Law of variation for low density polyethylene dust explosion with different inert gases

To reveal the effects of different inert gases on explosion characteristics during low density polyethylene (LDPE) dust explosion and optimize the explosion-proof process, eight N₂ (CO₂)/air mixed inerting conditions were experimentally studied. Typical inerting conditions with 12 L cylindrical explosive tank were used to study the characteristics on the flame propagation. The thermogravimetric analysis with related theories were used to further explain the mechanism and quantities in low density polyethylene (LDPE) dust explosion with different inert gases. The results showed that the reduction of O₂ concentration could effectively delay the progress of flame growth process and weaken the effect of dust combustion reaction. The flame growth process of condition (N₂/air (18% O₂)) was 2.05 times slower than that of the non-inert condition. The explosion strength was obviously reduced, and the characteristic parameters such as explosion pressure and flame propagation speed were also affected by the decrease of O₂ concentration. For LDPE powder, the smaller the median diameter, the greater the explosion intensity and the lower the limiting oxygen content (LOC). The LOC with CO₂ was usually higher than that with N₂ and the effect of CO₂ was significantly better than N₂ in inerting.     

Synergistic inhibition of aluminum dust explosion by gas–solid inhibitors

The inhibition mechanism of gas-solid inhibitors on Al dust explosion was investigated experimentally in a closed cuboid chamber. The variation of parameters concerning flame propagation characteristic and explosion severity used to reflect the synergistic inhibition effect of gas-solid inhibitors on Al dust explosion were elucidated. The results showed that flame propagation velocity and explosion overpressure were inhibited with the increase of gas-solid inhibitors. The inhibition curves of gas-solid inhibitors within the experimental range were further obtained. The reason concerning the SEEP phenomenon was revealed through the GC-MS analysis. The combustion of ammonia enhanced the explosion overpressure when solid inhibitors performed at low concentration. The gas-phase product could be regarded as the inert gas as long as enough amount of inhibitors were added. To comprehend the inhibition mechanism of gas-solid inhibitors, X-ray diffraction was applied to figure out the crystal structure of explosion residue. The results indicated that both physical and chemical inhibition effects were imposed on Al dust explosion by gas-solid inhibitors, including endothermic decomposition, dilution of oxidizer, coverage of Al dust, and scavenger of free radicals. The results of this study will provide a scientific basis for the design of inhibition technology for the dust explosion.     

Study of the influence of melamine polyphosphate and aluminum hydroxide on the flame propagation and explosion overpressure of aluminum magnesium alloy dust

When aluminum magnesium alloy dust floats in the air, a certain ignition energy can easily cause an accidental explosion. To prevent and control the occurrence of accidental explosions and reduce the severity of accidents, it is necessary to carry out research on the explosion suppression of aluminum magnesium alloy dust. This paper uses a vertical glass tube experimental device and a 20 L spherical explosive experimental device to carry out experimental studies on the suppression of the flame propagation and explosion overpressure of aluminum magnesium alloy dust with melamine polyphosphate (MPP) and Al(OH)₃. With increasing MPP and Al(OH)₃ concentrations, the flame brightness darkened, the flame velocity and propagation distance gradually decreased, and P_max and (dp/dt)_max decreased significantly. When the amount of MPP added reached 60%, the flame propagation distance decreased to 188 mm, which is a decrease of 68%, and the explosion overpressure decreased to 0.014 MPa, effectively suppressing the explosion of aluminum magnesium alloy dust. The experimental results showed that MPP was more effective than Al(OH)₃ in inhibiting the flame propagation and explosion overpressure of the aluminum magnesium alloy dust. Finally, the inhibitory mechanisms of the MPP and Al(OH)₃ were further investigated. The MPP and Al(OH)₃ endothermic decomposition produced an inert gas, diluted the oxygen concentration and trapped active radicals to terminate the combustion chain reaction.     

Inerting effect of N2 on explosion of LDPE dust/ethylene hybrid mixtures

Explosion flame propagation characteristics and overpressure distribution of low density polyethylene (LDPE) dust and ethylene hybrid mixture were investigated under N₂ inerting conditions using a custom-designed 12 L cylindrical explosion tank. The results showed that a small amount of ethylene could promote the explosion characteristics of LDPE dust. N₂ inerting had different inhibitory effects on the explosion flame of LDPE dust and its mixture with ethylene. The explosion overpressure strength of the LDPE dust/ethylene hybrid mixture decreased with increasing N₂ concentration. The overall suppression effect of N₂ on the explosion overpressure of the LDPE dust was better than that of the LDPE dust/ethylene hybrid mixture explosion. As the ethylene concentration increased from 0% to 2.5%, the limiting oxygen concentration decreased by 13% oxygen. This small amount of ethylene restricted the traditional inerting process. The study conclusions can provide further scientific basis for the inerting and explosion proofing design of production process equipment involving LDPE dust.     

Inhibition effects of Al(OH)3 and Mg(OH)2 on Al-Mg alloy dust explosion

To identify a superior explosion suppressant for Al-Mg alloy dust explosion, the inhibition effects of Al(OH)₃ and Mg(OH)₂ powders on Al-Mg alloy explosion were investigated. A flame propagation suppression experiment was carried out using a modified Hartmann tube experimental system, an explosion pressure suppression experiment was carried out using a 20-L spherical explosion experimental system, and the suppression mechanisms of the two kinds of powders on Al-Mg alloy dust explosion were further investigated. The results demonstrate that by increasing the mass percentages of Al(OH)₃ and Mg(OH)₂, the flame height, flame propagation speed and explosion pressure of deflagration can be effectively reduced. When 80% Mg(OH)₂ powder was added, the explosion pressure was reduced to less than 0.1 MPa, and the explosion was restrained. Due to the strong polarity of the surface of Mg(OH)₂, agglomeration easily occurs; hence, when the added quantity is small, the inhibition effect is weaker than that of Al(OH)₃. Because the Mg(OH)₂ decomposition temperature is higher, the same quantity absorbs more heat and exhibits stronger adsorption of free radicals. Therefore, to fully suppress Al-Mg alloy explosion, the suppression effect of Mg(OH)₂ powder is better.     

超细CaCO3惰化剂对铝合金抛光伴生粉尘爆炸的防控效果*

为探究超细粉体惰化剂对铝合金抛光伴生粉尘爆炸特性的影响规律,利用标准化实验装置及自行搭建的实验平台,在对爆炸基本参数进行测试的基础上,分别研究超细CaCO3粉体对抛光废弃物粉尘点燃敏感度的钝化作用以及对爆炸火焰传播进程的惰化效果,并在相同条件下与同等粒径高纯度铝粉的实验效果进行比对。研究结果表明:铝合金抛光废弃物粉尘最小点火能量为280 mJ,而同等粒径高纯度铝粉最小点火能量为35 mJ;在铝合金抛光废弃物粉尘质量浓度为300 g/m3条件下,发生爆炸的火焰传播速度峰值为7.4 m/s,约为高纯度铝粉的57%,铝合金抛光废弃物粉尘的爆炸敏感度及猛烈度均低于高纯度铝粉;当超细CaCO3粉体的惰化比为30%时,可将铝合金抛光废弃物粉尘的最小点火能量钝化至约1 J,爆炸火焰失去持续传播能力,惰化作用效果充分显现。     

Inerting effect of CaCO3 powder on flame spread of wood dust layer

The effect of CaCO₃ powder, a typical inert dust, on the flame spread characteristics of wood dust layers was studied using an experimental device to understand the ignition characteristics of and develop inert explosion-proof technology for deposited wood dust. The results showed that the flame spread velocity (FSV) of the mixed dust layer was affected by the dispersion effect of CaCO₃ powder and physical heat absorption. As the CaCO₃ powder mass fraction increased, the FSV of the dust layer first increased and then decreased, reaching a peak at a 50% mass fraction. Moreover, the front-end temperature of the flame gradually decreased, and the red spark faded. The combustion reaction of the mixed dust layer could be more completed, and the colour of the combustion residue changed from charcoal black to charcoal grey. The coupling effect of the initial temperature and wind speed can promote an increase in the FSV in the mixed dust layer. The Gauss–Amp model of the FSV of the wood dust layer and mass fraction of CaCO₃ powder showed that the peak of the FSV occurred when the mass fraction of CaCO₃ powder was between 40 and 50%. Thus, a good inerting and explosion-proof effect can be achieved by using CaCO₃ powder with a mass fraction of more than 50%; it can improve the whole inerting process. Inert explosion-proof technology should be considered when assessing fire and explosion risk of dust in real process industry situations.     

Study on the deflagration reaction process of oil gas in long-narrow confined space based on PLIF and flame spectra

Oil gas explosion in long-narrow confined space is a typical unsteady combustion process. To study the reaction process, two experiment techniques are adopted in this research. One is planner laser induced fluorescence, which is used to achieve the transient measurement of free radicals in unsteady premixed combustion field. The other one is the spectral testing technique, which is used to measure the luminescence spectrum characteristics of oil gas combustion flame. The distribution of OH radical and CH radical at different positions in the combustion field, the common partition of deflagration flame structure under different oil gas concentrations, and the main luminescence spectra of radicals such as OH, CH, C₂, C₃, CO₂, H₂O and HCO are obtained. By comparing the above three aspects, the combustion reaction process of premixed mixture is revealed, driven by the coupling effect of chemical reaction and fluid flow in the process of explosion propagation. The process can be described briefly as follows. In the “outer flame zone”, large hydrocarbon molecules are mainly transformed to small molecules and free radicals by means of pyrolysis, dehydrogenation and oxidation. In the “inner flame zone”, carbon particles and combustion products produced and gathered after relevant reactions.     

Detailed analysis of flame propagation during dust explosions by UV band observations

It is important to sufficiently understand the phenomena during the dust explosions in order to take appropriate measures preventing dust explosion accidents. However, at present basic knowledge on flame propagation mechanisms during dust explosions is not enough. In this study, therefore, the flame propagation mechanisms during dust explosions are examined by detailed analyses using a special observation at UV band. Small scale experiments were performed to analyze flame propagating processes in detail. In the experiments, the stearic acid was used as the combustible particle, suspended particles were ignited by an electric spark, and flame propagation through the combustible dust was observed by using a special observation system at UV band. The leading combustion zone is observed to consist of discrete burning blue spot flames by the observation using ordinary photograph system. It is questionable how the leading flame of such discrete structure propagates. In this study, high-speed video images at UV band through a band-pass filter were taken to detect OH emission from combustion reaction zone. Using this method, the propagating flame could be detected clearly and the flame propagation mechanism could be examined in detail. In the conditions performed in this study, discrete flame propagation was not observed and the leading flame was observed to propagate continuously. This result is of importance for understanding the flame propagation phenomena during dust explosion.     

PAN dust explosion inhibition mechanisms of NaHCO3 and Al(OH)3

We investigate the PAN dust explosion inhibition behaviors of NaHCO₃ and Al(OH)₃ in a 20 L spherical explosion system and a transparent pipe explosion propagation test system. The results show that, in the standard 20 L spherical explosion system, the highest PAN dust explosion concentration is 500 g/m³, the maximum explosion pressure is 0.661 MPa, and the maximum explosion pressure increase rate is 31.64 MPa/s; adding 50% NaHCO₃ and 60% Al(OH)₃ can totally inhibit PAN dust explosion. In the DN0.15 m transparent pipe explosion propagation test system, for 500 g/m³ PAN dust, the initial explosion flame velocity is 102 m/s, the initial pressure is 0.46 MPa, and the initial temperature is 967 °C; adding 60% NaHCO₃ and 70% Al(OH)₃ can totally inhibit PAN dust explosion flames. Through FTIR and TG analyses, we obtain the explosion products and pyrolysis patterns of the explosion products of PAN dust, NaHCO₃, and Al(OH)₃. On this basis, we also summarize the PAN dust explosion inhibition mechanisms of NaHCO₃ and Al(OH)₃.     

R290制冷剂惰化燃爆特性实验研究

为了研究R290制冷剂惰化燃爆特性,采用带搅拌功能和氧浓度在线测定的20L球试验装置,对R290制冷剂进行了极限氧浓度测定。实验测定了丙烷在CO2和N2惰化气氛中的爆炸极限及极限空气浓度LAC,确定丙烷的极限氧浓度LOC;采用三元图爆炸区、丙烷-O2二维图爆炸区和ASTM标准分布图分析了混合气体爆炸区边界的燃爆特征,给出了极限氧浓度的确定方法和边界爆炸压力分布规律。实验结果表明:常温常压下R290的爆炸极限为2.1%～9.6%,CO2惰化气氛中的极限氧浓度为13.3%,对应的丙烷浓度为3.3%;N2惰化气氛中的极限氧浓度为10.8%,对应的丙烷浓度为2.7%。通过对比分析不同CO2和N2浓度下的爆炸区分布特征,表明CO2对丙烷的惰化效果要优于N2,以氮气和二氧化氮体积分数比为1∶2测试惰化气氛保护能力,惰化效果介于同浓度单种惰性气体之间。     

Inhibition effects of aluminum dust explosions by various kinds of ammonium polyphosphate

In this work, vinyltriethoxysilane (A151) and 3-aminopropyltriethoxysilane (KH550) were used to modify ammonium polyphosphate (APP), showing that the dispersibility of APP could be improved remarkably by A151 and KH550. The maximum explosion pressure of aluminum dust explosion decreased with the addition of APP, A151-APP (APP-A) and KH550-APP (APP-B), with the exception of the case where the inerting ratio (α) of APP-A was less than 0.4. After the addition of APP-B, there was little difference in flame propagation behavior and explosion pressure compared with that of adding APP, indicating that APP-B could retain the inhibition performance of APP compared with APP-A. When the inerting ratios of APP, APP-A and APP-B were 1.2, 1.4 and 1.4, respectively, the aluminum dust explosion could be completely inhibited. The explosion residues of aluminum dust/APP mainly consisted of Al₂O₃, P-containing and N-containing compounds. It could be analyzed that APP exerted the inhibition effect through both chemical and physical effects.     

Effect of flame propagation regime on pressure evolution of nano and micron PMMA dust explosions

Experiments using an open space dust explosion apparatus and a standard 20 L explosion apparatus on nano and micron polymethyl methacrylate dust explosions were conducted to reveal the differences in flame and pressure evolutions. Then the effect of combustion and flame propagation regimes on the explosion overpressure characteristics was discussed. The results showed that the flame propagation behavior, flame temperature distribution and ion current distribution all demonstrated the different flame structures for nano and micron dust explosions. The combustion and flame propagation of 100 nm and 30 μm PMMA dust clouds were mainly controlled by the heat transfer efficiency between the particles and external heat sources. Compared with the cluster diffusion dominant combustion of 30 μm dust flame, the premixed-gas dominant combustion of 100 nm dust flame determined a quicker pyrolysis and combustion reaction rate, a faster flame propagation velocity, a stronger combustion reaction intensity, a quicker heat release rate and a higher amount of released reaction heat, which resulted in an earlier pressure rise, a larger maximum overpressure and a higher explosion hazard class. The complex combustion and propagation regime of agglomerated particles strongly influenced the nano flame propagation and explosion pressure evolution characteristics, and limited the maximum overpressure.     

Experiment-based investigations of magnesium dust explosion characteristics

An experimental investigation was carried out on magnesium dust explosions. Tests of explosion severity, flammability limit and solid inerting were conducted thanks to the Siwek 20 L vessel and influences of dust concentration, particle size, ignition energy, initial pressure and added inertant were taken into account. That magnesium dust is more of an explosion hazard than coal dust is confirmed and quantified by contrastive investigation. The Chinese procedure GB/T 16425 is overly conservative for LEL determination while EN 14034-3 yields realistic LEL data. It is also suggested that 2000-5000 J is the most appropriate ignition energy to use in the LEL determination of magnesium dusts, using the 20 L vessel. It is essential to point out that the overdriving phenomenon usually occurs for carbonaceous and less volatile metal materials is not notable for magnesium dusts. Trends of faster burning velocity and more efficient and adiabatic flame propagation are associated with fuel-rich dust clouds, smaller particles and hyperbaric conditions. Moreover, Inerting effectiveness of CaCO₃ appears to be higher than KCl values on thermodynamics, whereas KCl represents higher effectiveness upon kinetics. Finer inertant shows better inerting effectiveness.     

Effects of multiple annular obstacles on flame propagation of local corn starch dust in a vertical pipe

With high-speed camera technology, the propagation behavior of explosion flame for the local dust cloud of corn starch in a semi-open vertical pipe under the action of the annular obstacle was studied experimentally, and the blockage rate and the annular obstacle numbers as well as impact of dust cloud concentration on the flame propagation were investigated. The researches showed that both the blockage rate and the annular obstacle numbers have significant effects on the flame speed and propagation process for the dust cloud explosion of corn starch. The increase of the blockage rate of such annular obstacles will cause that the combustion of dust cloud with high concentration is mainly concentrated in the lower part of the pipe. The increase of the annular obstacle numbers will lead to the acceleration of combustion of the dust cloud. With the increase of the blockage rate and the annular obstacle numbers, the maximum flame speed shows a trend of the first increasing and then decreasing, and the phenomenon of accelerated propagation of the flame becomes more and more obvious, however, the distance of continuous acceleration for the flame is gradually decreased and the maximum flame speed is farther from the outlet of the pipe. Under the action of such annular obstacles, the concentration of dust cloud has a significant effect on the flame speed and shape of the dust cloud of the corn starch. The increase of the concentration of the dust cloud will decrease the acceleration effect of such annular obstacles to result in maximum flame speed showing a trend of the first increasing and then decreasing. However, the acceleration distance of the flame is longer, and the maximum flame speed is closer to the outlet of the pipe. The increasing concentration will make the flame speed develop more slowly, the flame color will be darker, and the flame segmentation phenomenon will be more obvious.     

外部条件对玉米淀粉粉尘爆炸特性的影响

为了探明外部条件对玉米淀粉粉尘爆炸特性参数的影响,利用20 L球形爆炸装置进行试验测试,探讨了点火能量及粉尘含水量对粉尘爆炸特性的影响,对比研究了CaCO_3和Al(OH)_3两种惰性介质的抑爆效果。结果表明:随点火能量增加,粉尘最大爆炸压力和最大升压速率呈线性上升,在高质量浓度下,粉尘爆炸压力受点火能量的影响更显著;添加CaCO_3和Al(OH)_3能够降低玉米淀粉的爆炸压力,相对于CaCO_3的物理抑爆,Al(OH)_3的物理-化学抑爆效果更佳;玉米淀粉粉尘的最大爆炸压力及爆炸升压速率随粉尘含水量降低而不断增大。     

Flame propagation behaviors of nano- and micro-scale PMMA dust explosions

Flame propagation behaviors of nano- and micro-polymethyl methacrylate (PMMA) dust explosions were experimentally studied in the open-space dust explosion apparatus. High-speed photography with normal and microscopic lenses were used to record the particle combustion behaviors and flame microstructures. Simple physical models were developed to explore the flame propagation mechanisms. High-speed photographs showed two distinct flame propagation behaviors of nano- and micro-PMMA dust explosions. For nano-particles, flame was characterized by a regular spherical shape and spatially continuous combustion structure combined with a number of luminous spot flames. The flame propagation mechanism was similar to that of a premixed gas flame coupled with solid surface combustion of the agglomerates. In comparison, for micro-particles, flame was characterized by clusters of flames and the irregular flame front, which was inferred to be composed of the diffusion flame accompanying the local premixed flame. It was indicated that smaller particles maintained the leading part of the propagating flame and governed the combustion process of PMMA dust clouds. Increasing the mass densities from 105 g/m³ to 217 g/m³ for 100 nm PMMA particles, and from 72 g/m³ to 170 g/m³ for 30 μm PMMA particles, the flame luminous intensity, scale and the average propagation velocity were enhanced. Besides, the flame front became more irregular for 30 μm PMMA dust clouds.     

Explosion prevention and weighting analysis on the inerting effect of methane via grey entropy model

Explosion prevention is vital for process safety and daily life. In practice, inerting is viewed as an ideal method to reach basic explosion prevention as well as to diminish flammability risk in normal operation, storage, and transportation of materials. This study deals with the inerting effect on the explosion range for methane via grey entropy model, comparatively detected under the different inert gases of nitrogen (N₂), argon (Ar), and carbon dioxide (CO₂), which have various loading inerting concentrations: 10 (90 vol% air), 20 (80 vol% air) and 25 vol% (75 vol% air). The inert influences were determined via the experimental 20-L-apparatus investigations under 1 atm, 30 ^OC, combined with the grey entropy model, which is one of the most prevailingly used grey system theories for weighting analysis and decision-making of the fire and explosion assessment for practical operations. The results indicated that CO₂ had better inerting capacity than the others, as derived from our grey entropy theoretical soft computing calculations. Through the combination of the grey entropy weighting analysis model and the flammability investigations in this study, the concluded decision-making was feasible and useful for the practical applications of inert gases for preventing fire and explosion hazards in relevant processes.     

Experimental investigation on explosion flame propagation of wood dust in a semi-closed tube

In order to explore flame propagation characteristics during wood dust explosions in a semi-closed tube, a high-speed camera, a thermal infrared imaging device and a pressure sensor were used in the study. Poplar dusts with different particle size distributions (0–50, 50–96 and 96–180 μm) were respectively placed in a Hartmann tube to mimic dust cloud explosions, and flame propagation behaviors such as flame propagation velocity, flame temperature and explosion pressure were detected and analyzed. According to the changes of flame shapes, flame propagations in wood dust explosions were divided into three stages including ignition, vertical propagation and free diffusion. Flame propagations for the two smaller particles were dominated by homogeneous combustion, while flame propagation for the largest particles was controlled by heterogeneous combustion, which had been confirmed by individual Damköhler number. All flame propagation velocities for different groups of wood particles in dust explosions were increased at first and then decreased with the augmentation of mass concentration. Flame temperatures and explosion pressures were almost similarly changed. Dust explosions in 50–96 μm wood particles were more intense than in the other two particles, of which the most severe explosion appeared at a mass concentration of 750 g/m³. Meanwhile, flame propagation velocity, flame propagation temperature and explosion pressure reached to the maximum values of 10.45 m/s, 1373 °C and 0.41 MPa. In addition, sensitive concentrations corresponding to the three groups of particles from small to large were 500, 750 and 1000 g/m³, separately, indicating that sensitive concentration in dust explosions of wood particles was elevated with the increase of particle size. Taken together, the finding demonstrated that particle size and mass concentration of wood dusts affected the occurrence and severity of dust explosions, which could provide guidance and reference for the identification, assessment and industrial safety management of wood dust explosions.     

Effect of Al2O3 particle size reduction on aluminium dust explosion

To investigate the effect of Al₂O₃ particle size on an aluminum explosion, the overpressure and flame velocity in a vertical duct were evaluated. The results show that the inhibitory effect of submicron Al₂O₃ is best, while the inhibitory effect increases with increasing inerting ratio. However, the inhibitory effect of micron Al₂O₃ does not increase significantly after the inerting ratio exceeds 40%. For high-concentration aluminum powder, 0.8 μm Al₂O₃ with an inerting ratio less than 20% promotes aluminum explosion. As the inerting ratio increases beyond 20%, however, the overpressure decreases. Furthermore, Al₂O₃ inhibits the formation of the intermediate product AlO and decreases the flame brightness. As the inerting ratio of 0.8 μm Al₂O₃ reaches 50%, the white patches in the flame image disappear. The results of scanning electron microscopy showed that the explosion products agglomerate and some dot-like protrusions appear on the surface of the unburned aluminum particles. The inhibition mechanism was qualitatively investigated. Physical heat absorption is proven to play a limited role. Thermal radiation and chemical inhibition play a key role. The chemical effect mainly influences the surface reaction energy source.