TiO_2/PTh/Fe_3O_4催化剂制备及光催化与磁回收性能

以聚噻吩磁性微珠PTh/Fe3O4(PF)为载体,采用低温水热法(170℃,pH=7±0.2)在其表面负载TiO2,制备了壳/壳/核结构的磁载光催化剂TiO2/PTh/Fe3O4(TPTF)。用透射电子显微镜(TEM)、X射线衍射仪(XRD)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)对催化剂的形貌、物相组成、表面性质、磁学性质进行了表征。以苯酚为模拟污染物,评价其光催化活性;通过自制的磁回收装置,考察其磁回收特性。结果表明,TiO2晶粒大小在4~6 nm之间,具有混晶结构(锐钛矿型占93.6%,金红石型占6.4%);当nTiO2∶n噻吩单体∶nFe3O4=75∶2.5∶1时,TPTF的催化活性最佳;P25、纯TiO2、TPTF(nTiO2∶n噻吩单体:nFe3O4=75∶2.5∶1)和TiO2/Fe3O4(TF)光催化降解苯酚的速率常数分别是0.0371、0.0302、0.0253和0.0106 min-1;TPTF循环使用5次,其反应速率常数、饱和磁化强度以及磁回收率为0.0205 min-1、1.59emu/g和89.3%,比第1次的0.0253 min-1、1.85 emu/g和94.7%略有降低。     

亚甲基蓝表面修饰纳米TiO2降解造纸废水动力学

以亚甲基蓝(MB)作为表面修饰剂,采用简单的化学吸附法制备亚甲基蓝表面修饰的纳米TiO2光催化剂(TiO2-MB)。经表面修饰后,TiO2-MB光催化剂波长响应范围红移至可见光区575 nm处。探讨了光催化剂量、光照时间和溶液pH值对TiO2-MB光催化降解造纸废水的影响;研究了纳米TiO2-MB对造纸废水的暗吸附规律和光降解性能。结果表明:纳米TiO2-MB对造纸废水的吸附规律都较好地符合Langmuir和Freundlich吸附等温模型,属于吸热反应;光催化降解动力学符合Langmuir-Hinshelwood动力学模型。在160 W高压汞灯光照80 min,3.0 g/L纳米TiO2-MB光催化降解pH=2.0的造纸废水(COD:2 069.8 mg/L),COD去除率可达94.7%,处理效果远高于避光条件下。光催化剂经8次使用仍具有较高的催化活性。     

负载型TiO2固定相光催化降解含酚废水的试验研究

以20W紫外灯为光源,研究了将TiO2粉末负载在硅胶颗粒上,对含酚废水进行光催化降解.由试验得出光催化反应过程中的工艺条件,在此基础上添加H2O2、Fe3+、Cu2+,反应1 h后,苯酚的降解率达95%以上.     

零价铁(Fe~0)共存下TiO_2光催化降解特性的研究

针对TiO2光催化反应中易出现电子-空穴对(e--h+)的复合、而Fenton技术又面临铁污泥的问题,向TiO2光催化反应中加入零价铁(Fe0)。通过调节溶液pH,使Fe0缓释Fe2+,且反应之后的pH仍能满足TiO2光催化反应所需。溶液中的Fe2+,一方面能减弱TiO2光催化产生的e--h+的复合,提高TiO2光催化反应的效率;另一方面,在紫外灯照射下也可以起到光Fenton降解作用。研究结果表明,Fe0共存下TiO2光催化对废水的降解率高于单独使用TiO2光催化或光Fenton对废水的降解率。对Fe0共存下TiO2光催化降解废水的褪色率的动力学研究表明,该反应属于三级动力学反应,且其对有机物的降解具有TiO2光催化和光Fenton加合增效的效果。     

Fe_3O_4/SDS磁性纳米颗粒吸附水体中的Cd~（2＋）和Zn~（2＋）

一种新型纳米固相萃取吸附剂,由阴离子表面活性剂十二烷基磺酸钠（SDS）包裹在Fe3O4磁性纳米颗粒表面形成,用于吸附水溶液中的重金属离子。研究了吸附过程的主要影响因素（如SDS浓度、溶液pH等）以及解吸过程的最佳条件,并对其机理进行了初步的探讨。研究结果表明,共沉淀法制备的Fe3O4颗粒粒径分布均匀,平均粒径约为54 nm;SDS浓度为300 mg/L时,Fe3O4/SDS磁性纳米颗粒吸附Cd2＋和Zn2＋的能力最强;在一定浓度范围内,Fe3O4/SDS体系对Cd2＋和Zn2＋的吸附平衡数据符合Langmuir吸附等温方程,饱和吸附量分别为22.42 mg/g和13.95 mg/g。最终结果表明,Fe3O4/SDS磁性纳米颗粒具有较强磁分离能力和较好的吸附效果。     

Fe3O4/SDS磁性纳米颗粒吸附水体中的Cd2+和Zn2+

一种新型纳米固相萃取吸附剂,由阴离子表面活性剂十二烷基磺酸钠(SDS)包裹在Fe3O4磁性纳米颗粒表面形成,用于吸附水溶液中的重金属离子。研究了吸附过程的主要影响因素(如SDS浓度、溶液pH等)以及解吸过程的最佳条件,并对其机理进行了初步的探讨。研究结果表明,共沉淀法制备的Fe3O4颗粒粒径分布均匀,平均粒径约为54 nm;SDS浓度为300 mg/L时,Fe3O4/SDS磁性纳米颗粒吸附Cd2+和Zn2+的能力最强;在一定浓度范围内,Fe3O4/SDS体系对Cd2+和Zn2+的吸附平衡数据符合Langmuir吸附等温方程,饱和吸附量分别为22.42 mg/g和13.95 mg/g。最终结果表明,Fe3O4/SDS磁性纳米颗粒具有较强磁分离能力和较好的吸附效果。     

Fe/TiO2光催化降解水溶液中的4-氯苯酚

以TiO2-P25及FeC2O4为前驱物制备了Fe3 掺杂TiO2光催化剂--Fe/TiO2.X射线衍射结果表明,500 ℃煅烧温度下的Fe/TiO2主要是锐态矿晶型,当掺Fe3 量为0.5%(质量分数,下同)时,Fe3 以取代掺杂形式进入TiO2晶格,而当掺Fe3 量达5.0%时,则出现α-Fe2O3的特征衍射峰;900 ℃煅烧温度下的Fe/TiO2则均为金红石晶型,掺Fe3 量达2.0%～5.0%时,出现Fe2TiO5的特征衍射峰.4-氯苯酚的光催化实验结果表明,煅烧温度及Fe3 掺杂量对Fe/TiO2的光催化活性有显著影响,以煅烧温度500 ℃及掺Fe3 量0.5%的Fe/TiO2为光催化剂,反应80 min,4-氯苯酚的降解率达100%,总有机碳去除率约95%.     

负载TiO2/Fe3+的玻璃纤维反应器光催化苯酚

以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3+作为掺杂改性离子,形成了负载TiO2/Fe3+的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365～250 W光源照射下,pH为3～5,O2通入量1.0 L/(min.L),反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。     

La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La2O3/ZnO/TiO2复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La2O3/ZnO/TiO2的光催化性能.结果表明:当锌和镧的掺杂量w(zno)=20%,w(La2O3)=0.5%,煅烧温度为500℃时,La2O3/ZnO/TiO2复合光催化剂的光催化活件最高;当催化荆投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La2O3/ZnO/TiO2对活性艳红K-2BP的降解效果最好.实验证明.La2O3/ZnO/TiO2对活性艳红K-2BP的降解遵从Lang-muir-Hinshelwood动力学模型,测得其反应速率常数k=11.5 mg/(L·min);吸附常数K=2.88×10-2L/mg.     

TiO_2/NiFe_2O_4磁性纳米光催化剂的制备及其光催化性能研究

先用水热法制备了纳米级NiFe2O4磁核,然后采用均匀沉淀法在NiFe2O4磁核表面包覆TiO2,制备了一种新型磁性纳米光催化剂TiO2/NiFe2O4。通过实验确定了制备TiO2/NiFe2O4的最佳Ti/Ni(摩尔比)为30/1,用X射线衍射(XRD)、透射电子显微镜(TEM)、紫外—可见(UV—Vis)漫反射、热重—差示扫描量热分析(TG—DSC)、磁力学测试等手段对其进行了表征。以甲基橙的水溶液为模拟污染物,评价了TiO2/NiFe2O4的光催化性能,在光照2h后,甲基橙的脱色率可达98.5%。研究结果表明,TiO2/NiFe2O4是一种可重复使用的高效光催化剂。     

Toxicity of TiO2, ZrO2, Fe,Fe2O3, and Mn2O3 nanoparticles to the yeast, Saccharomyces cerevisiae

The growing application of engineered nanomaterials is leading to an increased occurrence of nanoparticles (NPs) in the environment. Thus, there is a need to better understand their potential impact on the environment. This study evaluated the toxicity of nanosized TiO₂, ZrO₂, Fe⁰, Fe₂O₃, and Mn₂O₃ towards the yeast Saccharomyces cerevisiae based on O₂ consumption and cell membrane integrity. In addition, the state of dispersion of the nanoparticles in the bioassay medium was characterized.     

Degradation of paracetamol by advance oxidation processes using modified reticulated vitreous carbon electrodes with TiO2 and CuO/TiO2/Al2O3

The degradation of paracetamol in aqueous solutions in the presence of hydrogen peroxide was carried out by photochemistry, electrolysis and photoelectrolysis using modified 100 pores per inch reticulated vitreous carbon electrodes. The electrodes were coated with catalysts such as TiO₂ and CuO/TiO₂/Al₂O₃ by electrophoresis followed by heat treatment. The results of the electrolysis with bare reticulated vitreous carbon electrodes show that 90% paracetamol degradation occurs in 4 h at 1.3 V vs. SCE, forming intermediates such as benzoquinone and carboxylic acids followed by their complete mineralisation. When the electrolysis was carried out with the modified electrodes such as TiO₂/RVC, 90% degradation was achieved in 2 h while with CuO/TiO₂/Al₂O₃/RVC, 98% degradation took only 1 h. The degradation was also carried out in the presence of UV reaching 95% degradation with TiO₂/RVC/UV and 99% with CuO/TiO₂/Al₂O₃/RVC/UV in 1 h. The reactions were followed by spectroscopy UV-Vis, HPLC and total organic carbon analysis. These studies show that the degradation of paracetamol follows a pseudo-first order reaction kinetics.     

铁炭微电解-Fe2+/K2S2O8降解甲基橙

针对偶氮类有机物废水具有色度大,难降解的特点,以对二甲基氨基偶氮苯磺酸钠(甲基橙)为模拟研究对象,对水体系中铁炭微电解-Fe2+/K2S2O8降解甲基橙的方法进行了研究。通过正交实验确定出该方法各因素的影响程度,进一步通过单因素影响实验确定该方法的最佳条件是:铁炭微电解填料、FeSO4和K2S2O8投加量分别为300 g/L、1.3mmol/L和0.7 mmol/L,初始pH值为7.0。在最佳条件下,甲基橙COD和色度去除率分别能达到64.7%和68.2%。     

Recycling of iron and silicon from drinking water treatment sludge for synthesis of magnetic iron oxide@SiO<Subscript>2</Subscript> composites

More attention has been paid to the deterioration of water bodies polluted by drinking water treatment sludge (DWTS) in recent years. It is important to develop methods to effectively treat DWTS by avoiding secondary pollution. We report herein a novel investigation for recovery of Si and Fe from DWTS, which are used for the synthesis of two iron oxide@SiO₂ composites for adsorption of reactive red X-3B (RRX-3B) and NaNO₂. The results show that Fe³⁺ (acid-leaching) and Si⁴⁺ (basic-leaching) can be successfully recovered from roasted DWTS. Whether to dissolve Fe(OH)₃ precipitation is the key point for obtaining Fe₃O₄ or γ-Fe₂O₃ particles using the solvothermal method. The magnetic characteristics of Fe₃O₄@SiO₂ (390.0 m² g^?1) or Fe₂O₃@SiO₂ (220.9 m² g^?1) are slightly influenced by the coated porous SiO₂ layer. Peaks of Fe–O stretching vibration (580 cm^?1) and asymmetric Si–O–Si stretching vibrations (1080 cm^?1) of Fe₃O₄@SiO₂ indicate the successful coating of a thin silica layer (20–150 nm). The adsorption capacity of RRX-3B and NaNO₂ by Fe₃O₄@SiO₂ is better than that of Fe₂O₃@SiO₂, and both composites can be recycled through an external magnetic field. This method is an efficient and environmentally friendly method for recycling DWTS.     

Cu/La共掺杂TiO2光催化氧化水中的氨氮

采用水解-沉淀法制备了Cu/La共掺杂纳米TiO2催化剂,利用XRD、XPS和BET技术对其进行表征,并考察了在紫外灯下,共掺杂TiO2对氨氮的光催化氧化工艺条件。物相结构和比表面积测试结果表明,共掺杂催化剂具有较好的锐钛矿晶型,孔径分布为4～8 nm,Cu/La共掺杂TiO2La以La3+,Cu是以Cu2+、Cu+的形式掺杂进入TiO2的晶格。光催化实验表明:所得改性光催化剂对氨氮的去除及焦化废水的处理均具有较高的催化活性。     

Synthesis, properties and application research of atrazine Fe3O4@SiO2 magnetic molecularly imprinted polymer

Introduction

Magnetic Fe₃O₄ nanoparticles were prepared by coprecipitation and then were coated with SiO₂ on the surface.

Materials and methods

Fe₃O₄@SiO₂ composite microspheres were modified by KH570. Using molecular imprinting technology, atrazine magnetic molecularly imprinted polymer was prepared by using atrazine as template molecule, methacrylic acid as functional monomer and ethylene glycol dimethacrylate as cross-linkers. The morphology, composition and magnetic properties of magnetic nanoparticles were characterized. The recognition selectivity of polymer was studied for template molecule and simulation by UV spectrophotometry. The adsorption properties and selectivity ability were analyzed by Scatchard analysis.

Results

Scatchard linear regression analysis indicated that there are two binding sites of the target molecules. The magnetic molecularly imprinted polymer has been applied to the analysis of atrazine in real samples.

Conclusion

The results show that: the recovery rates and the relative standard deviation were 94.0??98.7% and 2.1??4.0% in corn, the recovery rates and the relative standard deviation were 88.7??93.5% and 2.8??7.2% in water.     

TiO2纳米管催化活性再生处理技术简

采用H₂O₂、Fe₂（SO₄）₃和Fenton溶液对失活的TiO₂纳米管进行再生处理，重点考察了3种溶液的浓度和处理时间等对再生效果的影响，初步分析了经处理后TiO₂纳米管催化活性得到再生或增强的机理。结果表明，经H₂O₂溶液处理后TiO₂催化活性能得到有效再生，经Fe₂（SO₄）₃和Fenton溶液处理后其催化活性不仅得到再生，还能显著增强，这与H₂O₂和Fenton的强氧化作用，及进入TiO₂纳米管的Fe³⁺的阻止电子-空穴对再复合作用有关。     

纳米Bi2O3/TiO2复合光催化剂的制备及性能研究

以光催化效果为评价标准，采用超声波作用下水解法制备Bi₂O₃/TiO₂复合光催化剂，考察了水解条件和Bi₂O₃掺入量等制备条件对复合光催化剂性能的影响。结果表明，与传统制备方法相比，该方法操作简单、快速；当水和乙醇的比例为4∶1时所得样品的光催化活性最好；Bi₂O₃的掺入拓宽了TiO₂对光的吸收范围，提高了TiO₂的光催化活性，掺入量(Bi₂O₃)为0.25%复合光催化剂催化活性最高；复合光催化剂对多种水溶性染料均具有较好的处理效果。     

UV/H2O2/Fe-FeOxH2x-3和UV/H2O2工艺降解水中富里酸的研究

采用硼氢化钠还原法制备核-壳结构的Fe-FeO_xH_2x-3复合材料，研究了富里酸在UV/H₂O₂和UV/H₂O₂/Fe-FeO_xH_2x-3两种不同反应体系下的降解情况。结果表明，核-壳结构Fe-FeO_xH_2x-3的存在，提高了UV/H₂O₂降解富里酸的反应速率，TOC去除达到84%。采用XAD树脂吸附法对反应前后的富里酸进行化学分级表征，结果表明，富里酸经反应后憎水酸（HoA）、弱憎水酸（WHoA）和憎水中性物质（HoN）都有所减少，进而转化为亲水性物质（HiM）；用超滤膜法对富里酸进行物理分级表征，考察了富里酸在反应前后分子量分布的变化情况。同时，富里酸经过反应后生成的中间产物降低了三氯甲烷生成趋势。     

UV/H_2O_2/TiO_2联合水解酸化+MBR工艺处理亚砜废水

二甲基亚砜(DMSO)废水因其COD高、可生化性差的特性而较难处理。本实验以采用硫酸二甲酯法生产DMSO的某化工厂废水为研究对象,设计并建立了组合式光催化氧化装置联合水解酸化+MBR工艺的中试系统,探讨了组合式光催化氧化装置、氧化剂投加量、pH、反应时间和水力停留时间对系统处理效果的影响。结果表明,组合式光催化氧化装置可有效提高DMSO废水的可生化性。最优工艺参数为:按H2O2与原水COD质量浓度比为2∶1投加H2O2,在pH值为4、反应时间为6 h、水力停留时间为4 h的条件下,该系统对原水COD(5 000 mg/L)去除率大于98%,出水COD达到《污水综合排放标准》(GB 8978-1996)一级要求。