电催化氧化中的三种催化材料处理酸性红B染料的比较研究

本文采用三种不同催化机理的材料－－半导体材料TiO2、软锰 矿石和混合稀土进行了电催化氧化（ECO）染料酸性红B的研究,结果表明,稀土材料在ECO体系中呈负催化效应;软锰矿石的色度去除催化效果;TiO2的催化效果最显著,其色度和COD去除效果可比无催化剂时效果分别提高60％和75％,可以作为电催化氧化 的氧化剂。并进一步研究了TiO2用量对电催化氧化（ECO）的影响。     

高浓度难降解有机废水的催化氧化技术及其进展

根据催化剂的激活因子不同 ,本文将催化氧化法分为湿式催化氧化法 (WCO)、光催化氧化法 (PCO)和电催化氧化法 (ECO)三种 ,并阐述了各自的反应机理及应用研究状况 ,提出了今后需要加强的研究方向     

高浓度难降解有机废水的催化氧化技术及其进展

根据催化剂的激活因子不同，本文将催化氧化法分为湿式催化氧化法（WCO）、光催化氧化法（PCO）和电催化氧化法（ECO）三种，并阐述了各自的反应机理及应用研究状况，提出了今后需要加强的研究方向。     

光催化氧化法处理垃圾填埋场渗滤液的研究

研究了紫外光催化氧化法对垃圾填埋场滤渗液的降解机理,根据废水质的不同,考察了TiO2催化剂用量,pH值,通气量,反应时间,光照强度等因素对放心水中有机污染物和色度去除的最佳条件,用现场采集的渗滤液原水和氧化沟出水试验,CODcr去除率分别达到80．6％,77．3％,色度去除率分别为87．9％,83．3％。     

Mn-Fe-Ce/γ-Al2O3催化剂的制备及其在奶牛养殖废水处理中的臭氧催化氧化性能

不同地区的奶牛养殖废水水质具有地域性。在南方地区,常规处理工艺出水COD和色度普遍偏高,臭氧催化氧化是一种非常有潜力的技术。采用优化的浸渍焙烧的制备方法,以γ-Al_2O_3为载体,制备了Mn-FeCe/γ-Al_2O_3催化剂,并对其性状进行了表征。将该催化剂用于实际奶牛养殖废水一级好氧池出水的臭氧氧化中,结果表明:经含锰、铁和铈化合物的前驱体浸渍液浸渍并进行焙烧方法得到的Mn-Fe-Ce/γ-Al_2O_3催化剂对奶牛养殖废水有较好的催化性能;在臭氧投加量为12.5 mg·(L·min)~(-1),催化剂投加量为60 g,反应20 min的条件下,COD去除率由使用γ-Al_2O_3时的20.4%提高到48.9%,单独使用臭氧时仅为13.8%;色度去除率可达95%;BOD_5/COD达到0.54。臭氧催化氧化不仅可以去除COD和色度,而且有效改善了可生化性,为氧化出水继续使用生化法创造了条件。添加TBA作为HO·的淬灭剂实验结果表明,HO·在体系中起主要作用。研究结果可为奶牛养殖废水处理提供新的技术方法。     

软锰矿催化氧化脱除烟气中的SO2

对软锰矿催化氧化法去除烟气中SO2的方法进行了探索，研究了各工艺参数对烟气中SO2去除率的影响。结果表明：MnO2与Mn^2 的催化效果较好，传质过程对脱硫过程的影响较大，软锰矿浆在合适条件下能有效吸收低浓度的SO2。     

臭氧催化氧化去除水中聚乙烯醇

以Fe~(~(2+))、Mn~(~(2+))和Cu~(~(2+))为催化剂,运用臭氧催化氧化技术对水中聚乙烯醇进行去除实验。结果表明:与单独臭氧氧化比较,臭氧催化氧化对聚乙烯醇的去除效果明显提高,且与催化剂浓度相关,去除效果随Fe~(~(2+))浓度的增大而提高,在35 mg/L左右达最大值,去除率为85%;随Mn~(~(2+))浓度的增大而降低,最佳含量约为5 mg/L,去除率为54%;加入Cu~(~(2+))催化剂,在35 mg/L时去除率为5%,其他剂量时去除效果不明显。3种催化剂投加量同为35 mg/L,反应时间3 h条件下,去除效果对比为:Fe~(~(2+))Cu~(~(2+))Mn~(~(2+))。     

催化湿式氧化农药废水及催化剂的研究

通过浸渍法制备了4种氧化物为主活性组分的负载固定型催化剂,用于过氧化氢催化湿式氧化(CWHPO)处理有机农药废水。用实验确定了催化湿式氧化的条件,不同催化剂处理效果的比较表明,四元组合MnO2CuOCeO2CoO催化剂性能较好,当反应在常温常压下,维持pH=7～9,反应时间为40min时,COD的去除率大于80%,色度去除率大于90%。     

铁及铁铜氧化物对臭氧氧化酸性红B的催化效能

采用自蔓延溶胶凝胶法分别制备了铁氧化物和铁铜复合氧化物催化剂,以酸性红B为降解对象,对比了单独臭氧氧化、铁氧化物和铁铜复合氧化物催化臭氧氧化对酸性红B的降解效果,考察了磁力搅拌速度(500～1 640 r/min)、溶液pH(3～11)、臭氧投加速率(3.55～28.4 mg/min)对铁铜复合氧化物催化性能的影响。结果表明,与单独臭氧氧化比较,铁氧化物和铁铜复合氧化物均能加速酸性红B的降解,促进色度和COD的去除,结合催化剂的表征结果,推断催化剂表面羟基促进臭氧分解产生.OH是其氧化性能较好的主要原因,另外,催化剂的吸附能力对催化性能也有一定影响。随着磁力搅拌速度、溶液pH、臭氧投加速率的增大,铁铜复合氧化物催化臭氧氧化酸性红B的效果越好。     

催化氧化法处理印染废水试验

以镍氧化物催化剂和次氯酸钠配合使用处理和印染废水的静态与动态试验表明，该催化氧化方法处理过程简单，去除ＣＯＤ，色度的效果好，是一项值得研究并加以推广的新技术。     

纳米RuO2－TiO2光电催化处理农药废水研究

采用自制的负载型纳米RuO₂－TiO₂光催化剂对农药厂生产废水进行光电催化降解试验。考察了煅烧时间、催化剂用量、光辐照强度、电流密度、废水初始pH值和反应时间对废水COD和色度去除率的影响。结果表明，自制光催化剂光电催化性能显著，最佳光电催化活性是同样降解条件下、同样含量的Degussa P－25 TiO₂的1.38倍，是Ru_0.3Ti_0.7O₂的1.81倍。其COD和色度去除率分别为64.3%和95.2%。     

超声波-TiO_2光催化联合处理垃圾渗滤液

采用超声波强化TiO2光催化技术处理垃圾渗滤液。研究了TiO2催化剂用量、光照作用、超声波作用、pH值、曝气作用等因素对垃圾渗滤液中COD和氨氮去除率的影响。结果表明,在TiO2粉末的投加量为2 g/L、pH值为11时,先采用功率为292.5 W的超声波辐射3 min,再以高压汞灯(250 W)照射3 min,垃圾渗滤液中的COD和NH3-N去除率分别达到50.1%和75%。若在同一条件下进行饱和曝气可以使NH3-N去除率进一步达到85.3%,但会降低COD的去除率。     

The effects of manganese precursors on Mn-based/TiO2 catalysts for catalytic reduction of NO with NH3

Manganese acetate (MnAc) and manganese nitrate (MnN) were employed as precursors for the preparation of MnAc)/TiO2, Mn (N)/TiO2, Mn(Ac)-Ce/TiO2, and Mn(N)-Ce/TiO2 by impregnation. These complexes were used as catalysts in the low-temperature selective catalytic reduction of NO with NH3. The influence of manganese precursors on catalyst characteristics, the reduction activity, and the stability of the catalysts to poisoning by H2O and SO2 were studied. Experiments showed that Mn(N) produced MnO2 with large grain sizes in Mn(N)/TiO2 catalyst. On the contrary, Mn(Ac) led to highly dispersed and amorphous Mn2O3 in Mn (Ac)/TiO2 catalyst, which had better catalytic activity and stability to SO2 at low temperatures. The doping of cerium reduced the differences in catalytic performance between the catalysts derived from different Mn precursors.     

Sequential treatment via Trametes versicolor and UV/TiO2/Ru(x)Se(y) to reduce contaminants in waste water resulting from the bleaching process during paper production

An efficient sequential, biological and photocatalytic treatment to reduce the pollutant levels in wastewater due to the bleaching process during paper production is reported. For a biological pre-treatment, 800 ml of non-sterilized effluent was inoculated with Trametes versicolor immobilized in polyurethane foam, with 25 g l(-1) glucose, 6.75 mM CuSO(4), and 0.22 mM MnSO(4) added, and cultured at 25 degrees C with an air flow of 800 ml min(-1) for 8d. The fungus did not inhibit growth of the heterotropic populations of the effluent. After 4d of culture, the chemical oxygen demand (COD) reduction and colour removal (CR) were 82% and 80%, respectively, with laccase (LAC) and manganese peroxidase (MnP) activities of 345 U l(-1) and 78 U l(-1), respectively. The COD reduction and CR correlated positively (p<0.0001) with LAC and MnP activities. Chlorophenol removal was 99% of pentachlorophenol, 99% of 2,3,4,6-tetrachlorophenol (2,3,4,6-TCP), 98% of 3,4-dichlorophenol (3,4-DCP) and 77% of 4-chlorophenol (4-CP), while 2,4,5-trichlorophenol (2,4,5-TCP) increased to 0.2 mg l(-1). The pre-treated effluent was then exposed to a photocatalytic treatment. The treatment with photolysis resulted in 9% CR and 46% COD reduction, 42% CR and 60% COD reduction by photocatalysis, and 62% CR and 85% COD reduction by heterogeneous photocatalysis with the system TiO(2)/Ru(x)Se(y) (Fig. 4). With this treatment the bacterial and fungal populations also decreased by 5 logarithmic units with respect to the biological treatment alone (Fig. 5). The total sequential treatment resulted in a 92% CR (from 5800 UC), 97% COD reduction (from 59 g l(-1)) and 99% chlorophenol removal at 96 h and 20 min.     

添加壳聚糖溶胶-凝胶法制备的TiO2光催化剂及其光催化性能研究

采用添加壳聚糖（CTS）的溶胶-凝胶法制备了具有较高光催化活性的TiO2光催化剂，并用XRD、TEM、BET和IR等手段对其进行表征。结果表明，CTS的添加使TiO2衍射强度增强、分散性提高、比表面积增大从而使光催化活性提高；用所制备的催化剂光催化降解甲基橙反应60min后，其去除率由不添加CTS所制备TiO2的32％提高到48％，TOC去除率由14％提高到23％。     

电絮凝-催化氧化法去除染料工业废水COD的研究

我们对电絮凝 -催化氧化法处理染料工业废水COD进行了研究。实验结果表明 ,此方法对废水的COD具有良好的去除效果 ,并确定了相应的处理条件 :电解电压 4V ,电解时间 1.5h ,H2 O2 为 0 .6 % ,MO(含 75 %以上的TiO2 )为 2 .5g/L。平均COD去除率达到 77.5 %。电絮凝 -催化氧化法具有能耗低、操作简便等特点 ,为进一步深化处理奠定了基础     

负载型Mn-Ce／TiO2催化剂的制备及其低温脱硝活性

以成型TiO2作为载体，通过浸渍法制备了Mn-Ce／TiO2低温SCR催化剂，并系统研究了制备方法、煅烧条件、活性组分担载量、Mn含量等参数对催化剂催化还原NO性能的影响。结果表明，煅烧温度的升高会促使活性组分结晶度的提高，从而引起催化活性的降低，在500℃和600℃下所得Mn-Ce／TiO2催化剂活性组分为无定型态，表现出较高的脱硝活性。活性组分担载量的增加有利于催化活性的提高。Mn含量对Mn-Ce／TiO2催化剂的活性有较大影响，当Mn／（Mn＋Ce）摩尔比为40％和85％时，催化剂活性最高。     

微波诱导AC/Cu、AC/Fe催化非均相Fenton 反应催化降解垃圾渗滤液

采用活性炭载体负载Cu、Fe为催化剂,在微波诱导作用下,对垃圾渗滤液污染物进行降解。实验结果表明,活性炭负载金属前经适当浓度硝酸浸泡处理后,催化剂对COD去除率提高可超过15%,过高硝酸盐浓度对COD去除有不利影响;催化剂对COD去除率随Cu、Fe金属负载量增加呈先增加后降低的趋势,催化剂对Cu、Fe的最佳负载量分别为质量百分比2.11%和1.12%。对于AC-Cu体系,在初始pH=3,H2O2投加量为4.98×103mg/L,催化剂用量为5.0×103mg/L,420 W功率下微波辐射10 min时,垃圾渗滤液COD去除率可达到84.13%;对于AC-Fe体系,当H2O2投加量为0.33×103mg/L,催化剂AC-Fe用量为2.0×104mg/L,420 W功率下微波作用10 min时,垃圾渗滤液COD去除率为60.16%。分析2种催化剂对COD去除差异的原因,可能是催化剂AC-Cu表面单分子分布的阈值比AC-Fe高。降解液的pH值对AC-Cu体系、AC-Fe体系COD去除影响存在拐点,最高COD去除率点对应的降解液pH值为3。微波辐射功率较低时,体系COD去除率随辐射功率增加而增加;辐射功率较高时,高温下垃圾渗滤液中有机硫化物分解成小分子硫化物,对催化剂活性存在一定抑制作用。     

Wet air oxidation of a reactive dye solution using CoAlPO(4)-5 and CeO(2) catalysts

Wet air oxidation of a prepared reactive dye solution was performed to assess the efficacy of CoAlPO(4)-5 and CeO(2) as catalysts in the reaction. Via adsorption and oxidation of dye, CoAlPO(4)-5 effectively decreased American Dye Manufacturers Institute and chemical oxygen demand (COD) values in the dye solution. At a reaction temperature of 135 degrees C and an applied pressure of 1.0 MPa, color and COD removal were as high as 95% and 90%, respectively, after 2 h. Active sites on the outer surface of CoAlPO(4)-5 are responsible for adsorption and decomposition of dye while active sites in the pores dominate further destruction and oxidation of intermediate products. Since the outer surface only represents a minor part of the total surface, the color removal does not increase appreciably with loading of CoAlPO(4)-5. The CeO(2) catalyst, calcined from cerium chloride under high thermal impact (type A CeO(2)) was very effective in removing color and COD from the solution. This catalyst demonstrated near 100% color removal at temperatures above 135 degrees C and the COD removal could be above 95% at 165 degrees C. With both CoAlPO(4)-5 and CeO(2) catalysts, COD rose and then fell back during the reaction, a feature typical of a consecutive reaction. In contrast to prepared CeO(2), a commercial CeO(2) did not exhibit any catalytic ability for the removal of color and COD. The durability of both CoAlPO(4)-5 and prepared CeO(2) is considered to be fair.     

光催化氧化深度处理电镀有机废水的工程化实验

采用光催化氧化联用技术对电镀有机废水进行深度处理工程化实验。探讨了uV、uV＋H2O3、uV＋H2O2＋TiO2、uV＋H2O2＋FeSO4、uV＋H2O2＋FeSO4＋TiO2、uV＋O3＋TiO2和uV＋03＋TiO2＋H2O2等体系对废水有机污染物去除率的影响。结果表明，相较于其他反应体系，uV＋O3＋TiO2＋H2O2体系具有更好的氧化效果，经碳滤处理后去除率达到90％以上，最终出水水质满足GB18918-20O2-级标准（A标准）的要求。实际运行项目偿还期5．33年，NPV〉0，内部收益率大于基准值10％。研究表明，uV＋O3＋TiO2＋H2O，体系能降低加药量，工作量及运行成本。可为电镀企业实际废水处理提供现实依据，为优化电镀废水的处理工艺提供参考。