degradation of DNT isomers leads to o-, m-, p-mononitrotoluene (MNT) and 1,3-dinitrobenzene respectively. Besides, the oxidation of 2,4,6-TNT gives the 1,3,5-trinitrobenzene intermediate. Apparently, Fenton oxidation is promising for purification of spent acid industrially.     

A Modular Approach to A Microcomputer Monitoring System

Abstract

Under a cooperative agreement with the U.S. Environmental Protection Agency's (USEPA) Superfund Innovative Technology Evaluation (SITE) Emerging Technology Program, COGNIS, Inc. conducted bench-scale studies on the COGNIS TERRAMET® Lead Extraction Process. The process leaches, or extracts, lead from contaminated soil and consists of a lead leaching stage followed by recovery of the dissolved lead from the leachant. Prior to treatment, the soil is characterized, the type and extent of lead contamination is identified, and the soil is pretreated by physical separation methods to facilitate the extraction process. The physical pretreatment, for example, may include particle size separation to allow separate leaching of the sand and fines fractions and removal of larger lead particles by density separation techniques. As part of the SITE Program, COGNIS investigated seven different lead-contaminated soil samples in small bench-scale batch studies and three soils in larger bench-scale continuous-treatment studies. This bench-scale work led to the design, construction, and operation of a full-scale treatment plant by COGNIS at the Twin Cities Army Ammunition Plant (TCAAP), New Brighton, MN where lead and seven other heavy metals were extracted and recovered from over 20,000 tons of treated soil to meet cleanup criteria.     

New tabletop SEM-EDS-based approach for cost-efficient monitoring of airborne particulate matter

Recent developments in scanning electron microscopy (SEM) have produced tabletop instruments capable of reasonable imaging resolution at less cost compared to conventional equipment. Combining the SEM with energy dispersive spectroscopy (EDS) allows the possibility of elemental analysis through detection of X-rays emitted from interaction between individual particles and the SEM electron beam, revealing their atomic composition. It’s well known that exposure to inhalable particulate matter (PM) poses health risks and routine monitoring of the chemical content of these has been realized. Exposure information is of a general character but by combining the chemical build-up of monitored particles and knowledge of their inherent health effects will allow better risk assessment. An analysis technique using a tabletop SEM with EDS is demonstrated on particles collected onto nucleopore filters from urban, industrial and rural areas. Detailed characterization of the instruments analysis capabilities as applied to PM are described.     

钙离子对短期膜污染的影响

以处理生活污水的平板膜-生物反应器为依托,通过将进水调配成30、200和500 mg/L 3种不同的钙离子浓度,考察钙离子对短期膜污染的影响。结果表明,随着钙离子浓度的增加,TMP增长趋势变小,膜污染得到缓解;钙离子浓度为200 mg/L时,膜的渗透性最好,而过高的钙离子浓度并不利于降低膜污染。钙离子的投加强化了生物絮凝作用,可以降低SMP和LB-EPS的含量,主要通过降低外部阻力减缓膜污染;投加钙离子也可以增加絮体的大小,较大的絮体形成的泥饼有更好的过滤性,然而过高的钙离子浓度会使无机颗粒的量增加,造成平均粒径下降,将会加重内部污染,进而加剧膜污染。     

聚硅硫酸铁混凝去除石化废水二级出水中有机污染物的研究

采用聚硅硫酸铁(PFSiS)混凝剂对石化废水二级出水进行了强化混凝实验,考察其对有机污染物的去除效果,并对不同时期的絮体微观结构进行了研究。结果表明,PFSiS可有效去除水中COD,当PFSiS投加量为40 mg/L(以Fe计),静置时间为120 min,COD去除率可达50%左右;絮体的微观结构为空间网状结构,随静置时间的延长,絮体密实程度提高,颜色加深。     

A/O-MBR中MLSS浓度对污泥性能及膜通量的影响

采用国产聚丙烯中空纤维帘式膜组件,进行了A/O-MBR系统处理生活污水的实验研究,主要探讨了系统中污泥浓度(MLSS)与膜通量变化过程的关系。实验结果表明,MLSS由3 805 mg/L升高到6 912 mg/L时,污泥混合液胞外聚合物(EPS)由43 mg/g VSS增加到81 mg/g VSS,EPS中多糖与蛋白质的比例从0.87增加到1.08。同时,污泥相对疏水性(RH)的降低与Zeta电位的升高也在一定程度上共同促进了膜污染速率的上升。实验条件下,当运行时间为60 d左右,MLSS升高至6 200 mg/L时,跨膜压差上升迅速,膜组件清洗周期由初始的22 d缩短为11 d。A/O-MBR中由于MLSS浓度变化而导致的活性污泥混合液特性的变化,是影响膜通量变化的重要原因。     

The digestibility of waste activated sludges.

Laboratory digestion studies using waste activated sludges (WAS) were conducted to compare the digestion performance between anaerobic and aerobic processes. Nine samples of WAS from seven wastewater treatment plants were collected and batch-digested under both anaerobic and aerobic conditions for 30 days at 25 degrees C. The cation content of wastewater (both floc and solution phases) and solution biopolymer (protein and polysaccharide) was measured before and after digestion and compared with volatile solids destruction data. The study revealed that each digestion process was associated with a distinct biopolymer fraction, which accounted for differences in volatile solids reduction under anaerobic and aerobic conditions. The anaerobic digestion data showed strong correlations between soluble protein generation, ammonium production, percent volatile solids reduction, and floc iron (Fe). These data suggest that the amount of volatile solids destroyed by anaerobic digestion depends on the Fe content of floc. In aerobic digestion, polysaccharide accumulated in solution along with calcium and magnesium. For aerobic digestion, correlations between divalent cation release and the production of inorganic nitrogen were found. This implies that divalent cation-bound biopolymer, thought to be lectin-like protein, was the primary organic fraction degraded under aerobic conditions. The results of the study show that the cation content in wastewater is an important indicator of the material that will digest under anaerobic or aerobic conditions and that some of the volatile solids will digest only under either anaerobic or aerobic conditions.     

Effects of nitrogen and phosphorus limitation on the activated sludge biomass in a kraft mill biotreatment system.

Unlike wastewater, pulp and paper mill effluents are generally severely deficient in bioavailable nitrogen and phosphorus. The influence of nitrogen and phosphorus limitations on steady-state or typical pulp and paper mill activated sludge floc properties and performance was studied using a bioreactor-fed synthetic raw mill effluent and seeded with mill activated sludge. Limitation of either nitrogen or phosphorus decreased growth, five-day biochemical oxygen demand, and suspended solids removal. Nitrogen limitation greatly enhanced activated sludge floc poly-beta3-hydroxybutyrate (PHB), but not carbohydrate or extracellular polymeric substances (EPS). In contrast, phosphorus limitation increased total floc carbohydrate and EPS, but not PHB. The flocs showed little ability to store either nitrogen or phosphorus. Nitrogen limitation, but not phosphorus limitation, produced much more negative net floc surface charge, increasing fines, while phosphorus limitation, but not nitrogen limitation, increased the floc bound water content and surface hydrophobicity and decreased fines.     

Road dust emissions from paved roads measured using different mobile systems

Very few real-world measurements of road dust suspension have been performed to date. This study compares two different techniques (referred to as Sniffer and Emma) to measure road dust emissions. The main differences between the systems are the construction of the inlet, different instruments for recording particulate matter (PM) levels, and different loads on the wheel axes (the weight of Sniffer was much higher than that of Emma). Both systems showed substantial small-scale variations of emission levels along the road, likely depending on-road surface conditions. The variations observed correlated quite well, and the discrepancies are likely a result of variations in dust load on the road surface perpendicular to the driving direction that cause variations in the measurements depending on slightly different paths driven by the two vehicles. Both systems showed a substantial influence on the emission levels depending on the type of tire used. The summer tire showed much lower suspension than the winter tires (one nonstudded and one studded). However, the relative importance of the nonstudded versus studded tire was rather different. For the ratio of studded/nonstudded, Emma shows higher values on all road sections compared with Sniffer. Both techniques showed increased emission levels with increasing vehicle speed. When the speed increased from 50 to 80 km hr(-1), the relative concentrations increased by 30-170% depending on the tire type and dust load. However, for road sections that were very dirty, Sniffer showed a much higher relative increase in the emission level with the nonstudded tire. Sniffer's absolute concentrations were mostly higher than Emma's. Possible reasons for the differences are discussed in the paper. Both systems can be used for studying relative road dust emissions and for designing air quality management strategies.     

Environmental scanning electron microscopy (ESEM) as a new technique to determine the ice nucleation capability of individual atmospheric aerosol particles

Heterogeneous ice nucleation on synthetic silver iodide, natural kaolinite and montmorillonite particles via condensation, freezing and deposition modes was studied by environmental scanning electron microscopy (ESEM) in the temperature range of 250–270 K. By increasing the H₂O pressure in the sample chamber at constant temperature, ice formation can be studied in situ and can be related to the chemical composition of the particles that can be determined simultaneously. For silver iodide and kaolinite, supersaturation values of first ice formation are in good agreement (1–2% absolute) with diffusion chamber experiments. For both substances, threshold temperatures for the condensation, freezing and deposition modes are also in good agreement (within 2 K) with previous literature data. For montmorillonite, ESEM results for the supersaturation value of first ice formation and for threshold temperatures of condensation freezing and deposition mode lie within the large range reported in the literature.     

Comparison of sludge characteristics and PCR-DGGE based microbial diversity of nanofiltration and microfiltration membrane bioreactors

The objective of this study was to compare the sludge characteristics and microbial community diversity between the submerged nanofiltration membrane bioreactor (NF MBR) and microfiltration membrane bioreactor (MF MBR) treating the same municipal wastewater. The influence of a higher concentration of organic matter and salt was investigated. The results of water qualities showed that the dissolved organic carbon (DOC), total phosphorus (T-P) and salt concentrations of the supernatant in the NF MBR were three, four and two times as high as those in the MF MBR, respectively. The specific oxygen uptake rate of the NF MBR (2.9+/-0.4 mg O(2)g(-1)MLSSh(-1)) was lower than that of the MF MBR (4.3+/-1.1 mg O(2)g(-1)MLSS h(-1)). Result of extractable extracellular polymeric substances showed that the NF MBR sludge had more protein and less polysaccharide compared to the MF MBR sludge, whereas specific amount of total organic carbon were the same in both MBRs. The median floc diameters of the NF MBR and the MF MBR were 72+/-12 microm and 59+/-12 microm, respectively, which could be attributable to the different polysaccharide concentrations between both MBR mixed liquor. A higher concentration of materials (DOC, T-P and salt) in the bioreactor, determined by the high rejection rate of the NF membrane, did not significantly affect the microbial diversity under similar operation conditions.     

Ca(II)在活性污泥生物絮凝中的作用研究

采用4个平行的序批式反应器(SBR),研究了进水Ca²⁺浓度对活性污泥絮体表面特性和结构稳定性的影响,并由此来确定Ca²⁺在生物絮凝中的作用。结果表明：随着进水Ca²⁺浓度的增加,污泥中的Ca含量逐渐增大。进水中Ca²⁺的加入,增大了污泥絮体的粒径和密度,进而改善了污泥的沉降性能;Ca²⁺的加入,使可供结合的蛋白质数量最高增至近1倍,污泥表面疏水性也相应增强;污泥絮凝性能的改善,主要和可供Ca²⁺结合的蛋白质含量增加有关,而非多糖;EDTA通过络合污泥絮体中的Ca²⁺,破坏了由Ca²⁺架桥形成的污泥絮体结构,这说明Ca²⁺可通过和胞外聚合物（extracellular polymeric substances, EPS）中的负电官能团架桥来促进污泥絮体的形成并维持絮体结构的稳定性。     

Investigation of the role of biopolymer clusters in MBR membrane fouling using flash freezing and environmental scanning electron microscopy

The technique that employs flash freezing and environmental scanning electron microscopy (ESEM) was utilised for detailed investigation of the fouling materials in a membrane bioreactor (MBR). The method involves the flash freezing of a wet sample in liquid nitrogen for 10 s to preserve its structure for direct ESEM observation with a high image resolution. ESEM images show that the sludge cake formed by simple filtration of the MBR bulk sludge has a highly porous, sponge-like structure with a fairly low resistance. However, the fouling layer attached to the membrane surface contains a thin gel layer under the main body of the sponge-like sludge cake, which is similar to that formed by filtration of a dispersion of biopolymer clusters (BPCs). It is apparent that BPCs tend to accumulate on the membrane surface, and the gel layer is largely responsible for the high filtration resistance of the cake layer on the fouled membranes.     

Ca(Ⅱ)在活性污泥生物絮凝中的作用研究

采用4个平行的序批式反应器(SBR),研究了进水Ca2+浓度对活性污泥絮体表而特性和结构稳定性的影响,并由此来确定Ca2+在生物絮凝中的作用.结果表明:随着进水Ca2+浓度的增加,污泥中的Ca含量逐渐增大.进水中Ca2+的加入,增大了污泥絮体的粒径和密度,进南改善了污泥的沉降性能;Ca2+的加入,使可供结合的蛋白质数量最高增至近1倍,污泥表面疏水性也相应增强;污泥絮凝性能的改善,主要和可供Ca2+结合的蛋白质含量增加有关,而非多糖;EDTA通过络合污泥絮体中的Ca2+,破坏了山Ca2+架桥形成的污泥絮体结构,这说明Ca2+可通过和胞外聚合物(extracellular polymeric substances,EPS)中的负电官能团架桥来促进污泥絮体的形成并维持絮体结构的稳定性.