Refinery Sludge Treatment/Hazardous Waste Minimization Via Dehydration and Solvent Extraction

Abstract

The patented Carver-Greenfield (C-G) Process®, a combination of dehydration and solvent extraction treatment technologies, has a wide range of uses in separating hydrocarbon solvent-soluble hazardous organic contaminants (indigenous oil) from sludges, soils, and industrial wastes. As a result of this treatment, the products from a C-G Process facility are: ? Clean, dry solids which are typically suitable for disposal in nonhazardous landfills;

? Water which is treatable in an industrial or Publicly Owned Treatment Works (POTW) wastewater treatment facility;

? Extracted indigenous oil containing hydrocarbon soluble contaminants which may be recycled or reused or disposed of at less cost because its volume is smaller than the original waste feed.

The C-G Process was demonstrated on spent oily drilling fluids as part of the U.S. Environmental Protection Agency Superfund Innovative Technology Evaluation (SITE) Program. This paper summarizes the use of the C-G Process for economical treatment and minimization of hazardous refinery wastes, reviews the SITE program results, and describes extending the C-G Process technology to treatment of other wastes. Estimated treatment costs are presented.     

Avoiding Land Disposal of Hazardous Waste

In response to a growing societal mandate, land disposal of hazardous wastes is gradually being replaced by treatment technologies. This shift to "alternative technologies" is the result of the impacts of past land disposal practices on other environmental media (groundwater, surface water, and air). A prime motivation for adopting alternatives to land disposal is to eliminate these cross-media impacts. Alternative technologies, however, can themselves have cross-media environmental impacts which must be recognized and addressed before such technologies are extensively applied. This paper discusses hazardous waste constituents, common disposal practices, alternative technologies currently being applied, possible cross-media environmental impacts of the alternative technologies, and proposed methods of mitigating these environmental impacts. Case studies from uncontrolled hazardous waste sites and industrial operations are used to illustrate the application of alternative technologies. Case studies include the application of waste treatment technologies as well as the adoption of waste minimization techniques.     

Influences of human waste–based ectopic fermentation bed fillers on the soil properties and growth of Chinese pakchoi

The reuse of human wastes as biofertilizer resources offers a new option for meeting the growing demand for food and addressing poor soil productivity. Feces and black water are ubiquitous human wastes that usually require proper treatment, such as composting and anaerobic digestion, to remove potentially harmful substances before they can be applied as fertilizers. As an effective treatment technology for livestock farming wastes, the ectopic fermentation bed system (EFS) provides a new means of treating human waste and producing organic fertilizer from decomposed filler. Therefore, the objective of this study was to evaluate and compare the nutrient content and fertilizer potential of decomposed fillers obtained after EFS treatment of human feces and black water under different application conditions. The results showed that the application of fillers increased the yield of pakchoi by 3.60?29.32% and nutrient uptake by 8.09?83.45% compared to the CK, which could effectively promote the growth of pakchoi. This approach also improved the quality of pakchoi and enhanced soil fertility, and differences were observed in the effects of different kinds and application amounts of fillers. Soil EC was the soil property that had the greatest effect on the growth characteristics of pakchoi in this study. These findings help to better clarify the agronomic value of human wastes, but the effects of long-term filler application need to be further explored.

     

A review on the conversion of cassava wastes into value-added products towards a sustainable environment

The solid and liquid wastes generated from cassava-based industries are organic and acidic in nature, which leads to various global concerns—primarily global warming and biodiversity loss. But the conversion of these wastes into value-added products associated with environmental pollution control contributes to sustainable development. Generally, the thermochemical process such as pyrolysis and gasification and biochemical processes such as anaerobic digestion have been applied for the conversion of cassava waste into value-added products. This review addresses the valorization of cassava wastes, which fulfill almost all needs of the hour, such as energy (biofuel), wastewater treatment (adsorbents), bioplastics, starch nanoparticles, organic acid production, and antimicrobial agents. The major aim of this paper is to analyze and provide the disclosure of the efficiency of cassava-based industrial waste as a source to minimize the problem associated with conventional fossil fuels and through which mitigate the impact of global warming and climate change. Furthermore, recent research and achievements in the valorization of cassava waste have been highlighted.

     

Medical Waste Disposal

Medical (biomedical) wastes pose numerous potential health and safety hazards. In addition to their infectious and toxic characteristics, the highly variable and inconsistent nature of medical waste streams has increased public concern about storage, treatment, transportation, and ultimate disposal.

In recent years, techniques have been developed to reduce human exposure to the toxic and infectious components of medical wastes. The most commonly used techniques include internal segregation, containment, and incineration. Other common techniques include grinding, shredding, and disinfection, e.g., autoclaving and chemical treatment followed by landfilling.

Of all the available technologies for medical waste treatment and disposal, incineration has been found to be the most effective method overall for destroying infectious and toxic material, volume reduction, and weight reduction in the medical waste stream, incineration destroys the broadest variety of medical waste constituents and can recover energy from the medical waste stream. Incineration also is an appropriate alternative to burial of human pathological remains.     

Healthcare waste management practice in the West Black Sea Region,Turkey: A comparative analysis with the developed and developing countries

The need for proper healthcare waste management has been a crucial issue in many developing countries as it is in Turkey. The regulation regarding healthcare wastes in Turkey was updated in 2005 in accordance with the European Union (EU) waste directives, but it still falls behind meeting the requirements of current waste treatment technologies. Therefore, this study aims to reveal deficiencies, inconsistencies, and improper applications of healthcare waste management in the western part of the Turkish Black Sea Region. In this study, it was revealed that nearly 1 million people live in the region, resulting in 5 million hospital admissions annually. All the healthcare waste produced (1000 tons yr^?1) is treated in an autoclave plant. However, treating some categories of healthcare wastes in autoclave units mismatches with the EU waste regulations, as alternative treatment technologies are not technically able to treat all types of healthcare wastes. A proper waste management system, therefore, requires an internal segregation scheme to divert these wastes from the main healthcare waste stream. The existing malpractice in the region could cause serious health problems if no measure is taken urgently. It is expected that healthcare waste management in the region and then all across Turkey will be improved with the significant deficiencies and inconsistencies pointed out in this research.

Implications:?In developed countries, specific rules and regulations have already been implemented along with the recommendations for handling of healthcare waste. However, in Turkey, these wastes are treated in autoclave units, which mismatches with the European Union waste regulations, as alternative treatment technologies are not technically capable to treat all types of healthcare wastes. The existing malpractice could cause serious health problems if no measure is taken urgently. The authors demonstrated the existing status of Turkish waste management and revealed deficiencies, inconsistencies, and improper applications in comparison with developed and developing nations to align Turkish practice to European Union requirements.     

Using phytoremediation technologies to upgrade waste water treatment in Europe

Goal, Scope and Background One of the burning problems of our industrial society is the high consumption of water and the high demand for clean drinking water. Numerous approaches have been taken to reduce water consumption, but in the long run it seems only possible to recycle waste water into high quality water. It seems timely to discuss alternative water remediation technologies that are fit for industrial as well as less developed countries to ensure a high quality of drinking water throughout Europe. Main Features The present paper discusses a range of phytoremediation technologies to be applied in a modular approach to integrate and improve the performance of existing wastewater treatment, especially towards the emerging micro pollutants, i.e. organic chemicals and pharmaceuticals. This topic is of global relevance for the EU. Results Existing technologies for waste water treatment do not sufficiently address increasing pollution situation, especially with the growing use of organic pollutants in the private household and health sector. Although some crude chemical approaches exist, such as advanced oxidation steps, most waste water treatment plants will not be able to adopt them. The same is true for membrane technologies. Discussion Incredible progress has been made during recent years, thus providing us with membranes of longevity and stability and, at the same time, high filtration capacity. However, these systems are expensive and delicate in operation, so that the majority of communities will not be able to afford them. Combinations of different phytoremediation technologies seem to be most promising to solve this burning problem. Conclusions To quantify the occurrence and the distribution of micropollutants, to evaluate their effects, and to prevent them from passing through wastewater collection and treatment systems into rivers, lakes and ground water bodies represents an urgent task for applied environmental sciences in the coming years. Recommendations Public acceptance of green technologies is generally higher than that of industrial processes. The EU should stimulate research to upgrade existing waste water treatment by implementing phytoremediation modules and demonstrating their reliability to the public.     

Public Policy impacts on the Generation and Disposal of Hazardous Waste in New York State

A number of policies adopted by the federal government and the states have been designed to promote waste reduction or influence the choice of waste disposal technologies employed by generators of hazardous waste. Graphic analysis of smoothed time series data for hazardous wastes manifested in New York State for the period between June 1982 and February 1987 suggests that some of these policies have had the intended effects.

Significant shifts in manifested waste volumes are evident that coincide with the following policy interventions: (1) increased state waste-end tax rates; (2) state and federal landfill bans; (3) federal restrictions on burning hazardous wastes and waste oils for energy recovery; and (4) changes in the federal regulatory definition of hazardous waste. Other changes in waste generation and management appear to be attributable to such factors as state and regional economic conditions and changes in instate treatment and disposal facility capacity. Analysis of the management of specific waste types supports evidence from the graphic analysis that waste generators changed from land disposal to “higher” waste handling technologies in response to several policy interventions.     

Emerging trends in photodegradation of petrochemical wastes: a review

Various human activities like mining and extraction of mineral oils have been used for the modernization of society and well-beings. However, the by-products such as petrochemical wastes generated from such industries are carcinogenic and toxic, which had increased environmental pollution and risks to human health several folds. Various methods such as physical, chemical and biological methods have been used to degrade these pollutants from wastewater. Advance oxidation processes (AOPs) are evolving techniques for efficient sequestration of chemically stable and less biodegradable organic pollutants. In the present review, photocatalytic degradation of petrochemical wastes containing monoaromatic and poly-aromatic hydrocarbons has been studied using various heterogeneous photocatalysts (such as TiO₂, ZnO and CdS. The present article seeks to offer a scientific and technical overview of the current trend in the use of the photocatalyst for remediation and degradation of petrochemical waste depending upon the recent advances in photodegradation of petrochemical research using bibliometric analysis. We further outlined the effect of various heterogeneous catalysts and their ecotoxicity, various degradation pathways of petrochemical wastes, the key regulatory parameters and the reactors used. A critical analysis of the available literature revealed that TiO₂ is widely reported in the degradation processes along with other semiconductors/nanomaterials in visible and UV light irradiation. Further, various degradation studies have been carried out at laboratory scale in the presence of UV light. However, further elaborative research is needed for successful application of the laboratory scale techniques to pilot-scale operation and to develop environmental friendly catalysts which support the sustainable treatment technology with the “zero concept” of industrial wastewater. Nevertheless, there is a need to develop more effective methods which consume less energy and are more efficient in pilot scale for the demineralization of pollutant.     

Treatment of Nonhazardous Petroleum-Contaminated Soils by Thermal Desorption Technologies

Spills, leaks, and accidental discharges of petroleum products have contaminated soil at thousands of sites in the United States. One remedial action technique for treating petroleum contaminated soil is the use of thermal desorption technologies.

This paper describes key elements of the U.S. Environmental Protection Agency report titled “Thermal Desorption Applications Manual for Treating Nonhazardous Petroleum Contaminated Soils.”¹ The applications manual describes the types, mechanical and operating characteristics of thermal desorption technologies that are commercially available to treat petroleum-contaminated soils. It also provides step-by-step procedures to rate the critical success factors influencing the general applicability of thermal desorption at a particular site. These factors include site, waste and soil characteristics, regulatory requirements, and process equipment design and operating characteristics. Procedures are provided to determine the types of thermal desorption systems that are most technically suitable for a given application and to determine whether on-site or off-site treatment is likely to be the most cost-effective alternative. Key factors that determine process economics are identified, and estimated cost ranges for treating petroleum-contaminated soils are presented. Spreadsheets are provided that can be used for performing cost analyses for specific applications.

The aforementioned report is applicable only to the treatment of petroleum-contaminated soils that are exempt from being classified as hazardous wastes under the Resource Conservation and Recovery Act (RCRA) or as toxic materials under the Toxic Substances Control Act (TSCA). Although much of the technical discussion in this paper is applicable to the treatment of both nonhazardous and hazardous ortoxic materials, permitting requirements and treatment costs are significantly different forthe individual categories of waste materials.     

Analysis of Industrial Boiler Solid Waste Impacts

This paper presents an examination of industrial coal-fired boiler waste products. Presently the atmospheric emissions from all new boilers larger than 250 × 10⁶ Btu/hr are controlled by existing New Source Performance Standards, and boilers smaller than 250 × 10⁶ Btu/hr are controlled to levels required by the regulations of the particular state in which the facility is located. The 1977 Clean Air Act Amendments, however, specify categories of sources for which EPA must develop revised New Source Performance Standards. Industrial coal-fired boilers are included as one of these categories, and a relevant issue concerns the potential amount of solid waste generated as a result of tightened emission standards that require flue gas desulfurization. This paper examines the air quality and solid waste impacts of moderate and stringent emission controls for particulate and SO₂ emissions from industrial coal-fired boilers.

Comparisons are presented of physical and chemical characterizations of the emissions and solid wastes produced when boilers are equipped with particulate and SO₂ control equipment. The SO₂ systems examined are lime spray drying, lime/limestone, double alkali, sodium throwaway, physically cleaned coal, and fluidized-bed combustion. The solid waste disposal alternatives and the disposal costs are discussed. The most common disposal methods used are landfill for dry wastes and impoundment for sludges, with special wastewater treatment requirements for the sodium throwaway aqueous wastes.     

Characterization of Products from Fluidized-Bed Combustion of Coal

ABSTRACT

The technology of fluidized-bed combustion (FBC) of coal generates byproducts that have a series of unique characteristics and potential uses in technological practice. In this study, the products of fluidized-bed combustion (FBC-P) of coal derived from Moravian heat stations, a.s. Zlin, Cinergy Global Resources, Czech Republic, were characterized. Particular attention was paid to determining the chemical composition of FBC-P, the content of polycyclic aromatic hydrocarbons (PAHs) and toxic metals in the water leachates of these FBC-P, the content of unburned carbon, the capability of FBC-P to solidify with water and form a solid matrix, and the method for discovering optimum mixing water content for FBC-P solidification. The results suggest that one of the qualitatively more important means of utilizing FBC-P could be their application during solidification/stabilization (S/S) of wastes, particularly wastewa-ter treatment sludges.     

China’s industrial gray water footprint assessment and implications for investment in industrial wastewater treatment

Industrial wastewater is the largest contributor of toxic pollutants and third-largest contributor of nutrients to bodies of water in China, and understanding the characteristics of such pollution is important for water pollution control. In this study, the industrial gray water footprint (GWF) of each industry sector in China’s 31 provinces in 2015 was calculated to identify the pollution characteristics of industrial wastewater discharge and determine how to efficiently allocate investment to pollution reduction. We show that the total industrial GWF of China was 300 billion m³ in 2015 and that the major pollutants were petroleum pollutant (PP), ammonia nitrogen (NH₃-N), volatile phenol (VP), and chemical oxygen demand (COD). The water pollution level (WPL) was higher than 1 in Ningxia, Shanxi, Hebei, Tianjin, Shanghai, Henan, and Shandong, indicating that industrial pollution exceeded the carrying capacity of local water bodies in these seven regions. Given equivalent total investment, a scenario that takes the total reduction of the industrial GWF weighted by the WPL in each region as the investment target can better allocate funds to control industrial wastewater pollution in regions with high WPLs relative to a scenario in which investment targets the reduction of the unweighted total industrial GWF. For further industrial GWF reduction in regions with high WPLs, it is crucial to adjust the industrial structure and to upgrade relevant technologies.

     

Removal and degradation of aromatic compounds from a highly polluted site by coupling soil washing with photocatalysis

The possible application of two environmental remediation technologies - soil washing and photocatalysis - to remove and decompose various aromatic pollutants present in excavated soils of a contaminated industrial site has been investigated. Aqueous solutions containing the non-ionic surfactant Brij 35 were used to extract the contaminants from the soil samples. The photocatalytic treatment of the obtained washing wastes, performed in the presence of TiO(2) suspensions irradiated with simulated sunlight, showed a slow abatement of the toxic compounds due to the relevant concentrations of organics in the waste. A neat improvement of the process performances, obtained by operating in the presence of added potassium peroxydisulfate, suggests a feasible treatment route.     

Palm oil mill effluent treatment and CO<Subscript>2</Subscript> sequestration by using microalgae—sustainable strategies for environmental protection

In this era of globalization, various products and technologies are being developed by the industries. While resources and energy are utilized from processes, wastes are being excreted through water streams, air, and ground. Without realizing it, environmental pollutions increase as the country develops. Effective technology is desired to create green factories that are able to overcome these issues. Wastewater is classified as the water coming from domestic or industrial sources. Wastewater treatment includes physical, chemical, and biological treatment processes. Aerobic and anaerobic processes are utilized in biological treatment approach. However, the current biological approaches emit greenhouse gases (GHGs), methane, and carbon dioxide that contribute to global warming. Microalgae can be the alternative to treating wastewater as it is able to consume nutrients from wastewater loading and fix CO₂ as it undergoes photosynthesis. The utilization of microalgae in the system will directly reduce GHG emissions with low operating cost within a short period of time. The aim of this review is to discuss the uses of native microalgae species in palm oil mill effluent (POME) and flue gas remediation. In addition, the discussion on the optimal microalgae cultivation parameter selection is included as this is significant for effective microalgae-based treatment operations.     

Atmospheric mercury emissions from waste combustions measured by continuous monitoring devices

Atmospheric mercury emissions have attracted great attention owing to adverse impact of mercury on human health and the ecosystem. Although waste combustion is one of major anthropogenic sources, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated atmospheric emissions of speciated mercury from the combustions of municipal solid wastes (MSW), sewage treatment sludge (STS), STS with waste plastics, industrial waste mixtures (IWM), waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form at the inlet side of air pollution control devices in all combustion cases. Its concentration was 2.0–70.6 times larger than elemental mercury concentration. In particular, MSW, STS, and IWM combustions emitted higher concentration of reactive gaseous mercury. Concentrations of both gaseous mercury species varied greatly for all waste combustions excluding woody waste. Variation coefficients of measured data were nearly equal to or more than 1.0. Emission factors of gaseous elemental mercury, reactive gaseous mercury, and total mercury were calculated using continuous monitoring data. Total mercury emission factors are 0.30 g-Hg/Mg for MSW combustion, 0.21 g-Hg/Mg for STS combustion, 0.077 g-Hg/Mg for STS with waste plastics, 0.724 g-Hg/Mg for industrial waste mixtures, 0.028 g-Hg/Mg for waste plastic combustion, and 0.0026 g-Hg/Mg for woody waste combustion. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.

Implications Although waste combustion is one of major anthropogenic sources of atmospheric mercury emission, estimated emission might have large uncertainty due to great heterogeneity of wastes. This study investigated speciated mercury emissions from the combustions of municipal solid wastes, sewage treatment sludge with/without waste plastics, industrial waste mixtures, waste plastics from construction demolition, and woody wastes using continuous monitoring devices. Reactive gaseous mercury was the major form in all combustion cases and its concentration in the gas had large fluctuation. All emission factors evaluated in this study were comparable or lower than other reported data. Emission inventory using old emission factors likely causes an overestimation.     

Nitrate contamination in water resources,human health risks and its remediation through adsorption: a focused review

The level of nitrate in water has been increasing considerably all around the world due to vast application of inorganic nitrogen fertiliser and animal manure. Because of nitrate’s high solubility in water, human beings are getting exposed to it mainly through various routes including water, food etc. Various regulations have been set for nitrate (45–50 mgNO₃^?/L) in drinking water to protect health of the infants from the methemoglobinemia, birth defects, thyroid disease, risk of specific cancers, i.e. colorectal, breast and bladder cancer caused due to nitrate poisoning. Different methods like ion exchange, adsorption, biological denitrification etc. have the ability to eliminate the nitrate from the aqueous medium. However, adsorption process got preference over the other approaches because of its simple design and satisfactory results especially with surface modified adsorbents or with mineral-based adsorbents. Different types of adsorbents have been used for this purpose; however, adsorbents derived from the biomass wastes have great adsorption capacities for nitrate such as tea waste-based adsorbents (136.43 mg/g), carbon nanotube (142.86 mg/g), chitosan beads (104 mg/g) and cetyltrimethylammonium bromide modified rice husk (278 mg/g). Therefore, a thorough literature survey has been carried out to formulate this review paper to understand various sources of nitrate pollution, route of exposure to the human beings, ill effects along with discussing the key developments as well as the new advancements reported in procuring low-cost efficient adsorbents for water purification.

     

Production of sludge-incorporated paver blocks for efficient waste management

Waste management plays a vital role in the reuse of industry wastes in to useful conversions. The treatment of effluents from the combined textile effluent treatment plant and hypo sludge from the paper industry results in sludge generation, which poses a huge challenge for its disposal. Therefore, an eco-friendly attempt is made to utilize them in the production of paver blocks. Paver blocks are construction units that have vast applications in street roads, walking paths, fuel stations, and so on. In this study, an innovative attempt has been made to manufacture paver blocks incorporating textile effluent treatment plant sludge and hypo sludge, to utilize them in suitable proportions. The effect of adding silica fume and polypropylene fibre in paver blocks has also been studied. Paver blocks containing sludge with different proportions were cast based on the recommendations in Indian Standards (IS) 15658, and the test results were compared with the nominal M20 grade and M30 grade paver blocks. The outcomes of the paver block combinations were studied and found to be an effective utilization of sludge with substantial cement replacement of up to 35%, resulting in effective waste management for specific industries.

Implications: Presently, paver blocks are construction units that have vast application in street roads and other constructions like walking paths, fuel stations, and so on. Also, paver blocks possess easy maintenance during breakages. Based on this application, an innovative attempt has been made to manufacture paver blocks incorporating textile effluent treatment plant sludge and hypo sludge to utilize them in suitable proportions.     

Automated Economic Analysis Model For Hazardous Waste Minimization

Abstract

The U.S. Army has established a policy of achieving a 50 percent reduction in hazardous waste generation by the end of 1992. To assist the Army in reaching this goal, the Environmental Division of the U.S. Army Construction Engineering Research Laboratory (USACERL) designed the Economic Analysis Model for Hazardous Waste Minimization (EAHWM). The EAHWM was designed to allow the user to evaluate the life cycle costs for various techniques used in hazardous waste minimization and to compare them to the life cycle costs of current operating practices. The program was developed in C language on an IBM compatible PC and is consistent with other pertinent models for performing economic analyses. The potential hierarchical minimization categories used in EAHWM Include source reduction, recovery and/or reuse, and treatment. Although treatment is no longer an acceptable minimization option, its use is widespread and has therefore been addressed in the model. The model allows for economic analysis for minimization of the Army’s six most important hazardous waste streams. These include, solvents, paint stripping wastes, metal plating wastes, industrial waste-sludges, used oils, and batteries and battery electrolytes. The EAHWM also includes a general application which can be used to calculate and compare the life cycle costs for minimization alternatives of any waste stream, hazardous or non-hazardous. The EAHWM has been fully tested and implemented in more than 60 Army installations in the United States.     

Alternating Current Electrocoagulation for Superfund Site Remediation

Abstract

The Superfund Innovative Technology Evaluation (SITE) Emerging Technology (ET) Program, authorized under the Superfund Amendments and Reauthorization Act (SARA) of 1986, implements the goal of the SITE Program to promote, accelerate the development of, and make commercially available alternative innovative treatment technologies for use at Superfund sites.

Under this program, the technical and economical feasibility of alternating current electrocoagulation (ACE) developed by Electro-Pure Systems, Inc., was evaluated for a two-year period. ACE is an electrochemical technology where highly-charged aluminum polyhydroxide species are introduced into aqueous media for the removal of suspended solids, oil droplets and soluble ionic pollutants. ACE can break stable aqueous colloidal suspensions of up to 10 percent total solids and stable emulsions containing up to 5 percent oil.

Major operating parameters have been defined for different classes of effluents based on experimental results using complex synthetic soil slurries and metals. Test results indicate that ACE produces aqueous and solid separations comparable to those produced by chemical flocculent additions, but with reduced filtration times and sludge volumes. The technology has application where removal of soluble and suspended pollutants from effluents is required, and in the recovery of fine-grained products from process streams. The technology, however, has not yet been demonstrated at full-scale for Superfund site remediation. The principal results of the SITE research program, and results of ACE treatment on some different classes of industrial effluents not part of the SITE Program, are summarized.