Adsorption of copper and nickel on Na-bentonite

The removal of copper and nickel from aqueous solution on the Na-bentonite has been studied under static conditions. Experiments were carried out as a function of solution pH, dosage of Na-bentonite, contact time and temperature. The adsorption equilibrium for nickel and copper onto Na-bentonite is reached in 200 min. The adsorption of copper and nickel is pH dependent in the pH range 2–9. The kinetic process of adsorption can be described by the pseudo-second-order kinetic equation excellently and the adsorption isotherm be fitted to the Langmuir model by means of regression analyses very well. The adsorption capacities follow the order of Cu²⁺ > Ni²⁺ in single-component systems and competitive adsorption capacities in order decreasing is Cu²⁺ > Ni²⁺ in binary-component systems.     

Characterization of heavy metals in fly ash from municipal solid waste incinerators in Shanghai

This study aims to develop a methodology for analysis of characteristics of heavy metals in MSWI fly ash. It performed analysis of composition of heavy metals, leaching toxicity, leaching behavior as a function of pH, specification distribution and corresponding mineral components of residue derived from each step of the sequential extraction. It is found that content of heavy metals follows the sequence of Zn > Pb > Cu > Cr > As > Ni > Cd approximately Hg in both plants, and that total heavy metals account for less than 1% by mass of fly ash. Major hazardous heavy metals in fly ash are As, Cd, Hg, Pb and Zn, whose leaching ratios exceed the limit value described in hazardous waste identification standard. Measured leaching results of Cu, Pb and Zn are essentially consistent with the simulated results at pH between 0 and 13. Content of calcium-silicates, alumino-silicates and glass phases in residue derived from sequential extraction procedure increases steadily from the first step to the fifth step of the sequential extraction procedure. Cu, As, Cr, Hg, Cd, and Ni, relatively stable under strong basic conditions, can be leached out under strong acidic conditions, while Zn and Pb tend to be leached out under both strong acidic and basic conditions.     

pH-conditioning for simultaneous removal of arsenic and iron ions from groundwater

The effects of some commonly used pH conditioners, viz., lime, banana ash, the carbonate and the bicarbonate of sodium and potassium and their binary mixture, on simultaneous removal of arsenic and iron ions from water have been studied. KHCO₃ has been found to be the most suitable pH conditioner for the purpose. About 80 mg/L KHCO₃ can remove both arsenate and iron ions from initial 250 μg/L and 20 mg/L to below their respective guideline values of the WHO for drinking water, retaining the final pH in the acceptable range for drinking. The simultaneous removal of arsenate and iron by the pH-conditioners decreases in the order: Lime > KHCO₃ > NaHCO₃ > K₂CO₃ > Na₂CO₃ > ash. However, lime requires post-treatment correction of highly alkaline pH. The arsenate ion is removed predominantly through goethite or ferrihydrite in the presence of the bicarbonates and through ferric hydroxide in the presence of the more alkaline pH-conditioners. KHCO₃ is more advantageous over the more basic substances including NaHCO₃, because with it, one not only needs the smallest dose but also can avoid careful adjustment of the dose for regulating the initial and the final pH. The paper clearly demonstrates the potential of KHCO₃ to substitute the currently used pH-conditioners, viz., ash, lime and NaHCO₃ for simultaneous removal of arsenate and iron ions.     

Biosorption of zinc(II) on rapeseed waste: Equilibrium studies and thermogravimetric investigations

The removal of heavy metals from aqueous effluents so as to avoid their toxic, bioaccumulation and biomagnification effects to humans and environment is usually realized by means of physical, chemical treatment, and biological processes. The aim of this study is to evaluate the potential of rapeseed waste from biodiesel production as a biosorbent for Zn(II) ions.The ability of the rapeseed waste for Zn(II) biosorption exhibited a maximum at pH 4.5–5. The removal efficiency of Zn(II) from solution with an initial concentration of 72 mg L⁻¹ varied from 39% to 89% for an increase of the rapeseed waste dose from 2 to 30 g L⁻¹. The amount of Zn(II) retained on the tested rapeseed increased with increasing metal ion concentration, but the Zn(II) sorption percentage decreased. The equilibrium data are fitted to the Langmuir isotherm better than to the Freundlich isotherm. The kinetics of Zn(II) biosorption process follows a pseudo-second order model. The thermal stability of the rapeseed before and after Zn(II) biosorption was studied by thermogravimetric analysis. It was found that the zinc loaded rapeseed exhibits a better initial thermal stability than the original rapeseed, presumably due to the cross linking generated by the intermolecular complexation of Zn(II) ions. In both cases, the thermal decomposition takes place according to some reassembling kinetic models, in two phases with order n reactions. The results of this study strongly suggest the possibility to use rapeseed as an effective biosorbent for Zn(II) ions removal from aqueous effluents (municipal/industrial wastewaters).     

Investigation of affecting parameters on treating high-strength compost leachate in a hybrid EGSB and fixed-bed reactor followed by electrocoagulation–flotation process

In this research, treatability of high-load compost leachate in a hybrid expanded granular sludge bed (EGSB) and fixed-bed (FB) bioreactor followed by electrocoagulation–flotation (ECF) system was examined. The operational factors in EGSB–FB were influent chemical oxygen demand (COD), hydraulic retention time (HRT) and COD/nitrogen ratio (COD/N). And, their interactive effects on the efficiency of COD removal and biogas production rate (BPR) as responses were analyzed and correlated by response surface methodology (RSM). The optimum conditions of the hybrid EGSB–FB reactor were acquired at COD = 7800 mg/L, HRT = 35 h, COD/N = 70, in which COD removal efficiency was 83% and BPR 94 mL/h. The amount of confidence interval was 95%. COD (relevant coefficient = 9.8) and HRT (relevant coefficient = −24) were resulted respectively as the most effective parameters on COD removal and BPR. Yet, COD/N parameter imposed negative effect on COD removal and BPR in values less than about 100. The outcomes indicated that operated ECF as post-treatment in constant conditions (electrolysis time = 75 min, electrodes distance = 3 cm, voltage = 20 V) successfully satisfied discharge criteria in the most part of experimental domains.     

Zero valent nano-sized iron/clinoptilolite modified with zero valent copper for reductive nitrate removal

Nitrates constitute one of the main toxic contaminants of groundwater. On the other hand, groundwater may be considered anoxic (oxygen concentration less than 9 μg L^?1). This fact justifies the use of nano zero valent metals for nitrate removal. In such conditions, zero valent metals are quite stable against oxidation due to the very low level of dissolved oxygen concentration. It has been shown that the performance of zero valent iron coated clinoptilolite zeolite for the reduction of nitrate anion in un-buffered conditions may be enhanced by coating small amounts of Cu⁰ onto the freshly prepared Fe⁰/zeolite composite. An optimum loading of Cu⁰ exists for which the rate of nitrate removal is maximal. For this optimal composition, the nitrite anion production curve with time passes through a maximum. Nitrite production, however, is slightly higher for the Cu modified zeolite. It has been shown that the nitrate removal process is only slightly dependent on the initial solution pH. In the temperature range of 20–60 °C, the process is controlled by both the liquid phase mass transfer and intrinsic reaction rate resistances. FESEM analysis of the zero valent metal/zeolite composite showed that upon the metal reduction reaction, an egg-shell distribution of zero valent metal in the zeolite agglomerate particle is produced.     

Degradation of Rhodamine B by an electrochemical ozone generating system consist of a Ti anode coated with nanocomposite of Sn–Sb–Ni oxide

An ozonation process was performed using a recycled electrochemical ozone generator system. A titanium based electrode, coated with nanocomposite of Sn–Sb–Ni was applied as anode in a laboratory-made electrochemical reactor. A constant flow rate of 192 mg/h of generated ozone was entered to an ozonation reactor to contact with a typical target pollutant, i.e., Rhodamine B (Rh.B) molecules in aqueous solution. Four operational parameters such as: initial dye concentration, pH, temperature and the contact time were evaluated for the ozonation process. Experimental findings revealed that for a solution of 8 mg/L of the dye, the degradation efficiency could reach to 99.5% after 30 min at pH 3.7 and temperature of 45 °C as the optimum conditions. Kinetic studies showed that a second order equation can describe the ozonation adequately well under different temperatures. Also, considering to the importance of process simulation, a three-layered feed forward back propagation artificial neural network model was developed. Sensitivity analysis indicated order of the operational parameter's relative importance on the model output as: time ≫ pH > Rh . B initial concentration > temperature.     

Artificial neural network modelling of As(III) removal from water by novel hybrid material

The present study reported a method for removal of As(III) from water solution by a novel hybrid material (Ce-HAHCl). The hybrid material was synthesized by sol–gel method and was characterized by XRD, FTIR, SEM–EDS and TGA–DTA. Batch adsorption experiments were conducted as a function of different variables like adsorbent dose, pH, contact time, agitation speed, initial concentration and temperature. The experimental studies revealed that maximum removal percentage is 98.85 at optimum condition: pH = 5.0, agitation speed = 180 rpm, temperature = 60 °C and contact time = 80 min using 9 g L⁻¹ of adsorbent dose for initial As(III) concentration of 10 mg L⁻¹. Using adsorbent dose of 10 g L⁻¹, the maximum removal percentage remains same with initial As(III) concentration of 25 mg L⁻¹ (or 50 mg L⁻¹). The maximum adsorption capacity of the material is found to be 182.6 mg g⁻¹. Subsequently, the experimental results are used for developing a valid model based on back propagation (BP) learning algorithm with artificial neural networking (BP-ANN) for prediction of removal efficiency. The adequacy of the model (BP-ANN) is checked by value of the absolute relative percentage error (0.293) and correlation coefficient (R² = 0.975). Comparison of experimental and predictive model results show that the model can predict the adsorption efficiency with acceptable accuracy.     

Removal of toluene vapour from air stream using a biofilter packed with polyurethane foam

Biodegradation of toluene vapour was investigated for 168 days in a polyurethane packed biofilter inoculated with a mixed microbial population. Biofilter consisted of five square cross-section modular units each of size 0.16 m × 0.16 m × 0.20 m and filled with the polyurethane foam cubes up to a height of 0.15 m. Inlet concentration of toluene was varied from 0.04 to 2.5 g m^?3 and the volumetric flow rate of toluene loaded air from 0.06 to 0.90 m³ h^?1.Depending upon initial loading rates, removal efficiency ranging from 68.2 to 99.9% and elimination capacity ranging from 10.85 to 90.48 g h^?1 m^?3 were observed during steady state operations. More than 90% removal efficiency was observed up to an inlet loading rate of 76.3 g h^?1 m^?3. High carbon recovery (>90%) indicated effective biodegradation in the bed. Low variation of pH (7.2–8.8) and pressure drop (45.8–76.3 Pa) was observed. The stability of the biomass was evident from the fast response of the biofilter to shutdown and restartup.     

An explosion of a tank car carrying waste hydrogen peroxide

On the Metropolitan Expressway in Tokyo, a tank car exploded because it was carrying hydrogen peroxide (H₂O₂) in a compartment in which copper chloride (CuCl₂) remained. Although the main cause of the accident was trivial, the background on the accident suggested that an induction period in the reaction led to a mistake. This report describes the experimental investigation of the catalytic ability of CuCl₂, and comparing it with two other copper(II) compounds (nitrate: Cu(NO₃)₂; and copper sulfate: CuSO₄) and three iron(III) compounds (chloride: FeCl₃; nitrate: Fe(NO₃)₃; and sulfate: Fe₂(SO₄)₃).The experiments were performed using a reaction calorimeter. During the experiments at 35 °C, 2×10⁻⁵ mol of copper compounds slowly reacted with H₂O₂ and generated a precipitate. The iron compounds allowed the hydrogen peroxide to violently decompose. A 1×10⁻⁴ mol solution of CuCl₂, however, produced a violent decomposition at 35 °C. At 15 °C, a moderate heat release occurred.Based on these results, the concentration and temperature dependence of the catalytic ability of CuCl₂ were postulated to contribute to the induction period observed in the accident.     

Biohydrogen production using waste activated sludge as a substrate from fructose-processing wastewater treatment

Biohydrogen production by dark fermentation in a series of batch tests under different environmental control conditions was evaluated to determine the optimal initial cultivation pH and temperature for a continuous-flow kinetic test to validate the kinetic model system. The waste activated sludge (WAS) from fructose-processing manufacturing was used as the model substrate for biohydrogen production. The batch experiments for biohydrogen production were conducted in a 6 l bioreactor. Fifteen batch kinetic tests were investigated when pH was controlled at 6, 7, 8 and 9 as well as the temperature was controlled at 37 °C, 45 °C and 55 °C, respectively. The experimental results indicated that the optimal operational condition for hydrogen production occurred while pH was 7 and temperature was 55 °C with the highest hydrogen production of 7.8 mmol. The optimal recovery time for hydrogen was 25 h in the batch experiments. Furthermore, the kinetic test of biohydrogen production was performed by anaerobic mixed microbial culture in the continuous-flow experiment when pH and temperature was maintained at 7 and 55 °C. Approximately 60% and 7% of substrate solution was converted into acetate and hydrogen, respectively, at the steady state. Roughly only 0.77% and 2.7% of substrate solution was converted into propionate and butyrate, respectively, at a steady-state condition. The experimental and modeling approaches presented in this study could be employed for the design of pilot-scale and full-scale anaerobic biohydrogen fermentors using food-processing waste activated sludge (WAS) as a substrate solution.     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Biosorption of Co(II) ions from aqueous solution using Chrysanthemum indicum: Kinetics,equilibrium and thermodynamics

The present study investigates the adsorption potential of Chrysanthemum indicum flower in its raw (CIF-R) and biochar (CIF-BC) form for the removal of cobalt ions from aqueous solution. The adsorbents were characterized for their surface area using BET analysis, surface morphology and elemental composition with SEM-EDAX and for the presence of functional groups by FTIR analysis. Batch adsorption experiments were carried out to evaluate the effect of process parameters, viz. pH, adsorbent dosage, initial metal ion concentration, contact time, stirring speed, presence of interfering ions and temperature on the adsorption of Co(II) ion using both the adsorbents. The optimum conditions for maximum removal of Co(II) ion was ascertained to be pH 5 for both adsorbents, adsorbent dose of 4 g/L and 3 g/L, equilibrium time of 60 min and 45 min, respectively, for CIF-R and CIF-BC. The maximum adsorption capacity of CIF-R and CIF-BC was found to be 14.84 mg/g and 45.44 mg/g, respectively, for the removal of Co(II) ion. The mechanism of adsorption was studied using different models of adsorption kinetics, isotherms and thermodynamics. It was inferred that Co(II) adsorption on both CIF-R and CIF-BC followed pseudo-second order kinetics and Langmuir isotherm model with the process being spontaneous and endothermic in nature.     

An improved method of removal for high concentrations of NO by electro-scrubbing process

In the Ag(II)/Ag(I) redox mediator integrated scrubber system, NO reacts with the Ag(II) ions produced by the electrochemical oxidation of Ag(I) in an electrochemical cell present in the scrubbing solution (aqueous HNO₃ acid) to form NO₂. This NO₂ is then absorbed into the scrubbing solution and degraded to nitrate. Numerous experimental runs were carried out to evaluate the feasibility of the integrated system to treat industrial waste gases containing high NO_x levels. The results showed that the levels of NO and NO_x removal increased with increasing Ag(II) loading and contact time. Under optimized conditions, 93.5% and 73.3% of the NO and NO_x, respectively, were removed by a single stage gas scrubber with 1.62 g L^?1 Ag(II) operating at 25 °C and atmospheric pressure.     

Evaluation of membrane bioreactor for hypersaline oily wastewater treatment

Produced water is a significant waste stream generated in association with oil and gas production. It contains high concentrations of hydrocarbon constituents and different salts. In this study, a membrane sequencing batch reactor (MSBR) was used to treat synthetic and real produced water. The MSBR was evaluated in terms of biodegradation of hydrocarbons in the synthetic produced water with various organic loading rates (OLR) (0.281, 0.563, 1.124, 2.248, and 3.372 kg COD/(m³ day)), cycle time (12, 24, and 48 h), and membrane performance. The effects of salt concentrations at different total dissolved solids (TDS) (35,000, 50,000, 100,000, 150,000, 200,000, and 250,000 mg/L) on biological treatment of the pollutants in the synthetic and real wastewater were studied. At an OLR of 1.124 kg COD/(m³ day), an HRT of 48 h and TDS of 35,000 mg/L, removal efficiencies of 97.5%, 97.2%, and 98.9% of COD, total organic carbon (TOC), and oil and grease (O&G), respectively were achieved. For the real produced water, removal rates of 86.2%, 90.8%, and 90% were obtained for the same conditions. However, with increasing salt content, the COD-removal efficiencies of the synthetic and real produced water were reduced to 90.4% and 17.7%, respectively at the highest TDS.     

Experimental study of the characteristics of solid fuel from fry-dried swine excreta

Swine excreta were dried by boiling via immersion in hot oil. In this method, moisture in the excreta is replaced with oil or evaporated by turbulent heat transfer in high-temperature oil. The dried excreta can be used in an incinerator like low-rank coal or solid fuel. Refined waste oil and B–C heavy oil were used for drying. Drying for 8 min at 150 °C reduced the water content of raw excreta from 78.90 wt.% to 1.56 wt.% (refined waste oil) or 1.62 wt.% (B–C heavy oil) and that of digested excreta from 79.58 wt.% to 3.40 wt.% (refined waste oil) or 3.48 wt.% (B–C heavy oil). The low heating values of the raw and digested excreta were 422 kJ/kg and ?2,713 kJ/kg, respectively, before drying and 27,842–28,169 kJ/kg and 14,394–14,905 kJ/kg, respectively, after drying. A heavy metal analysis did not detect Hg, Pb, Cd, As, and Cr in the dried excreta, but Al, Cu, and Zn, which occur in the feed formula, were detected. Thermogravimetric analysis before and after drying revealed that emission of volatiles and combustion of volatiles and fixed carbon occurred at temperatures of 250–500 °C when air was used as the transfer gas.     

Velocity and number density profiles of particles across upward and downward flame propagating through iron particle clouds

Behaviors of particles across upward and downward flame propagating through iron particle clouds have been recorded on photomicrographs by using a high-speed video camera with a microscopic optical system. The velocity profiles of iron particles across flames were measured by using the high-speed photomicrographs, and the number density profiles of iron particles near the flames were calculated by using the velocity profiles. It is shown that the number density of iron particles changes in the range of x smaller than 11.0 mm, where x is the distance from the leading edge of the combustion zone. The number density increases with the decrease of x in the range 0<x<11.0 mm, reaches a maximum at leading edge of the combustion zone, and then decreases. For upward propagating flame, the maximum value of the number density is about 3.5 times larger than that at the region far ahead of the flame (x>10.0 mm), however, for downward propagating flame, it is only 2.3 times larger than that at the region far ahead of the flame.     

Kinetics of nitrate reductive denitrification by nanoscale zero-valent iron

Nanoscale zero-valent iron (Fe⁰) was synthesized for nitrate denitrification. The reduction efficiency of nitrate decreased quickly with increasing initial pH value, increased considerably with the increasing dosage of nanoscale Fe⁰, and did not vary much with initial nitrate concentrations changing from 20 to 50 mg l^?1 when the excessive amount of nanoscale Fe⁰ was utilized. With reductive denitrification of nitrate by nanoscale Fe⁰, the removal rate of nitrate reached 96.4% in 30 min with nanoscale Fe⁰ dosage of 1.0 g l^?1 and pH_in 6.7, and more than 85% of the nitrate was transformed into ammonia. Kinetics analysis in batch studies demonstrates that the denitrification of nitrate by nanoscale Fe⁰ involves reaction on the metal surface, which fits well the pseudo-first order reaction with respect to nitrate concentration. The observed reaction rate constant of reductive denitrification of nitrate was determined to be 0.086 min^?1 with a nanoscale Fe⁰ dosage of 1.0 g l^?1 and pH_in 6.7. Fast and highly effective denitrification can be achieved by nanoscale Fe⁰ compared with commercial Fe⁰ powder, this is due to the extremely high surface area and high reactivity for nanoscale Fe⁰, which can enhance the denitrification efficiencies remarkably.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Association between safety leading indicators and safety climate levels

ObjectivesThe aim of this study was to evaluate the association of leading indicators for occupational health and safety, particularly safety inspections and non-compliances, with safety climate levels.MethodsNordic Occupational Safety Climate Assessment Questionnaire was employed to evaluate safety climate in cross-sectional design. The geographically diverse population of the inspection body made it possible to conduct the survey across 10 provinces in Iran. 89 completed questionnaires were obtained with a response rate of 47%. Except for management safety justice, the internal consistency of other six dimensions was found to be acceptable (α ≥ 0.7).ResultsMean scores of dimensions ranged from 3.50 in trust in the efficacy of safety systems (SD = 0.38) to 2.98 in workers' safety priority and risk non-acceptance (SD = 0.47). Tukey HSD tests indicated a statistically significant difference of mean scores among groups undergoing different number of safety inspections and those receiving different number of non-compliances (p < 0.05), with no significant differences based on safety training man-hours and sessions (p > 0.05). Spearman's rank-order correlation showed no relationship between work experience and number of non-compliances (correlation coefficient = − 0.04, p > 0.05) and between safety training man-hours and number of non-compliances (correlation coefficient = − 0.15, p > 0.05).ConclusionsOur results indicate that safety climate levels are influenced by number of safety inspections and the resultant non-compliances.Practical applicationsFindings suggest that safety non-compliances detected as a result of conducting safety inspections could be used to monitor the safety climate state. Establishing plans to conduct scheduled safety inspections and recording findings in the form of safety non-compliance and monitoring their trend could be used to monitor levels of safety climate.