选矿废水的回用处理研究与实践

铅锌矿泡沫浮选废水含有大量Pb2 + 离子和有机硫化物 ,经过混凝沉淀和活性炭吸附 ,去除其中的悬浮物、重金属离子和部分COD、降低其起泡性 ,然后回用生产。回用实践证明 ,选矿废水经过上述工艺处理后 ,其浮选选别指标与洁净水基本一致     

Heavy metal removal from synthetic wastewaters in an anaerobic bioreactor using stillage from ethanol distilleries as a carbon source

This work was conducted to investigate the possibility of using stillage from ethanol distilleries as substrate for sulfate reducing bacteria (SRB) growth and to evaluate the removal efficiency of heavy metals present in wastewaters containing sulfates. The experiments were carried out in a continuous bench-scale Upflow Anaerobic Sludge Blanket reactor (13 l) operated with a hydraulic retention time of 18 h. The bioreactor was inoculated with 7 l of anaerobic sludge. Afterwards, an enrichment procedure to increase SRB numbers was started. After this, cadmium and zinc were added to the synthetic wastewater, and their removal as metal sulfide was evaluated. The synthetic wastewater used represented the drainage from a dam of a metallurgical industry to which a carbon source (stillage) was added. The results showed that high percentages of removal (>99%) of Cd and Zn were attained in the bioreactor, and that the removal as sulfide precipitates was not the only form of metal removal occurring in the bioreactor environment.     

Heavy metal removal from synthetic wastewaters in an anaerobic bioreactor using stillage from ethanol distilleries as a carbon source

This work was conducted to investigate the possibility of using stillage from ethanol distilleries as substrate for sulfate reducing bacteria (SRB) growth and to evaluate the removal efficiency of heavy metals present in wastewaters containing sulfates. The experiments were carried out in a continuous bench-scale Upflow Anaerobic Sludge Blanket reactor (13 l) operated with a hydraulic retention time of 18 h. The bioreactor was inoculated with 7 l of anaerobic sludge. Afterwards, an enrichment procedure to increase SRB numbers was started. After this, cadmium and zinc were added to the synthetic wastewater, and their removal as metal sulfide was evaluated. The synthetic wastewater used represented the drainage from a dam of a metallurgical industry to which a carbon source (stillage) was added. The results showed that high percentages of removal (>99%) of Cd and Zn were attained in the bioreactor, and that the removal as sulfide precipitates was not the only form of metal removal occurring in the bioreactor environment.     

Removal of insoluble heavy metal sulfides from water

The necessity of heavy metal removal from wastewater has led to increasing interest in absorbents. We have developed a new approach to obtain high metal adsorption capacity by precipitating metal sulfides with sodium sulfide on the surface of bentonite and adhere them to the absorbent. This method allowed to remove approximately 90% of cadmium as CdS from 10(-4)-10(-6) M CdCl2 solutions. Additional reactions are related to the removal of excess sodium sulfide by the release of hydrogen sulfide and oxidation to sulfur using carbogen gas (5% CO2, 95% O2) followed by aeration.     

Effect of sulfate reduction activity on biological treatment of hexavalent chromium [Cr(VI)] contaminated electroplating wastewater under sulfate-rich condition

Electroplating wastewater (EW) containing heavy metals was treated by a two-stage packed-bed reactor system. The EW was highly contaminated with hexavalent chromium and other heavy metals as well as sulfate because sulfuric acid had been mainly used to polish the surface of metals to be electroplated. This acidic EW was effectively neutralized in an alkaline reactor where limestone had been packed. The neutralized wastewater together with organic wastewater from a starch-processing factory (SPW) was fed to a bioreactor packed with waste biomass. The SPW was used to supplement the electron donor in the sulfidogenic bioreactor. During the whole operation, we investigated the stoichiometry of electron to see what could be a major factor to remove Cr in the wastewater. The removal rates of sulfate and Cr(VI) were dependent on the consumption rate of organic materials in the wastewater. The stoichiometric studies also showed that about 63% of electrons from oxidation of organic materials were used to reduce sulfate. When the electrons of sulfide oxidation to elemental sulfur was at least 1.3 times higher than that of Cr(VI) reduction to Cr(III), Cr(VI) was completely removed. This result suggests that Cr(VI) reduction can be expected to take place under sulfate-rich anaerobic conditions, and sulfide produced by sulfate reducing bacteria could be used to immobilize soluble chromium through Cr(VI) reduction.     

硫化镍异相结晶法处理含镍废水

针对含络合剂的重金属废水,以含镍废水为例,探索了以气体硫化氢为结晶药剂的硫化镍异相结晶技术。废水以薄层液膜方式铺展于结晶载体表面,硫化氢气体穿过气液界面进入液相,硫离子与金属离子在载体表面异相结晶析出,重金属得以去除。以含酒石酸的模拟化学镀镍废水为对象,静态实验与动态实验均表明该技术具有可行性,硫化镍沉淀在结晶载体表面异相结晶析出,且附着稳定;络合剂对反应影响小;进水流速为4 mL/min,硫化钠流速为0.65 g/min,氮气流速为0.16 L/min时,出水镍浓度为49～53 mg/L,单位面积滤布表面结晶平均去除镍量为0.98 g/(m2.h)。     

Multi-component adsorption of copper,nickel and zinc from aqueous solutions onto activated carbon prepared from date stones

The removal of Cu²⁺, Ni²⁺, and Zn²⁺ ions from their multi-component aqueous mixture by sorption on activated carbon prepared from date stones was investigated. In the batch tests, experimental parameters were studied, including solution pH, contact time, initial metal ions concentration, and temperature. Adsorption efficiency of the heavy metals was pH-dependent and the maximum adsorption was found to occur at around 5.5 for Cu, Zn, and Ni. The maximum sorption capacities calculated by applying the Langmuir isotherm were 18.68 mg/g for Cu, 16.12 mg/g for Ni, and 12.19 mg/g for Zn. The competitive adsorption studies showed that the adsorption affinity order of the three heavy metals was Cu²⁺?>?Ni²⁺?>?Zn²⁺. The test results using real wastewater indicated that the prepared activated carbon could be used as a cheap adsorbent for the removal of heavy metals in aqueous solutions.     

Occurrence and fate of heavy metals in the wastewater treatment process

The occurrence and the fate of heavy metals (Cd, Pb, Mn, Cu, Zn, Fe and Ni) during the wastewater treatment process were investigated in the wastewater treatment plant (WTP) of the city of Thessaloniki, northern Greece, operating in the activated sludge mode. For this purpose, wastewater and sludge samples were collected from six different points of the plant, namely, the influent (raw wastewater, RW), the effluent of the primary sedimentation tank (primary sedimentation effluent, PSE), the effluent of the secondary sedimentation tank (secondary sedimentation effluent, SSE), sludge from the primary sedimentation tank (primary sludge, PS), activated sludge from the recirculation stream (activated sludge, AS), and the digested/dewatered sludge (final sludge, FS).

The distribution of metals between the aqueous and the solid phase of wastewater was investigated. Good exponential correlation was found between the metal partition coefficient, logK_p, and the suspended solids concentration. The mass balance of heavy metals in the primary, secondary and the whole treatment process showed good closures for all metal species. The relative distribution of individual heavy metals in the treated effluent and the sludge streams indicated that Mn and Cu are primarily (>70%) accumulated in the sludge, while 47–63% of Cd, Cr, Pb, Fe, Ni and Zn remain in the treated effluent.     

臭氧生物活性炭工艺处理某多金属硫化矿浮选废水的小试研究

某多金属硫化矿选矿厂浮选废水水量大,目前该厂对浮选废水的处理方法为尾矿库砂滤治理,但该方法存在效率低、周期长、回用影响选矿指标等众多弊端。为高效低成本的处理浮选废水,结合浮选废水的特点(低COD、难降解、高pH),开展了臭氧氧化-生物活性炭吸附工艺处理选矿废水的小试研究。选矿废水中各残留有机药剂及pH对浮选指标的影响研究表明,废水中残留有机药剂及pH对浮选指标均有不同程度的影响。臭氧氧化-生活活性炭吸附工艺处理选矿废水的小试研究表明,水力停留时间为4 h、反应器臭氧浓度为33.3 mg/L,可获得COD去除率57%、pH降低到8的废水处理效果。将处理后的废水回用于选矿,基本消除残留药剂及pH对浮选指标的影响。本研究提供了一种处理浮选废水的新思路,对臭氧生物活性炭工艺处理浮选废水的工业应用具备参考价值。     

混合型污水处理厂原位生物强化脱氮中试及微生物群落结构分析研究

针对混合型污水处理厂进水水质波动大、C/N低、总氮稳定达标困难等共性问题,开发出适宜于低C/N、贫营养等苛刻环境条件的高效脱氮菌剂.现场中试结果表明:经过脱氮菌强化后,生化系统脱氮效率提升8.5百分点,出水平均总氮较强化前下降3 mg/L,出水水质稳定性明显提升,生物强化效果显著.在不补加碳源条件下,深度处理出水总氮完...     

褐煤活性炭吸附处理焦化废水

研究褐煤活性炭吸附处理焦化废水的性能，为褐煤活性炭用于废水处理提供理论依据和技术指导。以河南某气化厂的焦化废水为吸附原水，进行褐煤活性炭对酚吸附性能的静态和动态实验。静态实验表明，褐煤活性炭对酚的吸附性能符合弗兰德里希（Freundlich）吸附方程式。在室温条件下，对于150 mL焦化废水，当活性炭的用量为10 g，吸附反应时间为1 h，酚的去除率可达92%以上。动态实验研究表明，当进水酚浓度为3 800 mg/L，吸附1.5 h，活性炭的吸附容量可达21.38 mg/g。水处理的实验研究表明，利用褐煤制备的活性炭，对焦化废水具有良好的处理效果。     

The effect of heavy metals on the activated sludge process and its microbial community analysis using 16S ribosomal DNA

The effect of heavy metal shock loading on biological treatment systems was studied by traditional methods and molecular biological techniques. Two kinds of SBR (sequence batch reactor) operation units, unacclimated and acclimated activated sludge systems, were studied. The addition of special nutrients and powdered activated carbon (PAC) to stimulate heavy metal uptake and recovery were studied. The kinetic constants could be used to describe the effect of the inhibition of substance utilisation. The results showed that heavy metal shock loading had a greater effect on the unacclimated activated sludge system than on the acclimated one. The special nutrients greatly enhanced the uptake of copper, and the PAC improved sludge settling and decreased the turbidity of the effluent. The variation of dominant species and the diversity of the bacterial community were analysed using 16S ribosomal DNA. Compared with the slight change of dominant species during acclimation by copper, there was a great change in the acclimated system shocked by a high concentration of copper. The results confirmed that the acclimation could improve the resistance of microorganisms to heavy metal toxicity.     

重金属对活性污泥微生物毒性的比较研究

采用发光细菌毒性、活性污泥脱氢酶毒性、硝化抑制毒性3种方法测定Hg、Cd、Zn、Pb 4种重金属对活性污泥微生物的毒性,并对测定结果进行了比较.结果表明,发光细菌毒性测定方法的灵敏度最高,测得的重金属半数有效浓度(ECSO)最低,4种重金属对发光细菌发光强度的抑制程度由大到小顺序依次为Hg>Cd>Zn>Pb;活性污泥脱氢酶毒性和硝化抑制毒性的测定结果与发光细菌毒性测定结果相比,灵敏度相对较低,测得的重金属ECSO相对较高,测得的活性污泥脱氢酶活性的抑制程度由大到小顺序依次为Cd>Hg>Zn>Pb,与测得的活性污泥硝化速率抑制程度大小顺序一致.但2者测得的EC50有所差别.为了更准确的判定重金属对活性污泥微生物的毒性影响.至少应取不同的重金属毒性终点指示指标做一组毒性实验,而不能以发光细菌毒性测定结果作为唯一的判定依据,这可能会过分夸大重金属对污水处理工艺的冲击能力,导致污水处理成本无谓增加.     

pH对污水污泥中污染物浸出的影响

研究pH对污泥中污染物浸出的影响可以为投海过程中海洋水体酸碱性变化对污泥中污染物浸出的影响及其变化规律提供理论依据。为了得出不同pH值对污泥中污染物浸出的影响，采用CEN/TS 14429：2005浸出实验对上海5个污水处理厂脱水污泥中重金属、溶解性有机碳、溶解性硫化物和主要离子的浸出情况进行了研究，同时分别以超纯水和海水为浸提剂研究在相应pH范围内盐度对上述指标浸出的影响。结果表明，Zn、Cd、Pb和As在酸性和碱性条件下浸出量较高，在中性或接近中性条件下浸出量则最低，且海水中Zn和Cd的浸出量比超纯水中高；Cu在碱性条件下的浸出量明显比酸性条件高；在所研究的pH范围内，5个污泥样品中溶解性有机碳的浸出量均随pH的升高而增高；仅酸挥发性硫含量最高的S5在海水中有较明显的溶解性硫化物浸出；部分污泥样品中的氮在酸性纯水中有较高的浸出量，海水中浸出量较少；而无论海水或纯水中，磷在强酸和强碱条件下均有明显浸出。     

生物接触氧化法处理选矿废水的影响因素

选矿废水主要来源于有色金属矿山,具有水量大、悬浮物浓度高、重金属浓度高、有机浮选药剂浓度高等明显特征。选矿废水若直接排放,对环境的危害相当大。采用生物接触氧化法对模拟选矿废水进行了处理实验研究,考察了不同工艺条件对苯胺黑药、黄药及乙硫氮等浮选药剂去除效果的影响,结果表明:接触氧化反应器的最佳停留时间为8 h,进水最佳pH为6～7,葡萄糖投加量为0.1 mg/L时,降解效果达到最佳;此外,接触氧化反应器中微生物承受硫化物的浓度可达到120 mg/L。     

一种新型环境矿物材料在废水处理中的应用研究

实验研究表明 ,磷矿石作为一种新型环境矿物材料对重金属离子工业废水具有较好的处理效果 ,且自身具有显著的优点。采用分级处理的方法以及磷矿石的合适用量可以使处理后的工业废水达到排放标准甚至饮用标准 ,同时 ,由于磷矿石去除重金属离子速度快 ,在瞬间即可发生作用 ,使得利用动态法进行工业废水的连续处理成为可能 ,而且不会产生二次污染 ,具有工艺应用意义     

微波法制备污泥活性炭研究

采用微波加热法,以污水厂剩余污泥为原料,磷酸为污泥活化剂制备污泥活性炭.微波功率、辐照时间和磷酸浓度对污泥活性炭吸附性能具有显著影响,在最佳工艺条件微波功率480 W、辐照时间315 s和磷酸浓度40%条件下制得的活性炭碘值301 mg/g,比表面积168 m2/g,污泥中重金属绝大部分被固化.与传统商品炭相比,污泥炭孔隙结构以中孔为主.利用该活性炭处理城市生活污水处理厂出水,COD去除率可达87%以上,污泥炭的吸附等温线用Langmuir等温吸附模型进行描述.     

Heavy metal in sediments of Ziya River in northern China: distribution,potential risks,and source apportionment

The concentration partitioning between the sediment particle and the interstitial water phase plays an important role in controlling the toxicity of heavy metals in aquatic systems. The aim of this study was to assess the sediment quality in a polluted area of the Ziya River, Northern China. The contamination potential and bioavailability of six metals were determined from the concentrations of total metals and the bioavailable fractions. The results showed that the concentrations of Cr, Cu, Ni, Zn, and Pb exceeded the probable effect concentration at several sites. The high geoaccumulation indices showed that the sediments were seriously contaminated by Cd. The ratio of acid-volatile sulfide (AVS) to simultaneously extracted metal (SEM) was higher than 1, which indicated that the availability of metals in sediments was low. The risk assessment of interstitial waters confirmed that there was little chance of release of metals associated with acid-volatile sulfide into the water column. Values of the interstitial water criteria toxicity unit indicated that none of the concentrations of the studied metals exceeded the corresponding water quality thresholds of the US Environmental Protection Agency. Positive matrix factorization showed that the major sources of metals were related to anthropogenic activities. Further, if assessments are based on total heavy metal concentrations, the toxicity of heavy metals in sediment may be overestimated.     

微波强化Fenton/活性炭工艺处理制药废水的影响因素

为了研究微波强化Fenton/活性炭工艺处理高浓度制药废水的影响因素,以阜新某集团公司生产制药原料排出的废水为研究对象,利用静态实验,采用混凝-微波强化Fenton/活性炭工艺对高浓度制药废水进行实验。实验用水为100 mL、COD为576~1 440 mg/L的制药废水,当活性炭投加量为2 g,H2O2投加量为3/4Qth,pH值为5,微波辐照功率和时间分别为500 W和7 min时,COD去除率可达到92.6%,出水COD在42.6~106.6 mg/L范围内。实验结果表明,活性炭的投加量、H2O2的投加量、pH值、微波辐照功率和辐照时间对微波强化Fenton/活性炭工艺的处理效果影响都较显著。     

硫化沉淀法处理矿山酸性废水研究

对沉淀浮选机理进行了分析 ,讨论了选择性沉淀 浮选技术 ,论述了硫化沉淀浮选法不仅能处理矿山含重金属离子废水 ,同时还能回收其中的有用金属