Mesoporous simonkolleite–TiO2 nanostructured composite for simultaneous photocatalytic hydrogen production and dye decontamination

In the present work, mesoporous simonkolleite–TiO₂ composite was prepared with sol–gel method. The composite photocatalysts were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), and Raman spectroscopy. Also, surface area and particle size were analyzed using BET equation. The photocatalytic hydrogen production with simultaneous decolorization of Remazole Red (F3B) dye was investigated over TiO₂ and simonkolleite–TiO₂ composite under UV–vis light irradiation. It was worthy to be noted that the rate of hydrogen production over simonkolleite–TiO₂ is higher that produced over TiO₂. The maximum amount of photocatalytic-produced hydrogen was 2.1 mmol and 3.3 mmol within 240 min using TiO₂ and simonkolleite–TiO₂ composite, respectively. The specific production rate of hydrogen from photocatalytic conversion of dye was calculated. Improvement of apparent quantum yield (22.07%) after 5 h was achieved upon addition of simonkolleite to TiO₂. This high apparent quantum yield proves that the system proposed in this study could be a hopeful approach toward using sunlight energy as outlook energy source. The obtained results suggested that a new process for H₂ production from wastewater could be achieved. The process also provides a method for degradation of organic pollutants with simultaneous H₂ production.     

Preparation of iodine doped titanium dioxide to photodegrade aqueous bisphenol A under visible light

Highly photoactive iodine-doped titanium dioxide (I-doped TiO₂) photocatalysts were synthesized to degrade aqueous bisphenol A (BPA) under irradiation by visible light and sunlight. The band gap energies of TiO₂ and I-doped TiO₂ (I/Ti mole ratio = 0.5%) were 3.01 and 3.04, and the BPA photodegradation rate constants were 1.61, and 5.11 h⁻¹, respectively. The most probable reaction mechanism was proposed to involve IO₄⁻ and IO₃⁻ as electron acceptors that generate an inductive effect, increasing the photocatalytic efficiency of TiO₂. Results indicated that I-doped TiO₂ not only acted favorably as a photocatalyst, but also exhibited considerable mineralization effects. In addition, a recycling test after ten experiments demonstrated the stability and reusability of the photocatalyst.     

Refinery wastewater degradation with titanium dioxide,zinc oxide,and hydrogen peroxide in a photocatalytic reactor

This paper presents the photo-catalytic degradation of real refinery wastewater from National Refinery Limited (NRL) in Karachi, Pakistan, using TiO₂, ZnO, and H₂O₂. The pretreatment of the refinery effluent was carried out on site and pretreated samples were tested at 32–37 °C in a stirrer bath reactor by using ultra-violet photo oxidation process. The degradation of wastewater was measured as a change in initial chemical oxygen demand (COD) and with time. Optimal conditions were obtained for catalyst type, and pH. The titanium dioxide proved to be very effective catalysts in photo-catalytic degradation of real refinery wastewater. The maximum degradation achieved was 40.68% by using TiO₂ at 37 °C and pH of 4, within 120 min of irradiations. When TiO₂ was combined with H₂O₂ the degradation decreased to 25.35%. A higher reaction rate was found for titanium dioxide. The results indicate that for real refinery wastewater, TiO₂ is comparatively more effective than ZnO and H₂O₂. The experiments indicated that first-order kinetics can successfully describe the photo-catalytic reaction. The ANOVA results for the model showed satisfactory and reasonable adjustment of the second-order regression model with the experimental data. The ANOVA results also showed that pH is significant than reaction time and catalyst dosage of TiO₂; and in case of ZnO, reaction time is significant than pH and catalyst dosage. This study proves that real refinery wastewater reacts differently than synthetic refinery wastewater, oil field produced water or oil water industrial effluent.     

Disintegration of waste activated sludge by different applications of Fenton process

Oxidative disintegration of municipal waste activated sludge (WAS) using conventional Fenton (Fe²⁺ + H₂O₂, CFP) and Fenton type (Fe⁰ + H₂O₂, FTP) processes was investigated and compared in terms of the efficiency of sludge disintegration and enhancement of anaerobic biodegradability. The influences of different operational variables namely sludge pH, initial concentration of Fe²⁺ or Fe⁰, and H₂O₂ were studied in detail. The optimum conditions have been found as catalyst iron dosage = 4 g/kg TS, H₂O₂ dosage = 40 g/kg TS and pH = 3 within 1 h oxidation period for both CFP and FTP. Kinetics studies were performed under optimal conditions. It was determined that the sludge disintegration was happened in two stages by both processes: rapid and subsequent slow disintegration stages and rapid sludge disintegration stage can be described by a zero-order kinetic model. The effects of oxidative sludge disintegration under the optimum conditions on anaerobic digestion were experienced with biochemical methane potential (BMP) assay in batch anaerobic reactors. Total methane production in the CFP and FTP pre-treated reactors increased by 26.9% and 38.0%, relative to the untreated reactor (digested the raw WAS). Furthermore, the total chemical oxygen demand reductions in the pre-treated reactors were improved as well.     

Decolorization and degradation of acid dye with immobilized titania nanoparticles

This paper addresses the decolorization and degradation of acid dye by a heterogeneous photocatalytic process using immobilized nano-sized TiO₂ particles as the photocatalyst. Sackcloth fiber was used as a support to immobilize the nano-sized TiO₂ photocatalyst. The structural properties of the immobilized photocatalyst were characterized by XRD, SEM and EDX. UV–Vis absorption spectroscopy and the measurement of the chemical oxygen demand (COD) were also used for the process performance studies. The XRD results did not show significant changes in the structure of P25 as a consequence of the immobilization procedure. The formation of titania crystallites in the sackcloth fiber was confirmed by SEM/EDX. The photocatalytic activities of TiO₂-coated sackcloth fiber catalyst were evaluated using Acid Black 26 as a model organic contaminant and using UV-A radiation. Experimental results showed that after 60 min, the degradation of Acid Black 26 with the immobilized TiO₂ particles was higher than that with plain TiO₂. Based on the COD results, after 3 h, the TiO₂-coated sackcloth fiber effectively decomposed all of the organic compounds present in dye solution under the studied experimental conditions. The effects of the oxidant H₂O₂, initial dye concentration and pH on the photocatalytic degradation were also investigated. The presence of CO₃^2? as a dissolved inorganic anion had the highest inhibitory effect on the decolorization of the dye, when compared with the other anions investigated. Kinetics analysis indicates that the photocatalytic decolorization rate of Acid Black 26 can be described by a pseudo-first-order model.     

Growing Carbon Nanotube on Aluminum Oxides: An Inherently Safe Approach for Environmental Applications

Using micron-sized Al₂O₃ particles as carriers to grow carbon nanotubes (CNTs) under 700°C atmosphere of methane and hydrogen after pre-planted catalysts of Fe–Ni nanoparticles, those composite CNTs (CCNTs) have demonstrated several unique properties compared to CNTs—medium specific surface area and zeta potential, high adsorption capacity for metal ions, high recovery rate by acids, low decomposition heat for exothermal reaction, and so on. The adsorption behaviours of Pb²⁺, Cu²⁺ and Cd²⁺ in aqueous solutions by CCNTs are in good agreement with the Langmuir adsorption isotherm and second order kinetic model with maximum individual adsorption capacities of 67.11, 26.59 and 8.89 mg g⁻¹. The individual and competitive adsorption behaviours indicated that the preference order of adsorption were Pb²⁺ > Cu²⁺ > Cd²⁺ for aluminum oxides, activated carbon, commercial CNTs, and CCNTs as well as other researchers’ CNTs. We suggest that future development of CNTs to combine with metals and/or other materials, such as TiO₂, should consider attached to carriers or surface in order to avoid concerns on environment, health and safety. Thus, growing CNTs on Al₂O₃ particles to form CCNTs is an inherently safe approach for many promising environmental applications.     

An Experimental Study on Pyrolysis of Biomass

In this study, pyrolysis of sugarcane bagasse was performed in fixed bed tubular reactor under the conditions of nitrogen atmosphere, by varying temperature and different particle sizes. The effect of final pyrolysis temperature from 400 to 500°C and the nitrogen flow rate from 50 to 200 cc min⁻¹ on the pyrolysis product yields from sugarcane bagasse have been investigated. The Maximum bio-oil yield obtained is 24.12 wt% at the final pyrolysis temperature of 450°C, N₂ flow rate of 50 cc min⁻¹ and particle size of mesh number −8 + 12. The yield of bio-oil decreases with increase in temperature from 450 to 550°C and N₂ flow rate from 50 to 200 cc min⁻¹. The various characteristics of pyrolysis oil obtained under these conditions were identified on the basis of standard test methods. The empirical formula of pyrolysis oil with a heating value of 37.01 MJ Kg⁻¹ was established as CH_1.434 O_0.555 N_0.004. The results from the pyrolysis show the potential of sugarcane bagasse as an important source of liquid hydrocarbon fuel.     

Simultaneous photocatalytic treatment of Cr(VI), Ni(II) and SDBS in aqueous solutions: Evaluation of removal efficiency and energy consumption

Simultaneous photocatalytic reduction of poisonous Cr(VI) and Ni(II) ions, coupled with photocatalytic oxidation of sodium dodecyl benzene sulfonate (SDBS) were studied with a trace amount of commercial titania nanoparticles and by means of a direct-photo-irradiation reactor. The co-presence of metal ions and SDBS causes metal ions reduction as well as SDBS oxidation to enhance and energy efficiency to improve. XRD, XPS and FTIR analysis were used to characterize TiO₂ particles before and after usage with the aim of evaluating the mechanism of reactions. The effect of major operating parameters, pH and temperature, was investigated. Under conditions of [Cr(VI)]₀ = [Ni(II)]₀ = 5 mg/L, [SDBS]₀ = 10 mg/L, [TiO₂] = 40 mg/L, pH 6 and T = 35 °C; the removal efficiencies of 55.4%, 71.2% and 57.2% were obtained, respectively, for Cr(VI) and Ni(II) reduction, as well as for SDBS oxidation, after 110 min operation. The relevant kinetic model jointed with the Arrhenius equation was introduced. Pseudo-first-order reactions are relevant. Energy consumption (electrical and thermal) evaluations revealed that operations at higher temperatures provide significant cost reduction. Meantime, a criterion was proposed for a consistent assessment of this kind of processes.     

Feasibility of honeycomb monolith supported sugar catalyst to produce biodiesel from palm fatty acid distillate (PFAD)

Carbon coated monolith was prepared by sucrose solution 65 wt.% via dip-coating method. Sulfonation of incomplete carbonized carbon coated monolith was carried out in order to synthesize solid acid catalyst. The textural structure characteristics of the solid acid catalyst demonstrated a low surface area and pore volume. Palm fatty acid distillate (PFAD), a by-product of palm oil refineries, was utilized as oil source in biodiesel production. The esterification reaction subjected to different reaction conditions was performed by using the sulfonated carbon coated monolith as heterogeneous catalyst. The sulfonation process had been performed by using vapour of concentrated H₂SO₄ that was much easier and efficient than liquid phase sulfonation. Total acidity value of carbon coated monolith was measured for unsulfonated sample (0.5 mmol/g) and sulfonated sample (4.2 mmol/g). The effect of methanol/oil ratio, catalyst amount and reaction time were examined. The maximum methyl ester content was 89% at the optimum condition, i.e. methanol/oil molar ratio (15:1), catalyst amount (2.5 wt.% with respect to PFAD), reaction time (240 min) and temperature 80 °C. The sugar catalyst supported on the honeycomb monolith showed comparable reactivity compared with the sugar catalyst powder. However, the catalyst reusability studies showed decrease in FFA% conversion from 95.3% to 68.8% after four cycles as well as the total acidity of catalyst dropped from the value 4.2 to 3.1 mmol/g during these cycles. This might be likely due to the leaching out of SO₃H group from the sulfonated carbon coated monolith surface. The leaching of active species reached a plateau state after fourth cycle.     

Decolorization of synthetic Methyl Orange wastewater by electrocoagulation with periodic reversal of electrodes and optimization by RSM

Treatment of Methyl Orange (MO), an azo dye, synthetic wastewater by electrocoagulation with periodic reversal of the electrodes (PREC) was examined. Response Surface Methodology (RSM) was used to optimize the influence of experimental conditions for color removal (CR), energy consumption (ENC), electrode consumption (ELC) and sludge production (SP) per kg MO removed (kg(MO_r)) with optimal conditions being found to be pH 7.4, solution conductivity (к) 9.4 mS cm⁻¹, cell voltage (U) 4.4 V, current density (j) 185 mA cm⁻², electrocoagulation time (T) 14 min, cycle of periodic reversal of electrodes (t) 15 s, inter-electrode distance (d) 3.5 cm and initial MO concentration of 125 mg L⁻¹. Under these conditions, 97 ± 2% color was removed and ENC, ELC and SP were 44 ± 3 kWh kg(MO_r)⁻¹, 4.1 ± 0.2 kg(Al) kg(MO_r)⁻¹ and 17.2 ± 0.9 kg(sludge) kg(MO_r)⁻¹, respectively. With the enhanced electrochemical efficiency resulting from the periodic electrode reversal, the coefficients of increased resistance and decreased current density between the two electrodes in the PREC setup were 2.48 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.29 mA cm⁻² min⁻¹, respectively, as compared to 7.72 × 10⁻⁴ Ω cm⁻² min⁻¹ and 0.79 mA cm⁻² min⁻¹ as measured for the traditional electrocoagulation process. The rate constant of decolorization was also enhanced by 20.4% from 0.152 min⁻¹ in the traditional electrocoagulation process to 0.183 min⁻¹ in the PREC process. These performance characteristics indicate that the PREC approach may be more promising in terms of practical application, as a cost-effective treatment, than conventional electrocoagulation for textile dye removals.     

Removal of H2S by co-immobilized bacteria and fungi biocatalysts in a bio-trickling filter

Biological control of odor gases has gained more attention in recent years. In this study, removal performance of a vertical bio-trickling filter inoculated with bacteria and fungi was studied. Bacteria and fungi were isolated from activated sludge in a sewage treatment plant. By adopting “three step immobilization method”, the bio-trickling filter could degrade pollutant immediately once hydrogen sulfide (H₂S) passed. The optimal empty bed resident time was 20 s. The optimal elimination capacity was about 60 g H₂S m^?3 h^?1 with removal efficiency of 95%. And the maximum elimination capacity was 170 g H₂S m^?3 h^?1. Pressure drop was ranged between 5 and 15 mm H₂O per bed over the whole operation. Removal efficiency was not affected obviously after terminating nutrient supply. The bio-trickling filter could recover back after shut down H₂S gaseous and liquid supplies simultaneously. Microbial community structure in the bio-trickling filter was not changed significantly.Combining bacteria and fungi would be a better choice for inoculation into a bio-trickling filter because of the quickly degradation of H₂S and rapid recovery under shut-down experiment. This is the first study attempting to combine bacteria and fungi for removal of H₂S in a bio-trickling filter.     

Partial nitritation of landfill leachate with varying influent composition under intermittent aeration conditions

The start-up and operation of a partial nitritation sequencing batch reactor for the treatment of landfill leachate were carried out on intermittent aeration mode. Partial nitrite accumulation was established in 15 days after the mode was changed from continuous aeration to intermittent aeration. Despite the varying influent composition, partial nitritation could be maintained by adjusting the hydraulic retention time (HRT) and the air flow rate. An increase in the air flow rate together with a decrease in air off duration can improve the partial nitritation capacity and eventually result in the development of granular sludge with fine diameters. A nitrogen loading rate of 0.71 ± 0.14 kg/m³/d and a COD removal rate of 2.21 ± 0.13 kg/m³/d were achieved under the conditions of an air flow rate of 19.36 ± 1.71 m³ air/m³/h and an air on/off duration of 1.5 min/0.7 min. When the ratio of total air flux (TAF) to the influent loading rate (ILR) was controlled at the range of 163–256 m³ air/kg COD, a stable effluent NO₃^?–N/NO_x^?–N (NO₂^?–N plus NO₃^?–N) ratio below 13% was achieved. Interestingly, the effluent pH was found to be a good indicator of the effluent NO₂^?–N/NH₄⁺–N ratio, which is an essential parameter for a subsequent anaerobic ammonium oxidation (Anammox) reactor.     

Use of advance oxidation process to improve the biodegradability of olive oil mill effluents

In this study, recalcitrant total phenol (TPh) and organic matter removal were investigated at olive mill wastewater (OMW) in sequential Coagulation and Fenton system. This study focused on different operational parameters such as pH, H₂O₂, and Fe²⁺ dosages, and [Fe²⁺]/[H₂O₂] ratios. The optimum conditions were determined as; pH = 3; [Fe²⁺] = 2.5 g/L; [Fe²⁺]/[H₂O₂] = 2.5. A higher treatment efficiency was achieved at sequential Coagulation and Fenton system (COD, 65.5%) and TPh, 87.2%), compared to coagulation process (COD, 51.4%; total organic carbon (TOC), 38.6% and total nitrogen (TN) 52.1%). This study demonstrated that the Coagulation and Fenton process has a potential for efficient removal of phenolic pollutants from wastewater.     

Synthesis and adsorption studies of NiO nanoparticles in the presence of H2acacen ligand,for removing Rhodamine B in wastewater treatment

Cost efficient NiO nanoparticles were synthesized by hydrothermal production of nano-scale Ni(OH)₂, using Ni(NO₃)₂·6H₂O and NaOH as precursors, in the presence of H₂acacen ligand, followed by calcinations of the produced Ni(OH)₂. Prepared samples were then characterized using X-ray powder diffraction (XRD), field-emission scanning electron microscopy (FESEM), Fourier transform infrared (FT-IR) spectra, Brunauer–Emmet–Teller (BET) and transmission electron microscopy (TEM). BET analysis revealed high surface area for pure nano sized NiO, averaging 176.56 m²/g and confirming its application as an efficient adsorbent. Experimental studies for Rhodamine B (RB) removal from aqueous solutions in batch systems revealed that the adsorption equilibrium was best represented by Langmuir isotherm, with the maximum monolayer capacity of 111 mg/g for RB. The kinetic data was well described by a pseudo-second-order kinetic model, having intraparticle diffusion model as a rate limiting step.     

Preparation of Co–MgO mixed oxide nanocatalysts for low temperature CO oxidation: Optimization of preparation conditions

In this study, a series of Co–MgO mixed oxides (30 wt.% Co) were prepared by co-precipitation method and employed as catalyst in low temperature CO oxidation reaction. The preparation conditions were optimized by the Taguchi method of experimental design to synthesize a sample with high catalytic performance toward CO oxidation reaction. The effects of four variables, pH of solution, aging temperature, aging time and molarity of precursor solution at three levels were investigated. The optimized sample was characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), temperature programmed desorption of oxygen (O₂-TPD), N₂ adsorption/desorption, thermal gravimetric and differential thermal analysis (TGA/DTA), and transmission electron microscopy (TEM) techniques. The results revealed that the optimized sample showed a mesoporous structure with a narrow pore size distribution centered in the range of 7–17 nm and particle size about 5.5 nm. It was found that the molarity of solution and aging time had the most influence on the CO conversion, respectively. The catalytic results showed that the highest CO conversion obtained from samples synthesized by Taguchi orthogonal array was about 90% at 200 °C, while the CO conversion for optimized sample was 95%. In addition, the effect of operational conditions was studied over optimized sample.     

Calorimetric behaviors of N2H4 by DSC and superCRC

The objective of this study is to obtain information about the thermal decomposition behaviors of hydrazine (N₂H₄) caused by metals, using differential scanning calorimeter (DSC) and SuperCRC. The DSC measurements revealed that the exothermic reactions of N₂H₄ were caused by the reaction conditions such as the type of cells; the T_DSC with a gold pan is 485.2 K and that with a glass capillary is 620.5 K. Besides, the activation energy of the thermal decomposition of N₂H₄, calculated from the Kissinger and Ozawa methods, were found to be about 38±2 kJ mol⁻¹ in the gold pan and 141±8 kJ mol⁻¹ in the glass capillary. Moreover, a heat flow profile was observed with SuperCRC during the mixing of N₂H₄ and the metal ion solution at 298 K. The maximum heat flow was related to the metal ion oxidative characters. The higher oxidative characters would provide a faster acceleration for the exothermic behavior than the lower oxidative ions. Based on this study, Mn(VII) and Cr(VI) were considered to exhibit strongly oxidative characteristics during mixing with N₂H₄.     

Pretreatment of municipal landfill leachate by a combined process

Biodegradability enhancement of landfill leachate using air stripping followed by coagulation/ultrafiltration (UF) processes was introduced. The air stripping process obtained a removal efficiency of 88.6% for ammonia nitrogen (NH₄–N) at air-to-liquid ratio of 3500 (pH 11) for stripping 18 h. The single coagulation process increased BOD/COD ratio by 0.089 with the FeCl₃ dosage of 570 mg l^?1 at pH 7.0, and the single UF process increased the BOD/COD ratio to 0.311 from 0.049. However, the combined process of coagulation/UF increased the BOD/COD ratio from 0.049 to 0.43, and the final biological oxygen demand (BOD), chemical oxygen demand (COD), NH₄–N and colour of leachate were 1223.6 mg l^?1, 2845.5 mg l^?1, 145.1 mg l^?1 and 2056.8, respectively, when 3 kDa molecular weight cut-off (MWCO) membrane was used at the operating pressure 0.7 MPa. In ultrafiltration process, the average solution flux (J_V), concentration multiple (M_C) and retention rate (R) for COD was 107.3 l m^?2 h^?1, 6.3% and 84.2%, respectively.     

Detoxification of hexavalent chromium in wastewater containing organic substances using simonkolleite-TiO2 photocatalyst

Innovative simple method for the preparation of simonkolleite-TiO₂ photocatalyst with different Zn contents was achieved. The prepared photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), FT-IR, Raman and diffuse reflectance spectroscopy techniques. The photocatalytic activities of the materials were evaluated for the simultaneous detoxification of hexavalent chromium (Cr(VI)) and oxidation of organic compounds commonly present in wastewater under simulated solar light. The best photoreduction efficiency of Cr(VI) has been achieved at 1000 ppm simonkolleite-TiO₂ photocatalyst of 5% Zn/TiO₂ weight ratio, and pH value of 2.5 to enhance the adsorption onto catalyst surface. Photoreduction was significantly improved by using formic acid as holes scavenger owing to its chemical adsorption on the catalyst surface. Finally, 100% photoreduction of Cr(VI) could be achieved using formic/simonkolleite-TiO₂ systems under sunlight.     

Effect of ultrasound irradiation and Ni-loading on properties and performance of CeO2-doped Ni/clinoptilolite nanocatalyst used in polluted air treatment

In this research nanocatalysts containing 5, 10 and 15 wt.% of Ni, dispersed by sonication over CeO₂–clinoptilolite composite support were compared toward total oxidation of toluene. Their catalytic performance at different temperatures between 150 and 350 °C was studied based on the oxidative destruction of toluene. The results indicated that the activity of Ni/CeO₂–clinoptilolite nanocatalyst for toluene oxidation increased from 33 to 44% at 250 °C by employing sonochemical method in synthesis of catalyst. Meanwhile, the catalytic activity was also improved when Ni content was increased from 5 to 10 and 15 wt.%. With the aid of several characterization techniques like XRD, FESEM, PSD, EDX, BET and FTIR, the correlation between nanocatalyst structure and its activity was addressed. It is indicated that sonochemical method can lift the catalytic activity due to the better dispersion of catalyst active components and also higher surface area. Among sonicated samples, 15 wt.% Ni nanocatalyst showed the highest toluene oxidation due to the better dispersion of catalyst active components and hence to more effective catalytic sites.     

On–off control of aeration time in the simultaneous removal of ammonia and manganese using a biological aerated filter system

The biological aerated filter (BAF) system, a new alternative in drinking water treatment, was designed to remove NH₄⁺–N and Mn²⁺ simultaneously. This study aimed to control the aeration time in the BAF system for simultaneous NH₄⁺–N and Mn²⁺ removal to achieve the Malaysian effluent quality regulation for drinking water. The experiment was conducted under four strategies of S1, S2, S3 and S4. The results demonstrated that acceptable levels of NH₄⁺–N and Mn²⁺ were achieved over a 6 h aeration period (S1), producing effluent concentrations of 0.7 mg/L (93.2% removal) and 0.08 mg/L (79.6% removal), respectively. At the initial treatment of S1 and S2, the dissolved oxygen (DO) level rapidly increased until it reached a saturated concentration (6.8 mg/L DO) after 2 h period. Automatic on–off aeration time to maintain 3 mg/L DO set point (S4) resulted with a good effluent quality of NH₄⁺–N and Mn²⁺ compared with the 2 mg/L DO set point (S3) which did not meet the regulated standard limits. Through the automatic on–off aeration time, the saturated and excessive DO levels in the BAF system can be avoided consequently reduce the wastage of energy and electrical consumption for simultaneous NH₄⁺–N and Mn²⁺ removal from drinking water treatment.