The explosion overpressure field and flame propagation of methane/air and methane/coal dust/air mixtures

The explosion of the methane/air mixture and the methane/coal dust/air mixture under 40 J center spark ignition condition was experimentally studied in a large-scale system of 10 m³ vessel. Five pressure sensors were arranged in space with different distances from the ignition point. A high-speed camera system was used to record the growth of the flame. The maximum overpressure of the methane/air mixture appeared at 0.75 m away from the ignition point; the thickness of the flame was about 10 mm and the propagation speed of the flame fluctuated around 2.5 m/s with the methane concentration of 9.5%. The maximum overpressure of the methane/coal dust/air mixture appeared at 0.5 m. The flame had a structure of three concentric zones from outside were the red zone, the yellow illuminating zone and the bright white illuminating zone respectively; the thickness and the propagation speed of the flame increased gradually, the thickness of red zone and yellow illuminating zone reached 3.5 cm and 1 cm, the speed reached 9.2 m/s at 28 ms.     

管道内瓦斯煤尘共混爆炸温度特性

采用瞬态火焰传播实验系统,对7%,8%,9%,10%和11%的瓦斯体积浓度分别与不同浓度的长焰煤煤尘混合,并使用直径25 μm的Pt/Rh13-Pt微细热电偶测量温度,揭示受限空间内瓦斯与煤尘混合爆炸温度特性。结果表明:煤尘浓度一定时,随着瓦斯浓度的增加,爆炸温度先增加后减小;纯瓦斯浓度在10%时爆炸温度最高,加入煤尘后的混合体系中,瓦斯浓度为9%时爆炸温度最高;瓦斯浓度不变时,随着煤尘浓度的增加,爆炸温度一直减小;7%~11%瓦斯分别与130 g/m3煤尘混合爆炸后测得最高温度分别为1 333.6,1 475.4,1 511.4,1 455.6,1 396.4 ℃;与9%纯瓦斯爆炸相比,9%瓦斯与130,260,520,780 g/m3煤尘混合爆炸后测得最高温度分别降低7.2%,11.5%,15.0%和22.9%。结论得到的瓦斯煤尘共混爆炸温度数据可为煤矿灾害高温防护提供参考依据。     

瓦斯煤尘爆炸特性及抑爆方法研究进展

为探究瓦斯煤尘爆炸特性及抑爆机理,本文通过一系列实验,研究瓦斯、煤尘爆炸的速度和温度等特征,提出利用图像相关系数法和辐射测温原理计算火焰传播速度及温度场变化,定量分析影响煤尘爆炸的因素以及产物变化规律,揭示煤尘爆炸的宏微观机制。结果表明:火焰分形维数可以用来反应瓦斯爆炸强度,即当分形维数更接近2.2937时爆炸反应最为强烈,其爆炸过程中自由基最终生成浓度与CH 4初始浓度呈倒U型关系;当量比对煤粉火焰爆炸压力及速度也有一定影响,在最佳当量比的2倍左右时可以达到最大爆炸压力和最大火焰传播速度。另外本文亦采用泡沫陶瓷对瓦斯的多次爆炸和连续爆炸进行抑爆,发现不同厚度和孔隙的泡沫陶瓷具有不同的抑制效果,孔隙较大的泡沫陶瓷对爆炸能量有较好的抑制作用。     

不同含水率煤尘在瓦斯爆炸诱导下爆炸传播规律研究

为了探究不同含水率煤尘在瓦斯爆炸诱导下的爆炸传播规律,利用自行搭建的直管瓦斯爆炸诱导煤尘二次爆炸实验系统,从冲击波压力和火焰传播速度2个方面,研究了不同含水率沉积煤尘在瓦斯爆炸诱导下的爆炸传播规律和原因。研究结果表明:当煤尘含水率小于40%时,管道内沉积煤尘会在瓦斯爆炸诱导下产生二次爆炸,同时沉积煤尘总量一定时,沉积煤尘二次爆炸产生的冲击波超压峰值和火焰传播速度随着煤尘含水率的增加先增大后减小;当沉积煤尘含水率为20% 时,煤尘二次爆炸产生的冲击波超压峰值、火焰传播速度峰值达到最大值,分别为1.657 MPa和468.060 m/s;当沉积煤尘含水率大于40%时,沉积煤尘无法产生二次爆炸,此时爆炸产生的威力小于单一瓦斯爆炸,火焰传播速度衰减较无煤尘的瓦斯爆炸更快,沉积煤尘起到抑制瓦斯爆炸传播的作用。研究结果可以为防治煤尘二次爆炸提供理论依据。     

障碍物对瓦斯煤尘爆炸火焰传播规律的影响

为了进一步探究瓦斯煤尘耦合爆炸火焰的传播规律,用自行搭建的半封闭垂直管道爆炸试验系统,研究障碍物对瓦斯煤尘耦合爆炸火焰传播规律的影响。研究结果表明:障碍物能显著提高瓦斯煤尘爆炸火焰的传播速度,其加速机理主要是障碍物诱导的湍流区会促进火焰的传播;火焰在传播过程中的加速度不是一直增加,随着火焰速度的增加会出现上下波动;煤尘的加入会使瓦斯爆炸产生的火焰传播速度显著增大及速度的最大值距离点火端较远;通过障碍物时爆炸产生的火焰形状发生较大的改变,出现拉伸和褶皱现象。     

Influences of coal dust components on the explosibility of hybrid mixtures of methane and coal dust

In order to study the influences of coal dust components on the explosibility of hybrid mixture of methane and coal dust, four kinds of coal dust with different components were selected in this study. Using the standard 20 L sphere, the maximum explosion pressure, explosion index and lower explosion limits of methane/coal dust mixtures were measured. The results show that the addition of methane to different kinds of coal dust can all clearly increase their maximum explosion pressure and explosion index and decrease their minimum explosion concentration. However, the increase in the maximum explosion pressure and explosion index is more significant for coal dust with lower volatile content, while the decrease in the minimum explosion concentration is more significant for coal dust with higher volatile content. It is concluded that the influence of methane on the explosion severity is more pronounced for coal dust with lower volatile content, but on ignition sensitivity it is more pronounced for coal dust with higher volatile content. Bartknecht model for predicting the lower explosion limits of methane/coal dust mixture has better applicability than Le Chatelier model and Jiang model. Especially, it is more suitable for hybrid mixtures of methane and high volatile coal dust.     

直线管道煤尘爆炸火焰传播规律的试验研究

为提供煤尘爆炸事故预防和缓解所需的科学依据,对煤尘爆炸火焰传播过程进行试验研究。所用试验装置,其主要部分为直径0.3 m的圆形管道与断面边长为80 mm的方形管道对接形成的一个长2 m的爆炸腔体。在其中共进行9次煤尘爆炸试验。结果表明,煤尘爆炸火焰传播具有速度快,波动大,稳定性较差的特点,火焰区长度远大于扬尘区长度,最大火焰速度和传播距离与煤尘量均不存在正比例关系,但存在一个特定的煤尘质量浓度。在这个特定质量浓度处,最大火焰速度达到最大值。当煤尘质量浓度大于这个特定质量浓度时,火焰传播速度曲线整体下降,暂时缺氧被认为是导致这一情况的重要因素。     

Experimental study of the effect of nitrogen addition on gas explosion

Flame propagation and combustion characteristics of methane/air mixed gas in gas explosion were studied in a constant volume combustion bomb. Stretched flame propagation velocity, unstretched laminar flame propagation velocity, unstretched laminar combustion velocity and Markstein length were obtained at various ratios of nitrogen to gas mixture. Combustion stability at various ratios of nitrogen to gas mixture was analyzed by analyzing the pictures of flame propagation. Furthermore, the effect of initial pressure on the flame propagation and combustion characteristics of methane/air mixed gas in gas explosion was analyzed. The results show that the unstretched laminar flame propagation velocity, the unstretched laminar combustion velocity, Markstein length, flame stability, and the maximum combustion pressure decrease distinctly with the increase of nitrogen fraction in the gas mixture. At the same ratios of nitrogen to gas mixture, Markstein length, unstretched laminar flame propagation velocity and unstretched laminar combustion velocity decrease and the maximum combustion pressure increase with the increase of initial pressure of the gas mixture. When nitrogen fraction in the gas mixture is over 20%, the flame will be unstable and is easy to exterminate.     

Nonlinear distribution characteristics of flame regions from methane–air explosions in coal tunnels

High temperature flame fronts generated in methane–air explosions are one of the major hazards in underground coal mines. However, the distribution laws of the flame region in explosions of this type and the factors influencing such explosions have rarely been studied. In this work, the commercial software package AutoReaGas, a finite-volume computational code for fluid dynamics suitable for gas explosion and blast problems, was used to carry out numerical simulations of a series of methane–air explosion processes for various initial premixed methane–air regions and cross-sectional areas in full-scale coal tunnels. Based on the simulated results and related experiments, the mechanism of flame propagation beyond the initial premixed methane–air region and the main factors influencing the flame region were analyzed. The precursor shock wave and turbulence disturb the initial unburned methane–air mixture and the pure air in front of the flame. The pure air and unburned mixture subsequently move backward along the axial direction and mix partially. The enlargement of the region containing methane induces that the range of the methane–air flame greatly exceeds the initial premixed methane–air region. The flame speed beyond the initial region is nonzero but appreciably lower than that in the original premixed methane–air region. The length of the initial premixed methane–air region has substantial influence on the size of the flame region, with the latter increasing exponentially as the former increases. For realistic coal tunnels, the cross-sectional tunnel area is not an important influencing factor in the flame region. These conclusions provide a theoretical framework in which to analyze accident causes and effectively mitigate loss arising from the repetition of similar accidents.     

初始温度和压力对排污空间甲烷-空气混合物爆燃特性影响的模拟研究

市政排污空间作为城市公共基础设施的重要组成部分，易积聚可燃气体形成爆炸性环境。结合排污空间的特殊环境条件，采用Fluidyn-MP多物理场数值模拟软件，建立了20 L球形爆炸罐分析模型，通过改变初始温度和初始压力，对排污空间甲烷-空气混合物爆燃特性及其变化规律进行模拟研究。结果表明:初始温度升高导致甲烷-空气混合物最大爆炸压力降低，缩短了到达最大爆炸压力的时间；初始压力增加导致最大爆炸压力急剧升高，并延长了到达最大爆炸压力的时间；最大爆炸压力对初始压力的敏感程度远大于初始温度的影响。此外，随着初始温度和初始压力的升高，爆炸火焰平均传播速度增加，而火焰传播速度对初始温度较敏感。     

水平管内不同煤质煤尘爆炸火焰传播特性实验研究

为研究水平管道空间不同煤质煤尘爆炸火焰传播特性，选取褐煤、长焰煤、不粘煤、气煤4种煤尘，对爆炸火焰焰峰特性、火焰加速传播特性、火焰传播距离与持续时间展开研究。研究结果表明:褐煤在500 ms内焰峰的形状由尖锐向平滑再向钝化不断演变，长焰煤与不粘煤在375 ms时焰峰前端出现明显焰体分离现象，分析认为这与管体冷壁效应、空间尺度效应及空间氧气消耗直接相关；气煤在375 ms时焰峰出现大面积火焰碎纹，说明气煤爆炸火焰猛烈传播的持续时间相对较短，整体爆炸强度相对较弱；褐煤与长焰煤爆炸火焰存在2次间断性加速，分析认为这与管体空间受限、常温管壁散热、局部助燃氧气瞬间不足等因素有关；褐煤在爆炸后400～600 ms内火焰2次加速完全，火焰传播距离达740 mm，明显大于长焰煤、不粘煤与气煤，说明低变质褐煤爆炸火焰持续时间更长，火焰传播距离更远且传播更剧烈；虽然气煤火焰最远传播距离比长焰煤大30 mm，但由于气煤火焰在375 ms左右出现大片火焰碎纹，因此气煤整体的爆炸强度小于长焰煤。     

CO2-超细水雾对瓦斯/煤尘爆炸抑制特性研究

为了解CO2-超细水雾对瓦斯/煤尘爆炸抑制特性，用自行搭建的实验系统，从超压、火焰传播速度和火焰结构3个方面研究了CO2-超细水雾形成的气液两相介质对9.5%瓦斯/煤尘复合体系爆炸的抑爆效果、影响因素与原因。研究结果表明:随着CO2体积分数和超细水雾质量浓度的增加，爆炸火焰最大传播速度、爆炸超压峰值均出现明显下降，火焰到达泄爆口时间显著延迟；尤其当CO2体积分数达到14%与超细水雾的共同抑爆效果凸显，瓦斯/煤尘复合体系爆炸超压的“震荡平台”消失，同时火焰结构呈现“整体孔隙化”。所得结论为煤矿井下高效防爆抑爆技术进行了完善和增强。     

Effect of flame propagation regime on pressure evolution of nano and micron PMMA dust explosions

Experiments using an open space dust explosion apparatus and a standard 20 L explosion apparatus on nano and micron polymethyl methacrylate dust explosions were conducted to reveal the differences in flame and pressure evolutions. Then the effect of combustion and flame propagation regimes on the explosion overpressure characteristics was discussed. The results showed that the flame propagation behavior, flame temperature distribution and ion current distribution all demonstrated the different flame structures for nano and micron dust explosions. The combustion and flame propagation of 100 nm and 30 μm PMMA dust clouds were mainly controlled by the heat transfer efficiency between the particles and external heat sources. Compared with the cluster diffusion dominant combustion of 30 μm dust flame, the premixed-gas dominant combustion of 100 nm dust flame determined a quicker pyrolysis and combustion reaction rate, a faster flame propagation velocity, a stronger combustion reaction intensity, a quicker heat release rate and a higher amount of released reaction heat, which resulted in an earlier pressure rise, a larger maximum overpressure and a higher explosion hazard class. The complex combustion and propagation regime of agglomerated particles strongly influenced the nano flame propagation and explosion pressure evolution characteristics, and limited the maximum overpressure.     

瓦斯爆炸引起沉积煤尘爆炸传播实验研究

运用井下大型实验巷道对瓦斯爆炸诱导沉积煤尘爆炸进行实验研究,并对几次实验结果进行对比分析。通过对爆炸压力以及火焰产生、发展、传播过程进行的分析,得出瓦斯爆炸引起沉积煤尘爆炸过程中压力波存在回传现象;在煤尘刚开始参与爆炸处,爆炸超压有一个较长的持续时间;爆炸火焰的传播速度在铺有煤尘段迅速上升,最后有一平缓的上升阶段,过了煤尘段开始下降;火焰区长度约为煤尘区长度的2倍等规律。实验研究发现的规律为有效的预防瓦斯煤尘爆炸事故提供了理论依据。     

瓦斯煤尘爆炸特性及传播规律研究进展

概要介绍国内外的瓦斯爆炸和瓦斯煤尘混合物爆炸特性及传播规律研究进展,瓦斯爆炸研究主要集中在瓦斯爆炸压力、火焰、温度等特征参数、不同障碍物对瓦斯爆炸压力、火焰传播的影响以及分岔、拐弯等不同形状管道内的传播规律,而瓦斯煤尘混合物爆炸研究主要集中在瓦斯对煤尘爆炸的最小点火能、爆炸下限、最大爆炸压力等爆炸特性及传播规律的影响。对不同研究人员采用的主要研究指标、手段、方法和研究结论进行综合评述,同时也对爆炸事故人员伤害模型在国内外的研究状况进行讨论,最后指出目前存在的主要问题和下一步的研究方向。     

Effects of particle characteristics on flame propagation behavior during organic dust explosions in a half-closed chamber

To reveal the effects of particle characteristics on the mechanisms of flame propagation during organic dust explosions clearly, three long chain monobasic alcohols which are solids at room temperature and have similar physical–chemical properties were chosen to carry out experiments in a half-closed small chamber. A high-speed video camera was used to record the flame propagation process and to obtain the direct light emission photographs. Flame temperature was detected by a fine thermocouple. Based on the experimental results above, analysis was conducted on flame propagation characteristics and temperature profiles of organic particle cloud. As a result, it was found that the particle materials, especially volatility, strongly affected the flame propagation behavior. Particle concentration also affects the combustion zone propagation process significantly. With increasing the particle concentration, the maximum temperature of the combustion zone increases at the lower concentration, reaches a maximum value, and then decreases at the higher concentration. The propagation velocity of the combustion zone has a linear relationship with the maximum temperature, which implies conductive heat transfer is dominant in the flame propagation process of the three different volatile dusts.     

甲烷煤尘耦合爆炸传播特性及伤害研究

为探究煤尘质量浓度对甲烷煤尘耦合爆炸传播特性及伤害距离的影响,自制长15 m的爆炸管道系统,用体积分数为7％甲烷分别与质量浓度为0、50、100和200 g/m3的煤尘进行耦合爆炸试验,并根据质量、动量和能量守恒理论推导出最大压力计算公式.结果 表明:不同质量浓度煤尘与甲烷耦合爆炸时,最大压力均随与爆源距离的增加呈现出...     

基于20L球形爆炸装置的甲烷煤尘混合爆炸实验

利用实验室自行设计的20L球形爆炸装置,对煤尘及甲烷煤尘混合物的爆炸特性进行了研究。结果表明:无论有无甲烷,煤尘的最大爆炸压力随煤尘浓度增加呈现先升高后降低的变化趋势,并且均在在煤尘浓度为600g/m3时均达到最大值。同时,甲烷的加入明显提高了煤尘最大爆炸压力值,而且随着甲烷浓度的增加,最大爆炸压力增幅先增加后降低,在甲烷5%时增幅最大。煤尘的爆炸持续时间随煤尘浓度增加呈现先降低后升高的特点,甲烷存在时有同样规律,但是有甲烷时爆炸持续时间明显降低,而且随着甲烷含量的增加,煤尘的爆炸持续时间降低幅度不断增加,在甲烷5%以后趋于稳定。实验结果对生产实践有一定的指导作用。     

Experimental investigation on explosion flame propagation of wood dust in a semi-closed tube

In order to explore flame propagation characteristics during wood dust explosions in a semi-closed tube, a high-speed camera, a thermal infrared imaging device and a pressure sensor were used in the study. Poplar dusts with different particle size distributions (0–50, 50–96 and 96–180 μm) were respectively placed in a Hartmann tube to mimic dust cloud explosions, and flame propagation behaviors such as flame propagation velocity, flame temperature and explosion pressure were detected and analyzed. According to the changes of flame shapes, flame propagations in wood dust explosions were divided into three stages including ignition, vertical propagation and free diffusion. Flame propagations for the two smaller particles were dominated by homogeneous combustion, while flame propagation for the largest particles was controlled by heterogeneous combustion, which had been confirmed by individual Damköhler number. All flame propagation velocities for different groups of wood particles in dust explosions were increased at first and then decreased with the augmentation of mass concentration. Flame temperatures and explosion pressures were almost similarly changed. Dust explosions in 50–96 μm wood particles were more intense than in the other two particles, of which the most severe explosion appeared at a mass concentration of 750 g/m³. Meanwhile, flame propagation velocity, flame propagation temperature and explosion pressure reached to the maximum values of 10.45 m/s, 1373 °C and 0.41 MPa. In addition, sensitive concentrations corresponding to the three groups of particles from small to large were 500, 750 and 1000 g/m³, separately, indicating that sensitive concentration in dust explosions of wood particles was elevated with the increase of particle size. Taken together, the finding demonstrated that particle size and mass concentration of wood dusts affected the occurrence and severity of dust explosions, which could provide guidance and reference for the identification, assessment and industrial safety management of wood dust explosions.     

Effects of hydrogen addition on propagation characteristics of premixed methane/air flames

An experimental study has been conducted to investigate the effects of hydrogen addition on the fundamental propagation characteristics of methane/air premixed flames at different equivalence ratios in a venting duct. The hydrogen fraction in the methane–hydrogen mixture was varied from 0 to 1 at equivalence ratios of 0.8, 1.0 and 1.2. The results indicate that the tendency towards flame instability increased with the fraction of hydrogen, and the premixed hydrogen/methane flame underwent a complex shape change with the increasing hydrogen fraction. The tulip flame only formed when the fraction of hydrogen ranged from 0 to 50% at an equivalence ratio of 0.8. It was also found that the flame front speed and the overpressure increased significantly with the hydrogen fraction. For all equivalence ratios, the stoichiometric flame (Φ = 1.0) has the shortest time of flame propagation and the maximum overpressure.