An assessment of indoor air quality in recent Mexican immigrant housing in Commerce City, Colorado

An indoor air quality assessment was conducted on 100 homes of recent Mexican immigrants in Commerce City, Colorado, an urban industrial community north of Denver. Head of households were administered a family health survey, filled out an activity diary, and participated in a home inspection. Carbon monoxide (CO) and carbon dioxide (CO₂) were measured for 24 h inside the main living area and outside of the homes. Harvard Impactors were used to collect 24-h samples of PM_2.5 at the same locations for gravimetric analysis. Dust samples were collected by vacuuming carpeting and flooring at four locations within the home and analyzed by ELISA for seven allergens. Mean indoor and outdoor PM_2.5 levels were 27.2 and 8.5 μg m⁻³, respectively. Indoor PM_2.5 and CO₂ were elevated in homes for which the number of hours with door/window open was zero compared to homes in which the number of hours was high (>15 h). Indoor PM_2.5 levels did not correlate with outdoor levels and tended to increase with number of inhabitants, and results indicate that the source of indoor particles were occupants and their activities, excluding smoking and cooking. Mean indoor CO₂ and CO levels were 1170 and 2.4 ppm, respectively. Carbon monoxide was higher than the 24-h National Ambient Air Quality Standard in 3 of the homes. The predominant allergens were cat (Fel d 1) and mouse (Mus m 1) allergens, found in 20 and 34 homes, respectively.     

Results from a pilot-scale air quality study in Addis Ababa, Ethiopia

Twenty-one samples were collected during the dry season (26 January–28 February 2004) at 12 sites in and around Addis Ababa, Ethiopia and analyzed for particulate matter with aerodynamic diameter <10 μm (PM₁₀) mass and composition. Teflon-membrane filters were analyzed for PM₁₀ mass and concentrations of 40 elements. Quartz-fiber filters were analyzed for chloride, sulfate, nitrate, and ammonium ions as well as elemental carbon (EC) and organic carbon (OC) content. Measured 24-h PM₁₀ mass concentrations were <100 and 40 μg m⁻³ at urban and suburban sites, respectively. PM₁₀ lead concentrations were <0.1 μg m⁻³ for all samples collected, an important finding because the government of Ethiopia had stopped the distribution of leaded gasoline a few months prior to this study. Mass concentrations reconstructed from chemical composition indicated that 34–66% of the PM₁₀ mass was due to geologically derived material, probably owing to the widespread presence of unpaved roads and road shoulders. At urban sites, EC and OC compounds contributed between 31% and 60% of the measured PM₁₀ while at suburban sites carbon compounds contributed between 24% and 26%. Secondary sulfate aerosols were responsible for <10% of the reconstructed mass in urban areas but as much as 15% in suburban sites, where PM₁₀ mass concentrations were lower. Non-volatile particulate nitrate, a lower limit for atmospheric nitrate, constituted <5% and 7% of PM₁₀ at the urban and suburban sites, respectively. At seven of the 12 sites, real-time PM₁₀ mass, real-time carbon monoxide (CO), and instantaneous ozone (O₃) concentrations were measured with portable nephelometers, electrochemical analyzers, and indicator test sticks, respectively. Both PM₁₀ and CO concentrations exhibited daily maxima around 7:00 and secondary peaks in the late afternoon and evening, suggesting that those pollutants were emitted during periods associated with motor-vehicle traffic, food preparation, and heating of homes. The morning concentration maxima were likely accentuated by stable atmospheric conditions associated with overnight surface temperature inversions. Ozone concentrations were measured near mid-day on filter sample collection days and were in all cases <45 parts per billion.     

Long-term variation of PM2.5 levels and composition at rural, urban, and roadside sites in Hong Kong: Increasing impact of regional air pollution

Long-term study of air pollution plays a decisive role in formulating and refining pollution control strategies. In this study, two 12-month measurements of PM_2.5 mass and speciation were conducted in 00/01 and 04/05 to determine long-term trend and spatial variations of PM_2.5 mass and chemical composition in Hong Kong. This study covered three sites with different land-use characteristics, namely roadside, urban, and rural environments. The highest annual average PM_2.5 concentration was observed at the roadside site (58.0±2.0 μg m⁻³ (average±2σ) in 00/01 and 53.0±2.7 μg m⁻³ in 04/05), followed by the urban site (33.9±2.5 μg m⁻³ in 00/01 and 39.0±2.0 μg m⁻³ in 04/05), and the rural site (23.7±1.9 μg m⁻³ in 00/01 and 28.4±2.4 μg m⁻³ in 04/05). The lowest PM_2.5 level measured at the rural site was still higher than the United States’ annual average National Ambient Air Quality Standard of 15 μg m⁻³. As expected, seasonal variations of PM_2.5 mass concentration at the three sites were similar: higher in autumn/winter and lower in summer. Comparing PM_2.5 data in 04/05 with those collected in 00/01, a reduction in PM_2.5 mass concentration at the roadside (8.7%) but an increase at the urban (15%) and rural (20%) sites were observed. The reduction of PM_2.5 at the roadside was attributed to the decrease of carbonaceous aerosols (organic carbon and elemental carbon) (>30%), indicating the effective control of motor vehicle emissions over the period. On the other hand, the sulfate concentration at the three sites was consistent regardless of different land-use characteristics in both studies. The lack of spatial variation of sulfate concentrations in PM_2.5 implied its origin of regional contribution. Moreover, over 36% growth in sulfate concentration was found from 00/01 to 04/05, suggesting a significant increase in regional sulfate pollution over the years. More quantitative techniques such as receptor models and chemical transport models are required to assess the temporal variations of source contributions to ambient PM_2.5 mass and chemical speciation in Hong Kong.     

Assessment of traffic-related air pollution in the urban streets before and during the 2008 Beijing Olympic Games traffic control period

In order to investigate the air quality and the abatement of traffic-related pollution during the 2008 Olympic Games, we select 12 avenues in the urban area of Beijing to calculate the concentrations of PM₁₀, CO, NO₂ and O₃ before and during the Olympic traffic controlling days, with the OSPM model.Through comparing the modeled results with the measurement results on a representative street, the OSPM model is validated as sufficient to predict the average concentrations of these pollutants at street level, and also reflects their daily variations well, i.e. CO presents the similar double peaks as the traffic flow, PM₁₀ concentration is influenced by other sources. Meanwhile, the model predicts O₃ to stay less during the daytime and ascend in the night, just opposite to NO₂, which reveals the impact of photochemical reactions. In addition, the predicted concentrations on the windward side often exceed the leeward side, indicating the impact of the special street shape, as well as the wind.The comparison between the predicted street concentrations before and during the Olympic traffic control period shows that the overall on-road air quality was improved effectively, due to the 32.3% traffic flow reduction. The concentrations of PM₁₀, CO and NO₂ have reduced from 142.6 μg m⁻³, 3.02 mg m⁻³ and 118.7 μg m⁻³ to 102.0 μg m⁻³, 2.43 mg m⁻³ and 104.1 μg m⁻³. However, the different pollutants show diverse changes after the traffic control. PM₁₀ decreases most, and the reduction effect focusing on the first half-day even clears the morning peak, whereas CO and NO₂ have even reductions to minify the daily fluctuations on the whole. Opposite to the other pollutants, ozone shows an increase of concentration. The average reduction rate of PM₁₀, CO, NO₂ and O₃ are respectively 28%, 19.3%, 12.3% and −25.2%. Furthermore, the streets in east, west, south and north areas present different air quality improvements, probably induced by the varied background pollution in different regions around Beijing, along with the impact of wind force. This finding suggests the pollution control in the surrounding regions, not only in the urban area.     

Assessment of natural components of PM10 at UK urban and rural sites

Proposals from the European Commission have raised the possibility that Member States may be able to subtract the concentrations of natural components of airborne particulate matter from measured concentrations when evaluating compliance with EU Limit Values. By applying the pragmatic mass closure model [Harrison et al., 2003. A pragmatic mass closure model for airborne particulate matter at urban background and roadside sites. Atmospheric Environment 37, 4927–4933] to chemical composition data for PM₁₀, it has been possible to estimate the concentrations of natural sea salt, strongly bound water and secondary organic carbon (which is assumed wholly biogenic) to the measured mass of PM₁₀. Because of the difficulty in distinguishing between natural and anthropogenic crustal dusts, the contribution of natural windblown dust and soil has not been accounted for. When the natural components are estimated for two urban and one rural site in the UK, the long-term mean PM₁₀ concentration is reduced by between 5.2 and 7.3 μg m⁻³. The number of exceedences of the 50 μg m⁻³ 24-h limit value falls dramatically from 54 to 21 (from a total of 291 days) at an urban street canyon site, 7 to 3 (n=292 days) at an urban background site and from 8 to 0 (n=241 days) at a rural site when using gravimetric PM₁₀ concentrations. The calculations have also been performed using PM₁₀ concentrations measured by TEOM increased by a factor of 1.3 as recommended by the European Commission as an interim means of estimating gravimetric equivalency, and the number of exceedences of the 24-h limit value fell from 92 to 47 (from a total of 291 days) at the urban street canyon site, from 11 to 3 (n=292 days) at the urban background site and from 6 to 3 (n=241) at the rural site. Clearly, therefore, application of this proposed measure would make a very major difference to the likelihood of compliance or otherwise with the 24-h limit value for PM₁₀.     

Chemical composition of fine particles from incense burning in a large environmental chamber

 This study is aimed to characterize the major chemical compositions of PM_2.5 from incense burning in a large environmental chamber. Chemical analyses, including X-ray fluorescence for elemental species, ion chromatography for water soluble inorganic species (chloride, nitrate, sulfate, sodium, potassium, ammonium) and thermal/optical reflectance analysis for carbon species were carried out for combustion of three incense categories (traditional, aromatic and church incense). The average concentrations from incense burning ranged from 139.8 to 4414.7 μg m⁻³ for organic carbon (OC), and from 22.8 to 74.0 μg m⁻³ for elemental carbon (EC), respectively. The average OC and EC concentrations in PM_2.5 of three incense categories were in the order of church incense>traditional incense>aromatic incense. OC/EC ratios ranged from 7.0 to 39.1 for the traditional incense, with an average of 21.7; from 3.2 to 11.9 for the aromatic incense, with an average of 7.7. The concentrations of Cl⁻, SO₄²⁻, Na⁺ and K⁺ were highly variable. On average, the inorganic ion concentration sequence was traditional incense>church incense>aromatic incense. The profiles for elements were dominated by Na, Cl and K. In general, the major components in PM_2.5 fraction from incense burning are OC (especially OC2, OC3 and OC4), EC and K.     

The impacts of different kinds of dust events on PM10 pollution in northern China

In this study the frequencies of PM₁₀ (as key urban pollutant) in 14 key environmental protection cities in northern China were analyzed. It follows that the PM₁₀ concentration in the high-frequency period is higher with an extent 0.009–0.066 mg m⁻³ than in the low-frequency period of 2001–2002. Further the impacts of three kinds of dust events on the PM₁₀ concentration in four cities (Beijing, Hohhot, Xi’an and Lanzhou) were explored. The results showed that different kinds of dust events have different influences on variation of PM₁₀ concentration in these four cities. In Lanzhou and Hohhot, which are near the source areas of dust events, the contribution degree of these three dust events to the PM₁₀ is: floating dust>dust storm>blowing dust. Whereas, in Beijing and Xi’an situated in dust event passing areas, the mean value of PM₁₀ concentration is higher in blowing dust than in floating dust (no dust storm). In addition, the influences of dust events on PM₁₀ concentration are different in the cities on different dust event paths. In Beijing and Hohhot (on the northern path), the high PM₁₀ concentration is usually caused by blowing dust. But in both Lanzhou and Xi’an (on the western/northwestern path) the high PM₁₀ pollution concentration is usually caused by floating dust.     

Sources and processes affecting concentrations of PM10 and PM2.5 particulate matter in Birmingham (U.K.)

Hourly average concentrations of PM₁₀ and PM_2.5 have been measured simultaneously at a site within Birmingham U.K. between October 1994 and October 1995. Comparison of PM₁₀ and NO_x data with two other sites in the same city shows comparable summer and winter mean concentrations and highly significant inter-site correlations for both hourly and daily mean data. Over a four-month period samples were also collected for chemical analysis of sulphate, nitrate, chloride, ammonium and elemental and organic carbon. Analysis of the data indicates a marked difference between summer and winter periods. In the winter months PM_2.5 comprises about 80% of PM₁₀ and is strongly correlated with NO_x indicating the importance of road traffic as a source. In the summer months, coarse particles (PM₁₀−PM_2.5) account for almost 50% of PM₁₀ and the influence of resuspended surface dusts and soils and of secondary particulate matter is evident. The chemical analysis data are also consistent with three sources dominating the PM₁₀ composition: vehicle exhaust emissions, secondary ammonium salts and resuspended surface dusts. Coarse particles from resuspension showed a positive dependence on windspeed, whilst elemental carbon derived from road traffic exhibited a negative dependence.     

Estimation and validation of PM2.5/PM10 exhaust and non-exhaust emission factors for practical street pollution modelling

In order to carry out efficient traffic and air quality management, validated models and PM emission estimates are needed. This paper compares current available emission factor estimates for PM₁₀ and PM_2.5 from emission databases and different emission models, and validates these against eight high quality street pollution measurements in Denmark, Sweden, Germany, Finland and Austria.The data sets show large variation of the PM concentration and emission factors with season and with location. Consistently at all roads the PM₁₀ and PM_2.5 emission factors are lower in the summer month than the rest of the year. For example, PM₁₀ emission factors are in average 5–45% lower during the month 6–10 compared to the annual average.The range of observed total emission factors (including non-exhaust emissions) for the different sites during summer conditions are 80–130 mg km⁻¹ for PM₁₀, 30–60 mg km⁻¹ for PM_2.5 and 20–50 mg km⁻¹ for the exhaust emissions.We present two different strategies regarding modelling of PM emissions: (1) For Nordic conditions with strong seasonal variations due to studded tyres and the use of sand/salt as anti-skid treatment a time varying emission model is needed. An empirical model accounting for these Nordic conditions was previously developed in Sweden. (2) For other roads with a less pronounced seasonal variation (e.g. in Denmark, Germany, Austria) methods using a constant emission factor maybe appropriate. Two models are presented here.Further, we apply the different emission models to data sets outside the original countries. For example, we apply the “Swedish” model for two streets without studded tyre usage and the “German” model for Nordic data sets. The “Swedish” empirical model performs best for streets with studded tyre use, but was not able to improve the correlation versus measurements in comparison to using constant emission factors for the Danish side. The “German” method performed well for the streets without clear seasonal variation and reproduces the summer conditions for streets with pronounced seasonal variation. However, the seasonal variation of PM emission factors can be important even for countries not using studded tyres, e.g. in areas with cold weather and snow events using sand and de-icing materials. Here a constant emission factor probably will under-estimate the 90-percentiles and therefore a time varying emission model need to be used or developed for such areas.All emission factor models consistently indicate that a large part (about 50–85% depending on the location) of the total PM₁₀ emissions originates from non-exhaust emissions. This implies that reduction measures for the exhaust part of the vehicle emissions will only have a limited effect on ambient PM₁₀ levels.     

PM composition and source reconciliation in Mexico City

PM_2.5 and PM₁₀ were collected during 24-h sampling intervals from March 1st to 31st, 2006 during the MILAGRO campaign carried out in Mexico City's northern region, in order to determine their chemical composition, oxidative activity and the estimation of the source contributions during the sampling period by means of the chemical mass balance (CMB) receptor model. PM_2.5 concentrations ranged from 32 to 70 μg m⁻³ while that of PM10 did so from 51 to 132 μg m⁻³. The most abundant chemical species for both PM fractions were: OC, EC, SO₄²⁻, NO₃⁻, NH₄⁺, Si, Fe and Ca. The majority of the PM mass was comprised of carbon, up to about 52% and 30% of the PM2.5 and PM10, respectively. PM2.5 constituted more than 50% of PM10. The redox activity, assessed by the dithiothreitol (DTT) assay, was greater for PM_2.5 than for PM₁₀, and did not display significant differences during the sampling period. The PM_2.5 source reconciliation showed that in average, vehicle exhaust emissions were its most important source in an urban site with a 42% contribution, followed by re-suspended dust with 26%, secondary inorganic aerosols with 11%, and industrial emissions and food cooking with 10% each. These results had a good agreement with the Emission Inventory. In average, the greater mass concentration occurred during O₃S that corresponds to a wind shift initially with transport to the South but moving back to the North. Taken together these results show that PM chemical composition, oxidative potential, and source contribution is influenced by the meteorological conditions.     

Particulate matter emissions from on-road vehicles in a freeway tunnel study

Particulate matter, including coarse particles (PM_2.5–10, aerodynamic diameter of particle between 2.5 and 10 μm) and fine particles (PM_2.5, aerodynamic diameter of particle lower than 2.5 μm) and their compositions, including elemental carbon, organic carbon, and 11 water-soluble ionic species, and elements, were measured in a tunnel study. A comparison of the six-hour average of light-duty vehicle (LDV) flow of the two sampling periods showed that the peak hours over the weekend were higher than those on weekdays. However, the flow of heavy-duty vehicles (HDVs) on the weekdays was significant higher than that during the weekend in this study. EC and OC content were 49% for PM_2.5–10 and 47% for PM_2.5 in the tunnel center. EC content was higher than OC content in PM_2.5–10, but EC was about 2.3 times OC for PM_2.5. Sulfate, nitrate, ammonium were the main species for PM_2.5–10 and PM_2.5. The element contents of Na, Al, Ca, Fe and K were over 0.8 μg m^?3 in PM_2.5–10 and PM_2.5. In addition, the concentrations of S, Ba, Pb, and Zn were higher than 0.1 μg m^?3 for PM_2.5–10 and PM_2.5. The emission factors of PM_2.5–10 and PM_2.5 were 18 ± 6.5 and 39 ± 11 mg km^?1-vehicle, respectively. The emission factors of EC/OC were 3.6/2.7 mg km^?1-vehicle for PM_2.5–10 and 15/4.7 mg km^?1-vehicle for PM_2.5 Furthermore, the emission factors of water-soluble ions were 0.028(Mg²⁺)–0.81(SO₄^2?) and 0.027(NO₂^?)–0.97(SO₄^2?) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively. Elemental emission factors were 0.003(V)–1.6(Fe) and 0.001(Cd)–1.05(Na) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively.     

Study of lead phytoavailability for atmospheric industrial micronic and sub-micronic particles in relation with lead speciation

Particles from channelled emissions of a battery recycling facility were size-segregated and investigated to correlate their speciation and morphology with their transfer towards lettuce. Microculture experiments carried out with various calcareous soils spiked with micronic and sub-micronic particles (1650 ± 20 mg Pb kg⁻¹) highlighted a greater transfer in soils mixed with the finest particles. According to XRD and Raman spectroscopy results, the two fractions presented differences in the amount of minor lead compounds like carbonates, but their speciation was quite similar, in decreasing order of abundance: PbS, PbSO₄, PbSO₄·PbO, α-PbO and Pb⁰. Morphology investigations revealed that PM_2.5 (i.e. Particulate Matter 2.5 composed of particles suspended in air with aerodynamic diameters of 2.5 μm or less) contained many Pb nanoballs and nanocrystals which could influence lead availability. The soil-plant transfer of lead was mainly influenced by size and was very well estimated by 0.01 M CaCl₂ extraction.     

PM10 emission factors for non-exhaust particles generated by road traffic in an urban street canyon and along a freeway in Switzerland

Recent studies have shown clear contributions of non-exhaust emissions to the traffic related PM10 load of the ambient air. These emissions consist of particles produced by abrasion from brakes, road wear, tire wear, as well as vehicle induced resuspension of deposited road dust. The main scope of the presented work was to identify and quantify the non-exhaust fraction of traffic related PM10 for two roadside locations in Switzerland with different traffic regimes. The two investigated locations, an urban street canyon with heavily congested traffic and an interurban freeway, are considered as being typical for Central Europe. Mass-relevant contributions from abrasion particles and resuspended road dust mainly originated from particles in the size range 1–10 μm. The results showed a major influence of vehicle induced resuspension of road dust. In the street canyon, the traffic related PM10 emissions (LDV: 24 ± 8 mg km^?1 vehicle^?1, HDV: 498 ± 86 mg km^?1 vehicle^?1) were assigned to 21% brake wear, 38% resuspended road dust and 41% exhaust emissions. Along the freeway (LDV: 50 ± 13 mg km^?1 vehicle^?1, HDV: 288 ± 72 mg km^?1 vehicle^?1), respective contributions were 3% brake wear, 56% resuspended road dust and 41% exhaust emissions. There was no indication for relevant contributions from tire wear and abrasion from undamaged pavements.     

Polychlorinated dibenzo-p-dioxin and dibenzofuran in urban air of an Andean city

Particle-bound polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in ambient air were monitored together with particulate matter less than 10 μm (PM₁₀) at three sampling sites of the Andean city of Manizales, Colombia; during September 2009 and July 2010. PCDD/Fs ambient air emissions ranged from 1 fg WHO-TEQ m⁻³ to 52 fg WHO-TEQ m⁻³ in particulate fraction. The PM₁₀ concentrations ranged from 23 μg m⁻³ to 54 μg m⁻³. Concentrations of PM₁₀ and PCDD/Fs in ambient air observed for Manizales - a medium sized city with a population of 380 000 - were comparable to concentrations in larger cities. The highest concentrations of PCDD/Fs and PM₁₀ found in this study were determined at the central zone of the city, characterized by public transportation density, where diesel as principal fuel is used. In addition, hypothetical gas fractions of PCDD/Fs were calculated from theoretical K_p data. Congener profiles of PCDD/Fs exhibited ratios associated with different combustion sources at the different sampling locations, ranging from steel recycling to gasoline and diesel engines. Taking into account particle and gas hypothetical fraction of PCDD/Fs, Manizales exhibited values of PCDD/Fs equivalent to rural and urban-industrial sites in the southeast and center of the city respectively. Poor correlation of PCDDs with PM₁₀ (r = −0.55 and r = 0.52) suggests ambient air PCDDs were derived from various combustion sources. Stronger correlation was observed of PCDFs with PM₁₀. Poor correlation between precipitation and reduced PM₁₀ concentration in ambient air (r = −0.45) suggested low PM₁₀ removal by rainfall.     

Phytoremediation potential of the novel atrazine tolerant Lolium multiflorum and studies on the mechanisms involved

Atrazine impact on human health and the environment have been extensively studied. Phytoremediation emerged as a low cost, environmental friendly biotechnological solution for atrazine pollution in soil and water. In vitro atrazine tolerance assays were performed and Lolium multiflorum was found as a novel tolerant species, able to germinate and grow in the presence of 1 mg kg⁻¹ of the herbicide. L. multiflorum presented 20% higher atrazine removal capacity than the natural attenuation, with high initial degradation rate in microcosms. The mechanisms involved in atrazine tolerance such as mutation in psbA gene, enzymatic detoxification via P₄₅₀ or chemical hydrolysis through benzoxazinones were evaluated. It was demonstrated that atrazine tolerance is conferred by enhanced enzymatic detoxification via P₄₅₀. Due to its atrazine degradation capacity in soil and its agronomical properties, L. multiflorum is a candidate for designing phytoremediation strategies for atrazine contaminated agricultural soils, especially those involving run-off avoiding.     

Particle size distribution of airborne Aspergillus fumigatus spores emitted from compost using membrane filtration

Information on the particle size distribution of bioaerosols emitted from open air composting operations is valuable in evaluating potential health impacts and is a requirement for improved dispersion simulation modelling. The membrane filter method was used to study the particle size distribution of Aspergillus fumigatus spores in air 50 m downwind of a green waste compost screening operation at a commercial facility. The highest concentrations (approximately 8 × 10⁴ CFU m⁻³) of culturable spores were found on filters with pore diameters in the range 1–2 μm which suggests that the majority of spores are emitted as single cells. The findings were compared to published data collected using an Andersen sampler. Results were significantly correlated (p < 0.01) indicating that the two methods are directly comparable across all particles sizes for Aspergillus spores.     

Exposure of acid aerosol for schoolchildren in metropolitan Taipei

Metropolitan Taipei, which is located in the subtropical area, is characterized by high population and automobile densities. For convenience, most primary schools are located near major roads. This study explores the exposure of acid aerosols for schoolchildren in areas in Taipei with different traffic densities. Acid aerosols were collected by using a honeycomb denuder filter pack sampling system (HDS). Experimental results indicated that the air pollutants were significantly correlated with traffic densities. The ambient air NO₂, SO₂, HNO₃, NO₃⁻, SO₄²⁻, and aerosol acidity concentrations were 31.3 ppb, 4.7 ppb, 1.3 ppb, 1.9 μg m⁻³, 18.5 μg m⁻³, and 49.5 nmol m⁻³ in high traffic density areas, and 6.1 ppb, 1.8 ppb, 0.9 ppb, 0.7 μg m⁻³, 8.8 μg m⁻³ and 14.7 nmol m⁻³ in low traffic density areas. The exposure levels of acid aerosols for schoolchildren would be higher than the measurements because the sampling height was 5 m above the ground. The SO₂ levels were low (0.13–8.03 ppb) in the metropolitan Taipei. However, the SO₄²⁻ concentrations were relatively high, and might be attributed to natural emissions of sulfur-rich geothermal sources. The seasonal variations of acid aerosol concentrations were also observed. The high levels of acidic particles in spring time may be attributed to the Asian dust storm and low height of the mixture layer. We conclude that automobile contributed not only the primary pollutants but also the secondary acid aerosols through the photochemical reaction. Schoolchildren were exposed to twice the acid aerosol concentrations in high traffic density areas compared to those in low traffic density areas. The incidence of allergic rhinitis of schoolchildren in the high traffic density areas was the highest in spring time. Accompanied by high temperature variation and high levels of air pollution in spring, the health risk of schoolchildren had been observed.     

Acute and chronic effects of nano- and non-nano-scale TiO2 and ZnO particles on mobility and reproduction of the freshwater invertebrate Daphnia magna

Among the emerging literature addressing the biological effects of nanoparticles, very little information exists, particularly on aquatic organisms, that evaluates nanoparticles in comparison to non-nanocounterparts. Therefore, the potential effects of nano-scale and non-nano-scale TiO₂ and ZnO on the water flea, Daphnia magna, were examined in 48-h acute toxicity tests using three different test media, several pigment formulations – including coated nanoparticles – and a variety of preparation steps. In addition, a 21-d chronic Daphnia reproduction study was performed using coated TiO₂ nanoparticles. Analytical ultracentrifugation analyses provided evidence that the nanoparticles were present in a wide range of differently sized aggregates in the tested dispersions. While no pronounced effects on D. magna were observed for nano-scale and non-nano-scale TiO₂ pigments in 19 of 25 acute (48-h) toxicity tests (EC50 > 100 mg L⁻¹), six acute tests with both nano- and non-nano-scale TiO₂ pigments showed slight effects (EC10, 0.5–91.2 mg L⁻¹). For the nano-scale and non-nano-scale ZnO pigments, the acute 48-h EC50 values were close to the 1 mg L⁻¹ level, which is within the reported range of zinc toxicity to Daphnia. In general, the toxicity in the acute tests was independent of particle size (non-nano-scale or nano-scale), coating of particles, aggregation of particles, the type of medium or the applied pre-treatment of the test dispersions. The chronic Daphnia test with coated TiO₂ nanoparticles demonstrated that reproduction was a more sensitive endpoint than adult mortality. After 21 d, the NOEC for adult mortality was 30 mg L⁻¹ and the NOEC for offspring production was 3 mg L⁻¹. The 21-d EC10 and EC50 values for reproductive effects were 5 and 26.6 mg L⁻¹, respectively. This study demonstrates the utility of evaluating nanoparticle effects relative to non-nano-scale counterparts and presents the first report of chronic exposure to TiO₂ nanoparticles in D. magna.     

Effects of field-applied composted cattle manure and chemical fertilizer on ammonia and particulate ammonium exchanges at an upland field

The present study aimed to investigate the NH₃ volatilization loss from field-applied compost and chemical fertilizer and evaluate the atmosphere–land exchange of NH₃ and particulate NH₄⁺ (pNH₄) at an upland field with volcanic ash soil (Andosol) in Hokkaido, northern Japan. Two-step basal fertilization was conducted on the bare soil surface. First, a moderately fermented compost of cattle manure was applied by surface incorporation (mixing depth, 0–15 cm) at a rate of 117 kg N ha⁻¹ as total nitrogen (T-N) corresponding to 9.9 kg N ha⁻¹ as ammoniacal nitrogen (NH₄–N). Twelve days later, a chemical fertilizer containing 10% (w/w) of NH₄–N as a mixture of ammonium sulfate and ammonium phosphates was applied by row placement (cover depth, 3 cm) at a rate of 100 kg N ha⁻¹ as NH₄–N. The study period was divided into the first-half, beginning after the compost application (CCM period), and the second-half, beginning after the chemical fertilizer application (CF period). The mean air concentrations of NH₃ and pNH₄ (1.5 m height) were 7.6 and 3.0 μg N m⁻³, respectively, in the CCM period; the values were 3.7 and 3.9 μg N m⁻³, respectively, in the CF period. The composition ratios of NH₃ to the sum of NH₃ and pNH₄ (1.5 m height) were 72% and 49% in the CCM and CF periods, respectively. The NH₃ volatilization loss from the compost was 0.8% of the applied T-N (or 9.3% of the applied NH₄–N) and that from the chemical fertilizer was near zero. Excluding the period immediately after the compost application, the upland field acted as a net sink for NH₃ and pNH₄.     

Rates of particulate pollution deposition onto leaf surfaces: Temporal and inter-species magnetic analyses

Evaluation of health impacts arising from inhalation of pollutant particles <10 μm (PM₁₀) is an active research area. However, lack of exposure data at high spatial resolution impedes identification of causal associations between exposure and illness. Biomagnetic monitoring of PM₁₀ deposited on tree leaves may provide a means of obtaining exposure data at high spatial resolution. To calculate ambient PM₁₀ concentrations from leaf magnetic values, the relationship between the magnetic signal and total PM₁₀ mass must be quantified, and the exposure time (via magnetic deposition velocity (MV_d) calculations) known. Birches display higher MV_d (∼5 cm⁻¹) than lime trees (∼2 cm⁻¹). Leaf saturation remanence values reached ‘equilibrium’ with ambient PM₁₀ concentrations after ∼6 ‘dry’ days (<3 mm/day rainfall). Other co-located species displayed within-species consistency in MV_d; robust inter-calibration can thus be achieved, enabling magnetic PM₁₀ biomonitoring at unprecedented spatial resolution.