Law of variation for low density polyethylene dust explosion with different inert gases

To reveal the effects of different inert gases on explosion characteristics during low density polyethylene (LDPE) dust explosion and optimize the explosion-proof process, eight N₂ (CO₂)/air mixed inerting conditions were experimentally studied. Typical inerting conditions with 12 L cylindrical explosive tank were used to study the characteristics on the flame propagation. The thermogravimetric analysis with related theories were used to further explain the mechanism and quantities in low density polyethylene (LDPE) dust explosion with different inert gases. The results showed that the reduction of O₂ concentration could effectively delay the progress of flame growth process and weaken the effect of dust combustion reaction. The flame growth process of condition (N₂/air (18% O₂)) was 2.05 times slower than that of the non-inert condition. The explosion strength was obviously reduced, and the characteristic parameters such as explosion pressure and flame propagation speed were also affected by the decrease of O₂ concentration. For LDPE powder, the smaller the median diameter, the greater the explosion intensity and the lower the limiting oxygen content (LOC). The LOC with CO₂ was usually higher than that with N₂ and the effect of CO₂ was significantly better than N₂ in inerting.     

Inerting characteristics of ultrafine Mg(OH)2 on starch dust explosion flame propagation

Experiments on the flame propagation of starch dust explosion with the participation of ultrafine Mg(OH)₂ in a vertical duct were conducted to reveal the inerting evolution of explosion processes. Combining the dynamic behaviors of flame propagation, the formation law of gaseous combustion products, and the heat dissipation features of solid inert particles, the inerting mechanism of explosion flame propagation is discussed. Results indicate that the ultrafine of Mg(OH)₂ powders can cause the agglomeration of suspended dust clouds, which makes the flame combustion reaction zone fragmented and forms multiple small flame regions. The flame reaction zone presents non-homogeneous insufficient combustion, which leads to the obstruction of the explosion flame propagation process and the obvious pulsation propagation phenomenon. As the proportion of ultrafine Mg(OH)₂ increases, flame speed, flame luminescence intensity, flame temperature and deflagration pressure all show different degrees of inerting behavior. The addition of ultrafine Mg(OH)₂ not only causes partial inerting on the explosion flame, but also the heat dissipation of solid inert particles affects the acceleration of its propagation. The explosion flame propagation is inhibited by the synergistic effect of inert gas-solid phase, which attenuates the risk of starch explosion. The gas-solid synergistic inerting mechanism of starch explosion flame propagation by ultrafine Mg(OH)₂ is further revealed.     

Study on explosion characters of HDPE dust inerted by CaCO3 and NaHCO3

To prevent high density polyethylene (HDPE) dust explosions, this study evaluated HDPE's explosive sensitivity characteristics, and comparatively examined two inert dust types (CaCO₃ and NaHCO₃) to mitigate the explosive sensitivity of HDPE dust. In the serials of experiments, the 1.2 L Hartmann tube and Godbert-Greenwald furnace were used respectively to measure the minimum ignition energy (MIE) and minimum ignition temperature (MIT) of HDPE dust. The findings demonstrated that the MIE and MIT of HDPE are 56.8 mJ and 320 °C under the most sensitive situation. Second, both CaCO₃ and NaHCO₃ can inhibit the explosive sensitivity of HDPE with the variation of several parameters (i.e., quality percentage and particle sizes). Specially, as the quality percentage of 38–48 μm NaHCO₃ come to 70%, the HDPE/NaHCO₃ will not be explosive. Finally, NaHCO₃ had a better inerting effect than CaCO₃ in the reduction of explosive sensitivity of HDPE.     

Inerting effect of N2 on explosion of LDPE dust/ethylene hybrid mixtures

Explosion flame propagation characteristics and overpressure distribution of low density polyethylene (LDPE) dust and ethylene hybrid mixture were investigated under N₂ inerting conditions using a custom-designed 12 L cylindrical explosion tank. The results showed that a small amount of ethylene could promote the explosion characteristics of LDPE dust. N₂ inerting had different inhibitory effects on the explosion flame of LDPE dust and its mixture with ethylene. The explosion overpressure strength of the LDPE dust/ethylene hybrid mixture decreased with increasing N₂ concentration. The overall suppression effect of N₂ on the explosion overpressure of the LDPE dust was better than that of the LDPE dust/ethylene hybrid mixture explosion. As the ethylene concentration increased from 0% to 2.5%, the limiting oxygen concentration decreased by 13% oxygen. This small amount of ethylene restricted the traditional inerting process. The study conclusions can provide further scientific basis for the inerting and explosion proofing design of production process equipment involving LDPE dust.     

Minimum ignition energies of pure magnesium powders due to electrostatic discharges and nitrogen's effect

This paper experimentally investigated the relation between the minimum ignition energy (MIE) of magnesium powders as well as the effect of inert nitrogen (N₂) on the MIE. The modified Hartmann vertical-tube apparatus and four kinds of different-sized pure magnesium powders (median particle size, D50; 28.1 μm–89.8 μm) were used in this study. The MIE of the most sensitive magnesium powder was 4 mJ, which was affected by the powder particle size (D50; 28.1 μm). The MIE of magnesium powder increased with an increase in the N₂ concentration for the inerting technique. The magnesium dust explosion with an electrostatic discharge of 1000 mJ was suppressed completely at an N₂ concentration range of more than 98%. The experimental data presented in this paper will be useful for preventing magnesium dust explosions generated from electrostatic discharges.     

Inhibiting effects by Fe2O3 on combustion and explosion characteristics of ABS resin

The global increase in the use of, and reliance on, plastics has prompted the demand for acrylonitrile-butadiene-styrene (ABS) resin in various fields. With this increased requirement, numerous failures have occurred in the ABS process. Those incidents, resulting from electrostatic discharge, powder accumulation, heat accumulation, construction sparks, and plant fires, have caused dust fire and explosions.In this study, the ABS resin was gleaned from the site and tested for its explosion parameters, including minimum ignition temperature of dust cloud (MIT_C), minimum ignition energy (MIE), and minimum explosion concentration (MEC). To improve loss prevention in the manufacturing process, ferric oxide (Fe₂O₃) as an inert additive was added in the ABS powder. According to the MIE test, Fe₂O₃ has an apparent inhibiting effect on dust explosion for the ABS dust. With the proportion of Fe₂O₃ increased from 25 to 50 mass% in ABS, the MIE increased from 67 to 540 mJ. The explosion tests via 20-L apparatus indicated that Fe₂O₃ mixed with ABS could not increase the MEC significantly. However, the explosion pressure dropped by increasing in the ratio of Fe₂O₃ in ABS. This inerting strategy of ABS was deemed to substantially lessen the probability and severity of fire and explosion.     

超细CaCO3惰化剂对铝合金抛光伴生粉尘爆炸的防控效果*

为探究超细粉体惰化剂对铝合金抛光伴生粉尘爆炸特性的影响规律,利用标准化实验装置及自行搭建的实验平台,在对爆炸基本参数进行测试的基础上,分别研究超细CaCO3粉体对抛光废弃物粉尘点燃敏感度的钝化作用以及对爆炸火焰传播进程的惰化效果,并在相同条件下与同等粒径高纯度铝粉的实验效果进行比对。研究结果表明:铝合金抛光废弃物粉尘最小点火能量为280 mJ,而同等粒径高纯度铝粉最小点火能量为35 mJ;在铝合金抛光废弃物粉尘质量浓度为300 g/m3条件下,发生爆炸的火焰传播速度峰值为7.4 m/s,约为高纯度铝粉的57%,铝合金抛光废弃物粉尘的爆炸敏感度及猛烈度均低于高纯度铝粉;当超细CaCO3粉体的惰化比为30%时,可将铝合金抛光废弃物粉尘的最小点火能量钝化至约1 J,爆炸火焰失去持续传播能力,惰化作用效果充分显现。     

Experimental investigation of the influence of inert solids on ignition sensitivity of organic powders

This work presents the results of the experimental characterization of the ignition sensitivity of solid inertant/combustible powders mixtures. Three inert solids (alumina, Kieselguhr, aerosil) and eleven organic powders have been considered and the following parameters have been determined: (1) the minimum ignition energy, (2) the minimum ignition temperature in cloud and (3) the minimum ignition temperature in 5 mm layer. The effects of the addition of inert solids are described and a simple model is proposed to represent the experimental results.Generally, increasing inert solid content in a powder leads to a higher minimum ignition energy as well as a higher minimum ignition temperatures in cloud and in layer. In some cases, the flammability is influenced above a threshold concentration value, which can be quite high (up to 85 wt.%). Indeed, the proposed model shows a zone below the minimum ignition concentration (MIC), which does not enable an efficient or safe inerting: either the admixed inert solid does not provide a sufficient effect, or it can even facilitate the ignition of the dust by notably improving its dispersability.The influence of key parameters such as the thermal conductivity or optical properties on the efficiency of the inerting by admixed solid need to be further assessed in a future work in view to better understand the mechanisms involved and to extend the scope to other types of oxidizable materials.     

Experimental study on ignitability of pure aluminum powders due to electrostatic discharges and Nitrogen's effect

In order to prevent dust explosions due to electrostatic discharges (ESD), this paper reports the minimum ignition energy (MIE) of aluminum powders in the air and the effective nitrogen (N₂) concentration for the inert technique. The Hartman vertical-tube apparatus and five kinds of different sized pure aluminum powders (median particle size, D50; 8.53 μm–51.2 μm) were used in this study. The statistic minimum ignition energy (MIE_s) of the most sensitive aluminum powder used in this study was 5 mJ, which was affected by the powder particle size (D50; 8.53 μm). In the case of aluminum powder, the inerting effects of N₂ were quite different from the polymer powders. The MIE of aluminum powder barely changed until the N₂ concentration was 89% in comparison with that of the normal air. When the N₂ concentration was 90%, the MIE of aluminum powders suddenly exceeded 1000 mJ, which does not occur easily with ESD in the industrial process.     

Effect of Al2O3 particle size reduction on aluminium dust explosion

To investigate the effect of Al₂O₃ particle size on an aluminum explosion, the overpressure and flame velocity in a vertical duct were evaluated. The results show that the inhibitory effect of submicron Al₂O₃ is best, while the inhibitory effect increases with increasing inerting ratio. However, the inhibitory effect of micron Al₂O₃ does not increase significantly after the inerting ratio exceeds 40%. For high-concentration aluminum powder, 0.8 μm Al₂O₃ with an inerting ratio less than 20% promotes aluminum explosion. As the inerting ratio increases beyond 20%, however, the overpressure decreases. Furthermore, Al₂O₃ inhibits the formation of the intermediate product AlO and decreases the flame brightness. As the inerting ratio of 0.8 μm Al₂O₃ reaches 50%, the white patches in the flame image disappear. The results of scanning electron microscopy showed that the explosion products agglomerate and some dot-like protrusions appear on the surface of the unburned aluminum particles. The inhibition mechanism was qualitatively investigated. Physical heat absorption is proven to play a limited role. Thermal radiation and chemical inhibition play a key role. The chemical effect mainly influences the surface reaction energy source.     

Experiment-based investigations of magnesium dust explosion characteristics

An experimental investigation was carried out on magnesium dust explosions. Tests of explosion severity, flammability limit and solid inerting were conducted thanks to the Siwek 20 L vessel and influences of dust concentration, particle size, ignition energy, initial pressure and added inertant were taken into account. That magnesium dust is more of an explosion hazard than coal dust is confirmed and quantified by contrastive investigation. The Chinese procedure GB/T 16425 is overly conservative for LEL determination while EN 14034-3 yields realistic LEL data. It is also suggested that 2000-5000 J is the most appropriate ignition energy to use in the LEL determination of magnesium dusts, using the 20 L vessel. It is essential to point out that the overdriving phenomenon usually occurs for carbonaceous and less volatile metal materials is not notable for magnesium dusts. Trends of faster burning velocity and more efficient and adiabatic flame propagation are associated with fuel-rich dust clouds, smaller particles and hyperbaric conditions. Moreover, Inerting effectiveness of CaCO₃ appears to be higher than KCl values on thermodynamics, whereas KCl represents higher effectiveness upon kinetics. Finer inertant shows better inerting effectiveness.     

Structure and flame speed of dilute and dense layered coal-dust explosions

Multidimensional time-dependent simulations were performed to study the interaction of a stoichiometric methane–air detonation with layers of coal dust. The simulations solved equations representing a Eulerian kinetic-theory-based granular multiphase model applicable to dense and dilute particle volume fractions. These equations were solved using a high-order Godunov-based method for compressible fluid dynamics. Two dust layer concentrations were considered: loose with an initial volume fraction of 1%, and dense with an initial volume fraction of 47%. Each layer was simulated with two types of dust: reactive coal and inert ash. Burning of the coal particles results in a coupled complex consisting of an accelerating shock leading a coal-dust flame. The overall structure of the shock–flame complex resembles that of a premixed fast flame with length scales on the order of several meters. The large length scales are direct results of time needed to lift, mix, heat, and autoignite the particle. The flame speeds are large and much larger than the gas-phase velocity. Large spikes of flame speed are characteristic of the 47% case. These spikes and high flame speed are caused by pockets of coal dust autoigniting ahead of the flame. The flame is choked in the 1% case due to the gas-phase products exceeding the sonic velocity with respect to the flame. The 47% case is choked due to attenuation of pressure waves as they propagate through particles. Inert layers of dust substantially reduce the overpressure, impulse, and speed produced by propagating blast wave. The results also show that loose layers of dust are far more dangerous than dense layers. The shock and flame are more strongly coupled for loose layers, propagate at higher velocity, and produce large overpressures and impulses.     

Inhibiting effect of inhibitors on ignition sensitivity of wood dust

Wood products are easy to produce dust in the production and processing process, and have a serious explosion risk. In order to improve the safety of wood products production, the inhibiting effects of magnesium hydroxide (MTH), SiO₂, melamine polyphosphate (MPP) on the minimum ignition energy (MIE) and minimum ignition temperature (MIT) of wood dust were experimentally studied. The results showed that the inhibiting effects of inhibitors on the MIE of wood dust show the order of MPP > SiO₂>MTH. The order of the inhibiting effects on the MIT of wood dust was MPP > MTH > SiO_2. When 10% MPP was added to wood dust, the time when the flame appears (T_appear) and the time when the flame reaches the top of the glass tube (T_top) obviously rose to 80, 140 ms. Therefore, MPP had the best inhibiting effect on the ignition sensitivity of wood dust.According to thermogravimetry (TG), differential scanning calorimetry (DSC) tests, the introduction of MPP leaded to lower maximum mass loss rate (MMLR), higher temperature corresponding to mass loss of 90% (T_0.1), residual mass and heat absorption. In addition, thermogravimetric analysis/infrared spectrometry (TG-IR) results showed that MPP produced H₂O (g) and NH₃ (g) during the thermal decomposition process, which diluted the oxygen.     

Minimum Ignition Temperature of layer and cloud dust mixtures

The prevention of dust explosions is still a challenge for the process industry. Ignition, in particular, is a phenomenon that is still not completely understood. As a consequence, safety conditions pertaining to ignition suppression are rarely identified to an adequate level. It is well known that, in general, the ignition attitude of a dust depends on several factors, such as the nature of the chemical, the particle size, moisture content, etc., but there is still a lack of knowledge on the effect of the single variables.This paper has the aim of providing data on the Minimum Ignition Temperatures of dust mixtures obtained from a mixing of a combustible dust (flour, lactose, sucrose, sulphur) and an inert dust (limestone, extinguishing powders) as well as from the mixing of two different combustible dusts. Various mixtures with different weight ratios have been tested in a Godbert Greenwald (GG) furnace and on a hot plate in order to measure the effect of mixture composition on the Minimum Ignition Temperature (MIT_L) of the layer and on the Minimum Ignition Temperature (MIT_C) of the cloud. In order to further verify the effects of inert dust particle size, inerts sieved to different size ranges have been tested separately. Generally, both MIT_L and MIT_C increase as the inert content is increased. MIT_C is poorly affected by inert particle size when limestone is used. The MIT_L of pure flour is higher than the MIT_L of mixtures containing up to 40% of 32–75 μm of limestone. This was probably due to the behaviour of pure flour during the test, which demonstrated strong tendency to produce char, cracks in the layer and detachment from the hot plate.     

Inhibition effects of aluminum dust explosions by various kinds of ammonium polyphosphate

In this work, vinyltriethoxysilane (A151) and 3-aminopropyltriethoxysilane (KH550) were used to modify ammonium polyphosphate (APP), showing that the dispersibility of APP could be improved remarkably by A151 and KH550. The maximum explosion pressure of aluminum dust explosion decreased with the addition of APP, A151-APP (APP-A) and KH550-APP (APP-B), with the exception of the case where the inerting ratio (α) of APP-A was less than 0.4. After the addition of APP-B, there was little difference in flame propagation behavior and explosion pressure compared with that of adding APP, indicating that APP-B could retain the inhibition performance of APP compared with APP-A. When the inerting ratios of APP, APP-A and APP-B were 1.2, 1.4 and 1.4, respectively, the aluminum dust explosion could be completely inhibited. The explosion residues of aluminum dust/APP mainly consisted of Al₂O₃, P-containing and N-containing compounds. It could be analyzed that APP exerted the inhibition effect through both chemical and physical effects.     

Effect of admixture of solid inertant on fire hazard of dust layers oriented at varying degrees of inclination

Unlike metallic dust layers, the layer flammability levels (LFL) of non-metallic dust layers exhibit a wide range from Class 1 (No self-sustained combustion) to Class 6 (explosive combustion). However, determinations of layer flammability have not considered the effect of inclination angle, thereby potentially underestimating fire hazard of combustible dust layers in many industrial situations. In this research, inclined dust layers showed greater fire hazard than did horizontally oriented dust layers. For example, LFL of wood dust jumped from class 3 to class 5 when layers were positioned with an incline. Flame spread rate of PMMA dust layers increased from 1.8 to 3.6 mm/s when the angle of inclination increased from 0 to 40°. Even small amounts of solid inertant significantly decreased surface layer fires. The required amount of inertant to completely inert layer fires was far less than that for smoldering layer fires or dust explosions.     

小苏打对红色彩跑粉粉尘云爆炸极限氧浓度的影响*

为研究彩跑粉的爆炸强度和爆炸敏感性,采用20 L球形爆炸实验系统和热重-差热分析仪开展实验,在分析红色彩跑粉爆炸压力和爆炸极限氧浓度(LOC)的基础上,进一步揭示小苏打对红色彩跑粉爆炸极限氧浓度的影响规律。研究结果表明:在玉米粉中添加红色食用色素后形成的彩跑粉会增加爆炸风险,爆炸猛烈度属于St1级;在50~400 g/m3粉尘浓度范围内,红色彩跑粉的LOC值先减小后增大,在200 g/m3时LOC值达到最低9%;当添加不同比例小苏打对红色彩跑粉爆炸风险进行抑制时,发现LOC值随着红色彩跑粉与小苏打混合性粉尘掺混比的增大而增大,在掺混比为50%时,红色彩跑粉与小苏打混合性粉尘的LOC值为21%。研究结果可为彩跑粉加工厂的抑爆和惰化防爆技术提供基础数据参考。     

Biomass explosion testing: Accounting for the post-test residue and implications on the results

This work uses the ISO 1 m³ dust explosion equipment to study the explosion properties and combustion characteristics of pulverized biomass dust clouds. An unreported feature of this apparatus is that in rich concentrations only about half the dust injected is burned in the explosion, while the overpressures remain high. This work was undertaken to try to understand the mechanisms of these phenomena, through the accounting of the debris at the end of the explosion, some of which was found in the form of impacted “cake” against the vessel wall. One possible explanation is that the residue material was biomass dust blown ahead of the flame by the explosion induced wind, impacted on the walls where then the flame side underwent flame impingement pyrolysis and the metal (wall) side material was compacted but largely chemically unchanged. The results also show that the heat transfer insulation provided by the powder wall layer contributes to the higher observed pressures. The risk of explosion with significant overpressures remains at 100% in very rich environments (equivalence ratios of up to 6) although these environments are leaner than thought due to material sequestration within the “cake”. There was little indication that a rich combustion limit was approached, this was determined in standard testing equipment that has been modified and calibrated to handle larger quantities of powder than normal.     

混合金属粉尘爆炸最小点火能量影响因素研究*

为探究混合金属粉尘爆炸危险性及与单一粉体爆炸特性差异，确保车间安全生产，采用粉尘云点火能量测试系统对车间混合金属粉尘及铝粉最小点火能量在不同影响因素下的变化规律及2种粉尘火焰变化特征进行测试。研究结果表明:混合金属粉尘和铝粉最小点火能量在一定范围内（38~96 μm）与粒径呈正相关性，当混合金属粉尘粒径大于75 μm时，所需最小点火能量大于1 000 mJ，其爆炸敏感性迅速降低，此时铝粉仍有较强爆炸敏感性；2种粉尘最小点火能量随质量浓度增加呈先降低后升高的趋势，最小点火能分别为295，15 mJ，对应的敏感质量浓度为600，1 000 g/m3，混合金属粉尘在质量浓度为500~700 g/m3时具有较大爆炸危险性；同铝粉相比，混合金属粉尘点火能量更高、火焰燃烧时间更短、火焰高度更低、爆炸剧烈程度更弱。     

Experimental investigation on explosion flame propagation of wood dust in a semi-closed tube

In order to explore flame propagation characteristics during wood dust explosions in a semi-closed tube, a high-speed camera, a thermal infrared imaging device and a pressure sensor were used in the study. Poplar dusts with different particle size distributions (0–50, 50–96 and 96–180 μm) were respectively placed in a Hartmann tube to mimic dust cloud explosions, and flame propagation behaviors such as flame propagation velocity, flame temperature and explosion pressure were detected and analyzed. According to the changes of flame shapes, flame propagations in wood dust explosions were divided into three stages including ignition, vertical propagation and free diffusion. Flame propagations for the two smaller particles were dominated by homogeneous combustion, while flame propagation for the largest particles was controlled by heterogeneous combustion, which had been confirmed by individual Damköhler number. All flame propagation velocities for different groups of wood particles in dust explosions were increased at first and then decreased with the augmentation of mass concentration. Flame temperatures and explosion pressures were almost similarly changed. Dust explosions in 50–96 μm wood particles were more intense than in the other two particles, of which the most severe explosion appeared at a mass concentration of 750 g/m³. Meanwhile, flame propagation velocity, flame propagation temperature and explosion pressure reached to the maximum values of 10.45 m/s, 1373 °C and 0.41 MPa. In addition, sensitive concentrations corresponding to the three groups of particles from small to large were 500, 750 and 1000 g/m³, separately, indicating that sensitive concentration in dust explosions of wood particles was elevated with the increase of particle size. Taken together, the finding demonstrated that particle size and mass concentration of wood dusts affected the occurrence and severity of dust explosions, which could provide guidance and reference for the identification, assessment and industrial safety management of wood dust explosions.