Polycyclic aromatic hydrocarbons in urban soils of Hangzhou: status,distribution, sources,and potential risk

Concentration, composition profile, spatial distribution, sources, and health risk of 16 polycyclic aromatic hydrocarbons (PAHs) were analyzed in 69 surface soil samples collected from Hangzhou urban districts. ∑PAHs ranged from 180.77 to 1,981.45 μg kg^?1 with a mean of 611.28 μg kg^?1. Among different functional areas, a higher level of PAHs was found in the roadsides, followed by commercial districts, residential areas, parks, and greenbelts. The composition of PAHs was characterized by high molecular weight PAHs (4?~?6 rings). Principal component analysis (PCA) and PAH isomeric ratios indicated that PAHs mainly originated from combustion, especially vehicle exhaust. The incremental lifetime cancer risks (ILCRs) associated with exposures to PAHs in soil were calculated separately for children and adults under normal and extreme conditions. The results showed that ILCRs for urban soil of Hangzhou were acceptable. However, attentions should be attracted on the sites of high PAH concentrations because the ILCRs were closed to 10^?4 under extreme conditions, especially for children.     

Identification of sources of elevated concentrations of polycyclic aromatic hydrocarbons in an industrial area in Tianjin, China

The concentrations of 16 polycyclic aromatic hydrocarbons (PAHs) were determined by gas chromatography equipped with a mass spectrometry detector in 105 topsoil samples from an industrial area around Bohai Bay, Tianjin in the North of China. Results demonstrated that concentrations of PAHs in 104 soil samples from this area ranged from 68.7 to 5,590 ng g^???1 dry weight with a mean of ∑16PAHs 814 ± 813 ng g^???1, which suggests that there exists mid to high levels of PAH contamination. The concentration of ∑16PAHs in one soil sample from Tianjin Port was exceptionally high (48,700 ng g^???1). Ninety-three of the 105 soil samples were considered to be contaminated with PAHs (>200 ng g^???1), and 25 were heavily polluted (>1,000 ng g^???1). The sites with high PAHs concentration are mainly distributed around chemical industry parks and near highways. Two low molecular weight PAHs, naphthalene and phenanthrene, were the dominant components in the soil samples, which accounted for 22.1% and 10.7% of the ∑16PAHs concentration, respectively. According to the observed molecular indices, house heating in winter, straw stalk combustion in open areas after harvest, and petroleum input were common sources of PAHs in this area, while factory discharge and vehicle exhaust were the major sources around chemical industrial parks and near highways. Biological processes were probably another main source of low molecular weight PAHs.     

Spatial distribution and temporal trends of polycyclic aromatic hydrocarbons in Mytilus galloprovincialis from the Iberian Mediterranean coast

Polycyclic aromatic hydrocarbons (PAHs) have been determined in blue mussels (Mytilus galloprovincialis) from several Iberian Mediterranean coastal areas through the implementation of a monitoring programme from Spain in the framework of the Mediterranean Pollution Programme (MED POL). The selected areas correspond to sites with differing degrees of exposure to the main pollution sources (hot spots, coastal and reference areas). The sampling campaigns were performed from 2004 to 2009, with samples being taken from May to June, the non-spawning period for mussels in this area. Thirteen PAHs were determined by high-performance liquid chromatography with specific fluorescence detection. In general, total PAHs concentration was lower than 50 μg kg^?1 d.w., except in areas close to the principal ports and cities (Barcelona, Tarragona, Valencia and Algeciras) where it varies from 75 to 390 μg kg^?1 d.w. Background concentrations have been proposed for PAHs in mussels (23.8 μg kg^?1 d.w.) from Western Mediterranean area. Temporal trends were not statistically significant for PAHs concentrations from 2004 to 2009. Longer monitoring periods would be required to detect a continuous tendency, especially for PAHs because although the efficiency of combustion engines has reduced PAHs emissions, their increasing use could alter this potential reduction. The predominant PAHs were three and four ring congeners in all cases, with the predominance of phenanthrene in mussels sited far from the main PAHs sources. The phenanthrene/anthracene (lower than 10) and fluoranthene/pyrene (higher than 1) ratios indicate that PAHs detected in Spanish Mediterranean coastal mussels are mainly of pyrolytic origin.     

Distribution and potential sources of polycyclic aromatic hydrocarbons in soils around coal-fired power plants in South Africa

The distribution and potential sources of 15 polycyclic aromatic hydrocarbons (PAHs) in soils in the vicinity of three South African coal-fired power plants were determined by gas chromatography–mass spectrometry. PAH compound ratios such as phenanthrene/phenanthrene + anthracene (Phen/Phen + Anth) were used to provide reliable estimation of emission sources. The total PAH concentration in the soils around three power plants ranged from 9.73 to 61.24 μg g^?1, a range above the Agency for Toxic Substances and Disease Registry levels of 1.0 μg g^?1 for significantly contaminated site. Calculated values of Phen/Phen + Anth ratio were 0.48?±?0.08, 0.44?±?0.05, and 0.38?+?0.04 for Matla, Lethabo, and Rooiwal, respectively. Flouranthene/fluoranthene + pyrene (Flan/Flan + Pyr) were found to be 0.49?±?0.03 for Matla, 0.44?±?0.05 for Lethabo, and 0.53?±?0.08 for Rooiwal. Such values indicate a pyrolytic source of PAHs. Higher molecular weight PAHs (five to six rings) were predominant, suggesting coal combustion sources. A good correlation existed between most of the PAHs implying that these compounds were emitted from similar sources. The carcinogenic potency B[a]P equivalent concentration (B[a] Peq) at the three power plants ranged from 3.61 to 25.25 indicating a high carcinogenic burden. The highest (B[a] Peq) was found in samples collected around Matla power station. It can therefore be concluded that the soils were contaminated with PAHs originating from coal-fired power stations.     

Mercury accumulation in fish species from the Persian Gulf and in human hair from fishermen

Total and methylmercury concentrations were assessed in muscle and liver of 141 fish samples from the northern part of the Persian Gulf. All fish samples belonged to five different species: grunt, flathead, greasy grouper, tiger-tooth croaker, and silver pomfret. In addition, Hg and methylmercury were analyzed in scalp hair of 19 fishermen living in the same coastal stations of the Persian Gulf and consuming several fish meals a week. Total mercury concentrations in fish muscle and liver ranged from 0.01 to 1.35 μg g^???1 w.w. and from 0.02 to 1.30 μg g^???1 w.w., respectively. In fish muscle, 3% of the Hg concentrations were higher than 0.5 μg g^???1 w.w., which corresponds to the maximum acceptable WHO level, while 9% were in the range of polluted fish (between 0.3 and 0.5 μg g^???1 w.w.). The highest mercury concentrations in fish muscle were observed in flathead fish at Abadan (average of 0.68 μ g g^???1 w.w.). Methylmercury fractions in fish muscle and liver amount to 34–99% (median 64%) and 24–70% (median 43%), respectively. The mean total Hg concentration in the fishermen’s scalp hair amounted to 2.9 ± 2.2 μ g g^???1, with 68% in the form of methylmercury. Ninety-five percent of the Hg levels in the fishermen’s hair were below 10 μ g g^???1, which is the WHO warning limit. In addition, relationships between the mercury levels in hair, on the one hand, and exposure-related factors such as Hg levels in specific fish species, regional differences, and number of fish meals, on the other hand, are discussed. It appears that a significant correlation for example exists between Hg levels human hair and fish muscle or human hair and age and that mean mercury levels in fish muscle and human hair decreased from western (Abadan) to eastern (Abbas port) coastal sites.     

The levels and composition of persistent organic pollutants in alluvial agriculture soils affected by flooding

The concentrations and composition of persistent organic pollutants (POPs) were determined in alluvial soils subjected to heavy flooding in a rural region of Poland. Soil samples (n?=?30) were collected from the upper soil layer from a 70-km² area. Chemical determinations included basic physicochemical properties and the contents of polychlorinated biphenyls (PCBs), hexachlorocyclohexanes (HCHs), dichlorodiphenyltrichloroethanes (DDTs) and polycyclic aromatic hydrocarbons (PAHs, 16 compounds). The median concentrations of Σ7PCB (PCB28?+?PCB52?+?PCB101?+?PCB118?+?PCB138?+?PCB153?+?PCB180), Σ3HCH (α-HCH?+?β-HCH?+?γ-HCH) and Σ3pp′(DDT?+?DDE?+?DDD) were 1.60?±?1.03, 0.22?±?0.13 and 25.18?±?82.70 μg kg^?1, respectively. The median concentrations of the most abundant PAHs, phenanthrene, fluoranthene, pyrene, benzo[b]fluoranthene and benzo[a]pyrene were 50?±?37, 38?±?27, 29?±?30, 45?±?36 and 24?±?22 μg kg^?1, respectively. Compared with elsewhere in the world, the overall level of contamination with POPs was low and similar to the levels in agricultural soils from neighbouring countries, except for benzo[a]pyrene and DDT. There was no evidence that flooding affected the levels of POPs in the studied soils. The patterns observed for PAHs and PCBs indicate that atmospheric deposition is the most important long-term source of these contaminants. DDTs were the dominant organochlorine pesticides (up to 99 %), and the contribution of the parent pp′ isomer was up to 50 % of the ΣDDT, which indicates the advantage of aged contamination. A high pp′DDE/pp′DDD ratio suggests the prevalence of aerobic transformations of parent DDT. Dominance of the γ isomer in the HCHs implies historical use of lindane in the area. The effect of soil properties on the POP concentrations was rather weak, although statistically significant links with the content of the <0.02-mm fraction, C_total or N_total were observed for some individual compounds in the PCB group.     

Presence, distribution, and origins of polycyclic aromatic hydrocarbons (PAHs) in sediments from Bahía Blanca estuary, Argentina

This paper is the first comprehensive survey of polycyclic aromatic hydrocarbons (PAHs) in coastal sediments in Bahia Blanca, Argentina, and provides useful information on their levels of concentration, composition, and sources of these pollutants. The total concentrations of PAHs ranged from 15 to 10,260 ng g^???1. The highest contents (mean 3,315 ng g^???1) of total PAHs in marine sediments were found in the inner channels of the estuary, while the lower ones (204 ng g^???1) belong to samples collected far away from contamination sources. The global average recorded in this study (1,500 ng g^???1) indicates that the studied area lies within the referenced category of industrialized coastal zones under chronic pollution. The diagenetic PAH contribution was found to be negligible at all sampled locations; however, the calculation of molecular ratios determined an overimposition of pyrolitic PAHs over the petrogenic input. Further, the use of principal components analysis (PCA) clearly separated ring group compounds and enabled the determination of pyrolitic/combustion PAHs dominancy.     

Spatial and temporal distribution of polycyclic aromatic hydrocarbons (PAHs) in sediments of the Nansi Lake, China

Polycyclic aromatic hydrocarbons (PAHs) were measured in surface sediments and dated core sediments from the Nansi Lake of China to investigate the spatial and temporal distribution characteristics. The concentrations of 16 kinds priority PAH compounds were determined by GC-MS method. And ²¹⁰Pb isotope dating method was used to determine the chronological age of the sediment as well as the deposition rate. The results indicated that the total PAHs concentration ranges in surface and core sediment samples were 160 ~32,600 and 137 ~ 693 ng/g (dry wt.), respectively. The sediment rate and the average mass sedimentation were calculated to be 0.330 cm·year^???1 and 0.237 g·cm^???2·yr^???1 and the sediment time of the collected core sample ranged from 1899 to 2000. The peak of PAH concentrations came at recent years. The source analysis showed PAHs mainly came from the contamination of low temperature pyrogenic processes, such as coal combustion. The PAHs concentrations were lower than ERL and LEL values for most collected samples. However, in several surface sediment samples especially in estuary sites, the PAHs concentrations were not only higher than ERL and LEL values, but also higher than ERM values.     

Persistence and bioaccumulation of oxyfluorfen residues in onion

A field study was conducted to determine persistence and bioaccumulation of oxyflorfen residues in onion crop at two growth stages. Oxyfluorfen (23.5% EC) was sprayed at 250 and 500 g ai/ha on the crop (variety, N53). Mature onion and soil samples were collected at harvest. Green onion were collected at 55 days from each treated and control plot and analyzed for oxyfluorfen residues by a validated high-performance liquid chromatography method with an accepted recovery of 78–92% at the minimum detectable concentration of 0.003 μg g^???1. Analysis showed 0.015 and 0.005 μg g^???1 residues of oxyfluorfen at 250 g a.i. ha^???1 rate in green and mature onion samples, respectively; however, at 500 g a.i.ha^???1 rates, 0.025 and 0.011 μg g^???1 of oxyfluorfen residues were detected in green and mature onion samples, respectively. Soil samples collected at harvest showed 0.003 and 0.003 μg g^???1 of oxyfluorfen residues at the doses 250 and 500 g a.i. ha^???1, respectively. From the study, a pre-harvest interval of 118 days for onion crop after the herbicide application is suggested.     

Polycyclic aromatic hydrocarbons in soils from Urumqi, China: distribution, source contributions, and potential health risks

Concentrations of 16 priority polycyclic aromatic hydrocarbons (PAHs) were measured in 28 surface soils samples collected from Urumqi, northwest China, for examination of distributions, source contributions, and potential health effects. The results indicated that the sum of 16 PAHs concentration ranged from 331 to 15,799 μg?kg^?1 (dw) in soils, with a mean of 5,018?±?4,896 μg?kg^?1 (n?=?28). The sum of seven carPAHs concentration ranged from 4 to 1,879 μg?kg^?1 (dw; n?=?28). The highest ∑PAHs concentrations were found at roadsides and industrial sites, followed by those at parks, rural areas, and business/residential areas. Coal combustion, emission of diesel and gasoline from vehicles, and petroleum source were four sources of PAHs as determined by PMF analysis, which contributed 51.19, 19.02, 18.35, and 11.42 % to the PAH sources, respectively. Excellent coefficients of correlation between the measured and predicted PAHs concentrations suggested that the PMF model was very effective to estimate sources of PAHs in soils. Incremental lifetime cancer risk values at the 95th percentile due to human exposure to surface soils PAHs in Urumqi were 2.02?×?10^?6 for children and 2.72?×?10^?5 for adults. The results suggested that the current PAHs levels in soils from Urumqi were pervasive and moderately carcinogenic to children and adults.     

Effect of combustion variables on PAHs emission from incineration of cellulose waste filters from acrylic industry

Incineration of cellulose waste filter from acrylic industry showed the presence of 13–16 polycyclic aromatic hydrocarbons (PAHs) from the list of 16 priority pollutants with an airflow rate of 1, 2, 3, and 4 L min^???1 in laboratory scale quartz tube vertical incinerator at 700–1,000°C at an interval of 100°C. The amount of total 16 PAHs increases with the increase in temperature with airflow rate of 1 L min^???1 and was found to be 9.4 times at 1,000°C than at 700°C. Studies at 800–1,000°C showed the decrease in total 16 PAHs with increase in airflow rate from 1 to 2 L min^???1. The amount of total 16 PAHs increases at 700, 800, and 1,000°C with increase in airflow rate from 2–4 L min^???1. At 900°C, amount of 16 PAHs decreases with increase in flow rate from 1 to 3 and increases at 4 L min^???1. The lesser amount of 2A PAHs was found at 700–900°C with airflow rates of 1–3 L min^???1, while less amount of 2B PAHs was found at 700°C and 800°C (with airflow rate of 1–2 L min^???1), at 900°C (with airflow rate of 1–3 L min^???1) and at 1,000°C (with airflow rate of 3 L min^???1). However, the sum total of 2A and 2B PAHs were found to be less at 700–900°C with airflow rate of 1–2 L min^???1.     

Temporal-spatial variability and fractal characteristics of soil nitrogen and phosphorus in Xinji District, Hebei Province, China

Traditional statistics, geostatistics, fractal dimensions, and geographic information systems (GIS) were employed to study the temporal?Cspatial variability of soil total nitrogen (TN) and total phosphorus (TP) levels in Xinji District, Hebei Province area of the North China Plain from 1980 to 2007. The results indicate that nutrient levels follow normal or lognormal distributions. The TN content was 0.59 ±0.155 g kg^???1 in 2007, an increase of 0.44 g kg^???1 compared with that of 1980. In 2007, the TP content was 1.21 ±0.227 g kg^???1, an increase of 0.01 g kg^???1 from 1980. The geostatistical analysis showed that the distribution of these soil nutrients in the study area exhibits a trend and anisotropy. The range and [C ₀/(C ₀?+?C)] of TN and TP in 1980 were all less than in 2007. The ordinary kriging interpolation method was used to analyze the nutrient contents differences between 1980 and 2007. The results indicate that soil TN levels have increased over the 27-year period, and the area where the TN level had increased by at least 0.4 g kg^???1 was about 61.7% of the district. The area where the TP content increased covered about 58.4% of the district. The variance analysis indicated that land-use type had a clear influence on the distribution and change in TN and TP content. Using the 3-D box-counting dimension method combined with GIS, the fractal dimension of soil nutrient spatial distribution over the two periods showed that in 27 years, the fractal dimension of TN increased from 1.95 to 2.02, and the fractal dimension of TP increased from 1.89 to 2.01, indicating that the complexity of the spatial distribution of all nutrient contents had increased. This study can provide a basis for accurate fertilizing and to enhance the conversion of soil characteristics under different spatial scales.     

Spectrophotometric determination of platinum(IV) in alloys, complexes, environmental, and pharmaceutical samples using 4-[N,N-(diethyl)amino] benzaldehyde thiosemicarbazone

4-[N,N-(Diethyl)amino] benzaldehyde thiosemicarbazone (DEABT) is proposed as an analytical reagent for the spectrophotometric determination of platinum(IV). The DEABT forms 1:2 yellow complex with Pt(IV), which is sparingly soluble in water and completely soluble in water–ethanol–DMF medium. The Pt(IV)–DEABT complex shows maximum absorbance at 405 nm. Beer’s law is valid up to 7.80 μg cm^???3, and optimum concentration range for the determination of platinum(IV) is 0.48–7.02 μg cm^???3. The molar absorptivity and Sandell’s sensitivity of the method are found to be 1.755 × 10⁴ dm³ mol^???1 cm^???1 and 0.0012 μg cm^???2, respectively. The relative error and coefficient of variation (n?=?6) for the method does not exceed ±0.43% and 0.35%, respectively. Since the method tolerates a number of metal ions commonly associated with platinum, it can be employed for the determination of platinum in environmental samples, pharmaceutical samples, alloys, catalysts, and complexes. The method is rapid as the Pt(IV)–DEABT complex is soluble in water–ethanol–DMF medium and not requiring any time consuming extraction method for the complex.     

Sediments as a potential tool for assessment of sewage pollution in Barigüi River, Brazil

Sediments constitute a pollutant trap and have proven to be an efficient tool to identify environmental impacts. Sediments are considered a very important means to assess the level of contamination of water bodies because of their ability to accumulate metals and organic. The anthropogenic inputs of sewage, with or without prior treatment, in aquatic environments, affect the geochemical composition of sediment. In addition, the sediment adsorbs hydrophobic compounds found in feces, such as the fecal sterols. The granulometric and geochemical composition of the sediment of Barigüi River-Brazil was investigated. The results show that silt and clay dominate the granulometric composition of the sediments. The geochemical composition of sediments showed high concentrations of phosphorus and nitrogen. The Redfield ratios confirm the inputs of phosphorus and nitrogen. The TOC/N ratio was used to identify the source of pollution. N/TP ratios were found between 1.0 and 3.5. Clearly, an input of phosphorus, sewage is the most acceptable source, following the historic profile of the Barigüi River. High concentration of nitrogen phosphorus labels the area to be polluted by sewage. To confirm the sewage pollution, adsorbed fecal sterols in sediments were investigated. The concentration of total sterols was found between 0.86 and 304.58 μg g^???1. Two distinguished scenario was found, one severely polluted and another slightly polluted. The highest concentrations of total fecal sterols were associated with sediment whose geochemical composition showed higher levels of TOC, as well as higher proportions of silt and clay. Also, epicoprostanol, a coprostanol isomer, was used as an indicator of the level of treatment or age of the fecal matter because it is formed during the treatment of wastewater and sludge digestion. If the treatment of sludge takes a long time, epicoprostanol can form from cholesterol, and relative proportions of those compounds may be used as an indicator of the presence of untreated sewage in the sediments. The epicoprostanol was found in the range between 0.02 and 9.71 μg g^???1; concentration of up to 0.015 μg g^???1 represents situations where there is strong contamination by sewage. All sites investigated showed a concentration of epicoprostanol higher than the value adopted as threshold. The lower concentration of epicoprostanol found for all sites is consistent with the high concentration found for coprostanol, and this is typical for untreated sewage.     

Comparative study based on sediment characteristics and macrobenthic communities in two Italian lagoons

The aims of this study were to analyse sediment characteristics and macrobenthic assemblages in two very close Italian coastal lagoons (Lesina and Varano) and to assess the different behaviour between the two basins and the relationship between sediment matrix and benthic organisms within and between the two lagoons. The comparative study was performed in July 2007 at 13 sampling sites in Lesina lagoon and 15 sites in Varano basin for sediment grain size, total organic carbon (TOC), total nitrogen (TN), total phosphorus (TP) and macrobenthic structure analyses. Both lagoons were generally dominated by fine-grained sediments (clay and silt components). The average contents of TOC and TN measured in Lesina was higher than in Varano (3.31% vs 2.52% for TOC and 5,200 μg·g^???1 vs 3,713 μg·g^???1 for TN); in contrast, the TP was lower (540 μg·g^???1 vs 620 μg·g^???1). Based on macrobenthic community patterns, the central zone in Varano lagoon and the eastern area in Lesina lagoon were characterised by the lowest abundance (168.7 ind·m^???2 and 503.2 ind·m^???2, respectively) and by the lowest number of species, as highlighted by the diversity indices (Shannon–Wiener, H ^′ range was 0.47–1.45 for Lesina and 0.00–1.68 for Varano; Margalef species richness, d range was 0.00–1.67 for Lesina lagoon and 0.00–2.38 for Varano basin). Ordination diagrams suggested an influence of marine and freshwater inputs on the sediment distribution in Varano lagoon and on macrobenthic assemblages in Lesina lagoon.     

A study on the phytoaccumulation of waste elements in wetland plants of a Ramsar site in India

Some wetland plant species are adapted to growing in the areas of higher metal concentrations. Use of such vegetation in remediation of soil and water contaminated with heavy metals is a promising cost-effective alternative to the more established treatment methods. Throughout the year, composite industrial effluents bringing various kinds of heavy metals contaminate our study site, the East Calcutta Wetlands, a Ramsar site at the eastern fringe of Kolkata city (formerly Calcutta), India. In the present study, possible measures for remediation of contaminated soil and water (with elements namely, Ca, Cr, Cu, Pb, Zn, Mn, and Fe) of the ecosystem had been investigated. Ten common regional wetland plant species were selected to study their efficiency and diversity in metal uptake and accumulation. Results showed that Bermuda grass (Cynodon dactylon) had the highest total Cr concentration (6,601 ± 33 mg kg^???1 dw). The extent of accumulation of various elements in ten common wetland plants of the study sites was: Pb (4.4?C57 mg kg^???1 dw), Cu (6.2?C39 mg kg^???1 dw), Zn (59?C364 mg kg^???1 dw), Mn (87?C376 mg kg^???1 dw), Fe (188?C8,625 mg kg^???1 dw), Ca (969?C3,756 mg kg^???1 dw), and Cr (27?C660 mg kg^???1 dw) indicating an uptake gradient of elements by plants as Ca>Fe>Mn>Cr>Zn>Cu>Pb. The present study indicates the importance of identification and efficiency of metal uptake and accumulation capabilities by plants in relation to their applications in remediation of a contaminated East Calcutta Wetland ecosystem.     

Environmental vanadium distribution, mobility and bioaccumulation in different land-use Districts in Panzhihua Region, SW China

In order to characterize environmental vanadium distribution, mobility, and bioaccumulation, a total of 55 soil samples and 36 plant samples were collected in four typical land-use districts in Panzhihua region, Southwestern China. Soil samples were analyzed with the modified Community Bureau of Reference (BCR) sequential extraction procedure, and the content of vanadium in soil and plant was determined by ICP-AES. The total content of vanadium was 208.1?C938.4 mg kg^???1 in smelting area, 111.6?C591.2 mg kg^???1 in mining area, 94.0?C183.6 mg kg^???1 in urban park, and 71.7?C227.2 mg kg^???1 in agricultural area, respectively, while the bio-available content of vanadium was characterized that the polluted areas (mining area 18.8?C83.6 mg kg^???1, smelting area 41.7?C132.1 mg kg^???1) and the unpolluted area (agricultural area 9.8?C26.4 mg kg^???1, urban park 9.9?C25.2 mg kg^???1). In addition, the contamination degree of vanadium in soil was smelting area > mining area > agricultural area ?? urban park. Moreover, the fraction of vanadium in each sequential extraction characterized that residual fraction > oxidizable fraction > reducible fraction > acid soluble fraction. The bioaccumulation of vanadium from soil to plant was weak to intermediate absorption. Therefore, some countermeasures such as soil monitoring and remediation should be to take in the sooner future, especially in mining and smelting area.     

Extraction of ultra traces of polychlorinated biphenyls in aqueous samples using suspended liquid-phase microextraction and gas chromatography-electron capture detection

This study reports the feasibility of applying directly suspended liquid-phase microextraction (DSLPME)-gas chromatography detection for the pre-concentration and determination of low levels of eight polychlorinated biphenyls (PCBs) in aqueous samples. The technique requires minimal sample preparation, analysis time and solvent consumption and represents significant advantages over conventional analytical methods. The experimental parameters such as salt content, sample temperature, stirring rate, extraction time, micro-drop volume and breakthrough volume were investigated and found to have significant influences on DSLPME. Under the optimal experimental conditions, the enrichment factor ranged from 578 to 729, and the recovery was above 93 %. Calibration curves possessed good linearity (R ²?>?0.99) over a wide concentration range of 0.1–10.0 μg L^?1 with limits of detection ranging from 0.01 to 0.07 μg L^?1. The relative standard deviations for 1.0 μg L^?1 of PCBs in water by using internal standard were in the range 2–14 % (n?=?3). The proposed simple, accurate and sensitive analytical method was applied successfully to the determination of trace amounts of PCBs in water samples.     

A study of background radioactivity level for Canakkale, Turkey

This study assesses the level of background radiation for Canakkale province of northwestern Turkey. Radon concentrations in indoor air were determined using CR-39 nuclear track detectors and ²²²Rn activity was found to be 167 Bq m^???3 (equivalent to an annual effective dose of 4.2 mSv). Measurements of outdoor gamma radiation (of terrestrial and cosmic origin) in air were performed using plastic scintillators, and the average absorbed gamma dose rate was found to be 66.4 nGy h^???1 (corresponding to an annual effective dose of 81.4 μSv). The radionuclide activity concentrations in soil samples collected from the study area were measured through gamma-ray spectrometry, and the average activities were determined as 94.55, 110.4, and 1,273 Bq kg^???1 for the natural radionuclides ²³⁸U, ²³²Th, and ⁴⁰K, respectively, and 19.39 Bq kg^???1 for the fission product ¹³⁷Cs. The natural radioactivity sources resulted in an annual effective dose of 184 μSv. The radioactivity levels of drinking water samples were measured as 0.0599 Bq l^???1 for gross-alpha activity and 0.0841 Bq l^???1 for gross-beta activity using a low-background counting technique (equivalent to an annual effective dose of 12.25 μSv). The results of this study show that the activity levels of radon in air, radionuclides in soil, and alpha activities in drinking water are higher compared to the data available for other Turkish cities and the world averages. On the other hand, the outdoor gamma dose rates in air and beta activities in drinking water are within natural limits.     

Polycyclic aromatic hydrocarbons and polychlorinated biphenyls in the harbour of Naples (Southern Italy): time and spatial distribution patterns

Seventeen parent polycyclic aromatic hydrocarbons (PAHs) and 38 congeners of polychlorinated biphenyls were measured at five different sediment depths (between the surface and ~300 cm below the seafloor) at 160 sites in Naples harbour. Total PAH (??PAH) and PCB (??PCB) concentrations ranged between 0.012?C21.73^???nd 0.001?C0.222 mg kg^???1, respectively. For PAHs, an evident and progressive decrease in concentration with depth documents the effects of a more intense anthropic impact of this group of pollutants in the recent period. A selected number of PAH isomer pairs (phenanthrene/anthracene, fluoranthene/pyrene and benzo(a)anthracene/crysene) were used to distinguish between contaminants of pyrolitic and petrogenic origin. More than 90% of PAHs present at the different depths of the studied sediments indicate pyrolitic industrial origins. On the other hand, relatively high concentrations of three- and four-ring PAHs suggest a limited contribution of vehicular emissions to the contamination of sediments. An unexpected and systematic increase of ??PCB concentration, exceeding values approved by international regulations, was found in the studied sediments, testifying to the uncontrolled discharge to the studied area from industrial and commercial activity on nearby land. Ecotoxicological risk levels calculated for PAHs suggests a relatively elevated level of toxicity in surface sediments decreasing with depth and very low toxicity values associated to PCB toxicity.