Remediation of PCB contaminated soils using iron nano-particles

In this study, iron nano-particles were used to remediate PCB contaminated soil and an attempt was made to maximize PCB destruction in each treatment step. The results show that nano-particles do aid in the dechlorination process and high PCB destruction efficiencies can be achieved. The destruction efficiency during the preliminary treatment (mixing of soil and iron nano-particles in water) can be increased by increasing the water temperature. The maximum thermal destruction (pyrolysis/combustion of soil after preliminary treatment) of soil-bound PCBs occurs at 300 degrees C in air. A minimum total PCB destruction efficiency of 95% can be achieved by this process. The effect of changing treatment parameters such as type of mixing, time of mixing and mixing conditions and application of other catalysts like iron oxide and V(2)O(5)/TiO(2) was also investigated. It was found that at 300 degrees C in air, iron oxide and V(2)O(5)/TiO(2) are also good catalysts for remediating PCB contaminated soils.     

Removal of PCBs in contaminated soils by means of chemical reduction and advanced oxidation processes

Although the chemical reduction and advanced oxidation processes have been widely used individually, very few studies have assessed the combined reduction/oxidation approach for soil remediation. In the present study, experiments were performed in spiked sand and historically contaminated soil by using four synthetic nanoparticles (Fe⁰, Fe/Ni, Fe₃O₄, Fe_3???x Ni _x O₄). These nanoparticles were tested firstly for reductive transformation of polychlorinated biphenyls (PCBs) and then employed as catalysts to promote chemical oxidation reactions (H₂O₂ or persulfate). Obtained results indicated that bimetallic nanoparticles Fe/Ni showed the highest efficiency in reduction of PCB28 and PCB118 in spiked sand (97 and 79 %, respectively), whereas magnetite (Fe₃O₄) exhibited a high catalytic stability during the combined reduction/oxidation approach. In chemical oxidation, persulfate showed higher PCB degradation extent than hydrogen peroxide. As expected, the degradation efficiency was found to be limited in historically contaminated soil, where only Fe⁰ and Fe/Ni particles exhibited reductive capability towards PCBs (13 and 18 %). In oxidation step, the highest degradation extents were obtained in presence of Fe⁰ and Fe/Ni (18–19 %). The increase in particle and oxidant doses improved the efficiency of treatment, but overall degradation extents did not exceed 30 %, suggesting that only a small part of PCBs in soil was available for reaction with catalyst and/or oxidant. The use of organic solvent or cyclodextrin to improve the PCB availability in soil did not enhance degradation efficiency, underscoring the strong impact of soil matrix. Moreover, a better PCB degradation was observed in sand spiked with extractable organic matter separated from contaminated soil. In contrast to fractions with higher particle size (250–500 and <500 μm), no PCB degradation was observed in the finest fraction (≤250 μm) having higher organic matter content. These findings may have important practical implications to promote successively reduction and oxidation reactions in soils and understand the impact of soil properties on remediation performance.     

Scavenging of BHCs and DDTs from soil by thermal desorption and solvent washing

Intensive remediation of abandoned former organochlorine pesticides (OCPs) manufacturing areas is necessary because the central and surrounding soils contaminated by OCPs are harmful to crop production and food safety. Organochlorine and its residues are persistent in environments and difficult to remove from contaminated soils due to their low solubility and higher sorption to the soils. We performed a comprehensive study on the remediation of OCPs-contaminated soils using thermal desorption technique and solvent washing approaches. The tested soil was thermally treated at 225, 325, 400, and 500 °C for 10, 20, 30, 45, 60, and 90 min, respectively. In addition, we tested soil washing with several organic solvents including n-alcohols and surfactants. The optimal ratio of soil/solvent was tested, and the recycling of used ethanol was investigated. Finally, activities of polyphenol oxidase (PPO), urease (URE), alkaline phosphatase, acid phosphatase (ACP), and invertase (INV) were assayed in the treated soils. The tested soil was thermally treated at 500 °C for 30 min, and the concentration of contaminants in soil was decreased from 3,115.77 to 0.33 mg kg^?1. The thermal desorption in soil was governed by the first-order kinetics model. For the chemical washing experiment, ethanol showed a higher efficiency than any other solvent. Using a 1:20 ratio of soil/solvent, the maximum removal of OCPs was achieved within 15 min. Under this condition, approximately 87 % of OCPs was removed from the soils. More than 90 % of ethanol in the spent wash fluid could be recovered. Activities of some enzymes in soils were increased after ethanol treatment. But ALP, ACP, and INV activities were decreased and PPO and URE showed slightly higher activities following remediation by thermal treatment. Both heating temperature and time were the key factors for thermal desorption of OCPs. The n-alcohol solvent showed higher removal of OCPs from soils than surfactants. The highly efficient removal of OCPs from soil was achieved using ethanol. More than 90 % of ethanol could be recovered and be reused following distillation. This study provides a cost-effective and highly efficient way to remediate the OCPs-contaminated soils.     

Formation pathways of polychlorinated dibenzofurans (PCDFs) in sediments contaminated with PCBs during the thermal desorption process

Thermal desorption has attracted considerable interest as a remediation technology for the removal of dioxins and polychlorinated biphenyls (PCBs) from contaminated soils and sediments. Although several research groups have confirmed that polychlorinated dibenzofurans (PCDFs) are formed from PCBs during the thermal desorption of sediments contaminated with PCB, the formation pathways remain poorly understood. Herein, thermal desorption has been used to develop a greater understanding of the formation pathways of PCDFs from sediments contaminated with PCBs. PCB decomposition experiments of sediments contaminated with PCBs were performed over 5 min at 450 °C with a gas composition of 10% O(2)/90% N(2), either in the absence (Run 1) or presence (Run 2-4) of one of three different (13)C(12)-labeled PCB individual standards. The results of Run 1 showed that 99.96% of PCBs and 98.40% of polychlorinated dibenzo-p-dioxins (PCDDs) in the treated sediments had decomposed, whereas the concentration levels of PCDFs had increased by a factor of 31. The addition of different (13)C(12)-labeled PCBs to the sediment sample yielded different (13)C(12)-PCDFs isomer patterns, with formation pathways including loss of ortho-Cl(2), loss of HCl involving a 2,3-chlorine shift, loss of ortho-H(2) and dechlorination.     

Bioremediation trial on aged PCB-polluted soils—a bench study in Iceland

Polychlorinated biphenyls (PCBs) pose a threat to the environment due to their high adsorption capacity to soil organic matter, stability and low reactivity, low water solubility, toxicity and ability to bioaccumulate. With Icelandic soils, research on contamination issues has been very limited and no data has been reported either on PCB degradation potential or rate. The goals of this research were to assess the bioavailability of aged PCBs in the soils of the old North Atlantic Treaty Organization facility in Keflavík, Iceland and to find the best biostimulation method to decrease the pollution. The effectiveness of different biostimulation additives (N fertiliser, white clover and pine needles) at different temperatures (10 and 30 °C) and oxygen levels (aerobic and anaerobic) were tested. PCB bioavailability to soil fauna was assessed with earthworms (Eisenia foetida). PCBs were bioavailable to earthworms (bioaccumulation factor 0.89 and 0.82 for earthworms in 12.5 ppm PCB soil and in 25 ppm PCB soil, respectively), with less chlorinated congeners showing higher bioaccumulation factors than highly chlorinated congeners. Biostimulation with pine needles at 10 °C under aerobic conditions resulted in nearly 38 % degradation of total PCBs after 2 months of incubation. Detection of the aerobic PCB degrading bphA gene supports the indigenous capability of the soils to aerobically degrade PCBs. Further research on field scale biostimulation trials with pine needles in cold environments is recommended in order to optimise the method for onsite remediation.     

In Memoriam

ABSTRACT

A feasibility study of polychlorinated biphenyl (PCB) removal from contaminated soils using microwave-generated steam (MGS) was performed. Initial experimental results show that MGS effectively removed PCBs from contaminated soil with an overall removal efficiency of greater than 98% at a steam-to-soil mass ratio of 3:1. Removal efficiency was found to be dependent upon the amount of steam employed, expressed as a mass ratio of steam applied to soil mass. Evaporation was identified as a major mechanism in removing PCBs from the soil. Rapid expansion and evaporation of pore water by microwave dielectric heating accelerated evaporation rates of PCB molecules. Increased solubility of PCBs into the heated aqueous phase is also hypothesized. Together these effects increase mass-transfer rates, thus enhancing removal of PCBs from the soil.     

Investigation of polychlorinated biphenyl removal from contaminated soil using microwave-generated steam

A feasibility study of polychlorinated biphenyl (PCB) removal from contaminated soils using microwave-generated steam (MGS) was performed. Initial experimental results show that MGS effectively removed PCBs from contaminated soil with an overall removal efficiency of greater than 98% at a steam-to-soil mass ratio of 3:1. Removal efficiency was found to be dependent upon the amount of steam employed, expressed as a mass ratio of steam applied to soil mass. Evaporation was identified as a major mechanism in removing PCBs from the soil. Rapid expansion and evaporation of pore water by microwave dielectric heating accelerated evaporation rates of PCB molecules. Increased solubility of PCBs into the heated aqueous phase is also hypothesized. Together these effects increase mass-transfer rates, thus enhancing removal of PCBs from the soil.     

Evaluation of B. subtilis SPB1 biosurfactants' potency for diesel-contaminated soil washing: optimization of oil desorption using Taguchi design

Low solubility of certain hydrophobic soil contaminants limits remediation process. Surface-active compounds can improve the solubility and removal of hydrophobic compounds from contaminated soils and, consequently, their biodegradation. Hence, this paper aims to study desorption efficiency of oil from soil of SPB1 lipopeptide biosurfactant. The effect of different physicochemical parameters on desorption potency was assessed. Taguchi experimental design method was applied in order to enhance the desorption capacity and establish the best washing parameters. Mobilization potency was compared to those of chemical surfactants under the newly defined conditions. Better desorption capacity was obtained using 0.1 % biosurfacatnt solution and the mobilization potency shows great tolerance to acidic and alkaline pH values and salinity. Results show an optimum value of oil removal from diesel-contaminated soil of about 87 %. The optimum washing conditions for surfactant solution volume, biosurfactant concentration, agitation speed, temperature, and time were found to be 12 ml/g of soil, 0.1 % biosurfactant, 200 rpm, 30 °C, and 24 h, respectively. The obtained results were compared to those of SDS and Tween 80 at the optimal conditions described above, and the study reveals an effectiveness of SPB1 biosurfactant comparable to the reported chemical emulsifiers. (1) The obtained findings suggest (a) the competence of Bacillus subtilis biosurfactant in promoting diesel desorption from soil towards chemical surfactants and (b) the applicability of this method in decontaminating crude oil-contaminated soil and, therefore, improving bioavailability of hydrophobic compounds. (2) The obtained findings also suggest the adequacy of Taguchi design in promoting process efficiency. Our findings suggest that preoptimized desorption process using microbial-derived emulsifier can contribute significantly to enhancement of hydrophobic pollutants' bioavailability. This study can be complemented with the investigation of potential role in improving the biodegradation of the diesel adsorbed to the soil.     

Properties of biochars from conventional and alternative feedstocks and their suitability for metal immobilization in industrial soil

In contaminated soils, excessive concentrations of metals and their high mobility pose a serious environmental risk. A suitable soil amendment can minimize the negative effect of metals in soil. This study investigated the effect of different biochars on metal (Cu, Pb, Zn) immobilization in industrial soil. Biochars produced at 300 and 600 °C from conventional (MS, maize silage; WP, wooden pellets) and alternative (SC, sewage sludge compost; DR, digestate residue) feedstocks were used as soil amendments at a dosage of 10 % (w/w). The type of feedstock and pyrolysis temperature affected the properties of the biochars and their ability to immobilize metal in soil. Compared to production at 300 °C, all biochars produced at 600 °C had higher pH (6.2–10.7), content of ash (7.2–69.0 %) and fixed carbon (21.1–56.7 %), but lower content of volatile matter (9.7–37.2 %). All biochars except DR biochar had lower dissolved organic carbon (DOC) content (1.4–2.3 g C/L) when made at 600 °C. Only MS and SC biochars had higher cation exchange capacity (25.2 and 44.7 cmol/kg, respectively) after charring at 600 °C. All biochars contained low concentrations of Cd, Cu, Ni, Pb and Zn; Cd was volatilized to the greatest extent during pyrolysis. Based on FTIR analysis and molar ratios of H/C and O/C, biochars had a greater degree of carbonization and aromaticity after charring at 600 °C. The efficiency of the biochars in metal immobilization depended mainly on their pH, ash content, and concentration of DOC. SC and DR biochars were more effective for Cu and Zn immobilization than MS and WP biochars, which makes them attractive options for large-scale soil amendment.     

Life cycle of PCBs and contamination of the environment and of food products from animal origin

This report gives a summary of the historic use, former management and current release of polychlorinated biphenyls (PCBs) in Germany and assesses the impact of the life cycle of PCBs on the contamination of the environment and of food products of animal origin. In Germany 60,000 t of PCBs were used in transformers, capacitors or as hydraulic oils. The use of PCB oils in these “closed applications”, has been banned in Germany in 2000. Thirty to 50% of these PCBs were not appropriately managed. In West Germany, 24,000 t of PCBs were used in open applications, mainly as additive (plasticiser, flame retardant) in sealants and paints in buildings and other construction. The continued use in open applications has not been banned, and in 2013, an estimated more than 12,000 t of PCBs were still present in buildings and other constructions. These open PCB applications continuously emit PCBs into the environment with an estimated release of 7–12 t per year. This amount is in agreement with deposition measurements (estimated to 18 t) and emission estimates for Switzerland. The atmospheric PCB releases still have an relevant impact on vegetation and livestock feed. In addition, PCBs in open applications on farms are still a sources of contamination for farmed animals. Furthermore, the historic production, use, recycling and disposal of PCBs have contaminated soils along the lifecycle. This legacy of contaminated soils and contaminated feed, individually or collectively, can lead to exceedance of maximum levels in food products from animals. In beef and chicken, soil levels of 5 ng PCB-TEQ/kg and for chicken with high soil exposure even 2 ng PCB-TEQ/kg can lead to exceedance of EU limits in meat and eggs. Areas at and around industries having produced or used or managed PCBs, or facilities and areas where PCBs were disposed need to be assessed in respect to potential contamination of food-producing animals. For a large share of impacted land, management measures applicable on farm level might be sufficient to continue with food production. Open PCB applications need to be inventoried and better managed. Other persistent and toxic chemicals used as alternatives to PCBs, e.g. short chain chlorinated paraffins (SCCPs), should be assessed in the life cycle for exposure of food-producing animals and humans.     

TiO2 photocatalytic degradation of PCBs in soil-water systems containing fluoro surfactant

Titanium dioxide-mediated photodegradation of Polychlorinated biphenyls (PCBs) in soil/aqueous systems with added fluorinated surfactant was investigated. PCBs can bind tightly to organic matter in the soil, especially in aged, contaminated soil. Experiments showed an effective PCB photocatalytic degradation in mixed systems of soil/clay with anionic fluorinated surfactant FC-143 and TiO2. The FC-143 surfactant is stable in this photochemical process. PCB degradation rates in samples followed the order: spiked clay > spiked soil > Hudson River bank soil. The results suggest that anionic fluorinated surfactant may form semimicelles and/or admicelles on the surface of positively charged TiO2. The hydrophobic surface of TiO2 can provide a nonpolar phase that acts as a partioning medium for hydrophobic PCBs. Therefore, PCBs in soil can be released to the semimicelle and/or admicelle on the TiO2 surface and are effectively photodegraded in a dispersion containing anionic fluorinated surfactant. The combination of surfactant extraction and photooxidation forms the basis for a novel two-stage process for the removal and destruction of PCBs from soil.     

Compound-specific isotopic and congener-specific analyses of polychlorinated biphenyl in the heat medium and rice oil of the Yusho incident

Compound-specific isotope analysis (CSIA) can be used to examine the source and transformation processes of organic pollutants in the environment. We performed a carbon stable isotope analysis of polychlorinated biphenyl (PCB) congeners in the PCB heat-transfer medium (heat medium) and the original Kanechlor-400 (KC-400, a commercial brand of PCBs) involved in the Yusho incident. The main purpose is to investigate whether isotope fractionation occurred in the rice oil deodorization process that caused the incident. The carbon isotope ratios (δ¹³C values) of the targeted PCB congeners ranged from ? 29.39 to ? 27.00‰ in the heat medium and from ? 28.77 to ? 27.05‰ in the original KC-400. No significant differences were found in the δ¹³C values, suggesting carbon isotope fractionation did not occur for the targeted PCB congeners in the heat medium when deodorization of rice oil occurred at temperatures above 200 °C. Furthermore, we also conducted a congener-specific analysis of 64 PCB congeners found in the heat medium and rice oil contaminated by it. The total PCB congener concentrations were 503 mg/g in the heat medium and 81 μg/g in the rice oil. The concentrations of the highly chlorinated congeners were significantly lower in the heat medium than in the original KC-400, and the compositional ratios of the lowly chlorinated congeners were relatively lower in the rice oil than in the heat medium. These results suggest that the PCB congener patterns gradually changed from that of the original KC-400 in the deodorization process and subsequent contamination into the rice oil. Thus, a combination of CSIA and congener-specific analysis is a new approach for investigating the changing PCB congener profiles in samples from the Yusho incident.     

Application of microwave irradiation in the removal of polychlorinated biphenyls from soil contaminated by capacitor oil

The applicability of microwave irradiation in the removal of polychlorinated biphenyls (PCBs) from the soil heavily contaminated by capacitor oil was studied. Granular activated carbon (GAC) was added into the soil as a microwave-absorbing material to rapidly increase the temperature of the reaction system. Effects of sodium hypophosphite (SHP) and iron powder (IP) as reductants on PCB removal, as well as the effects of water content in soil, microwave power and the amount of GAC added were investigated. The results indicated that in the presence of SHP and GAC, about 80% of PCBs in soil were effectively removed by 10 min microwave irradiation, and the further addition of IP could raise the average removal efficiency to a higher level, more than 95%. In the removal of PCBs with the microwave/GAC/IP/SHP system, an appropriate amount of water proved to be helpful in promoting the removal of PCBs from soil by steam distillation and in acting as a co-solvent of SHP and H-donor of IP.     

Value of biochars from Miscanthus x giganteus cultivated on contaminated soils to decrease the availability of metals in multicontaminated aqueous solutions

The objective of this study was to evaluate the sorption efficiency of eight biochars, made from Miscanthus x giganteus cultivated on contaminated agricultural soil, in aqueous solutions contaminated with metals alone or mixed with polycyclic aromatic hydrocarbons. These biochars were produced in different pyrolysis conditions (temperature, 400/600 °C; heating rate, 5/10 °C min⁻¹; duration, 45/90 min) and compared with an uncontaminated commercialized biochar made of wood. The physicochemical characterization of the Miscanthus biochars confirmed the impact of the pyrolysis on the biochar parameters with substantial differences between the biochars in terms of pH, cation exchange capacity, and specific surface area. The sorption experiment showed higher sorption efficiency of Cd, Pb, and Zn for the Miscanthus biochars produced at 600 °C compared with the biochars produced at 400 °C when the aqueous solutions were mono- or multicontaminated. Furthermore, the desorption study showed that the sorption process was largely irreversible. Therefore, the high sorption capacity of Miscanthus biochars and the low sorption reversibility confirmed that these biochars are a suitable sorbent for metals.

     

Why biota still accumulate high levels of PCB after removal of PCB contaminated sediments in a Norwegian fjord

Accumulation of polychlorinated biphenyls (PCBs) in blue mussels (Mytilus edulis) and semipermeable membrane devices (SPMDs) was still high after the removal of PCB contaminated sediments from a Norwegian fjord by dredging. The accumulation of low chlorinated PCB congeners with a low octanol water-partitioning coefficient (K_ow) in blue mussels and SPMDs was higher than for the highly chlorinated congeners with a high K_ow. The accumulation of low chlorinated congeners was also higher in a lightly contaminated area compared to a highly contaminated area. That dredging the contaminated sediments was unsuccessful in lowering PCB levels in the biota may be for the following reasons: (1) Due to the low solubility of PCBs in the water it is possible that a decrease in the sediment concentration of PCB would leave the water concentrations of PCB unchanged. (2) Removal of the fine organic sediments may also play an important role, since a seabed with coarse inorganic material has a lesser ability to bind PCB. (3) The dredging may whirl up fine contaminated particles that eventually settles on the seabed producing a thin contaminated sediment layer that determine the water concentration. (4) Bioaccumulation in blue mussels and in the SPMDs occurs mostly from PCB dissolved in the water column. Since the water concentration of PCB is unchanged by the dredging, the accumulation in SPMDs and mussels is the same as before dredging. Further monitoring need to be carried out to report the long-term effect of the dredging.     

Treatment of polychlorinated biphenyls in two surface soils using catalyzed H₂O₂ propagations

Two surface soils contaminated with polychlorinated biphenyls (PCBs) collected from Superfund sites in the New England region of the United States, Fletcher Paints and Merrimack Industrial Metals, were evaluated for field treatment at the bench level using catalyzed H₂O₂ propagations (CHP—modified Fenton’s reagent). The two soils were first evaluated for the potential for in situ treatment based on two criteria: (1) temperature (<40 °C after CHP reagent addition), and (2) hydrogen peroxide longevity (>24 h). In situ CHP remediation was more applicable to the Fletcher soil, while the Merrimack soil was better suited to ex situ treatment based on temperature increases and hydrogen peroxide lifetimes. Using the highest hydrogen peroxide concentrations appropriate for in situ treatment in each soil, PCB destruction was 94% in the Fletcher soil but only 48% in the Merrimack soil. However, 98% PCB destruction was achieved in the Merrimack soil using conditions more applicable to ex situ treatment (higher hydrogen peroxide concentrations with temperatures >40 °C). Analysis of degradation products by gas chromatography/mass spectroscopy showed no detectable chlorinated degradation products, suggesting that the products of PCB oxidation were rapidly dechlorinated and degraded. The results of this research document that the two PCB-contaminated soils studied can be effectively treated using aggressive CHP conditions, and that such a detailed bench study provides important information before implementing field treatment.     

Thermodynamic and kinetic studies of As(V) removal from water by zirconium oxide-coated marine sand

Arsenic contamination of groundwater is a major threat to human beings globally. Among various methods available for arsenic removal, adsorption is fast, inexpensive, selective, accurate, reproducible and eco-friendly in nature. The present paper describes removal of arsenate from water on zirconium oxide-coated sand (novel adsorbent). In the present work, zirconium oxide-coated sand was prepared and characterised by infrared and X-ray diffraction techniques. Batch experiments were performed to optimise different adsorption parameters such as initial arsenate concentration (100–1,000 μg/L), dose (1–8 g/L), pH of the solution (2–14), contact time (15–150 min.), and temperature (20, 30, 35 and 40 °C). The experimental data were analysed by Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherm models. Furthermore, thermodynamic and kinetic parameters were evaluated to know the mode of adsorption between ZrOCMS and As(V). The maximum removal of arsenic, 97 %, was achieved at initial arsenic concentration of 200 μg/L, after 75 min at dosage of 5.0 g/L, pH?7.0 and 27?±?2 °C. For 600 μg/L concentration, the maximum Langmuir monolayer adsorption capacity was found to be 270 μg/g at 35 °C. Kinetic modelling data indicated that adsorption process followed pseudo-second-order kinetics. The mechanism is controlled by liquid film diffusion model. Thermodynamic parameter, ΔH°, was ?57.782, while the values of ΔG° were ?9.460, ?12.183, ?13.343 and ?13.905 kJ/mol at 20, 30, 35 and 40 °C, respectively, suggesting exothermic and spontaneous nature of the process. The change in entropy, ΔS°?=??0.23 kJ/mol indicated that the entropy decreased due to adsorption of arsenate ion onto the solid adsorbent. The results indicated that the reported zirconium oxide-coated marine sand (ZrOCMS) was good adsorbent with 97 % removal capacity at 200 μg/L concentration. It is interesting to note that the permissible limit of arsenic as per World Health Organization is 10 μg/L, and in real situation, this low concentration can be achieved through this adsorbent. Besides, the adsorption capacity showed that this adsorbent may be used for the removal of arsenic from any natural water resource.     

Bench-scale testing of selected remediation alternatives for contaminated sediments

The Assessment and Remediation of Contaminated Sediments (ARCS) Program within the U.S. Environmental Protection Agency's Great Lakes National Program Office (GLNPO) contained a component for demonstrating and evaluating sediment remediation technologies. Toward this end, bench-scale tests of solvent extraction, thermal desorption, and wet air oxidation technologies were conducted. Contaminated sediments were tested from the Grand Calumet River, Indiana; Buffalo River, New York; Saginaw River, Michigan; and Ashtabula River, Ohio. The primary contaminants of concern in these sediments were polychlorinated biphenyls (PCBs) and polynuclear aromatic hydrocarbons (PAHs). The solvent extraction tests were conducted with sediments from the Grand Calumet, Buffalo, and Saginaw rivers. The thermal desorption studies were conducted with sediments from the Grand Calumet, Buffalo, and Ashtabula rivers. The wet air oxidation testing was performed with the Grand Calumet River sediment. Raw sediment contaminant concentrations ranged from 0.32-21.9 mg/kg dry mass for PCBs and 2.70-266 mg/kg dry mass for PAHs. PCB removal or destruction efficiencies ranged from approximately 6-99%. PAH removal or destruction efficiencies ranged from 65-99%. Mass balance closures ranged from 40-99% for solids; 59-139% for water; 29-3500% for oil; 16-129% for PCBs; and 69-3170% for PAHs.     

Effects of remediation train sequence on decontamination of heavy metal-contaminated soil containing mercury

When a contaminated site contains pollutants including both nonvolatile metals and Hg, one single remediation technology may not satisfactorily remove all contaminants. Therefore, in this study, chemical extraction and thermal treatment were combined as a remediation train to remove heavy metals, including Hg, from contaminated soil. A 0.2 M solution of ethylenediamine tetraacetic acid (EDTA) was shown to be the most effective reagent for extraction of considerable amounts of Cu, Pb, and Zn (>50%). Hg removal was ineffective using 0.2 M EDTA, but thermogravimetric analysis suggested that heating to 550°C with a heating rate of 5°C/min for a duration of 1 hr appeared to be an effective approach for Hg removal. With the employment of thermal treatment, up to 99% of Hg could be removed. However, executing thermal treatment prior to chemical extraction reduced the effectiveness of the subsequent EDTA extraction because nonvolatile heavy metals were immobilized in soil aggregates after the 550°C treatment. The remediation train of chemical extraction followed by thermal treatment appears to remediate soils that have been contaminated by many nonvolatile heavy metals and Hg.

ImplicationsA remediation train conjoining two or more techniques has been initialized to remove multiple metals. Better understandings of the impacts of treatment sequences, namely, which technique should be employed first on the soil properties and the decontamination efficiency, are in high demand. This study provides a strategy to remove multiple heavy metals including Hg from a contaminated soil. The interactions between thermal treatment and chemical extraction on repartitioning of heavy metals was revealed. The obtained results could offer an integrating strategy to remediate the soil contaminated with both heavy metals and volatile contaminants.     

Development of a new polyclonal antibody for the determination of polychlorinated biphenyls in indoor air by ic-ELISA

A new polyclonal antibody (pAb) was prepared and used for the determination of polychlorinated biphenyls (PCBs) in air samples to promote the application of immunoassay technology in the determination of PCBs. Three PCB congeners immunogen mixture was used to stimulate immune responses in rabbits. The specific pAb to PCBs was obtained and used to develop an indirect competitive enzyme-linked immunosorbent assay (ic-ELISA). A standard curve for Aroclor 1248 was prepared using concentrations ranging from 0.1 to 100 μg L^?1. The average IC₅₀ value was 16.21 μg L^?1 and the limit of detection at 10 % inhibition (IC₉₀) was 0.069 μg L^?1. The entire procedure was then evaluated using spiked air samples. The recoveries of Aroclor 1248 at various spiking levels in the air samples ranged from 84 to 113 %, with relative standard deviations of 3 to 6 %. Under optimum conditions, the cross-reactivity profiles of the assays were obtained using three selected congeners, four Aroclor products, and other structurally related compounds of PCBs. The assays were found to be highly specific for PCB congeners and Aroclors 1248 and 1242. The air samples were then analyzed using gas chromatography coupled with high-resolution mass spectrometry to confirm the ic-ELISA results. The attained results demonstrated that the proposed method was an effective and inexpensive technique for the PCBs determination in air samples.