Experimental study on methane explosion characteristics with different types of porous media

Porous media has a significant effect on flame and overpressure of methane explosion. In this paper, the pore diameter and thickness of porous media are studied. Nine experimental combinations of different pore diameter and thickness on the propagation of flame and overpressure of methane explosion in a tube are analyzed. The results show that the porous media not only can suppress the explosive flame propagation, but the porous media with large pore diameter can cause deflagration and accelerate the transition of flame from laminar to turbulent. The pore diameter of the porous media mainly determines the quenching of the flame. Simply increasing the thickness of porous media may cause the flame to temporarily stop propagating, but the flame is not completely extinguished for larger pore diameter. However, the deflagration propagation speed of flame is affected by the thickness. The attenuation of overpressure by porous media is mainly reflected in reducing the duration of overpressure and the peak value of overpressure. The smaller the pore diameter, the greater the thickness, and the more remarkable the reduction in overpressure duration and peak value. Suitable pore diameter and thickness of porous media can effectively suppress flame propagation and reduce the maximum value and duration of overpressure.     

泡沫金属对甲烷/空气爆燃火焰的淬熄实验研究

为研究多孔材料对甲烷/空气预混气体爆燃火焰的抑制淬熄效果,运用一套自主设计的管道爆炸抑制系统进行实验研究。在实验中运用高速摄像机记录爆燃火焰在穿过多孔材料板时的淬熄过程,采用20,40,60,80PPI (孔目数) 的4种多孔材料,研究不同孔目数的多孔材料对爆燃火焰传播的形态结构、火焰传播速度以及抑制淬熄等特性的影响。结果表明:多孔材料的孔目数对爆燃火焰传播的早期阶段影响较小,爆燃火焰都经历了半球形火焰和指形火焰阶段;当火焰传播到多孔材料板时,孔目数越大对火焰的降速作用越强,80PPI工况下爆燃火焰不能穿过多孔材料板,即发生淬熄。实验结果揭示了多孔材料对火焰的淬熄作用与微孔通道和火焰的相互作用有关。     

Study on the preparation of novel NiB/Hβ-Al2O3 micro-mesoporous suppressant and its inhibition mechanism of coal dust explosion flame

Coal dust explosion is one of the serious accidents in the coal industry. It is of great significance to study the flame suppression of coal dust explosions. In this paper, a novel active component NiB with amorphous structure for explosion suppression was synthesized by the chemical reduction method. Furthermore, the novel explosion suppressant NiB/Hβ-Al₂O₃ was prepared through the kneading method by loading novel amorphous NiB nanoparticles on Hβ-Al₂O₃ with the micro-mesoporous structure as the carrier. The morphology and structure of NiB/Hβ-Al₂O₃ were characterized by XRD, BET, SEM, and FTIR, which showed that the NiB/Hβ-Al₂O₃ has proper pore structure and NiB nanoparticles are uniformly distributed as active components for explosion suppression in suppressant. Hartmann tube was used to evaluate the inhibition of coal dust deflagration. The results showed that the flame propagation distance and velocity decreased with the increase of the explosion suppressant. When the addition of explosion suppressant was 30 wt%, the explosion of coal dust was suppressed effectively. Furthermore, combing with the analysis results of the products after coal dust deflagration, the physical and chemical inhibition mechanism of the novel NiB/Hβ-Al₂O₃ explosion suppressant on coal dust deflagration was put forward.     

Experimental study on vented deflagration of hydrocarbon fuel-air mixtures in a 20-L semi-confined cylindrical vessel with a slight static activation pressure

The overpressure peaks and flame propagation characteristics of hydrocarbon fuel-air mixtures vented deflagration in a 20-L cylindrical vessel with a slight static activation overpressure (P_ST = 2.5 kPa) and five vent opening ratio were studied by a series of experiments. The experiments focused on the effect of vent opening ratio on the overpressure peaks and flame propagation characteristics of hydrocarbon fuel-air mixture vented deflagration. The internal overpressure-time profiles and high-speed photographs of flame propagation processes were obtained. The results showed that three overpressure peaks were distinguished in the internal overpressure-time profiles, caused by the burst vent cover (p_burst), the acceleration of burnt gas (p_fv), and the fierce external deflagration of vented unburned fuel (p_ext), respectively. The changing of the vent opening ratio had almost no effect on the value of p_burst and (dp_burst/dt). With increasing vent opening ratio, the values of p_fv, p_ext, (dp_fv/dt) and (dp_ext/dt) showed a decreasing trend while the values of p_burst and (dp_burst/dt) were nearly constant. The flame presented a hemispherical shape before the vent cover ruptured then developed as a mushroom shape after accelerated to external field. There were three flame speed peaks during flame propagation process, resulted from venting flow acceleration, external deflagration, and axial heat flux formed by internal combustion. With the increase of vent opening ratio, all of the maximum flame speed, external average flame speed, maximum flame distance and external flame duration showed a downward trend, excepting for the internal average flame speed almost remained constant.     

Effects of combined porous media on quenching and re-ignition characteristics of methane/air premixed combustion in a duct

During the study of foam metal suppression of methane combustion in ducts, it was found that under certain conditions, after the flame is extinguished, a re-ignition phenomenon occurs in the area upstream of the foam metal. In this paper, the process and mechanism for the occurrence of this phenomenon were investigated. The porous media used in the experiments is a two-layer structure consisting of a combination of iron-nickel foam and copper foam and was mounted in a transversal position. Each layer of foam metal has a thickness of 5 mm and a pore size of 20 or 40 holes pores per inch (ppi). The results show that flame extinguishment and re-ignition are highly dependent on the material and pore density of the porous media used. After the flame was quenched by the combination of iron-nickel foam with the same pore density of 40ppi, the re-ignition intensity was higher (a dazzling white light could be observed) and the flame area was larger. However, when a combination of iron-nickel foam with different pore densities was used, the re-ignition intensity, flame oscillation frequency and amplitude were significantly lower. However, both re-ignition flames can last for a long time. In addition, the incorporation of copper foam with high thermal conductivity resulted in the decay of flame propagation speed and the overpressure before and after quenching increased significantly with the increase of pore density of the first layer of iron-nickel foam.     

Large eddy simulation of methane–air deflagration in an obstructed chamber using different combustion models

In this paper, simulations of methane–air deflagration inside a semi-confined chamber with three solid obstacles have been carried out with large eddy simulation (LES) technique. Three sub-grid scale (SGS) combustion models, including power-law flame wrinkling model by Charlette et al., turbulent flame speed closure (TFC) model, and eddy dissipation model (EDM), are applied. All numerical results have been compared to literature experimental data. It is found that the power-law flame wrinkling model by Charlette et al. is able to better predict the generated pressure and other flame features, such as flame structure, position, speed and acceleration against measured data. Based on the power-law flame wrinkling model, the flame–vortex interaction during the deflagration progress is also investigated. The results obtained have demonstrated that higher turbulence levels, induced by obstacles, wrinkle the flame and then increase its surface area, the burning rates and the flame speed.     

The effect of orifice plates with different shapes on explosion propagation of premixed methane–air in a semi-confined pipeline

The effect of internal shape of obstacles on the deflagration of premixed methane–air (concentration of 10%) was experimentally investigated in a semi-confined steel pipeline (with a square cross section size of 80 mm × 80 mm and 4 m long). The obstacles used in this study were circular, square, triangular and gear-shaped (4-teeth, 6-teeth and 8-teeth) orifice plates with a blockage ratio of 75%, and the perimeter of the orifice was regarded as a criterion for determining the sharpness of the orifice plate. The overpressure history, flame intensity histories, flame front propagation speed, maximum flame intensity and peak explosion overpressure were analyzed. The explosion in the pipeline can be divided into two stages: initial explosion and secondary explosion. The secondary explosion is caused by recoiled flame. The perimeter is positively related to the intensity of the recoiled flame and the ability of orifice plate to suppress the explosion propagation. In addition, the increase in the perimeter will cause the acceleration of the flame passing through the orifice plate, while after the perimeter of the orifice reaches a certain value, the effect of the increase in perimeter on explosion excitation becomes no obvious. The overpressure (static pressure) downstream of the orifice plate is the result of the combined effect of explosion intensity and turbulence. The increase in perimeter leads to the increase in turbulence downstream of the orifice plate which in turn causes more explosion pressure to be converted into dynamic pressure.     

预混乙炔-空气爆燃火焰在平板狭缝中传播与熄灭的实验研究

通过对预混乙炔-空气爆燃火焰在平板狭缝中的传播与熄灭过程进行试验研究，分析临界火焰传播速度、狭缝高度和熄灭长度之间的关系。实验结果表明，当狭缝高度一定时，临界火焰传播速度越大，熄灭长度越大，熄灭长度与临界火焰传播速度近似呈正比例关系。在相同的临界火焰传播速度条件下，随着狭缝高度的增加，熄灭长度值迅速增大，说明狭缝高度对预混火焰的传播与熄灭有显著影响。     

乙炔-空气预混火焰在狭窄通道中的传播与熄灭

针对预混火焰在狭窄通道中传播过程的研究是进行阻隔防爆技术研发的基础。本文首先通过数值计算模拟了预混乙炔一空气爆燃火焰在狭窄通道中的传播与熄灭过程,然后采用高速数字摄像技术对火焰的传播过程进行捕捉,分析临界火焰传播速度、狭缝高度和熄灭长度之间的关系。研究结果均表明,当狭缝高度一定时,临界火焰传播速度越大,熄灭长度越大,熄灭长度与临界火焰传播速度近似呈正比例关系。在相同的临界火焰传播速度条件下,随着狭缝高度的增加,熄灭长度值迅速增大,说明狭缝高度对预混火焰的传播与熄灭有显著影响。本文研究成果将可为工业阻火防爆装置的设计和实际应用提供参考依据。     

Inerting characteristics of ultrafine Mg(OH)2 on starch dust explosion flame propagation

Experiments on the flame propagation of starch dust explosion with the participation of ultrafine Mg(OH)₂ in a vertical duct were conducted to reveal the inerting evolution of explosion processes. Combining the dynamic behaviors of flame propagation, the formation law of gaseous combustion products, and the heat dissipation features of solid inert particles, the inerting mechanism of explosion flame propagation is discussed. Results indicate that the ultrafine of Mg(OH)₂ powders can cause the agglomeration of suspended dust clouds, which makes the flame combustion reaction zone fragmented and forms multiple small flame regions. The flame reaction zone presents non-homogeneous insufficient combustion, which leads to the obstruction of the explosion flame propagation process and the obvious pulsation propagation phenomenon. As the proportion of ultrafine Mg(OH)₂ increases, flame speed, flame luminescence intensity, flame temperature and deflagration pressure all show different degrees of inerting behavior. The addition of ultrafine Mg(OH)₂ not only causes partial inerting on the explosion flame, but also the heat dissipation of solid inert particles affects the acceleration of its propagation. The explosion flame propagation is inhibited by the synergistic effect of inert gas-solid phase, which attenuates the risk of starch explosion. The gas-solid synergistic inerting mechanism of starch explosion flame propagation by ultrafine Mg(OH)₂ is further revealed.     

Explosion suppression of porous materials in a pipe-connected spherical vessel

To study the suppression of different porous materials on the explosion of combustible gas, some experiments were implemented. The porous materials were categorized into three kinds, including six subcategories, and the explosion suppression characteristics of the thin iron hoop, one-layer porous materials, two-layer composite porous materials, and three-layer composite porous materials were studied and analyzed. The results show that a rarefaction wave appears in the spherical vessel during the rapid development stage of combustion explosion. Further, the thin iron hoop could enhance the gas explosion intensity. And the explosion intensity suppression effect of the porous materials is obvious, the best effects of one-layer, two-layer and three-layer porous materials are from Fe–Ni 10 mm/40 PPI, Fe–Ni 10 mm/90 PPI + Al₂O₃ 10 mm/30 PPI, and Al₂O₃ 10 mm/50 PPI + Fe–Ni 10 mm/40 PPI + SiC 20 mm/20 PPI, respectively. According to the surface morphology of the porous materials, the anti-sintering ability of the three categories of porous materials follows the order of Al₂O₃ > SiC > Fe–Ni. Besides, the thickness and pore size of the combined porous material was changed, which has a great influence on the explosion pressure and the explosion intensity.     

Efficient simulation of flame acceleration and deflagration-to-detonation transition in smooth pipes

Evaluation of accident scenarios including flame acceleration and deflagration-to-detonation transition (DDT) in chemical plant piping systems increases the need for an efficient numerical simulation tool capable of dealing with this phenomenon. In this work, a hybrid pressure-density-based solver including deflagrative flame propagation as well as detonation propagation is presented. The initial incompressible acceleration stage is covered by the pressure-based solver until the flame velocity reaches the fast flame regime and transition to the density-based solver is done. The deflagration source term is formulated in terms of a turbulent flame speed closure model incorporating various physical effects crucial for flame acceleration at low turbulence conditions (Katzy and Sattelmayer, 2018). Modelling of the detonation source term is based on a quadratic heat release function (Hasslberger, 2017). The presented numerical approach is validated in terms of DDT locations and pressure data from Schildberg (2015) as well as recently completed flame tip position measurements. For this purpose, H₂/O₂/N₂ mixtures ranging from 25.6 vol-% H₂ to 29.56 vol-% H₂ in two different pipe geometries are considered. The focus of the current work is on predicting the DDT location correctly and good agreement is observed for the investigated cases.     

球形障碍物对瓦斯爆燃火焰影响试验研究

为进一步开发煤矿井下瓦斯爆炸事故的隔抑爆技术装备,利用截面为0.2 m×0.2 m的方形管道、纹影仪和高速摄像机,开展无障碍物时和球形障碍物存在情况下的瓦斯爆燃传播试验。研究发现,无障碍物时,密闭管道内爆燃火焰的结构和传播速度受反射压力波的影响很大,湍流火焰、化学反应作用能力与反射压力波的相互作用是造成火焰传播速度变化的主要原因;球形障碍物存在时,火焰受扰动后被拉伸为前锋、中锋和尾锋,前锋速度最快,尾锋最慢;火焰前锋从经过障碍物开始整体呈加速趋势,与无障碍物相比,通过观察段的时间明显缩短。     

Effect of Al2O3 particle size reduction on aluminium dust explosion

To investigate the effect of Al₂O₃ particle size on an aluminum explosion, the overpressure and flame velocity in a vertical duct were evaluated. The results show that the inhibitory effect of submicron Al₂O₃ is best, while the inhibitory effect increases with increasing inerting ratio. However, the inhibitory effect of micron Al₂O₃ does not increase significantly after the inerting ratio exceeds 40%. For high-concentration aluminum powder, 0.8 μm Al₂O₃ with an inerting ratio less than 20% promotes aluminum explosion. As the inerting ratio increases beyond 20%, however, the overpressure decreases. Furthermore, Al₂O₃ inhibits the formation of the intermediate product AlO and decreases the flame brightness. As the inerting ratio of 0.8 μm Al₂O₃ reaches 50%, the white patches in the flame image disappear. The results of scanning electron microscopy showed that the explosion products agglomerate and some dot-like protrusions appear on the surface of the unburned aluminum particles. The inhibition mechanism was qualitatively investigated. Physical heat absorption is proven to play a limited role. Thermal radiation and chemical inhibition play a key role. The chemical effect mainly influences the surface reaction energy source.     

Effects of cross-wise obstacle position on methane–air deflagration characteristics

A vented chamber, with internal dimensions of 150 mm × 150 mm × 500 mm, is constructed in which the premixed methane–air deflagration flame, propagating away from the ignition source, interacts with obstacles along its path. Three obstacle configurations with different cross-wise positions are investigated. The cross-wise obstacle positions are found to have significant effects on deflagration characteristics, such as flame structure, flame front location, flame speed, and overpressure transients. The rate of flame acceleration, as the flame passes over the last obstacle, is the highest at the configuration with three centrally located obstacles, whereas the lowest is observed at the configuration with three obstacles mounted on one side of the chamber. Compared with the side configuration, the magnitude of overpressure generated increases by approximately 80% and 165% for the central and staggered configurations, respectively. Furthermore, flame propagation speeds and generated overpressures for both the central and staggered configurations are greater, which should to be avoided to reduce the risk associated with turbulent premixed deflagrations in practical processes.     

Simple method for predicting pressure behavior during gas explosions in confined spaces considering flame instabilities

It is indispensable to predict the pressure behavior caused by gas explosions for the safety management against accidental gas explosions. In this study, a simple method for predicting the pressure behavior during gas deflagrations in confined spaces was examined. Previously the pressure behavior was calculated analytically assuming laminar flame propagation. However, the results of this method often provide underestimation compared with experimental data. It was known the underestimation intensifies as the scale of explosion spaces becomes larger. On the large scale gas deflagration, flame instability (especially hydrodynamic instability) might be more effective and wrinkles appeared on the flame front. Then, the flame surface area was increased and the propagating flame was gradually accelerated. The ordinary prediction methods led to the underestimation because the propagating flame was assumed to be laminar. In this study, we considered the effect of flame wrinkles caused by flame instabilities. By regarding the flame front as a fractal structure, the flame surface area could be modified. Because a flame surface starts to be wrinkled on a certain flame radius, proper determination of the critical flame radius provided accurate prediction of pressure behavior on a large scale deflagration. In addition, correction of the K_G value in a large vessel was discussed.     

障碍物对油气-空气混合气体泄压爆炸火焰传播特性影响

为了研究障碍物对油气泄压爆炸火焰传播特性的影响规律,进行了不同数量障碍物工况下的对比实验,并利用纹影仪和高速摄影仪记录了火焰传播过程,针对障碍物对火焰形态、火焰锋面位置及火焰传播速度的影响规律进行了研究,结果表明:圆柱体障碍物会导致油气泄压爆炸火焰形态产生褶皱和弯曲变形,诱导层流火焰向湍流火焰转变,加速火焰的传播,对油气泄压爆炸火焰的初始传播形态有显著影响;随着障碍物数量的增多,火焰锋面传播距离点火端的最大距离增大,但到达最远距离的时间减少;障碍物能够增强火焰的传播速度,尤其对障碍物下游火焰影响最为显著,随着障碍物数量的增多,火焰传播的最大速度也随之增大,但达到最大火焰传播速度的时间却随之减少;障碍物的存在增大了油气泄压爆炸过程外部爆炸压力,并且随着障碍物数量的增多,外部爆炸压力峰值增长幅度增大。     

Numerical simulation of premixed methane–air deflagration in a semi-confined obstructed chamber

In this paper, large eddy simulation coupled with a turbulent flame speed cloure (TFC) subgrid combustion model has been utilized to simulate premixed methane–air deflagration in a semi-confined chamber with three obstacles mounted inside.The computational results are in good agreement with published experimental data, including flame structures, pressure time history and flame speed. The attention is focused on the flame flow field interaction, pressure dynamics, as well as the mechanism of obstacle-induced deflagration. It is found that there is a positive feedback mechanism established between the flame propagation and the flow field. The pressure time history can be divided into four stages and the pseudo-combustion concept is proposed to explain the pressure oscillation phenomenon. The obstacle-induction mechanism includes direct effect and indirect effect, but do not always occur at the same time.     

气体爆燃火焰在狭缝中的淬熄

通过叙述可燃气体爆燃火焰在平行板狭缝中传播时产生淬熄的实验和理论研究结果，给出了甲烷，丙烷，乙炔，氢气等四种可燃气体与空气的预混气作为实验介质所进行的爆火焰淬熄实验中，火焰传播速度与淬熄直径、淬熄长度之间的关系。对于气体爆燃火争的淬熄理论模型进行了探讨，得到了有应用价值的结论。