Analysis of chlorothalonil and degradation products in soil and water by GC/MS and LC/MS

We present a method using gas chromatography (GC) and liquid chromatography (LC) coupled to a mass selective detector to measure concentrations of the fungicide chlorothalonil and several of its metabolites in soil and water. The methods employed solid-phase extraction using a hydrophobic polymeric phase for the isolation of analytes. In lake water, average analyte recoveries ranged from 70% to 110%, with exception of pentachloronitrobenzene that gave low recoveries (23%). The method detection limits were determined to be in the range of 1 and 0.1microg l(-1) for the LC and GC methods, respectively. In soil samples, recoveries ranged from 80% to 95% for 4-hydroxy-2,5,6-trichloroisophthalonitrile (metabolite II) and 1,3-dicarbamoyl-2,4,5,6-tetrachlorobenzene (metabolite III). Limits of detection (LOD) were 0.05 and 0.02microg g(-1), respectively. Chlorothalonil and other metabolites were analyzed by GC giving recoveries ranging from 54% to 130% with LOD of 0.001-0.005microg g(-1).     

Validation of three new methods for determination of metal emissions using a modified Environmental Protection Agency Method 301

Three new methods applicable to the determination of hazardous metal concentrations in stationary source emissions were developed and evaluated for use in U.S. Environmental Protection Agency (EPA) compliance applications. Two of the three independent methods, a continuous emissions monitor-based method (Xact) and an X-ray-based filter method (XFM), are used to measure metal emissions. The third method involves a quantitative aerosol generator (QAG), which produces a reference aerosol used to evaluate the measurement methods. A modification of EPA Method 301 was used to validate the three methods for As, Cd, Cr, Pb, and Hg, representing three hazardous waste combustor Maximum Achievable Control Technology (MACT) metal categories (low volatile, semivolatile, and volatile). The modified procedure tested the methods using more stringent criteria than EPA Method 301; these criteria included accuracy, precision, and linearity. The aerosol generation method was evaluated in the laboratory by comparing actual with theoretical aerosol concentrations. The measurement methods were evaluated at a hazardous waste combustor (HWC) by comparing measured with reference aerosol concentrations. The QAG, Xact, and XFM met the modified Method 301 validation criteria. All three of the methods demonstrated precisions and accuracies on the order of 5%. In addition, correlation coefficients for each method were on the order of 0.99, confirming the methods' linear response and high precision over a wide range of concentrations. The measurement methods should be applicable to emissions from a wide range of sources, and the reference aerosol generator should be applicable to additional analytes. EPA recently approved an alternative monitoring petition for an HWC at Eli Lilly's Tippecanoe site in Lafayette, IN, in which the Xact is used for demonstrating compliance with the HWC MACT metal emissions (low volatile, semivolatile, and volatile). The QAG reference aerosol generator was approved as a method for providing a quantitative reference aerosol, which is required for certification and continuing quality assurance of the Xact.     

The environmental fate of the primary degradation products of alkylphenol ethoxylate surfactants in recycled paper sludge.

Alkylphenol ethoxylates (APEOs) are a group of non-ionic surfactants that are degraded microbially into more lipophilic degradation products with estrogenic potential, including nonylphenol monoethoxylate (NP1EO), nonylphenol diethoxylate (NP2EO), octylphenol (4-tOP) and nonylphenol (4-NP). Nonylphenol ethoxylates are used in paper recycling plants for de-inking paper and have the potential to be released into the environment through spreading of wastewater treatment sludge for soil amendment. Three samples of recycled paper sludge were collected from farmers' fields and analyzed for concentrations of NP1EO, NP2EO, 4-NP and 4-tOP. Each sample differed in the amount of time elapsed since the sludge was placed on farmers' fields. Primary degradation products of APEOs were present at low micrograms/g concentrations in the sludge samples. Differences in the concentrations of these analytes in sludge samples indicated that APEO concentrations declined by 84% over a period of 14 weeks on farmers' fields. Changes in the chromatographic patterns of acetylated 4-NP indicated that there is a group of recalcitrant nonylphenol isomers that degrades more slowly than other isomers. These data indicate that microbial degradation may reduce the risk of environmental contamination by these compounds, but more work is required to assess the toxic potential of APEOs in sludges used for soil amendment.     

Characterization of organic compounds in aerosol particles from a coniferous forest by GC-MS

Atmospheric aerosol particles were collected in a Finnish Scots pine forest as part of a European Union project. Sampling was done in March-April 2003 with a high-volume sampler. Dynamic ultrasonic-assisted solvent extraction and gas chromatography-mass spectrometry (GC-MS) were applied to the analysis of aerosol samples for analytes such as n-alkanes, polycyclic aromatic hydrocarbons (PAH), oxidized polycyclic aromatic hydrocarbons (oxy-PAHs), sesquiterpenes (SQT) and oxidized sesquiterpenes (oxy-SQT). The highest concentrations were found for the n-alkanes, which were present in a wide range (C11-C32) indicating both biogenic and anthropogenic sources. PAH compounds were found in every sample while oxy-PAH compounds were present in low concentrations in a few samples. A few oxidized monoterpenes, most notably (-)-verbenone and pinonaldehyde, were found in several samples in concentrations clearly exceeding the PAH concentrations. The effect of temperature could be seen in most samples, where the concentrations of n-alkanes declined with decreasing temperatures. Particle formation events were accompanied by higher concentrations of heavy n-alkanes, verbenone and pinonaldehyde.     

Determination of sixteen pesticides in peppers using high-performance liquid chromatography/mass spectrometry

A method for the detection and quantification of 16 pesticides: flufenoxuron, fenoxycarb, dimethomorph, acetamiprid, imidacloprid, lufenuron, thiacloprid, thiabendazole, thiophanate-methyl, spinosad, fenbutatin oxide, methoxyfenozide, oxamyl, clothianidin, thiamethoxam and carbendazim has been developed based on high-performance liquid chromatography-mass spectrometry. Pesticide residues were extracted from the samples according to the QuEChERS method which stands for quick, essay, cheap, effective, rugged and safe. Homogenised analytical portions (10 g ± 0.1) of samples of peppers were spiked at two levels (10 and 100 μg kg?1) with a small volume of an appropriate standard mixture solution containing each pesticide. Analyses were performed using electrospray ionization (ESI) and a MSD trap system. Chromatography separation was achieved using a ZORBAX SB-C18 3.5 μm particle size analytical column, 2.1 × 50 mm from Agilent, with gradient elution at a flow-rate of 0.4 mL/min with mobile phases: waters-0.1 % HCOOH-5 mM HCOONH? and MeOH-5 mM HCOONH?. The method has been validated based on the SANCO European Guidelines. Under the optimized conditions the recoveries (n = 7) were in the range 70-110 % with satisfactory precision (CV ≤ 20 %). A linear dynamic range was obtained over a range of concentrations from 10 to 100 μg kg?1 for each of the analytes, with correlation coefficients >0.997.     

Occurrence and temporal variations of the xenoestrogens bisphenol A, 4-<Emphasis Type="Italic">tert</Emphasis>-octylphenol,and tech. 4-nonylphenol in two German wastewater treatment plants

GOAL, SCOPE, AND BACKGROUND: The xenoestrogens bisphenol A, 4-tert-octylphenol, and the technical isomer mixture of 4-nonylphenol (tech. 4-nonylphenol) belong to the group of chemicals which are called endocrine disrupters due to their property of causing hormonal dysfunctions in the endocrine system of organisms at very low concentrations. Bisphenol A, 4-tert-octylphenol, and the tech. 4-nonylphenol (mixture of isomers) were determined in water samples collected from the influent and effluent of two German wastewater treatment plants (WWTP) during a long-time sampling period from February 2003 till August 2005 to assess their occurrence and temporal variations in WWTPs. METHODS: The compounds were extracted and concentrated from water by solid-phase extraction (SPE) using Bond Elut PPL cartridges and quantified by use of gas chromatography-mass spectrometry (GC-MS). RESULTS: The influent concentrations were as follows: Bisphenol A < limit of detection of the method (< ldm)--12,205 ng L(-1), tech. 4-nonylphenol < ldm--10,186 ng L(-1), and 4-tert-octylphenol 39-1,495 ng L(-1). The measured effluent concentrations were lower with values in the range of < ldm--7,625 ng L(-1) for bisphenol A, < ldm--14,444 ng L(-1) for tech. 4-nonylphenol, and < ldm--392 ng L(-1) for 4-tert-octylphenol. All target compounds were largely eliminated during the wastewater treatment process. The elimination efficiency varied between 73% and 93%. DISCUSSION: All analytes show highly fluctuating influent concentrations with very high peak concentrations at particular sampling times. The variation of effluent concentrations is by far lower than the variation of influent concentrations. For tech. 4-nonylphenol, a significant temporal concentration variation has been detected with very high concentrations up to the microgram-per-liter level in the time from February 2003 till July 2003 and clearly decreasing concentrations in the time from June 2004 till August 2005. This corresponds well with the implementation of Directive 2003/53/EC (nonylphenol and nonylphenol ethoxylates in the European Union "may not be placed on the marked or used as a substance or constituent of preparations in concentrations equal or higher than 0.1% by mass") from January 2005 on. Bisphenol A is present in the effluent samples in a wide range of concentrations from below the detection limit to high concentrations up to the microgram-per-liter level. For 4-tert-octylphenol, no particular trend of concentration development has been observed. CONCLUSIONS: Combined SPE and GC-MS proved to be an efficient method to identify and quantify polar organic compounds in environmental samples. With respect to the concentrations measured in the present study, bisphenol A sometimes is the prominent compound in influent samples. Neither bisphenol A nor 4-tert-octylphenol or tech. 4-nonylphenol show seasonal variations. However, there was a significant general trend of decreasing concentrations of tech. 4-nonylphenol in influent and effluent samples from both WWTPs which probably reflects the implementing Directive 2003/53/EC. RECOMMENDATIONS AND PERSPECTIVES: Further research is needed to investigate whether the observed decrease of tech. 4-nonylphenol concentrations in German WWTPs since June 2004 will continue further on. The reason for the high effluent concentrations of bisphenol A in only a few samples has to be clarified in further research. The results from this study provide insight into the concentration development of the xenoestrogens bisphenol A, tech. 4-nonylphenol, and 4-tert-octylphenol in WWTPs in the time span between 2003 and 2005.     

Effects of acid-washing filter treatment on quantification of aerosol organic compounds

The tests of standard mixtures and four sets of atmospheric particulate samples showed that an acid-wash (AW) pretreatment of fluorocarbon-coated glass fiber filters prior to aerosol sampling enhanced the quantifiable organic compounds for more than 29% (or 66 ng m⁻³); in particular, 47–273 ng m⁻³ (21–366%) more water-soluble organic compounds (WSOCs) were measured. When the acid-pretreated filters were employed, up to nine more organic species were measured in the individual daily samples. Because the acid pretreatment reduced the metal contaminants in the glass fiber filters, using the AW filters for aerosol sampling allows higher extraction recoveries of organic compounds. Since the fingerprinting compounds were more accurately determined when the aerosol samples were collected on the AW filters, better assessment of emission sources and toxicity of air pollutants can be obtained.     

Simultaneous determination of eight metabolites of organophosphate and pyrethroid pesticides in urine

A simultaneous method for quantifying eight metabolites of organophosphate pesticides and pyrethroid pesticides in urine samples has been established. The analytes were extracted using liquid–liquid extraction coupled with WCX solid phase extraction (SPE) cartridges. Eight metabolites were chemically derivatized before analysis using gas chromatography–tandem mass spectrometry (GC–MS–MS). The separation was performed on a HP-5MS capillary column (30 m × 0.25 mm × 0.25 µm) with temperature programming. The detection was performed under electro-spray ionization (ESI) in multiple reaction monitoring (MRM) mode. An internal standard method was used. The extraction solvent, types of SPE cartridges and eluents were optimized by comparing the sample recoveries under different conditions. The results showed that the calibration curves of the five organophosphorus pesticides metabolites were linear in the range of 0.2–200 μg/L (r² ≥ 0.992) and that of the three pyrethroid pesticides metabolites were linear in the range of 0.025–250 μg/L (r² ≥ 0.991). The limits of detection (LODs, S/N ≥ 3) and the limits of quantification (LOQs, S/N ≥ 10) of the eight metabolites were 0.008–0.833 μg/L and 0.25–2.5 μg/L, respectively. The recoveries of the eight metabolites ranged from 54.08% to 82.49%. This efficient, stable, and cost-effective method is adequate to handle the large number of samples required for surveying the exposure level of organophosphorus and pyrethroid pesticides in the general population.     

Polycyclic aromatic hydrocarbons (PAHs) in the aerosol in Beijing, China, measured by aminopropylsilane chemically-bonded stationary-phase column chromatography and HPLC/fluorescence detection

We developed a useful analytical method for the determination of polycyclic aromatic hydrocarbons (PAH) concentrations in the aerosol of China. We used an accelerated solvent extraction (ASE) method for the extraction of PAHs from the aerosol samples, in order to reduce the extraction time and the solvent volume used. The optimum purification method was developed, with aminopropylsilane chemically-bonded stationary-phase column chromatography, in order to remove many co-extractives which cannot be removed by conventional purification methods using silica-gel column chromatography. HPLC/fluorescence detection (FLD) was adopted as the analytical method, because it has very high sensitivity to PAH and it is easy to install, operate, and maintain as compared with GC/MS. With the analytical method developed in this study, the recovery and precision (RSD) for most of the PAHs ranged from 75% to 129% and from 2.8% to 22.7%, respectively. The concentrations of PAHs in the aerosol samples collected from October 2003 to April 2005 in Beijing, China were determined using the newly developed method. SigmaPAHs, which is the sum of the concentrations of all detected PAHs, was 177.8 +/- 239.9 ng m(-3) (n = 64). The SigmaPAHs concentration in the heating season (305.1 +/- 279.0 ng m(-3), n = 33) was 7.2 times higher than that in the non-heating season (42.3 +/- 32.0 ng m(-3), n = 31). These strong seasonal variations in atmospheric PAH concentration are possibly due to coal combustion for residential heating in winter.     

Sorbent-assisted liquid-liquid extraction (Chem-Elut) of polychlorinated biphenyls, dibenzo-p-dioxins and dibenzofurans in the lipid fraction of human blood plasma

This work compares two lipid extraction methods for determining 24 polychlorinated biphenyls (PCBs), seven dibenzo-p-dioxins (PCDDs) and ten dibenzofurans (PCDFs) in human blood plasma. The first method was based on conventional liquid-liquid partitioning with chloroform-methanol and the other made use of a sorbent (Chem-Elut) to facilitate the partitioning of lipids into a mixture of hexane and 2-propanol. A multi-layer-silica column including acid- and base-impregnated silica gel was used to reduce the amounts of lipid present in the samples before a basic alumina clean-up step and activated carbon fractionation of planar analytes (PCDD/Fs and non-ortho-PCBs) and non-planar analytes (including ortho-chlorinated PCBs). Gas chromatography coupled to high resolution mass spectrometry was used to identify and quantify the analytes in the two fractions. The wet weight based concentrations obtained by the two methods were in agreement but both methods suffer from large organic solvent consumption. The toxic equivalencies derived for PCBs and PCDD/Fs using the two methods were also in agreement. However, the chloroform-methanol method gave slightly higher lipid recoveries, although with greater variation, than the sorbent-assisted method. Nevertheless, despite giving lower lipid recoveries, the sorbent-assisted method has advantages in ease of use and applicability to whole blood samples. The formation of emulsions was avoided with the Chem-Elut method, which probably explains the lower variability in the lipid determinations.     

Validation of Three New Methods for Determination of Metal Emissions Using a Modified Environmental Protection Agency Method 301

Abstract

Three new methods applicable to the determination of hazardous metal concentrations in stationary source emissions were developed and evaluated for use in U.S. Environmental Protection Agency (EPA) compliance applications. Two of the three independent methods, a continuous emissions monitor-based method (Xact) and an X-ray-based filter method (XFM), are used to measure metal emissions. The third method involves a quantitative aerosol generator (QAG), which produces a reference aerosol used to evaluate the measurement methods. A modification of EPA Method 301 was used to validate the three methods for As, Cd, Cr, Pb, and Hg, representing three hazardous waste combustor Maximum Achievable Control Technology (MACT) metal categories (low volatile, semivolatile, and volatile). The modified procedure tested the methods using more stringent criteria than EPA Method 301; these criteria included accuracy, precision, and linearity. The aerosol generation method was evaluated in the laboratory by comparing actual with theoretical aerosol concentrations. The measurement methods were evaluated at a hazardous waste combustor (HWC) by comparing measured with reference aerosol concentrations. The QAG, Xact, and XFM met the modified Method 301 validation criteria. All three of the methods demonstrated precisions and accuracies on the order of 5%. In addition, correlation coefficients for each method were on the order of 0.99, confirming the methods’ linear response and high precision over a wide range of concentrations. The measurement methods should be applicable to emissions from a wide range of sources, and the reference aerosol generator should be applicable to additional analytes. EPA recently approved an alternative monitoring petition for an HWC at Eli Lilly’s Tippecanoe site in Lafayette, IN, in which the Xact is used for demonstrating compliance with the HWC MACT metal emissions (low volatile, semivolatile, and volatile). The QAG reference aerosol generator was approved as a method for providing a quantitative reference aerosol, which is required for certification and continuing quality assurance of the Xact.     

Simultaneous determination of chlorothalonil and its metabolite 4-hydroxychlorothalonil in greenhouse air: dissipation process of chlorothalonil

An analytical method was developed and tested for the simultaneous determination of chlorothalonil and its main metabolite 4-hydroxychlorothalonil, in airborne samples. High performance liquid chromatography equipped with Ultra-violet detector was used to separate and quantify the analytes. Glass microfibre filters for the collection of the analytes' particles were tested. Solid sorbents, such as Tenax, Florisil, XAD-2 and silica gel, were studied to find out the most suitable material for the collection of the analytes in the gas phase. The results have shown that only chlorothalonil was trapped in the vapor phase with highest results obtained when silica gel was the sorbent of choice. Linearity was demonstrated in a wide concentration range 0.01-10.00 mg L(-1). Recoveries from spiked glass microfibre filters and silica gel cartridges for chlorothalonil and 4-hydroxychlorothalonil were almost quantitative. The quantification limits were calculated to be 8.4 and 19.6 ng m(-3) in air for chlorothalonil and 4-hydroxychlorothalonil, respectively. The two analytes spiked on the GF/A filters and silica gel cartridges were proven to be stable for more than 15 days, at 4degrees C and ambient temperature. The applicability of the present method was demonstrated by the analysis of the chlorothalonil and its metabolite in greenhouse air.     

Water-soluble organic nitrogen in atmospheric aerosol: a comparison of UV and persulfate oxidation methods

Two well established methods that are widely applied in the determination of marine dissolved organic nitrogen (DON) have been investigated in their application to the determination of rainwater DON and the water-soluble organic nitrogen component of atmospheric aerosol. Empirical observation highlighted some difficulties in the analysis of DON in these non-marine matrices, so some practical suggestions for the extension of the oxidative methods to atmospheric samples are proposed.Ten rain samples, 20 aqueous aerosol extracts, and a suite of commercially obtained organic nitrogen compounds were both chemically oxidised by persulfate and oxidised by exposure to high-intensity ultraviolet light. The total dissolved nitrogen concentration of the rains in this study ranged from 4 to 35 μM nitrogen. The aerosol extracts were diluted to a pre-oxidation concentration range of 12–65 μM N for oxidation and analysis. Both UV and persulfate methods require the aqueous extract of the aerosol organic nitrogen to be diluted approximately to rainwater concentrations for optimal oxidation efficiency, since sub-optimal recoveries and high analytical variability arise at high concentration. Some potential causes of analytical interference at higher concentration are discussed.This study shows that total dissolved nitrogen results obtained by the two methods are linearly correlated (with an R² of 0.87 for 30 samples) over the full range of natural rainwater concentrations, but results obtained using the persulfate oxidation are about 30% lower than those obtained by photo-oxidation.     

Immunoassay of red dyes based on the monoclonal antibody of β-naphthol

The objective of the present study was to develop a multi-analyte immunoassay for the determination of eight red dyes in food samples. Two dye intermediates (2-hydroxy-1-naphthoic acid and 1-amino-2-naphthol) were used as the haptens to produce the monoclonal antibodies. The obtained monoclonal antibodies recognized Sudan 1–4, Para red, Sudan red G, Sudan red B and Acid orange II simultaneously. After evaluation of different antibody/coating antigen combinations, a heterologous indirect competitive enzyme linked immunosorbent assay was developed to determine the eight red dyes in food samples (chili oil, chili powder, tomato sauce, hotpot seasoning). The crossreactivities to the eight analytes were in the range of 61%–79% (with β-naphthol as 100%), and the limits of detection were in the range of 1.3–1.9 ng/mL. The recoveries of the eight analytes from the fortified blank samples were in the range of 84.2%–115% with coefficients of variation lower than 18.3%. Therefore, this method could be used as a rapid and simple tool to detect the residues of the eight red dyes in foods.     

Determination of chloramphenicol, enrofloxacin and 29 pesticides residues in bovine milk by liquid chromatography-tandem mass spectrometry

A sensitive method for determination of chloramphenicol, enrofloxacin and 29 pesticides residues in bovine milk by high-performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) was developed. Residues of the targets were extracted from milk with acetonitrile, cleaned up by C₁₈-SPE cartridge, and then determined by HPLC-MS/MS. The MS detection was operated in positive or negative ionization mode, depending on the compounds. For confirmation of each target compound, two precursor ion > product ion transitions were selected by multi-reaction monitoring mode (MRM). The method showed good linearity for all the tested compounds over the studied concentration range with correlation coefficient higher than 0.9910. Recoveries for the studied compounds at three spiked levels (0.05, 0.10, 0.19 mg kg⁻¹) in bovine milk were in the range of 71-107% with RSDs not larger than 13.7%, except that recoveries of trifluralin ranged between 62% and 70% at the spiked levels. Limits of quantitation for the analytes were estimated to range between 0.03 × 10⁻³ and 14.5 × 10⁻³ mg kg⁻¹. The proposed method was applied for the determination of the analytes residues in real samples. The found levels of the analytes in milk samples were lower than maximum residues levels (MRL).     

Application of ultrasonic assisted extraction of chemically diverse organic compounds from soils and sediments

The objective of this research was the development, optimization, and demonstration of an ultrasonic assisted extraction (UAE) based method for organic anthropogenic waste indicators (AWIs) with a range of physicochemical properties from soil and sediment samples. The optimized method was designed to be cost effective compared to existing extraction methods, which may require large quantities of consumables, produce substantial volumes of organic waste, or require costly instrumentation or equipment. Reagent grade sand, soil collected from the native grassland in proximity to Eastern Washington University (EWU), and sediment samples collected from the Spokane river were used as sample matrices during method development. These matrices were fortified with eight AWIs of varying chemical properties that are representative of a variety of household, industrial, and agricultural sources. The recoveries of the AWIs spiked onto these matrices were determined in the extracts using gas chromatography/mass spectrometry (GC/MS). These values reflect the efficiency of the method for extraction of these analytes from representative environmental matrices. Recoveries ranged from 46.1% to 110% in the fortified soil and from 49.2% to 118.6% in the fortified sediment samples, which is comparable with existing methods for the study analytes. The optimized method was then used to quantify AWIs in a biosolid-amended soil. Indole and p-cresol were detected in the biosolid-amended soil.     

Analysis of polycyclic aromatic hydrocarbons in wastewater treatment plant effluents using hollow fibre liquid-phase microextraction

A simple and efficient method for the enrichment of low molecular weight polycyclic aromatic hydrocarbons (PAHs) in effluents originating from wastewater treatment plants is presented here. The proposed protocol couples the recently introduced hollow fibre liquid-phase microextraction (LPME) method with gas chromatography-mass spectrometry. Method parameters were controlled and the optimised experimental conditions were: 5 ml aqueous samples, containing 2.5% NaCl w/v, stirred at 1000 rpm, extracted with toluene for 15 min. The developed protocol yielded a linear calibration curve in the concentration range from 0.5 to 50 microg l(-1) for all target analytes (namely acenaphthene, phenanthrene, fluoranthene and pyrene) and limits of detection in the low microg l(-1) level (0.005-0.011 microg l(-1)). The repeatability and inter-day precision of the method varied between 2.7% and 11.3% and 7.9% and 14.4% respectively. The relative recoveries from different types of natural water samples revealed that matrix had a small effect on the hollow fibre LPME process. The developed method was then applied for the determination of PAHs contamination in effluent samples taken from two major municipal wastewater treatment plants. The results were compared with those obtained with solid-phase microextraction. The ability of both microextraction methods to concentrate organic analytes was demonstrated as both methods confirmed the presence of PAHs as well as of phthalates in the examined effluent samples.     

Simultaneous gas chromatographic determination of chlorpyrifos and its impurity sulfotep in liquid pesticide formulations

An analytical method for simultaneous determination of the active substance (chlorpyrifos) and its relevant impurity (sulfotep) in commercial pesticide formulations has been developed and validated. The proposed method entails extraction of the analytes from samples by sonication with acetone and analysis by gas chromatography-flame ionization detection (GC-FID). The proposed method was characterized by satisfactory accuracy and precision. The repeatability expressed as relative standard deviation (RSD) was lower than the acceptable values calculated from the modified Horwitz equation whereas individual recoveries were in the range of 98–102% and 80–120% for chlorpyrifos and sulfotep, respectively. The limit of quantification (LOQ) for the impurity (sulfotep) was 0.003 mg mL^?1 corresponding to the maximum permitted level according to Food and Agricultural Organization of the United Nations (FAO) specifications for the active substance (chlorpyrifos) being 3 g kg^?1 of the chlorpyrifos content found. The main advantage of the proposed method was a considerable reduction in the analysis time since both analytes were determined based on a single injection into the GC-FID. Analysis of real samples of commercial pesticide formulations confirmed fitness-for-purpose of the proposed method.     

Determination of pesticides of different chemical classes in drinking water of the state of Santa Catarina (Brazil) using solid-phase microextraction coupled to chromatographic determinations

The evaluation of the concentration of pesticides in drinking water presents a real concern. In this study, a simple and rapid method based on solid-phase microextraction (SPME) followed by gas chromatography–mass spectrometry and electron capture detectors was developed aiming at multiclass determination of 23 pesticides regulated by the Brazilian legislation. The extraction was carried out by direct immersion mode (DI-SPME) using DVB/Car/PDMS fiber coating. In order to improve the extraction efficiency, parameters such as temperature, salting-out effect, and extraction time were optimized. The method was evaluated using drinking water samples spiked with the analytes at different concentrations, and it showed good linearity in the range studied. The values obtained for limits of quantification (LOQ) were below the limits established by Brazilian regulations. Accuracy and precision of the method exhibited satisfactory results, providing relative recoveries from 70 to 123.34% at three spiked levels, and the relative standard deviations ranged from 0.53 to 24.8%. The method was applied in 20 drinking water samples from 13 cities in the State of Santa Catarina, Brazil.

     

Size distribution of black (BC) and total carbon (TC) in Vienna and Ljubljana

During two campaigns in winter 2004, size segregated impactor samples (0.1-10 microm) and filter samples were taken in two Central European cities (Vienna, Austria and Ljubljana, Slovenia). The impactor samples were analyzed for major inorganic ions and short-chain organic acids, total carbon (TC) and black carbon (BC). Maximum concentrations of total mass were 71.6 microg m(-3) in Vienna and 73.1 microg m(-3) in Ljubljana. Minimum concentrations in Vienna were only half those in Ljubljana. The BC content of the aerosol was similar (ca. 8%), but the BC/TC ratio was higher in Vienna than in Ljubljana (0.39 vs. 0.29), reflecting the different contribution of diesel traffic emissions. The mass median diameters of the submicron size distributions of all major fractions (total mass, TC, BC and SO(4)(2-)) were smaller in Vienna (0.43 microm, 0.41 microm, 0.38 microm and 0.48 microm, respectively) than in Ljubljana (0.55 microm, 0.44 microm, 0.42 microm and 0.60 microm, respectively). Impactor/filter ratios for total mass were 0.79 in Vienna and 0.82 in Ljubljana, while the ratios for BC were 0.56 in Vienna and 0.49 in Ljubljana. An estimation of the mixing state of accumulation mode BC indicated that 33% and 37% of BC, respectively, are mixed externally to the aerosol in the accumulation size range in Vienna and Ljubljana.