共查询到20条相似文献,搜索用时 109 毫秒
1.
2.
环境空气质量综合指数计算方法比选研究 总被引:1,自引:0,他引:1
环境空气质量综合指数是进行逐月城市环境空气质量比较和排序的重要方法,提出了4种涵盖SO2、NO2、PM10、PM2.5、CO、O3等6项污染物的综合指数计算方法,基于2013年74个城市逐月污染物浓度数据使用主成分分析方法进行了对比分析。结果表明,综合指数计算方法中污染物统计指标和标准化方法不同对于主要污染物的判定有重要影响,各种计算方法中PM2.5、PM10、O3是出现频率最多的主要污染物;除O3外其他5项污染物逐月统计指标间均有极显著的正相关性,冬季O3统计指标与SO2、NO2、PM10、PM2.5呈显著负相关,夏季则呈显著正相关;主成分分析结果表明,在去除冗余信息后,PM2.5、PM10的权重被相对削弱,SO2、NO2、CO的权重得到相对强化,O3的权重夏季得到强化、冬季被削弱;综合考虑不同方案下主要污染物频率分布情况和PM2.5、PM10、O3权重变化特征,建议计算逐月环境空气质量综合指数时,SO2、NO2、PM10、PM2.5宜以月均值除以年均值标准进行标准化,CO、O3宜以特定百分位数浓度除以日均值标准(或8 h均值标准)进行标准化;该方法可延伸到季、半年和年度的环境空气质量综合指数计算。 相似文献
3.
利用上海市虹口监测点2002年O3的连续自动监测数据,分析了该点代表的区域范围内O3的污染水平、变化情况,以及O3与NO、NOx和CO的关系。指出该点O3的污染水平是冬季最低,秋季最高,5月至10月的质量浓度明显高于11月至4月,低质量浓度时段在早晨,高质量浓度时段在中午至午后;O3质量浓度的变化范围和上升速率是5月至10月比11月至4月大;O3的产生主要取决于NOx中NO转换成NO2的程度,而CO也同NO一样,当O3质量浓度在中午至午后较高时,CO质量浓度也不高。 相似文献
4.
分别用在线和线外分析仪对不同类型公交车车厢的空气进行了监测,通过对CO、PM10、NO-NO2-NOx、SO2 和O3等污染因子的测定和分析,了解到影响车厢空气质量的污染因素与车龄工况、燃料,以及空调与排气系统有关,同时提出了控制污染的相关建议. 相似文献
5.
利用统计学和GIS方法对2016年武汉市各区不同污染物的时空分布特征及相关性进行分析。结果表明:武汉市大气污染季节性特征明显,春季和冬季颗粒物(PM2.5、PM10)及NO2污染突出,夏季O3污染严重。污染物空间差异显著,主城区和东西湖区颗粒物及NO2污染严重,郊区O3污染严重。平均气温、平均水汽压与SO2、NO2、CO、PM2.5和PM10均呈显著负相关,而与O3呈显著正相关;降水量与SO2、NO2和CO呈显著负相关。 相似文献
6.
为了研究北京地区PM2.5与空气污染物的质量浓度关系。从PM2.5监测网收集2013-04-01~2014-05-15期间PM2.5、PM10、SO2、NO2、CO、O3等主要空气污染物数据,用多元线性回归模型建立PM2.5与空气污染物的质量浓度关系。结果表明:北京地区PM2.5与空气污染物PM10、SO2、NO2、CO、O3的质量浓度相关系数分别为0.9172、0.6332、0.7683、0.8166和-0.1797,优化的拟合方程为:[PM2.5]=-22.5925+0.569109×[PM10]+23.94913×[CO]+0.113025×[BPM2.5],模型的估算值与观测值相关系数为0.9426,此方程能较好地模拟北京地区的PM2.5质量浓度。 相似文献
7.
沈阳市冬季环境空气质量统计预报模型建立及应用 总被引:5,自引:3,他引:2
利用沈阳市2013年1—2月大气自动监测数据和同期气象资料,选取19项预报因子,采用逐步回归方法建立了沈阳市冬季环境空气质量统计预报模型,预报项目包括细颗粒物(PM2.5)、可吸入颗粒物(PM10)、二氧化硫(SO2)、二氧化氮(NO2)、一氧化碳(CO)日均浓度及臭氧(O3)日最大8 h平均浓度。2013年11月至2014年1月,应用该模型并结合人为经验修订,开展了沈阳市环境空气质量预报工作,预报结果与实测结果的对比验证结果表明,环境空气预测结果级别准确率达到79.1%,首要污染物准确率为73.6%。 相似文献
8.
介绍了国内外二氧化碳( CO2)气体检测方法,选取红外传感器、非分散红外和气相色谱3种方法监测工业燃煤废气中的CO2。试验结果表明,3种方法的精密度和准确度均满足要求;单一燃煤废气中CO2的体积分数范围为6.70%~15.10%,同一排气筒中CO2体积分数5 min的波动范围为0~22.4%;同一排气筒(单一燃煤废气)中CO2和O2的体积分数有一定的关联性,二者之和基本稳定在19%~21%范围;非分散红外法和气相色谱法测定同一样品的相对偏差为0.9%~3.4%;红外传感器适用于有组织排放的现场监测,另2种方法适用于无组织废气和环境空气监测。 相似文献
9.
差分光谱法连续监测空气中SO2、NO2、苯、甲苯方法探讨 总被引:1,自引:0,他引:1
差分光谱法(简称DOAS)已广泛用于空气中SO2、NO2、苯、甲苯监测.通过对差分光谱法监测结果与其他传统仪器进行时比,发现用DOAS监测SO2、NO2与点式仪器有较好的一致性,但用DOAS系统监测苯、甲苯与气相色谱法有机物连续监测结果差异较大,相关性较差,运行有一定的局限性.另外,本文对DOAS的最佳运行条件进行了探讨,发现影响光强的氙灯老化和气候条件对DOAS系统运行有较大影响. 相似文献
10.
因子分析法在金泉工业园区地下水水质评价中的应用 总被引:1,自引:0,他引:1
根据金泉工业园水源地8个不同监测断面的地下水水质监测数据,采用R型因子分析法对园区水源地地下水水质进行综合评价,在研究地下水中13种化学成分间相关关系的基础上,提取4个主因子进行分析计算。结果表明,Cl-、SO24-、总硬度和可溶性固体对第一主因子贡献明显;第二主因子代表指标是Zn;第三主因子代表指标是As;NO3-、氨氮、NO2-对第四主因子贡献显著。对水质进行综合评价后发现,人民渠、海流图河和乌拉壕监测断面处水质类别为V类,其他断面均为IV类。因子分析法从整体上评价了园区水源地地下水的水质现状,分析结果清晰明确,为日后地下水资源的管理与保护提供科学依据。 相似文献
11.
Strobl RO Robillard PD Shannon RD Day RL McDonnell AJ 《Environmental monitoring and assessment》2006,112(1-3):137-158
The principal instrument to temporally and spatially manage water resources is a water quality monitoring network. However,
to date in most cases, there is a clear absence of a concise strategy or methodology for designing monitoring networks, especially
when deciding upon the placement of sampling stations. Since water quality monitoring networks can be quite costly, it is
very important to properly design the monitoring network so that maximum information extraction can be accomplished, which
in turn is vital when informing decision-makers. This paper presents the development of a methodology for identifying the
critical sampling locations within a watershed. Hence, it embodies the spatial component in the design of a water quality
monitoring network by designating the critical stream locations that should ideally be sampled. For illustration purposes,
the methodology focuses on a single contaminant, namely total phosphorus, and is applicable to small, upland, predominantly
agricultural-forested watersheds. It takes a number of hydrologic, topographic, soils, vegetative, and land use factors into
account. In addition, it includes an economic as well as logistical component in order to approximate the number of sampling
points required for a given budget and to only consider the logistically accessible stream reaches in the analysis, respectively.
The methodology utilizes a geographic information system (GIS), hydrologic simulation model, and fuzzy logic. 相似文献
12.
主要阐述了光散射法扬尘在线监测应用于建筑工地、干散货码头堆场、混凝土搅拌站的质量管理和质量评估。为了提高光散射法扬尘在线监测的数据质量,上海市采取扬尘在线监测设备现场质量抽测的模式,通过对在用仪器的监测点位、除湿方式、校准方式、质量浓度转换系数、与标准重量法监测结果的相对误差和相关系数、仪器运行维护水平等影响监测质量和数据有效性的关键指标的检查,开展扬尘监测在用仪器质量评估和仪器商合格评定,稳步提高在用仪器质量,为在线监测质量管理和质量评估提供可借鉴的技术方案和实践经验。 相似文献
13.
14.
15.
The possibility of acquiring real-time concentration data is leading many indoor air quality and health researchers to the use of particle measuring instruments instead of the classic filtration approach. This paper summarizes a checklist of characteristics that have to be considered on the selection of such instruments and checks the compliance of three air monitoring devices suitable for environmental exposure researches. An evaluation table with desirable instrument technical, economic, and logistics characteristics was summarized in a checklist, and spec sheets of three air monitoring devices suitable for environmental exposure researches were checked. Technical, economic, and logistics aspects have to be considered. Suitability, measurement range, accuracy, resolution, and robustness are indispensable metrological characteristics. Only one instrument was in comply with it. A popular air monitoring device among environmental exposure researchers was checked and it failed the accuracy check. When selecting a particle measuring instrument, technical, economic, and logistics aspects have to be considered. Suitability, measurement range, accuracy, resolution, and robustness are indispensable metrological characteristics. When selecting an instrument for a study, a lack of information on the quality of results is a strong indication that it should not be considered, as study's response may be compromised. 相似文献
16.
17.
18.
地表水高锰酸盐指数自动监测仪器在实际应用中存在质控样测试和实际水样比对测试合格率相对偏低的问题。通过对高锰酸盐指数氧化还原机理的分析,结合目前国控水站对质控样品的测试数据,探讨了如何使用高锰酸盐指数自动监测仪分析测试得到准确可靠的水质监测数据。认为应尽量保持自动分析仪器的反应条件、稀释条件与标准方法一致,即取样量与试剂用量比与标准方法一致,并根据样品浓度变化实现量程自动切换,分量程进行仪器校准和测量,才能够提高自动分析仪器测量的准确性。 相似文献
19.
Giovanna Moura Calazans Carolina Cristiane Pinto Elizângela Pinheiro da Costa Anna Flávia Perini Sílvia Corrêa Oliveira 《Environmental monitoring and assessment》2018,190(8):491
This study sought to evaluate and propose adjustments to the water quality monitoring network of surface freshwaters in the Paraopeba river basin (Minas Gerais, Brazil), using multivariate statistical methods. A total of 13,560 valid data were analyzed for 19 water quality parameters at 30 monitoring sites, over a period of 5 years (2008–2013). The cluster analysis grouped the monitoring sites in eight groups based on similarities of water quality characteristics. This analysis made it possible to detect the most relevant monitoring stations in the river basin. The principal components analysis associated with non-parametric tests and the analysis of violation of the standards prescribed by law, allowed for identifying the most relevant parameters which must be maintained in the network (thermotolerant coliforms, total manganese, and total phosphorus). The discharge of domestic sewage and industrial wastewater, that from mining activities and diffuse pollution from agriculture and pasture areas are the main sources of pollution responsible for the surface water quality deterioration in this basin. The BP073 monitoring site presents the most degraded water quality in the Paropeba river basin. The monitoring sites BP094 and BP092 are located geographically close and they measure similar water quality, so a possible assessment of the need to maintain only one of the two in the monitoring network is suggested. Therefore, multivariate analyses were efficient to assess the adequacy of the water quality monitoring network of the Paraopeba river basin, and it can be used in other watersheds. 相似文献
20.
通过仪器的不确定度试验,可以检验分析仪器引起的误差是否满足分析方法的要求,从而知道仪器对分析方法的适应性,同时可以知道作某一分析项目时,同类仪器中哪一台误差最小.监测分析仪器的不确定度试验是保证监测结果准确的手段之一. 相似文献