Degradation of azo dye Procion Red MX-5B by photocatalytic oxidation

The photocatalytic oxidation (PCO) of a monoazo dye Procion Red MX-5B under various physico-chemical conditions was investigated. Degradation of the dye by PCO was enhanced by augmentation in UV intensity, titanium dioxide and hydrogen peroxide concentrations but was inhibited by increase in initial dye concentration. The PCO process was affected by pH in a peculiar way. In the presence of 100 mg/l of TiO2 and the absence of H2O2, the highest reaction rate was observed when the initial pH was 10. With 500 mg/l of TiO2 and 10 mM of H2O2, the reaction was the fastest at initial pH of 3-5. The optimal conditions for the degradation of the dye, at an UV intensity of 17 mW/cm2, were determined to be: TiO2 concentration, 500 mg/l; initial H2O2 concentration, 10 mM; initial pH, 5.0. Monitoring of TOC loss showed that the dye was mineralized by 90% within 80 min under these conditions. Nevertheless, the persistence of a low level of TOC indicated that mineralization was not complete and dead-end product(s) which was (were) resistant to PCO might have accumulated.     

Photocatalytic degradation of azo dyes by nitrogen-doped TiO2 nanocatalysts

This study examined the photocatalytic degradation of three azo dyes, acid orange 7 (AO7), procion red MX-5B (MX-5B) and reactive black 5 (RB5) using a new type of nitrogen-doped TiO2 nanocrystals. These newly developed doped titania nanocatalysts demonstrated high reactivity under visible light (lambda>390 nm), allowing more efficient usage of solar light. The doped titania were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Experiments were conducted to compare the photocatalytic activities of nitrogen-doped TiO2 nanocatalysts and commercially available Degussa P25 powder using both UV illumination and solar light. It is shown that nitrogen-doped TiO2 after calcination had the highest photocatalytic activity among all three catalysts tested, with 95% of AO7 decolorized in 1 h under UV illumination. The doped TiO2 also exhibited substantial photocatalytic activity under direct sunlight irradiation, with 70% of the dye color removed in 1h and complete decolorization within 3 h. Degussa P25 did not cause detectable dye decolorization under identical experimental conditions using solar light. The decrease of total organic carbon (TOC) and evolution of inorganic sulfate (SO4(2-)) ions in dye solutions were measured to monitor the dye mineralization process.     

TiO2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有:X射线衍射光谱(XRD)、激光散射粒径分布、傅立叶变换红外光谱(FT-IR)、X射线光电子谱(XPS)和透射电子显微镜(TEM)。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂(H2O2)用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明:制备的TiO2胶体粒子平均粒径为13.8 nm(激光散法测定),光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/(L.min),平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2(含量30%)用量为0.2%(V/V),光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Composite tin and zinc oxide nanocrystalline particles for enhanced charge separation in sensitized degradation of dyes

Composite ZnO/SnO2 catalyst has been studied for the sensitized degradation of dyes e.g. Eosin Y (2', 4', 5', 7'-tetrabromofluorescein disodium salt) in relation to efficient charge separation properties of the catalyst. Improved photocatalytic activity was observed in the case of ZnO/SnO2 composite catalyst compared to the catalytic activity of ZnO, SnO2 or TiO2 powder. The suppression of charge recombination in the composite ZnO/SnO2 catalyst led to higher catalytic activity for the degradation of Eosin Y. Degradation of Eosin follows concomitant formation of CO2 and formation of CO2 followed a pseudo-first-order rate. Photoelectrochemical cells constructed using SnO2, ZnO, ZnO/SnO2 sensitized with Eosin Y showed V(oc) of 175, 306, 512 mV/cm2 and I(sc) of 50, 70, 200 microA/cm2 respectively. A higher irreversible degradation of Eosin Y and higher V(oc) observed on composite ZnO/SnO2 than ZnO and SnO2 separately can be considered as a proof of enhanced charge separation of ZnO/SnO2 catalyst. Eosin Y showed a higher emission decreases on ZnO/SnO2 composite than on individual ZnO, SnO2 or TiO2 indicating dominance of the charge injection process. Photoinjected electrons are tunneled from ZnO to SnO2 particles accumulating injected electrons in the conduction bands allowing wider separation of excited carriers.     

Photocatalytic degradation of dyes on a magnetically separated photocatalyst under visible and UV irradiation

A novel kind of magnetically separable photocatalyst of TiO2/SiO2/gamma-Fe2O3 (TSF) is prepared. Scanning tunnel microscope (STM) and X-ray diffractometer (XRD) were used to characterize the structure of the photocatalyst. In the TSF photocatalyst, a TiO2 shell is for photocatalysis, a gamma-Fe2O3 core as a carrier is for separation by the magnetic field and a SiO2 membrane between the TiO2 shell and the gamma-Fe2O3 core is used to weaken the adverse influence of gamma-Fe2O3 on the photocatalysis of TiO2. Three kinds of dyes, Fluoresein, Orange II and Red acid G, were used to examine the photocatalytic activity of TSF. Due to strong UV adsorption of the gamma-Fe2O3, the photocatalytic activity of TSF was lower than that of the pure TiO2. Deducting the light absorption of the gamma-Fe2O3 particles, the photocatalytic activity of TSF was found to be higher than that of the P25 under UV irradiation. On the other hand, the photocatalytic activity of TSF under visible irradiation was much lower than that of the P25 TiO2 even deducting the visible light absorption of the gamma-Fe2O3 particles. Differences in the photocatalytic mechanisms under UV and visible irradiation lead to the differences in the photodegradation characteristics of dyes on TSF. The recycled TSF exhibited a good repeatability of photocatalytic activity.     

The direct photolysis and photocatalytic degradation of alachlor at different TiO2 and UV sources

Direct photolysis and photocatalytic degradations of alachlor, a widely used herbicide, were studied using three different monochromatic UV lamps (254, 300 and 350 nm) and two TiO(2) sources. Both the direct photolysis and photocatalytic degradations of alachlor follow pseudo-first-order decay kinetics. TiO(2)-P25 was found to be an effective photocatalyst compared to TiO(2)-BDH. The direct photolysis of alachlor was dominant at 254 nm even if TiO(2) was present in the solution. Among the three UV wavelengths used, the highest photocatalysis quantum yield was obtained at 300 nm. The photocatalytic degradation rate of alachlor increased with the dosages of TiO(2), but an overdose of TiO(2) would retard the reaction due to light attenuation. Photocatalytic reactions were slightly enhanced in an alkaline medium, and the different proton sources causing various degrees of rate retardation were due to the presence of the corresponding counter anions. This effect was diminished at a later stage after the reaction intermediates were formed.     

Simultaneous decontamination of hexavalent chromium and methyl tert-butyl ether by UV/TiO2 process

Hexavalent chromium and methyl tert-butyl ether (MTBE) are two important environmental pollutants. Simultaneous decontamination of Cr(VI) and MTBE was studied by UV/TiO2 process. The influences of pH and the concentrations of pollutants on the kinetics of the photocatalytic reactions were evaluated. Dark adsorption tests showed that the acidic pH favored the adsorption of Cr(VI) while neutral pH favored the adsorption of MTBE. Under UV irradiation, Cr(VI) reduction was observed in Cr(VI)/TiO2 system, and MTBE oxidation was observed in MTBE/TiO2 system. The system containing Cr(VI) and MTBE by UV/TiO2 process demonstrated the synergistic effect between oxidation of MTBE and reduction of Cr(VI). The results demonstrated that two pollutants Cr(VI) and MTBE could be eliminated simultaneously by UV/TiO2 process. tert-Butyl formate, tert-butyl alcohol and acetone were identified as primary degradation products of MTBE by gas chromatography-mass spectrometry in the degradation of MTBE by UV/TiO2 process.     

TiO2光催化降解水中土霉素的动力学研究

环境中抗生素的出现及其引起的危害正受到越来越多的关注。以高压汞灯为光源，选用较为广泛的抗生素土霉素（OTC）为处理对象。考察了初始质量浓度、反应过程中光照、催化剂投加量、溶液起始pH、溶液中DOM和NO^-₃对光催化降解的影响，研究了其光降解动力学。结果表明，TiO₂光催化氧化法能够有效去除水中半微量的OTC，OTC的光降解过程符合一级反应动力学模型；UV/TiO₂联用工艺对TOC也有很好的去除效果，反应90 min，TOC去除率可达74%；OTC的初始浓度从30 mg/L增大到90 mg/L，反应速率从0.0619 min^-1降低到0.0130 min^-1；随着光催化剂投加量的增大，光降解速率常数先增大后减小；增加溶液的pH值，速率常数逐渐减小；溶液中的DOM和NO^-₃也可以影响光降解效率。     

TiO_2胶体光催化降解罗丹明B染料

TiO2胶体从钛氧有机物水解制备,表征的方法有：X射线衍射光谱（XRD）、激光散射粒径分布、傅立叶变换红外光谱（FT-IR）、X射线光电子谱（XPS）和透射电子显微镜（TEM）。利用罗丹明B染料分子作为探针分子研究TiO2胶体的光催化活性,分析了pH、催化剂用量、外加氧化剂（H2O2）用量及罗丹明B初始浓度对TiO2胶体光催化活性的影响。结果表明：制备的TiO2胶体粒子平均粒径为13.8 nm（激光散法测定）,光催化降解罗丹明B染料的反应属于一级动力学反应,可以用Langmuir-Hinshewood模型加以描述,反应速率常数k1为0.08413 mg/（L.min）,平衡吸附常数k2为1.5305 L/mg;在pH为6,TiO2胶体用量为0.04%,H2O2（含量30%）用量为0.2%（V/V）,光照度为69.6μW/cm2时,5 h后罗丹明B染料的降解率可达到99%以上;相似的条件,0.2%的P25 TiO2粉体光催化处理染料水时,罗丹明B的降解率为90%。纳米TiO2胶体不仅可以提高罗丹明B的光催化降解率,还具有用量少,可有效降低水处理成本的特点。     

Photocatalytic degradation of the herbicide erioglaucine in the presence of nanosized titanium dioxide: comparison and modeling of reaction kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO2 nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO2 system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir-Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm-1 and 0.984 ppm min-1, respectively. In this work, we also compared the reactivity between the commercial TiO2 Degussa P-25 and a rutile TiO2. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO2 for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO2 process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO2.     

Photocatalytic reactions of pyrene at TiO2/water interfaces

The photocatalytic oxidation of pyrene preadsorbed on TiO2 is examined in aqueous suspension under UV irradiation. Chemical oxygen demand measurements, UV-VIS spectrophotometer, infrared spectrometer and GC-MS analytical techniques were used to monitor the formed intermediates. During the oxidation processes, the ring-open reaction, hydroxylation and ketolysis occurred to produce some intermediate products (4-oxapyrene-5-one, 1,6- or 1,8-pyrenediones, 4,5-phenanthrenedialdehyde, cyclopenta[def]phenanthrene). Some factors affecting the photodegradation rate were also studied. The results were different from other studies: The pH of the dispersion, ratio of Py/TiO2:water had little effect on the photooxidation rate of pyrene catalyzed by TiO2, while the surface coverage, addition of Fe3+ affected it greatly.     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

光催化降解水体异味物质2-MIB的机理

以水体异味物质2-甲基异莰醇(2-methylisoborneol,2-MIB)为研究对象,在紫外光(λ<380 nm)照射下,探讨TiO2(P25)对2-MIB的光催化降解特性及光化学作用机理。结果表明,UV/TiO2光催化体系可以有效去除水体异味物质2-MIB,紫外光照射60 min,对2-MIB的降解率达95%。同时研究了光催化降解体系介质pH,共存腐殖酸(HA)和过硫酸钾(K2S2O8)对UV/TiO2光催化体系降解2-MIB的影响,发现低浓度HA([HA]≤0.5 mg/L)可以提高2-MIB降解速率,当HA浓度高于0.5 mg/L,2-MIB降解反应受到抑制;同时当加入电子受体K2S2O8后,降解体系中活性物种羟基自由基(.OH)明显增加,提高了TiO2对2-MIB的降解能力。利用苯甲酸荧光光度法和POD-DPD显色法跟踪测定降解过程中羟基自由基(·OH)和过氧化氢(H2O2)的变化,表明光催化反应涉及·OH机理。     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

3种染料化合物在UV-TiO2/H2O2和UV-TiO2体系中的光催化降解研究

采用自制的TiO2膜和平板式固定床型光催化氧化反应装置,对甲基橙、茜素红和罗丹明B 3种含有不同生色基团的染料化合物进行了TiO2光催化氧化降解研究,通过对照测定降解过程中吸光度、电导率、pH的变化,分析了在加入和不加入H2O22种情况下降解过程的异同,比较了3种染料化合物脱色的难易程度,揭示了降解产物中无机离子的变化规律及某些可能的产物类型.     

UV-TiO_2光催化氧化降解双酚A的动力学研究

采用自制光催化氧化反应器,研究了双酚A(BPA)在纳米TiO_2悬浆体系中的光催化氧化特性.结果表明:(1)UV-TiO_2对水中BPA有较强光催化氧化降解作用.在10 W低压汞灯照射下,当纳米TiO_2用量为1.0 g/L、pH为5.5、BPA初始质量浓度为10 mg/L、曝气量为4.0 mL/min、温度为室温、反应时间为120 min时,BPA去除率可达97.1%.当pH≥9.5时,120 min后BPA已经基本光催化氧化降解完全.(2)BPA的光催化氧化降解曲线均很好地符合一级反应动力学方程.其速率常数与纳米TiO_2用量、pH、BPA初始浓度、曝气量有关;促进·OH和电子-空穴对的生成是提高光催化氧化反应速率的重要途径.     

The pH and anion effects on the heterogeneous photocatalytic degradation of o-methylbenzoic acid in TiO2 aqueous suspension

This investigation used UV light of 365 nm and titanium dioxide in aqueous suspension to study the photocatalytic reaction of o-methylbenzoic acid under the influence of pH values, anion additives and the varieties of titanium dioxide. From experimental results, under the condition of 5 g/l TiO2, pH 3 and light intensity of 2.45 mW/cm2, 0.1 mM of o-methylbenzoic acid could be completely decomposed in 2 h. The reaction was faster with lowering pH, and was found to be apparent first-order following Langmuir-Hinshelwood model. In the presence of anion additives, the inhibitive effect of chloride ions was larger than that of sulfate ions under acidic condition for Degussa brand titanium dioxide, but without influence using Janssen brand. Both brands, however, promoted the mineralization of o-methylbenzoic acid (o-MBA).     

Decolorizing of lignin wastewater using the photochemical UV/TiO2 process

Studies on applying the photochemical UV/TiO2 oxidation process to treat the lignin-containing wastewater for dissolved organic carbon (DOC), color and reducing A254 (the absorption at the wavelength of 254 nm) have been carried out. The data obtained in this study demonstrate that the UV/TiO2 process is effective in oxidizing the lignin thus reducing the color and DOC of the wastewater treated. The combined UV/TiO2 treatment can achieve better removal of DOC and color than the UV treatment alone. Color removal, based on American Dye Manufacture Index (ADMI) measurement, is greater than 99% if the pH is maintained at 3.0 with the addition of 1 g l(-1) TiO2. When 10 g l(-1) TiO2 is applied, the oxidation reduction potential (ORP) value is reached to result in an 88% removal of both DOC and color. A model was developed based on the variation of ORP during the photochemical reaction to simulate the decoloring process. The proposed model can be used to predict the color removal efficiency of the UV/TiO2 process.