H-ZSM-5分子筛吸附-氧化NOx的研究

针对湿法脱硫后船舶尾气特点,考察了3种不同硅铝比的H-ZSM-5分子筛对船舶脱硫后尾气中NO_x的吸附-氧化过程及其影响因素,并采用TPD研究了干气下不同硅铝比的分子筛吸附饱和后的脱附情况.结果表明:干气条件下,硅铝比低的分子筛具有较好的吸附效果;硅铝比高的分子筛具有较好的抗水性,但从干气到饱和湿度下,硅铝比为300的分子筛的NO氧化率从36%降至18%;干气下,低温有利于分子筛的吸附-氧化;分子筛用量增加能够增加其对NO_x的吸附效果和氧化效果.TPD结果表明:NO和NO2共吸附在分子筛上,3种分子筛中脱附出的NO_x中NO2均占脱附总量的80%以上,但在600℃时,NO_x在分子筛上脱附仍不完全.     

ZSM-5分子筛疏水改性及催化H_2O_2氧化苯酚的性能研究

以甲苯为溶剂、三甲基氯硅烷(TMCS)为表面改性剂,采用液相接枝的方法对ZSM-5分子筛进行疏水化改性,通过XRD、FTIR、N2吸附-脱附、TG、水静态吸附试验等手段对改性前后的ZSM-5分子筛进行了表征,并将其应用于苯酚的吸附及催化氧化研究。结果表明:改性后ZSM-5分子筛仍保持原有的孔道结构,-Si(CH3)3基团接枝到孔道表面,使比表面积和孔容、孔径均有下降;改性后ZSM-5分子筛水静态吸附率由3.82%降至1.12%,疏水性得到明显提高;改性后ZSM-5分子筛对苯酚的吸附机理符合Langmuir模型,吸附动力学符合准二级动力学模型,且对水中苯酚的饱和吸附量由30.7mg/g增加到36.9mg/g;疏水改性后的分子筛负载MnO2催化H2O2氧化降解苯酚的效率可达86.2%,且其吸附过程与催化氧化过程具有协同效应。     

硅铝比和NiO对ZSM-5协同低温等离子体降解甲苯的影响

研究了不同硅铝比的ZSM-5与Ni/ZSM-5分子筛协同低温等离子体技术对甲苯降解性能的影响.以Ni O(Nickel Oxide)为活性组分,采用浸渍法对ZSM-5分子筛进行改性,利用氮气吸附脱附(BET)、X射线衍射仪(XRD)、X射线光电子能谱分析(XPS)、H_2程序升温还原(H_2-TPR)、NH_3程序升温脱附(NH_3-TPD)、Toluene程序升温脱附(Toluene-TPD)等技术表征样品的物理化学性质.考察了硅铝比对ZSM-5与Ni/ZSM-5分子筛体系中甲苯的吸附性能,研究了不同放电电压下硅铝比对甲苯降解率、碳平衡及二氧化碳选择性的影响,并采用气相色谱-质谱联用仪(GC-MS)分析了催化剂表面的有机产物.结果表明:硅铝比不但影响分子筛本身的物理化学特性(比表面积、氧化还原性能、表面酸性、疏水性等),还会影响Ni的负载形态和方式,更高的硅铝比与Ni O的负载能促进甲苯深度氧化,减少副产物,提高碳平衡和二氧化碳选择性.     

两种ZSM-5沸石分子筛吸附水中氨氮的研究

考察了两种硅铝比分别为25及50的ZSM-5沸石分子筛对水中氨氮的吸附性能及影响因素.研究表明,25℃时,25H及50H型沸石的吸附平衡时间分别为10 min和35 min,吸附等温线均符合Langmuir经验模型,25 H型分子筛的饱和吸附容量较大,为7.83 mg/g,50H型分子筛为4.36 mg/g.当吸附剂投...     

ZSM-5沸石分子筛吸附-脱附VOCs的性能研究

以不同Si/Al比的ZSM-5分子筛为吸附剂,考察了硅铝比对其疏水性和吸附性能的影响.结果表明,随着Si/Al比的增加,其微孔孔体积和微孔表面积变大,当Si/Al100时,ZSM-5分子筛均具有良好的疏水性和对甲苯的选择性吸附能力,但脱附温度随之升高.同时,以4类VOCs(醇类、酯类、烃类、酮类)为吸附质,研究了ZSM-5分子筛吸附-脱附不同VOCs的性能.发现ZSM-5分子筛由于具有丰富的微孔结构更适合吸附小分子VOCs,对于同类VOCs分子,随着碳数的增加,分子大小和极性均增大,其与分子筛的作用力越强,热脱附温度越高,但VOCs在ZSM-5分子筛表面300℃左右就能脱附完全.     

疏水型H-ZSM-5分子筛上NO氧化反应的研究

针对NO低温氧化催化剂的抗水汽性差的问题,以疏水型高硅H-ZSM-5分子筛为NO氧化催化剂,在温度为10~90℃、NO进口浓度为0.05%~0.08%,及相对湿度为0~100%条件下,考察了NO的氧化反应.结果表明,H-ZSM-5分子筛的硅铝比由50提高至300时,湿气条件(水汽含量1.18%)下,NO氧化率由20%升高至56%;干气下,低温有利于NO氧化;湿气下(水汽含量1.18%),NO氧化率随着温度的升高先增加后减少,最佳反应温度为20℃,与NOx工业废气的排放温度相近.200h的稳定性试验结果显示,在30℃、NO进口浓度0.08%、空时0.5s、保持相对湿度为50%或100%时,NO氧化率可维持在60%和50%,催化剂具有良好的稳定性.     

金属阳离子对高硅分子筛催化氧化NO的影响

采用离子交换法制备了Na-、K-、Co-、NiZSM-5分子筛催化剂.测试了它们催化氧化NO的性能并通过XRD、BET、ICP-MS和Py-IR等表征,结果表明,CoZSM-5分子筛对NO催化氧化具有最高的活性,氧化率达到47%,主要是引入Co离子的ZSM-5表面酸性最适宜NO氧化.同时,在湿度100%条件下,考察了氧气浓度（5%~20%）,空速与二氧化硫浓度（0~200×10^-6）等对CoZSM-5分子筛催化氧化NO性能的影响.实验结果表明,在30℃、空速14400h^-1和相对湿度100%条件下,SO₂浓度在200×10^-6以下对催化氧化NO基本无影响.56h催化剂稳定性实验结果表明,在30℃、NO进口浓度600×10^-6、空速18000h^-1和饱和水汽（RH：100%）条件下,CoZSM-5分子筛催化剂对NO的氧化率可维持在40%左右.因此CoZSM-5分子筛催化剂具有良好的NO氧化稳定性、抗水性和一定的抗硫性.     

介孔钛硅分子筛的表面化学特征及除铅机制研究

以表面活性剂在水溶液中形成的液晶相为模板剂，考察了钛含量对制备介孔钛硅分子筛性质的影响；应用表面络合反应关系式计算了介孔钛硅分子筛表面络合反应的基本特征参数。研究了溶液ｐＨ值、温度等对Ｐｂ＾２＋离子在介孔钛硅分子筛表面吸附的影响；并就Ｐｂ＾２＋离子在介孔钛硅分子筛表面的吸附动力学、吸附等温线和吸附机理进行了探讨。     

两种不同硅铝比的ZSM-5型分子筛去除水中Pb~(2+)的研究

考察硅铝比不同的ZSM-5两种分子筛(25H和50H,25和50为硅铝比:SiO2/Al2O3)对水中Pb2+离子的吸附去除效能。两种材料均可有效吸附去除水中Pb2+离子,吸附等温线符合Langmuir吸附等温式,25H的最大吸附容量达22.22mg/g,吸附动力学符合假二阶动力学模型,吸附速率及吸附容量顺序为:25H>50H。随着投加量的增加,分子筛对Pb2+的去除率呈上升趋势。常见共存阳离子均对分子筛吸附去除Pb2+产生影响。     

硅铝比对分子筛吸附氨氮性能的影响

基于X射线荧光光谱法确定的4种ZSM5分子筛硅铝比,分析了不同硅铝比分子筛吸附氨氮性能的差异,结合扫描电镜、X射线衍射分析结果,从分子筛的骨架组成、表面形貌和晶体结构角度,考察了硅铝比对分子筛吸附氨氮性能的影响机制;并探讨了分子筛骨架脱硅对其吸附性能的改善作用,为分子筛应用于污水厂尾水深度脱氮提供技术参考.结果表明,不同硅铝比分子筛的表面形貌、晶体结构与吸附氨氮性能具有显著差异：随着分子筛硅铝比增加,其结晶度下降、晶粒形态逐渐模糊、吸附容量降低;当实际硅铝比由35增大至237时,氨氮平衡吸附量由5.65mg/g降至0.41mg/g,由Langmuir吸附等温式确定的饱和吸附量由6.5963mg/g下降至0.4430mg/g.分子筛吸附过程符合准二级动力学模型,吸附速率受离子交换化学吸附作用机理控制,随着硅铝比升高分子筛的离子交换容量下降,其吸附速率降低.分子筛骨架脱硅能够显著改善其氨氮吸附性能,硅铝比为35的分子筛经碱蚀脱硅处理后,其氨氮平衡吸附量提高81.6%,该方法为改善分子筛吸附性能提供了一种有效的技术途径.     

Effect of Mo contents on properties of Mo/ZSM-5 zeolite catalyst for NOx reduction

Mo/ZSM-5 catalysts with different Mo content were prepared by impregnation method. The effect of Mo content on the property of Mo/ZSM-5 catalysts and their performance for selective catalytic reduction(SCR) of NO with ammonia was investigated by XRD, ICP,XPS and NO-TPD respectively. The results showed that the catalytic activity of Mo/ZSM-5 for SCR of NO is strongly influenced by the Mo loading in HZSM-5 zeolites. The NOx conversion reached the highest value of 64.2% at 375℃ when Mo content is about 10.9%, and the temperatures at which the maximum of NOx conversion obtained were declined with the increase of Mo content. From XRD results, it can be seen that it exhibits the distinct interaction between Mo and HZSM-5 when Mo content is about 10.9%. This may result in a suitable phase structure in Mo/ZSM-5 catalyst, which is advantageous for NO reduction. XPS and NO-TPD results also showed that the catalytic activity of Mo/ZSM-5 may be related to the Mo percent on the surface.     

Kinetics of selective catalytic reduction of NO by NH_3 on Fe-Mo/ZSM-5 catalyst

The catalyst of Fe-Mo/ZSM-5 has been found to be more active than Fe-ZSM-5 and Mo/ZSM-5 separately for selective catalytic reduction (SCR) of nitric oxide (NO) with NH_3.The kinetics of the SCR reaction in the presence of O_2 was studied in this work.The results showed that the observed reaction orders were 0.74-0.99,0.01-0.13,and 0 for NO,O_2 and NH_3 at 350-450℃,respectively. And the apparent activation energy of the SCR was 65 kJ/mol on the Fe-Mo/ZSM-5 catalyst.The SCR mechanism was also deduced. Adsorbed NO species can react directly with adsorbed ammonia species on the active sites to form N_2 and H_2O.Gaseous O_2 might serve as a reoxidizing agent for the active sites that have undergone reduction in the SCR process.It is also important to note that a certain amount of NO was decomposed directly over the Fe-Mo/ZSM-5 catalyst in the absence of NH_3.     

Kinetics of selective catalytic reduction of NO by NH3 on Fe-Mo/ZSM-5 catalyst

The catalyst of Fe-Mo/ZSM-5 has been found to be more active than Fe-ZSM-5 and Mo/ZSM-5 separately for selective catalytic reduction (SCR) of nitric oxide (NO) with NH3. The kinetics of the SCR reaction in the presence of O2 was studied in this work. The results show that the observed reaction orders were 0.74-0.99, 0.01-0.13, and 0 for NO, O2 and NH3, respectively, at 350-450℃. And the apparent activation energy of the SCR was 65 kJ/mol on the Fe-Mo/ZSM-5 catalyst. The SCR mechanism was also deduced. Adsorbed NO species can react directly with adsorbed ammonia species on the active sites to form N2 and H2O. Gaseous O2 might serve as a reoxidizing agent for the active sites that have undergone reduction in the SCR process. It is also important to note that a certain amount of NO was decomposed directly over the Fe-Mo/ZSM-5 catalyst in the absence of NH3.     

钴铜改性的ZSM-5对低浓度NO吸附性能的研究

利用固定吸附床研究了不同金属离子改性的ZSM-5分子筛对一氧化氮的吸附性能。实验发现:在过渡金属同钴离子一起改性的ZSM-5中,钴铜金属离子共同改性的ZSM-5分子筛对一氧化氮的吸附性能最好;当铜钴离子共同浸渍、铜钴离子浸渍量比(n(Cu) n(Co))为0 8和Al2O3(粘合剂)用量w(Al2O3)为23%时,改性的ZSM-5分子筛既具有良好的吸附性能又有良好的机械强度。另外,实验还发现改性分子筛吸附一氧化氮的穿透时间随吸附温度的升高而缩短,并利用热重技术,分析了吸附剂的热再生问题。      

Study on the removal of NOx from simulated flue gas using acidic NaClO2 solution

The study on the removal of NOx from simulated flue gas has been carded out in a lab-scale bubbling reactor using acidic solutions of sodium chlorite. Experiments were performed at various pH values and inlet NO concentrations in the absence or presence of SO2 gas at 45℃. The effect of SO2 on NO oxidation and NO2 absorption was critically examined. The oxidative ability of sodium chlorite was investigated at different pH values and it was found to be a better oxidant at a pH less than 4. In acidic medium, sodium chlorite decomposed into C102 gas, which is believed to participate in NO oxidation as well as in NO2 absorption. A plausible NOx removal mechanism using acidic sodium chlorite solution has been postulated. A maximum NOx removal efficiency of about 81% has been achieved.     

烟气脱氮体系中络合吸收剂的氧化还原过程

在填料吸收塔中,考察NO和O₂共存时,NO浓度、O₂含量对脱氮效率、Fe^II(EDTA)氧化速率以及Fe^III(EDTA)生物还原速率的影响,并对该系统的主要反应过程进行了分析.结果表明,同时吸收NO可促进Fe^II(EDTA)的氧化,当进气NO浓度由0增至500cm³/m³时,表观氧化反应速率常数由0.00451min^-1增至0.00604min^-1;Fe^II(EDTA)的氧化反应对于O₂含量为1级反应,表观氧化速率常数与O₂含量成线性关系;增加气体中NO浓度或O₂含量均会使Fe^III(EDTA)的生物还原反应速率下降;微生物对氧化中间产物的还原可以减缓NO对Fe^II(EDTA)氧化的促进作用,因而气相中NO和O2共存时对Fe^III(EDTA)生物还原的影响小于各单一组分存在时的影响之和.     

气相臭氧氧化协同湿法吸收脱硝技术的性能和氮转化

气相臭氧氧化协同湿法吸收脱硝技术具有脱除效率高、设备简单、投资低、运行易控等优点,适用于钢铁烧结、焦炉和陶瓷等较低温度（<150℃）和较低NO_x浓度（<400 mg/m3）烟气的深度净化。从理论上分析了臭氧氧化协同湿法吸收脱硝反应过程物理化学行为,并采用傅里叶红外光谱和离子色谱等方法,分别考察了气相臭氧氧化NO和气相臭氧氧化协同湿法吸收脱硝的氮产物分布,计算氮转化率。结果表明:n（O₃）:n（NO）和水溶性是影响NO氧化程度和氧化产物吸收脱除效率的关键因素。当n（O₃）:n（NO）>1.5时,NO的氧化产物是与SO₂水溶性相当的N₂O₅和HNO₃,均可实现在传统脱硫吸收塔中同步高效脱除,而且产物为稳定性良好的NO₃-。氮平衡分析结果表明,氮转化率接近99%,而不可检测的氮组分可以忽略不计或者不存在。     

Application of high silica zeolite ZSM-5 in a hybrid treatment process based on sequential adsorption and ozonation for VOCs elimination

In this study, a hydrophobic synthetic zeolite, namely ZSM-5 is chosen as an adsorbent/catalyst for toluene removal. Experimental results showed that toluene adsorption onto ZSM-5 was favourable, following a Langmuir adsorption isotherm model. ZSM-5 zeolite was regenerated using gaseous ozone at low temperature. Adsorbed toluene was oxidised, releasing mainly CO₂ and H₂O. Traces of oxidation by-products such as acetic acid and acetaldehyde were formed and remained adsorbed after the oxidativate regeneration with ozone. After four successive cycles of adsorption/ozonation, the adsorption efficiency was not affected (92%–99%). These results showed that volatile organic compound (VOC) removal by adsorption onto ZSM-5 zeolite followed by ozone regeneration could be used as a promising hybrid process for the control of VOC emissions in terms of efficiency.     

烟气条件对直流电晕自由基簇射NO氧化过程的影响

运用以湿空气为自由基源物质的直流电晕自由基簇射系统,研究了烟气在反应器内的滞留时间、烟气流速和NO浓度对NO氧化过程的影响.结果表明:烟气流速的增加会抑制电晕放电的发展,而烟气中NO浓度的增加则使放电变得更加容易.NO的氧化受烟气在反应器内滞留时间的影响较小,而它受烟气流速的影响较大.在2W的输入功率下,当烟气在反应器内的滞留时间从8.5s增加到34.2s时,NO的氧化率只从54.5 %提高到57.6 %.而在1.7W·h/m³的能量密度下,当烟气流速从1.4cm/s增加到6.3cm/s时,NO的氧化率从60.0%减少到38.6%,能量利用率也从20.8g/(kW·h)下降到了13.3g/(kW·h).在湿空气流量一定的情况下,NO初始浓度存在一个最佳值,本实验中最佳的NO浓度为100×10^-6左右.